Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB 26-2341
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2171. Reasons for update: update the Parts list to add a note to clarify the application of the part numbers W520102-S442 and 4S4Z-3N324-AA "FWD Only". Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No relevant diagnostic trouble codes (DTC) present Traceable shudder event with IDS/FDRS reading *(Figure 1)* This condition may be perceived/felt as an engine misfire. This may be due to a concern with the output planetary assembly.
TSB 26-2328
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2194. Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsair) and limited the parts list for Edge/Nautilus to only the rear drive unit fluid. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
TSB 26-2194
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2627. Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
TSB 26-2171
Service Bulletin/Repair Instructions
This article updates TSB 25-2154. Reasons for update: *Parts List *Service Procedure to replace the output planetary carrier assembly *Added 2023-2024 model year vehicles Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No relevant diagnostic trouble codes (DTC) present Traceable shudder event with IDS/FDRS reading *(Figure 1)* This condition may be perceived/felt as an engine misfire. This may be due to a concern with the output planetary assembly.
25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
TSB 26-2092
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2466 to add Bronco Sport, Escape, Maverick and Corsair, as well as removing Expedition and Navigator. One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54589
Other
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various connectivity concerns with The Ford App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.
TSB 25-2627
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2552 to update the Parts List Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
TSB 25-2552
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2351 to update the Service Procedure Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present This may be due to rear drive unit internal (RDU) fluid contamination.
SSM 54262
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2020 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2020 Explorer vehicles equipped with a 3.0L EcoBoost, and 2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. If diagnostics lead to the VCTs as the source of the noise, refer to the 2024 F-150 Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F. Pinpoint test F has been updated to include additional steps along with a video on how to identify the single affected VCT unit that requires replacement.
TSB 25-2466
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
SSM 54116
Service Bulletin/Repair Instructions
Various 2019-2024 Ford and Lincoln vehicles equipped with SYNC 3 may experience a partially or fully black center display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.
TSB 25-2351
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2386 to update the Service Procedure and Part List. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No diagnostic trouble codes DTCs present Note: Three (3) new Essential Special Service Tools (ESSTs) are required to service the internal clutch pack on vehicles equipped with a single active torque rear drive unit (RDU) only. These ESSTs are expected to ship to all dealers (US, Canada, Puerto Rico and Mexico) in September 2025. ESST packages were shipped to 100 selected dealers in the US and Canada in May 2025, based on RDU part sales activity. The RDU Internal Clutch Kit and Adhesive Sealant are currently under restricted ordering to ensure ample supply of parts are available to dealers with the ESSTs. All parts are expected to be available for open order by Q4 2025, when the ESSTs are planned to arrive at all dealers. Note: For dealers with the ESSTs and a vehicle in the service department that requires a repair using the new RDU Internal Clutch
SSM 54067
Service Bulletin/Repair Instructions
For 2018-2024 Edge and 2018-2025 Mustang vehicles, if diagnostics lead to the sun visor as the causal part, a new lower level part is available (DS7Z-9904132-A). It is not necessary to replace the sun visor assembly if only the clip is damaged.
24B47 S1
Other
CERTAIN 2018-2024 MODEL YEAR VARIOUS VEHICLES — UPDATE SYNC SOFTWARE
TSB 25-2154
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No DTCs present Traceable shudder event with IDS/FDRS reading. Refer to Figure 1. Sometimes this is perceived/felt as an engine misfire. This may be due to an internal issue with the torque converter.
SSM 53474
Service Bulletin/Repair Instructions
Some 2019-2024 Edge and 2019-2023 Nautilus vehicles equipped with a 2.0L engine may exhibit a repeat block heater failure.
SSM 53292
Service Bulletin/Repair Instructions
Some 2018-2024 F-150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
SSM 53174
Service Bulletin/Repair Instructions
Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
TSB 24-2331
Service Bulletin/Repair Instructions
Some 2018-2024 F150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
SSM 52820
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off.
24B47
Service Bulletin/Repair Instructions
Certain 2018 - 2024 Model Year Various Vehicles Update SYNC Software In all the affected vehicles, due to an error in the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.
SSM 52722
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
SSM 52704
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
SSM 52675
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
TSB 23-2356
Service Bulletin/Repair Instructions
This TSB supersedes TSB 23-2049 to update the parts list. Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 52076
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a noise from the rear of the vehicle while approaching the vehicle or prior to starting engine. This may be due to the rear drive unit (RDU) actuator learning process. Reprogram the software in the AWD module to minimize the noise using the latest software level of the appropriate Ford diagnostic scan tool. If no other concerns or symptoms are present, further diagnosis or repairs are not recommended. For claiming, use causal part 4000 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52064
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles equipped with all-wheel drive (AWD) may exhibit a noise/vibration/chatter/shudder/grind/bind from the rear of the vehicle during low speed turning events. To correct the condition, reprogram the AWD module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use casual part RECAL and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52051
Service Bulletin/Repair Instructions
Some 2019-2023 Edge/Nautilus and 2022-2023 Maverick vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use causal part 4000.
TSB 23-2307
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
SSM 51838
Service Bulletin/Repair Instructions
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SSM 51823
Service Bulletin/Repair Instructions
Some 2019-2023 Edge/Nautilus, 2020-2023 Escape/Corsair, 2021-2023 Bronco Sport, 2022-2023 Maverick vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use base (4000) causal part.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
TSB 23-2049
Service Bulletin/Repair Instructions
Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
TSB 23-2075
Service Bulletin/Repair Instructions
Some 2018-2019 Edge/Continental, 2018 MKX and 2019 Nautilus vehicles built on or before 1-Aug-2019 and 2018-2019 Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.
SSM 51385
Service Bulletin/Repair Instructions
Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.0L engine may exhibit a repeat block heater failure. This may be caused by air in the engine cooling system. The WSM replacement procedure has been updated to include the Engine Cooling System Draining, Vacuum Filling and Bleeding procedure found in Section 303-03A Engine Cooling - 2.0L EcoBoost (184kW/250PS) MI4, General Procedures as the final step. The block heater should not be tested unless all the air has been removed from the engine cooling system following this procedure.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51248
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, 2019-2020 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-2376
Service Bulletin/Repair Instructions
Some 2019-2022 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
22N02 S1
Service Bulletin/Repair Instructions
Certain 2015-2019 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement REASON FOR THIS SUPPLEMENT Parts Requirements / Ordering Information: Part numbers for Edge and MKX vehicles have been added. Edge and MKX model year updated from 2018 to 2019, build dates remain the same.
SSM 51117
Service Bulletin/Repair Instructions
Some 2021-2022 Bronco Sport 1.5L, 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2022 Maverick vehicles may exhibit an illuminated AWD warning indicator or fault message with diagnostic trouble code (DTC) C0095:71/:19 stored in the all wheel drive (AWD) module. Some 2021-2022 Bronco Sport 2.0L may exhibit an illuminated AWD warning indicator or fault message with DTC C05D9:71, C05E8:71, C05D8:19 and/or C05E7:19 stored in the AWD module. This may be due to a rear drive unit (RDU) motor magnet ring misalignment. RDU assembly replacement is no longer required. To correct the condition, replace the RDU motor which is now available separately for service. Refer to Workshop Manual, Section 205-02 for diagnosis and repair procedures. For claiming use causal part 4C210 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51011
Service Bulletin/Repair Instructions
Some 2018-2022 Ford and Lincoln vehicles equipped with the 8F35 transmission built on or before 16-Mar-2022 may exhibit transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01.
SSM 50982
Service Bulletin/Repair Instructions
Some 2018-2022 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit one of the following if the customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
SSM 50975
Service Bulletin/Repair Instructions
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
SSM 50959
Service Bulletin/Repair Instructions
Some 2019-2022 Edge/Nautilus, 2018-2022 Expedition/Navigator, 2020-2022 Explorer/Aviator vehicles equipped with a family entertainment system may experience the audio is not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
TSB 22-2254
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50873
Service Bulletin/Repair Instructions
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
TSB 22-2225
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
SSM 50726
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50651
Service Bulletin/Repair Instructions
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50502
Service Bulletin/Repair Instructions
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
SSM 50485
Service Bulletin/Repair Instructions
Some 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2021-2022 Bronco Sport vehicles equipped with a 2.0L EcoBoost or 2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. If the diagnostic procedures lead to replacement of the turbocharger assembly, note that a lower level service component has been released K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport for service to replace the actuator, actuator rod and both e-clips instead of a complete turbocharger assembly. When replacing the wastegate actuator, it is required to replace all parts included in the service kit.
SSM 50394
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles built on or before 03-Dec-2020 may exhibit a power liftgate unable to unlatch from both switches after a second unlatch attempt with or without diagnostic trouble code (DTC) U3000:49 stored in the rear gate trunk module (RGTM). If the RGTM is at the latest software level and the condition is still present, refer to the Workshop Manual (WSM) Section 501-03 to perform normal diagnosis.
SSM 50375
Service Bulletin/Repair Instructions
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
SSM 50346
Service Bulletin/Repair Instructions
Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2411
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
TSB 21-2389
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles built on or before 11-Mar-2021 and equipped with a 8F35 transmission may exhibit a shudder/buck/jerk while driving up to 35 mph (57 km/h). This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure steps to reprogram the PCM and the transmission solenoid strategy.
SSM 50251
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50230
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engine and built on or before 14-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0137, P0141 and/or P2096. This may be due to an exhaust gas oxygen sensor seal. To correct the condition, install an updated oxygen sensor, part number K2GZ-9G444-D. Refer to Workshop Manual (WSM), Section 303-14A. For claiming, use casual part 9G444 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2342
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50175
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX, and 2019-2021 Nautilus vehicles may exhibit the parking lamps stay on and/or the trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50171
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus/Ranger, 2020-2021 Escape/Corsair/Explorer, and 2021 Bronco Sport vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. When replacing the wastegate actuator, it is important to replace all parts in the service kit. Turbocharger replacement is not necessary to correct the condition.
TSB 21-2340
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine built on or before 22-Aug-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure steps to replace the crankcase ventilation tube assembly and reprogram the PCM.
TSB 21-2322
Service Bulletin/Repair Instructions
This article supersedes TSB 17-0065 to update the Service Procedure and vehicles affected. Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles built on or before 05-Jun-2019 may exhibit a rattle or flutter noise from the underbody of the vehicle while moving. This may be due to the movement of loose underbody shield fasteners which are attached to the underbody shields. To correct the condition, follow the Service Procedure to remove the assembly aid fasteners.
TSB 21-2294
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50071
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles may exhibit an inoperative power liftgate with or without diagnostic trouble code U3000:49 stored in the rear gate trunk module (RGTM). This may be due to the software in the RGTM. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 50045
Service Bulletin/Repair Instructions
Some 2018-2021 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit an inoperative charging pad, slow charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
SSM 50049
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
SSM 50039
Service Bulletin/Repair Instructions
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-2268
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus/Transit Connect, 2020-2021 Escape/Corsair and 2021 Bronco Sport vehicles equipped with a 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent no reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.
TSB 21-2263
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 49993
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a noise from the rear of the vehicle while approaching the vehicle or prior to starting engine, which is associated with rear drive unit (RDU) actuator learning process. Update the all wheel drive module (AWD) calibration to minimize the noise. If no other concerns or symptoms are present, further diagnosis or repairs are not recommended. For claiming, use causal part 4000 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49931
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX and 2019-2021 Nautilus vehicles may exhibit a hood bounce or flutter condition at high speeds. This may be due to an incorrect adjustment of the rubber bump stops. To correct this condition, make sure the rubber bump stops are in contact with the inner hood sheet metal. Using a piece of paper between the hood and the rubber hood stop, make sure the paper fits snug with hood closed. For claiming, use causal part number 16612 and applicable labor times from Section 12 of the Service Labor Times Standard (SLTS) Manual.
SSM 49924
Service Bulletin/Repair Instructions
Some 2019 MKC, 2019-2021 Edge/Nautilus/Escape/Ranger/Explorer, 2020-2021 Corsair, and 2021 Bronco Sport vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 49914
Service Bulletin/Repair Instructions
Some 2015-2021 Edge, 2016-2018 MKX, 2019-2021 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49885
Service Bulletin/Repair Instructions
Some 2019-2021 Ford and Lincoln vehicles may exhibit an intermittent audio echo/robotic voice heard during a bluetooth phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.
SSM 49820
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49803
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2150
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 49795
Service Bulletin/Repair Instructions
Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 49769
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles equipped with all-wheel drive (AWD) may exhibit a noise/vibration/chatter/shudder/grind/bind from the rear of the vehicle during low speed turning events. To correct the condition, reprogram the AWD module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use casual part RECAL and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49770
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a noise from the rear of the vehicle while approaching the vehicle or prior to starting engine, which is associated with rear drive unit (RDU) actuator learning process. Update the driveline control module (DLCM) calibration to minimize the noise. If no other concerns or symptoms are present, further diagnosis or repairs are not recommended. For claiming, use causal part 4000 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49756
Service Bulletin/Repair Instructions
Some 2018-2021 vehicles supported by FDRS may not list a software update for a module under the SW Updates tab although an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.
SSM 49679
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may require replacement of the roof opening panel track or frame for various conditions. When replacing the roof opening panel, the replacement component may have less magnet plates. In order to prevent any noise vibration or harshness (NVH) concerns, the magnets on the headliner around the roof opening panel that line up with the removed magnet plates should be discarded.
TSB 21-2081
Service Bulletin/Repair Instructions
Some 2019-2021 Edge and 2019-2020 Nautilus vehicles built on or before 11-Mar-2021 and equipped with a 8F35 transmission may exhibit a shudder/buck/jerk while driving up to 35 mph (57 km/h). This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure steps to reprogram the PCM and the transmission solenoid strategy.
SSM 49676
Service Bulletin/Repair Instructions
Some 2021 Mustang Mach-E vehicles may experience a concern of the alarm activating when an unlocked door is opened, the driver door does not unlock/open when pressing the door activation switch, or the door activation switch not lighting up. This may be due to a software configuration in the body control module (BCM). To correct the condition, reprogram the BCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 15604 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49668
Service Bulletin/Repair Instructions
Some 2019-2020 Edge vehicles may exhibit a condition where the rear wiper continuously operates. This may be due to a pinched or damaged wire in the liftgate where the harness enters the liftgate causing a short to ground. To correct the condition, inspect the area where the wiring harness enters the liftgate and repair any damage found to the wiring.
SSM 49571
Service Bulletin/Repair Instructions
Some 2019-2021 Edge/Nautilus, 2020-2021 Escape/Corsair, 2021 Bronco Sport vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events due to fluid contamination. Drain and refill the rear drive unit (RDU), refer to Workshop Manual Section (WSM) 205-02. Drive for 8 km (5 miles) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with WSM diagnostics. For claiming, use base (4000) causal part.
SSM 49565
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles may exhibit an inoperative power liftgate with or without diagnostic trouble code U3000-49 stored in the rear gate trunk module (RGTM). This may be due to the RGTM software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49541
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
SSM 49477
Service Bulletin/Repair Instructions
Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
SSM 49427
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus/Ranger, 2020 Escape and 2020-2021 Corsair/Explorer vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to a missing wastegate actuator e-clip. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. Turbocharger replacement is not necessary for missing wastegate actuator e-clips.
SSM 49328
Service Bulletin/Repair Instructions
Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 49292
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49284
Service Bulletin/Repair Instructions
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
TSB 20-2363
Service Bulletin/Repair Instructions
Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 49266
Service Bulletin/Repair Instructions
Some 2020 Edge/Nautilus vehicles built on 12-Aug-2020 and through 22-Aug-2020 may exhibit a customer concern of the FordPass or Lincoln Way mobile apps unable to connect to the vehicle. The customer may state that there is no activate button on the FordPass or Lincoln Way mobile app. This may be due to the telematics control unit (TCU) module. To correct the condition, reprogram the TCU using As-Built data. For claiming use causal component 14G087 and labor operations from Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49267
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles may exhibit an inoperative power liftgate with diagnostic trouble code (DTC) B144F:79 stored in the rear gate trunk module (RGTM). This may be due to the calibration of the RGTM. To resolve the concern, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual. Do not replace the power strut unless DTC B144F remains after reprograming the RGTM.
SSM 49217
Service Bulletin/Repair Instructions
Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 49179
Service Bulletin/Repair Instructions
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may exhibit the parking lamps stay on and/or the trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2301
Service Bulletin/Repair Instructions
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 49122
Service Bulletin/Repair Instructions
Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
SSM 49088
Service Bulletin/Repair Instructions
Some 2019-2020 Edge vehicles may exhibit an Overspeed Warning message displayed in the IPC. The warning may display at 118 km/h (73 mph). To correct the condition, perform an as-built configuration of the IPC using the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
SSM 49091
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles may exhibit a false traction control or yaw control event. This may be due to software in the anti-lock braking system (ABS) module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2B373 and labor times in Section 02 of the Service Labor Time Standards (SLTS) Manual.
SSM 49084
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2259
Service Bulletin/Repair Instructions
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure
TSB 20-2233
Service Bulletin/Repair Instructions
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
SSM 48991
Service Bulletin/Repair Instructions
Some 2015-2020 F150/Edge/Fusion, 2016-2018 MKX, 2019-2020 Nautilus, and 2017-2020 Continental vehicles equipped with 2.7L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or knock sensor wiring harness. To correct the condition, replace the 12A648 ECT sensor and 12A699 knock sensor. Do not disconnect the ECT sensor from the knock sensor harness in case parts are called back for analysis. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2234
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P044C, P1026, P1285, P1299, P139A and/or P2457 stored in the powertrain control module (PCM). The vehicle may also exhibit low coolant level, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), and/or an external coolant leak. This may be due to the exhaust gas recirculation (EGR) cooler and/or settings in the PCM software. To resolve the condition, inspect the EGR cooler and/or update the PCM software.
SSM 48935
Service Bulletin/Repair Instructions
Some 2019 F-150/Ranger/Continental/Edge/Nautilus/Mustang/Fusion/MKZ vehicles may experience voice prompts that skip or have short pauses while directions are being provided. Engineering is currently working on a solution for this condition. Please inform customers that Ford is developing a software fix that is expected in early August. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early August 2020. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
SSM 48929
Service Bulletin/Repair Instructions
Some 2019 F-150/Ranger/Continental/Edge/Nautilus/Mustang/Fusion/MKZ vehicles may experience voice prompts that skip, hiccup or have short pauses while directions are being provided. No repairs should be made to attempt to correct this condition. Engineering is currently working on a solution for this condition. Please inform customers that Ford is developing a software fix that is expected in early August. Let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early to mid August 2020. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
SSM 48908
Service Bulletin/Repair Instructions
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
TSB 20-2194
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles may exhibit a slow fuel fill and/or spit back during refueling. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 20-2190
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit a harsh engagement when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE with no DTCs present. The vehicle may also exhibit a harsh upshift and downshift. These harsh engagements may result in an engagement clunk from the driveline. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 20-2151
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines built on or before 24-Jan-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittently stuck open brake vacuum tube assembly causing an uncommanded high air flow intake manifold leak. To resolve the condition, replace the brake vacuum tube assembly.
SSM 48757
Service Bulletin/Repair Instructions
Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 48608
Service Bulletin/Repair Instructions
SSM 48608 - 2019 Edge - Ambient Air Temperature Inaccurate Some 2019 Edge vehicles may exhibit an incorrect or inaccurate ambient air temperature (AAT) reading. This may be due to the software in the front controls interface module (FCIM). To correct the condition, reprogram the FCIM with the latest software level of the appropriate Ford scan tool. For claiming use causal part 18842 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48579
Service Bulletin/Repair Instructions
Some 2018-2020 vehicles equipped with the 8F24, 8F35, 8F40, or 8F57 transmissions may have a trace amount of transmission fluid in the main control electrical connector. This is due to the connector being submerged in transmission fluid during the main control manufacturing process. A trace amount should be considered normal and will not affect the function of the transmission. Do not attempt a repair for this condition. If more than a trace amount of fluid is found, follow normal diagnostics in the Workshop Manual(WSM), Section 307-01>Diagnosis and Testing>Leakage Inspection.
SSM 48558
Service Bulletin/Repair Instructions
SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48430
Service Bulletin/Repair Instructions
Some 2018-2020 Escape/Corsair, Edge, Explorer, Fusion, Transit Connect Vehicles equipped with a TCU may exhibit a "Battery Backup Component Failure" message in the cluster. This may be accompanied by DTC 1477-09 - Backup Battery Component Failure. This may be due to the TCU experiencing a sudden temperature change. To correct this condition, reprogram the TCU using the appropriate Ford diagnostic scan tool. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-2386
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Nautilus/Transit Connect and 2020 Escape/Corsair vehicles equipped with a 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent no reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.
TSB 19-2387
Service Bulletin/Repair Instructions
Some 2018-2019 Edge/Continental, 2018 MKX and 2019 Nautilus vehicles built on or before 1-Aug-2019 and 2018-2019 Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.
SSM 48364
Service Bulletin/Repair Instructions
Some 2018-2019 Expedition/Navigator, 2019 Edge/Nautilus, 2020 Explorer/Aviator vehicles equipped with a family entertainment system may experience an issue where the audio not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
SSM 48345
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/Escape/Nautilus/Corsair vehicles equipped with 2.0L EcoBoost engines may exhibit low coolant, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), external coolant leaking, and/or illuminated MIL with DTCs P0217, P0401, P1026, P1285, P1299, P2196 or P2467 stored in the PCM. This may be due to an EGR Cooler that is leaking coolant into the engine intake and exhaust system. The EGR cooler should be inspected first to detect the presence of any internal leaks by a visual inspection and a pressure test as defined in the Workshop Manual (WSM). If any coolant is found leaking from the coolant chamber into the exhaust chamber, replace the EGR cooler. If no issues are detected with the EGR cooler, continue repair diagnosis using standard diagnostic procedures as defined in the WSM.
SSM 48336
Service Bulletin/Repair Instructions
Some 2019 F150, Ranger, Continental, Edge, Nautilus, Mustang, Fusion or MKZ may experience voice prompts that skip, hiccup or have short pauses while directions are being provided. No repairs should be made to attempt to correct this condition. Engineering is currently investigating the concern. Monitor Oasis for updates.
TSB 19-2331
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with an 8F35 transmission and built on or before 10-Sep-2019 may exhibit a harsh upshift and downshift, harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE. These harsh engagements may result in an engagement clunk from the driveline. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 48316
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
TSB 19-2313
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit a harsh upshift and downshift, harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE with no DTCs present. These harsh engagements may result in an engagement clunk from the driveline. The vehicle may also exhibit a 4th to 5th gear upshift flare. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 48260
Service Bulletin/Repair Instructions
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
TSB 19-2288
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles may exhibit harsh/bumpy upshift/downshifts, harsh engagements from PARK to REVERSE, PARK to DRIVE, REVERSE to DRIVE or DRIVE to REVERSE. The vehicle may also exhibit an upshift flare from 4th to 5th gear during the first shift after a cold start. This may be due to the shift strategy in the powertrain control module (PCM). Follow the Service Procedure.
TSB 19-2282
Service Bulletin/Repair Instructions
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 16 kph (10 mph), the rear view camera remains on the screen at speeds below 16 kph (10 mph), or inoperative infotainment applications. This may be due to the SYNC 3 software version installed on the vehicle. To correct the condition, follow the Service Procedure steps to reprogram the accessory protocol interface module (APIM).
TSB 19-2224
Service Bulletin/Repair Instructions
Some 2019 Edge vehicles built on or before 06-Mar-2019 may exhibit a popping or snapping noise from the rear of the vehicle when the liftgate is opened or closed. This may be due to reversing lamp close out interference caused by the securing tabs. To correct the condition, follow the Service Procedure steps to replace the reversing lamp close out. A lower level service part has been released. Replacement of the reversing lamp assembly is not required. To correct the condition, follow the Service Procedure steps on vehicles that meet the following criteria: * 2019 Edge * Built on or before 06-Mar-2019 * Popping/snapping noise when opening or closing the liftgate
SSM 48135
Service Bulletin/Repair Instructions
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
TSB 19-2249
Service Bulletin/Repair Instructions
Some 2018-2019 Edge/Continental/Fusion/MKZ, 2018 MKX, and 2019 Nautilus vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal.To correct the condition, follow the Service Procedure.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
SSM 48108
Service Bulletin/Repair Instructions
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 48094
Service Bulletin/Repair Instructions
Some 2015-2019 Edge vehicles build on or before 5-Nov-2018 may exhibit snow and/or ice accumulation below the wiper blade park position, causing the wipers to have intermittent operational issues. If normal diagnostics do not result in a root cause determination, replace the drivers side wiper motor with updated service part FT4Z-17508-H, and make sure the customer is advised to keep the cowl area clean of ice and snow. Refer to Workshop Manual (WSM), Section 501-16 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 48095
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and or REVERSE to DRIVE. These harsh engagements may result in an engagement clunk from the driveline. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
TSB 19-2213
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus/Transit Connect vehicles equipped with a 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent or delayed reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.
SSM 48045
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with all-wheel drive (AWD) may exhibit an AWD System Disabled message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) C0095:99. This may be due to the calibration of the AWD module. Using the latest software level of the appropriate Ford diagnostic scan tool, reprogram the AWD module. For claiming, use causal part 4000 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
TSB 19-2172
Service Bulletin/Repair Instructions
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 48029
Service Bulletin/Repair Instructions
Some 2018-2019 F-150 vehicles built on 23-Sep-2018 and through 28-Mar-2019 and 2019 Edge/Nautilus/Continental/MKZ vehicles built on 4-Dec-2018 and through 29-Mar-2019 and Fusion vehicles built on 16-Jan-2019 and through 12-Apr-2019 equipped with a 2.7L/3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). This may be due to the incorrect positive crankcase ventilation (PCV) valve installed. If the PCV valve is brown in color, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for normal diagnostics. If the PCV valve is gray in color, replace the PCV valve, clear the DTC, and retest. If the DTC returns, refer to the PC/ED for normal diagnostics.
SSM 48007
Service Bulletin/Repair Instructions
2019 Edge and Nautilus vehicles, equipped with AWD and built on 22-Jan-2019 and through 03-Mar-2019, exhibit a noise from the rear of the vehicle when a door is opened or after KOEO/KOER. The rear drive unit (RDU) in these vehicles uses a brushless DC motor to vary the amount of torque to the rear axle, and during functional verification, it produces a noticeable noise that is a normal function of the RDU. If the noise appears abnormally loud, it is recommended to compare the noise from the customers vehicle with a 2019 AWD Edge or Nautilus built before 22-Jan-2019 or after 03-Mar-2019, in a similar environment (i.e. both outside). If the noise in the customers vehicle is determined to be significantly louder than a similar vehicle built outside the build dates, do not disassemble the RDU for further diagnosis, an updated RDU assembly is available.
19B11
Service Bulletin/Repair Instructions
Certain 2019 Model Year Edge Vehicles With Adaptive LED Headlamps - Headlamp Control Module Reprogram
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47967
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47948
Service Bulletin/Repair Instructions
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 19-2095
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines built on or before 15-Mar-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittently stuck open brake vacuum tube assembly causing an uncommanded high air flow intake manifold leak. To resolve the condition, replace the brake vacuum tube assembly.
SSM 47925
Service Bulletin/Repair Instructions
SSM 47925 - 2019 Various Vehicles - SYNC 3 - Infotainment Screen Concerns, Wi-Fi ConnectionMessage, Rear View Camera Operation Some 2019 vehicles equipped with SYNC 3 may have the following intermittent symptoms: a Wi-Fi connection pop up every key cycle, frozen unresponsive screen, a solid blue screen when moving forward at speeds above 10 mph, the rear view camera remains on the screen at speeds below 10 mph, or poor App performance. To resolve this concern, check for a SYNC software update under the OASIS Tab SYNC selection. If an update is available, update the APIM software per Workshop Manual (WSM), Section 415-00. Follow the onscreen instructions provided by the programming process. To verify success after programming, turn the key off with the dooropen for 5 minutes. Perform this SYNC programming before taking any other repair steps. For claiming, use causal part 14G371 and applicable labor operations inSection 10 of the SLTS manual. APPLICABLE VEHICLES
SSM 47922
Service Bulletin/Repair Instructions
SSM 47922 - Various Vehicles - 2.7L/3.0L EcoBoost Engine - Oil Filter Service Tip When servicing the oil filter on vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.
TSB 19-2103
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with a 8F57 transmission and built on or before 01-Mar-2019 may exhibit harsh/bumpy upshift, downshift and/or engagement concerns. This may be due to various powertrain control module (PCM) software parameters for upshift flares, stationary and rolling engagements, and coasting downshift bumps. To resolve the condition, reprogram the PCM. Follow the Service Procedure steps to correct the condition on vehicles that meet all the following criteria: 2019 Edge/Nautilus 8F57 transmission Built on or before 01-Mar-2019 Harsh/bumpy upshift, downshift and/or engagement concerns
TSB 19-2104
Service Bulletin/Repair Instructions
Some 2019 Edge and Nautilus vehicles built on or before 14-Nov-2018 equipped with a power liftgate may exhibit a discharged battery, interior lamps cycling on and off erratically and/or a Liftgate Ajar message in the instrument panel cluster (IPC) when the liftgate/doors are shut. This may be due to the calibration of the rear gate trunk module (RGTM) keeping the module awake. Reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool.
SSM 47873
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles built on or before 07-Mar-2019 may exhibit an inoperative power liftgate with diagnostic trouble code (DTC) B144F:79 stored in the rear gate trunk module (RGTM). This may be due to the calibration of the RGTM. To resolve the concern, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47854
Service Bulletin/Repair Instructions
Some 2017-2019 F-Super Duty, 2017-2019 Continental, 2016-2019 Edge, 2016-2018 MKX, 2019 Nautilus vehicles may exhibit a U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47846
Service Bulletin/Repair Instructions
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 10 mph, the rear view camera remains on the screen at speeds below 10 mph, or inoperative infotainment applications. To resolve this concern, check for a SYNC software update under the OASIS Tab SYNC selection. If an update is available, update the APIM software per WSM section 415-00. After the complete pop-up appears, remove the USB flash drive and install it into the IDS tool to update the Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes, which is critical for a successful installation. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47844
Service Bulletin/Repair Instructions
Some 2019 Mustang/Fusion/Edge/F-150/Continental/MKZ/Nautilus/Ranger vehicles with SYNC 3 may show a pop-up message every key cycle that states Network Connection Needed - To complete the system updates your vehicle should connect to a Wi-Fi network or through the FordPass/LincolnWay app. Until the update is completed, some features may not be available. Would you like to attempt to connect to a Wi-Fi network now? This message may occur, even if SYNC has been connected to a trusted Wi-Fi source. To temporarily remove the inconvenience of this pop-up message, advise the customer from SYNC to select Settings > Automatic Updates > System Wi-Fi and turn off System Wi-Fi, then turn off automatic system updates. Engineering is investigating, monitor OASIS for updates.
SSM 47824
Service Bulletin/Repair Instructions
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47817
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittent stuck open brake vacuum on demand valve causing an uncommanded high air flow intake manifold leak. Inspect the vacuum on demand valve (K2GC-2420-AD/K2GZ-2420-A). The Powertrain Controls and Emissions Diagnosis (PC/ED) Manual Pinpoint Test HG and Workshop Manual are being updated to include a diagnostic routine for the vacuum on demand valve and a procedure to remove and install the vacuum on demand valve. Engineering is investigating, monitor OASIS for updates.
TSB 19-2046
Service Bulletin/Repair Instructions
Some 2019 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine, built on or before 23-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P02EE, P02EF, P02F0, P02F1, P044C, P1285, P1299, and/or P2196 stored in the powertrain control module (PCM). This may be due to various settings in the PCM software. To resolve the condition, update the PCM software.
SSM 47814
Service Bulletin/Repair Instructions
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
SSM 47810
Service Bulletin/Repair Instructions
Some 2019 Edge Equipped With Adaptive Headlamps (High Series lamp - Titanium (301A) and ST (401A)) may be reported that the front headlamp lights are not bending while the vehicle is moving through a curve at speeds above 5 kph (3 mph), or that the system check outlined in the owner guide for this feature indicates the feature is not working correctly. Engineering is aware of this issue and is working on a repair solution. The headlamps will continue to function to fully meet all applicable lighting requirements. Do not attempt any diagnosis or repairs for this issue. Continue to monitor OASIS for updates.
SSM 47791
Service Bulletin/Repair Instructions
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47775
Service Bulletin/Repair Instructions
Some 2019 Mustang/Fusion/Edge/F-150/Continental/MKZ/Nautilus with SYNC 3 may show a pop-up message every key cycle that states Network Connection Needed - To complete the system updates your vehicle should connect to a Wi-Fi network or through the FordPass/LincolnWay app. Until the update is completed, some features may not be available. Would you like to attempt to connect to a Wi-Fi network now? This message may occur, even if SYNC has been connected to a trusted Wi-Fi source. To temporarily remove the inconvenience of this pop-up message, advise the customer from SYNC to select Settings > Automatic Updates > System Wi-Fi and turn off System Wi-Fi, then turn off automatic system updates. Engineering is investigating, monitor OASIS for updates
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 47741
Service Bulletin/Repair Instructions
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Edge or Nautilus with SYNC 3 may have a symptom of a rear view camera that remain on the screen when moving forward above 5MPH or a solid blue screen once the vehicle is at cruising speed. Some vehicles may experience inoperative infotainment applications such as Apple CarPlay. To eliminate these symptoms from occurring, it is recommended to disable the Wi-Fi in the settings menu by selecting Automatic updates. Shut off system WIFI and then disable automatic updates. If the vehicle is stuck in the rear camera state you can exit this state by shutting the vehicle off and powering the system down for at least three minutes. Engineering is investigating, monitor OASIS for updates.
TSB 18-2378
Service Bulletin/Repair Instructions
Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a fuel slosh noise primarily when the fuel tank is over 3/4 full and when driving at low speeds. This may be due to the fuel moving around in the fuel tank. Follow the Service Procedure steps to correct the condition.
SSM 47711
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
SSM 47708
Service Bulletin/Repair Instructions
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Edge or MKX with SYNC 3 may have a symptom of a rear view camera that remain on the screen when moving forward above 5MPH or a solid blue screen once the vehicle is at cruising speed. To eliminate this symptom from occurring, it is recommended to disable the Wi-Fi in the settings menu by selecting Automatic updates. Shut off system WIFI and then disable automatic updates. If the vehicle is stuck in the rear camera state you can exit this state by shutting the vehicle off and powering the system down for at least three minutes. Engineering is investigating, monitor OASIS for updates.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47682
Service Bulletin/Repair Instructions
Some 2019 Focus/Transit Connect/Edge/Nautilus vehicles equipped with 8F35 transmission may exhibit an appearance of a fluid leak or weep from transmission axle shaft seal. This condition may be caused by excessive internal seal (dark brown) grease lubricant that is applied during manufacturing of the axle seals. With a suitable cloth, clean the grease from the transmission seal and housing with Motorcraftù Metal Brake Parts Cleaner or equivalent. If the fluid is red, refer to Workshop Manual (WSM), Section 307-01 for normal diagnostics.
SSM 47662
Service Bulletin/Repair Instructions
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 47638
Service Bulletin/Repair Instructions
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.