Vehicle report

2016 FORD EXPEDITION

Compare every FORD EXPEDITION yearNHTSA and EPA records

Service bulletins

109 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

25N15 S1

Other

Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement

SSM 54601

Service Bulletin/Repair Instructions

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

TSB 25-2570

Service Bulletin/Repair Instructions

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

SSM 54366

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

SSM 53040

Service Bulletin/Repair Instructions

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

TSB 24-2188

Service Bulletin/Repair Instructions

This article supersedes TSB 22-2219 to update the Parts List and Service Procedure to clarify applicable steps by vehicle application. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

TSB 24-2165

Service Bulletin/Repair Instructions

This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

SSM 52476

Service Bulletin/Repair Instructions

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

SSM 52314

Service Bulletin/Repair Instructions

During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

SSM 51962

Service Bulletin/Repair Instructions

Some 2016-2018 F-150 and 2016-2017 Expedition/Navigator vehicles may require pressure bleeding of the brake system. The brake system pressure bleeding procedure in the Workshop Manual (WSM), Section 206-00, has been updated to add a warning to not apply the brake pedal or master cylinder damage may occur.

SSM 51536

Service Bulletin/Repair Instructions

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

TSB 22-2219

Service Bulletin/Repair Instructions

Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 (non-Raptor) vehicles equipped with 4WD may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure to remove and cap the vacuum supply line or to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

SSM 50804

Service Bulletin/Repair Instructions

Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

SSM 50375

Service Bulletin/Repair Instructions

Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

SSM 50067

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 50039

Service Bulletin/Repair Instructions

Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

TSB 21-2175

Service Bulletin/Repair Instructions

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

SSM 49821

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 20-2307

Service Bulletin/Repair Instructions

Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.

SSM 49210

Service Bulletin/Repair Instructions

Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

SSM 49086

Service Bulletin/Repair Instructions

Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 20-2255

Service Bulletin/Repair Instructions

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

TSB 20-2233

Service Bulletin/Repair Instructions

This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

SSM 48911

Service Bulletin/Repair Instructions

SSM 48908

Service Bulletin/Repair Instructions

Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

TSB 20-2189

Service Bulletin/Repair Instructions

This article supersedes TSB 20-2028 to update the description of Labor Operation D. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

SSM 48619

Service Bulletin/Repair Instructions

SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

TSB-20-2028

Service Bulletin/Repair Instructions

Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.

TSB 20-2013

Service Bulletin/Repair Instructions

SSM 48423

Service Bulletin/Repair Instructions

Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 48340

Service Bulletin/Repair Instructions

Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

TSB 19-2252

Service Bulletin/Repair Instructions

Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with four wheel drive (4WD) may exhibit an intermittent grinding noise while driving in two wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to replace the worn vacuum and/or IWE components.

SSM 48130

Service Bulletin/Repair Instructions

Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

SSM 48123

Service Bulletin/Repair Instructions

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

SSM 48103

Service Bulletin/Repair Instructions

Some 2015-2017 Expedition/Navigator front and rear bumper parking aid sensor harnesses FL7Z-15K867-A and BL7Z-15K868-A are currently not available. It is recommended that dealers repair or rebuild these harnesses until harnesses become available. For harness FL7Z-15K867-A, use 9U2Z-14S411-CC pigtail kits for C1428, C1429, C1430, and C1431 (front parking sensor connectors), use CU2Z-14S411-MA pigtail kits for C1322, C1323, C1750 and C1751 (fog lights and DRLs), and CU2Z-14S411-ADA for C110 (bumper-to-body harness). For the BL7Z-15K868-A harness, use 9U2Z-14S411-CC pigtail kits for C4009, C4010, C4011, and C4012 (rear parking sensors), use FU2Z-14S411-DB for C494 (bumper-to-body harness). For unused/open cavities, cut the pigtail wire 1" from the connector and use heat shrink to seal the wire to prevent water entry.

SSM 48070

Service Bulletin/Repair Instructions

Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.

SSM 48053

Service Bulletin/Repair Instructions

Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

SSM 47976

Service Bulletin/Repair Instructions

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

SSM 47850

Service Bulletin/Repair Instructions

Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 47948

Service Bulletin/Repair Instructions

SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

SSM 47927

Service Bulletin/Repair Instructions

SSM 47927 - 2017 F-Super Duty, 2016-2017 Expedition/Navigator, 2016-2018 Focus/Fiesta - Radio Reverting To AM Or FM After Vehicle Shut Down and Start Up Some 2017 F-Super Duty, 2016-2017 Expedition/Navigator and 2016-2018 Focus/Fiesta vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.

SSM 47824

Service Bulletin/Repair Instructions

Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47797

Service Bulletin/Repair Instructions

Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

TSB 19-2026

Service Bulletin/Repair Instructions

Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

SSM 47769

Service Bulletin/Repair Instructions

Some 2016-2017 Expedition/Navigator vehicles equipped with rear volume control may experience an inability to control the volume from the rear volume control after an APIM replacement and/or reprogramming. Reprogram the APIM using the standard programming method outlined in the Workshop Manual (WSM) Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 47749

Service Bulletin/Repair Instructions

Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

SSM 47711

Service Bulletin/Repair Instructions

Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

SSM 47662

Service Bulletin/Repair Instructions

For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

SSM 47617

Service Bulletin/Repair Instructions

Some 2017 F-Super Duty, 2016-2017 Expedition/Navigator and 2016-2018 Focus/Fiesta vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.

SSM 47538

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

TSB 18-2273

Service Bulletin/Repair Instructions

Some 2013-2018 F-150/Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. Follow the Service Procedure steps to correct the condition.

SSM 47444

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 47394

Service Bulletin/Repair Instructions

Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Prior approval for short block replacement is not required under new vehicle limited warranty coverage.

SSM 47376

Service Bulletin/Repair Instructions

Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Short block replacement does not require prior approval.

SSM 47379

Service Bulletin/Repair Instructions

Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47380

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 47360

Service Bulletin/Repair Instructions

Some 2013-2018 F-150 and 2017-2018 Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. This may be caused by an intermittent leak in the check valve. Before completing any normal diagnosis suspect that the check valve is the root cause of the issue. If the check valve has been ruled out as the root cause for the issue refer to Work Shop Manual 308-07 and follow normal diagnosis.

SSM 47211

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 47201

Service Bulletin/Repair Instructions

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.

SSM 47167

Service Bulletin/Repair Instructions

Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47141

Service Bulletin/Repair Instructions

Some 2013-2018 F-150/Expedition/Navigator 4x4 vehicles may exhibit an intermittent grinding noise coming from the right front or left front wheel area while accelerating in 2WD mode. Refer to the Workshop Manual (WSM), Section 308-07, Diagnosis and Testing Symptom Chart - NVH > The front axle makes noise in 2H mode only and generally under heavy throttle.

SSM 47080

Service Bulletin/Repair Instructions

2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

SSM 47041

Service Bulletin/Repair Instructions

SSM 47009

Service Bulletin/Repair Instructions

The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

SSM 46951

Service Bulletin/Repair Instructions

Some 2016-2018 F-150 and Expedition vehicles equipped with a SYNC non-touchscreen display may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

SSM 46947

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 46948

Service Bulletin/Repair Instructions

Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.

SSM 46949

Service Bulletin/Repair Instructions

SSM 46930

Service Bulletin/Repair Instructions

Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

SSM 46900

Service Bulletin/Repair Instructions

Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

SSM 46860

Service Bulletin/Repair Instructions

SSM 46861

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

SSM 46848

Service Bulletin/Repair Instructions

Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.

SSM 46834

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 46813

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.

SSM 46802

Service Bulletin/Repair Instructions

Some 2016 - 2017 Expedition/Navigator vehicles may exhibit a no start condition with DTC P025A being stored. This may be due to a pin push-out condition at pin 14 of connector C139, circuit CE608 (VT/GN), on either the 14405 or 12A581 harness side of the connector. Inspect Pin 14 for proper retention and repair the harness as needed. For claiming, use causal part 14405 or 12A581 as appropriate, and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.

TSB 17-2068

Service Bulletin/Repair Instructions

Some 2016-2017 Edge, Escape, Expedition, Fiesta, Flex, MKC, MKT, MKX, Mustang, Navigator and Taurus or 2017 Explorer and Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 Å'C to 5 Å'C (23 Å'F to 41 Å'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.

SSM 46486

Service Bulletin/Repair Instructions

SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

SSM 46474

Service Bulletin/Repair Instructions

SOME 2015-2017 EXPEDITION/NAVIGATOR VEHICLES EQUIPPED WITH EPAS STEERING MAY EXHIBIT NO COMMUNICATION WITH THE PSCM. THIS MAY BE DUE TO AN OPEN 125 AMP MEGA FUSE, LOCATED ON THE POSITIVE BATTERY TERMINAL. IF AN OPEN FUSE IS FOUND, THIS MAY HAVE BEEN CAUSED BY JUMP STARTING THE VEHICLE FROM THE EYELET/POST ON THE FUSE OUTPUT. IT MAY ALSO BE CAUSED BY AFTERMARKET ACCESSORIES ATTACHED TO THIS EYELET POST, OR ACCIDENTAL CONTACT TO GROUND AT THIS LOCATION. IF NONE OF THESE ISSUES ARE FOUND, FOLLOW NORMAL DIAGNOSTICS.

SSM 46451

Service Bulletin/Repair Instructions

2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.

SSM 46295

Service Bulletin/Repair Instructions

TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

TSB 17-0001

Service Bulletin/Repair Instructions

SOME 2011-2016 EXPEDITION AND NAVIGATOR VEHICLES MAY EXHIBIT A RATTLE NOISE FROM THE ROOF OPENING PANEL SHIELD WHILE DRIVING OVER BUMPS. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

SSM 46283

Service Bulletin/Repair Instructions

SOME OWNERS OF 2016 FORD AND LINCOLN MKX VEHICLES EQUIPPED WITH SYNC 3 MAY INQUIRE ABOUT UPGRADING TO APPLE CARPLAY AND ANDROID AUTO. THIS UPGRADE IS NOT CURRENTLY AVAILABLE FOR THOSE VEHICLES. APPLE CARPLAY AND ANDROID AUTO ARE CURRENTLY AVAILABLE ONLY ON VEHICLES EQUIPPED WITH SYNC 3 V2.0 OR LATER. THIS UPGRADE FOR 2016 FORD AND LINCOLN MKX VEHICLES WILL BE AVAILABLE IN 2017. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.

SSM 46210

Service Bulletin/Repair Instructions

SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

SSM 46153

Service Bulletin/Repair Instructions

SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.

SSM 46132

Service Bulletin/Repair Instructions

SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

TSB 16-0139

Service Bulletin/Repair Instructions

SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

SSM 46102

Service Bulletin/Repair Instructions

Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

SSM 46085

Service Bulletin/Repair Instructions

The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

SSM 46073

Service Bulletin/Repair Instructions

Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

SSM 46048

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.

SSM 46016

Service Bulletin/Repair Instructions

SOME 2016-2017 EXPEDITION AND NAVIGATOR VEHICLES BUILT ON OR BEFORE 08/12/2016 AND 2016 F150 VEHICLES BUILT ON OR BEFORE 08/09/2016 EQUIPPED WITH SIRIUS SATELLITE RADIO MAY EXHIBIT AN INTERMITTENT CONCERN WHERE THE AUDIO CUTS OUT AND THE RADIO DISPLAYS A NO SIGNAL MESSAGE WHILE DRIVING IN OPEN SKY CONDITIONS IN CERTAIN LOCATIONS IN YOUR AREA. THIS MAY BE DUE TO INTERFERENCE WITH CELLULAR PHONE TOWER SIGNALS. IF A VEHICLE DISPLAYS THIS CONDITION NEAR CELLULAR PHONE TOWERS, REPLACE THE AUDIO UNIT ANTENNA WITH PART NUMBER GL1Z-10E893-AC ON EXPEDITION/NAVIGATOR AND HL3Z-10E893-AA FOR F150. REFER TO WORKSHOP MANUAL(WSM), SECTION 415-00 FOR REMOVAL AND INSTALLATION INSTRUCTIONS. USE APPLICABLE LABOR OPERATION(S)IN THE SLTS MANUAL SECTION 11.

SSM 46012

Service Bulletin/Repair Instructions

SOME 2016 FOCUS, C-MAX, FIESTA, EXPEDITION, AND NAVIGATOR VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A CONDITION IN WHICH THE SIRIUS SATELLITE CHANNEL GUIDE CATEGORY BUTTONS MAY NOT RESPOND WHEN SELECTED AND A LOADING MESSAGE IS DISPLAYED CONTINUOUSLY. TO CORRECT THIS CONDITION REPROGRAM THE AUDIO CONTROL MODULE (ACM) WITH LATEST CALIBRATION USING IDS RELEASE 101.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 19C107 AND REFER TO SECTION 10 OF THE SLTS MANUAL FOR APPLICABLE LABOR OPERATIONS. THE SYNC VERSION CAN BE DETERMINED VIA OASIS.

SSM 45968

Service Bulletin/Repair Instructions

SOME 2016 ESCAPE/MKC/FIESTA/F150/EXPEDITION/NAVIGATOR/MUSTANG /TRANSIT/FOCUS/C-MAX/MKX/TAURUS/MKS/FLEX/MKT/EDGE AND 2017 ESCAPE/EXPLORER/MKC/FUSION AND MKZ VEHICLES EQUIPPED WITH SYNC 3 MIGHT EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. ENGINEERING IS AWARE OF THIS POSSIBILITY AND IT IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORTATION MODE. IT IS BENEFICIAL TO EXTENDED BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. IF THE VEHICLE SHOULD EXHIBIT A BLANK SCREEN OR OTHER SYNC SYMPTOMS AFTER IT HAS BEEN TAKEN OUT OF TRANSPORT MODE, REFER TO WORKSHOP MANUAL, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

SSM 45916

Service Bulletin/Repair Instructions

SOME 2016 FORD AND LINCOLN VEHICLES EQUIPPED WITH SYNC 3 AND NAVIGATION ALONG WITH A VALID PAID SUBSCRIPTION TO SIRIUS TRAVEL LINK MAY NOT DISPLAY SIRIUS TRAVEL LINK FUEL PRICES. REPLACING COMPONENTS WILL NOT RESOLVE THE CONDITION AND IS NOT RECOMMENDED AT THIS TIME. ENGINEERING IS CURRENTLY INVESTIGATING. IN THE INTERIM, THE FOLLOWING STEPS WILL RESET THE SYSTEM. POSITION THE VEHICLE OUTDOORS IN OPEN SKY. DISCONNECT THE BATTERY FOR 5 MINUTES. RECONNECT THE BATTERY AND START THE VEHICLE. SELECT SIRIUS TRAVEL LINK THEN FUEL PRICES. FUEL PRICE INFORMATION MAY NOT DISPLAY FOR UP TO 15 MINUTES WHILE THE SYSTEM IS UPDATING. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.

SSM 45917

Service Bulletin/Repair Instructions

SOME 2016-2017 VEHICLES EQUIPPED WITH SYNC 3 MAY EXPERIENCE THE FOLLOWING CONCERNS; THE GPS NOT TRACKING THE VEHICLE POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.

SSM 45918

Service Bulletin/Repair Instructions

SOME 2016-2017 FORD/LINCOLN VEHICLES WITH SYNC 3 MAY SEE A NAVIGATION FAULT MESSAGE APPEAR ON THE MAP ON THE HOME SCREEN OR A SYSTEM LOCK UP WHEN THE PHONE IS CONNECTED. APPLINK MAYBE INOPERATIVE, OR THE SYSTEM MAY PERFORM RANDOM REBOOTS DURING AN IGNITION CYCLE WITH THE PHONE CONNECTED. DETERMINE IF THE CUSTOMER HAS AN ANDROID PHONE WITH THE BASEBALL APPLICATION MLB.COM AT BAT INSTALLED. IF THE CUSTOMER DOES NOT HAVE THIS APPLICATION LOADED THEN PROCEED TO THE WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. IF THE CUSTOMER DOES HAVE THIS APPLICATION LOADED VERIFY IF THE VERSION IS 5.1.3 OR LOWER ON THE ANDROID PHONE. IF THE ANDROID PHONE WITH MLB.COM AT BAT HAS VERSION 5.1.3 OR LOWER PLEASE RECOMMEND THAT THEY UPDATE THEIR APP TO VERSION 5.2 OR HIGHER AND RETEST FOR THE CUSTOMER SYMPTOM. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

TSB-16-0093

Service Bulletin/Repair Instructions

SOME 2016 F-150, EXPEDITION, NAVIGATOR, TRANSIT, EDGE, FLEX AND EXPLORER VEHICLES EQUIPPED WITH A 3.5L TWIN INDEPENDENT VARIABLE CAM TIMING (TI-VCT) OR A 3.5L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE WITH LESS THAN 3200 KM (2000 MILES) MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0011, P0015, P0016, P0017, P0018, P0019, P0021 AND/OR P0025 STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY.

SSM-45820

Service Bulletin/Repair Instructions

SIRIUS SATELLITE RADIO CHANNEL GUIDE INOPERATIVE

SSM-45821

Service Bulletin/Repair Instructions

SIRI EYES FREE FUNCTIONAL ISSUES USING BLUETOOTH AND APPLE IOS 9.2 AND 9.2.1

SSM-45809

Service Bulletin/Repair Instructions

SYNC 3 ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTCS U3000 OR B108E OR U1A00

TSB160066

Service Bulletin/Repair Instructions

Touchscreen navigation system - arabic language - blank screen

16B10

Service Bulletin/Repair Instructions

In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market

16-0038

Service Bulletin/Repair Instructions

3.5L GTDI - ILLUMINATED MIL - DTC P0011, P0015, P0016, P0017, P0018, P0019, P0021 AND/OR P0025 - UNDER 3200 KM (2000 MILES) Some 2016 F-150, Expedition, Navigator and Transit vehicles equipped with a 3.5L gasoline turbocharged direct injection (GTDI) engine with less than 3200 Km (2000 miles) may exhibit a malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0011, P0015, P0016, P0017, P0018, P0019, P0021 and /or P0025 stored in the powertrain control module (PCM) memory.

TSB160038

Service Bulletin/Repair Instructions

3.5L GKTDI Illuminated MIL - dDTC p0011, p0015, p0016, p0017, p0018, p0019, p0021 And.or p0025 - Under 3200 KM (2000Miles)

LTR3756

Service Bulletin/Repair Instructions

49 CFR Part 579.5 Monthly Communications - January 2016

TSB160001

Service Bulletin/Repair Instructions

49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C

CSC15A03

Service Bulletin/Repair Instructions

Demonstration/Delivery Hold - Application Performance Upgrade 15A03 Certain 2016 Model Year Escape, MKC, Exkpedit;ion, and Navigator Vehicles Sync 3 Software Updates

CSC15B30

Service Bulletin/Repair Instructions

Demonstration /Delivery Hold - Application Performance Upgrade 15B30 Certain 2016 Model Year Escape, MKC, Expedition, and Navigator Vehicles Sync 3 softwasre Updates

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.