Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
TSB 26-2366
Service Bulletin/Repair Instructions
Some vehicles listed in the Model statement above may exhibit a condition where certain devices built on the Android OS platform (including Voxx rear seat entertainment system) indicate they are connected to the vehicles Wi-Fi hotspot, but internet performance is degraded. Symptoms may include no internet access, intermittent connectivity, and/or limited/very low streaming capability. Some websites/apps may partially load while others do not load at all, despite showing Connected. This may be due to the telematics control unit (TCU) software.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 55028
Service Bulletin/Repair Instructions
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
26E04
Emissions
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
TSB 26-2309
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2241. Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
ITRM-26.B04 Expedition
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
SSM 54906
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition vehicles equipped with a 15-inch multi-function display (minor feature code HJGAY) may exhibit an incorrectly sized image displayed on the 360-degree camera after updating the imaging processing module A (IPMA) software and/or replacing the IPMA module. To correct this condition, download and run the "IPMA - Processing Module A (IPMA) 360 View Camera Configuration" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. If the incorrectly sized image displayed on the 360-degree camera is still present, continue with normal diagnostics and repair as necessary outside of this article. Refer to the Workshop Manual, Section 413-13B > Parking Aid - Vehicles With: Parking Aid Camera > Diagnosis and Testing. For claiming, use causal part 14G647 and labor operations 12651D and 12651D4. <br /><br /> To confirm if a vehicle is built with minor feature code HJGAY, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).
SSM 54905
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition equipped with driver's assistance package (minor feature codes DBCBB or DBCBC) may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC) with various invalid data/lost communication diagnostic trouble codes (DTC) stored in the power steering control module (PSCM) and/or anti-lock brake (ABS) module. To correct this condition, download and run the "IPMA - Image Processing Module A (IMPA) Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G647 and labor operation MT14G647SSM up to 1.0 hours. <br /><br /> If the IPMA is failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the FDRS scan tool. Select and run the IPMA Recovery Flash Erase option from the menu. Once communication has been restored with the IPMA, download and run the "IPMA - Image Processing Module (IPMA) Alignment" application in the FDRS and download and run the "IPMA - Image Processing Module A (IPMA) Software
ECG-26.2.11.4.1 Expeditio
Over The Air
Quality improvements include: - Enhanced system performance, disk usage limits and memory monitoring
SYNC-26.2.8.3 Expedition
Over The Air
Quality improvements include: -Privacy robustness updates -Resolves various user interface and data display bugs within the Towing menu
TCU-26.2.11.3 Expedition
Over The Air
Quality improvements include: - Telematics Control Unit update to enhance connected features
TSB 26-2241
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2587. Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
ECG-26.2.11.4 Expedition
Over The Air
Quality improvements include: - Enhanced system performance, disk usage limits and memory monitoring
SSM 54719
Service Bulletin/Repair Instructions
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 25-2587
Service Campaign
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54674
Service Bulletin/Repair Instructions
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
SSM 54605
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles equipped with minor feature codes DBCBB or DBCBC may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store diagnostic trouble codes (DTC) related to invalid data or lost communication. This condition may be due to the software in the image processing module A (IPMA). If the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the Ford Diagnosis and Repair System (FDRS) scan tool. Select and run the IPMA Recovery Flash Erase option from the menu. If the driver assistance warnings and/or symptoms are intermittent, and possibly not failing during the dealership visit, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the FDRS scan tool. Select and run the GWM Ethernet Update option from the menu. If IPMA communication had to be restored using the recovery application, download and run the "IPMA - Image Processing Module (IPMA) Alignment" application
SYNC-25.1.7.10.1 Expedit
Over The Air
25S49 Recall Remedy: -Infotainment software update to address frozen screens
SYNC-25.2.1.6.5.2 Expedi
Over The Air
Quality Improvements Include: - Bug Fixing and Feature improvements. - Resolves black screen issue caused when there is no SiriusXM disk space.
SSM 54534
Service Bulletin/Repair Instructions
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br /> Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 2006D and 2006D45 of the Service Labor Time Standards (SLTS) Man
SSM 54517
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition Timberline vehicles may exhibit a condition where the trail turn assist feature is disabled after a few seconds of activation. This may be due to the accessory protocol interface module (APIM) software. Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via software updates delivered over-the-air (OTA) expected Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by September 2026. Monitor Professional Technician System (PTS) for additional information.
SSM 54503
Service Bulletin/Repair Instructions
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2026 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford Diagnosis and Repair System (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming, use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS) Man
SSM 54447
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles equipped with minor feature codes DBCBB or DBCBC may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store diagnostic trouble codes (DTCs) related to invalid data or lost communication. This condition may be due to the software in the image processing module A (IPMA), disrupting network communication. If the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Select and run the IPMA Recovery Flash Erase option from the apps menu. If the driver assistance warnings and/or symptoms are intermittent, and possibly not failing during the dealership visit, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the FDRS scan tool. Select and run the GWM Ethernet Update option from the apps menu. If IPMA communication had to be restored using the Recovery App, download and run the "IPMA - Image Processing Module (IPMA) Alignm
25L02
Other
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
SSM 54392
Service Bulletin/Repair Instructions
Some 2021-2025 F-150/Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit diagnostic trouble code (DTC) P0299 stored in the powertrain control module (PCM) and may also exhibit a rattle noise from the turbocharger. This may be due to the wastegate actuator rod being disconnected. Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls > Turbocharger has been added to address this condition to allow servicing of the turbocharger actuator rod. In addition, the wastegate actuator rod and associated retention springs and clips have been released as lower level components to complete the repair without replacing the entire turbocharger actuator assembly.
SSM 54363
Service Bulletin/Repair Instructions
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
SSM 54350
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles equipped with driver assistance features and minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication related diagnostic trouble codes (DTCs). The image processing module A (IPMA) should not store these DTCs. This condition may be due to the software in the IPMA, causing it to not communicate on the network. Whether the issue is intermittent or the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. If IPMA communication had to be restored using the Recovery App, download and run the "IPMA - Image Processing Module (IPMA) Alignment" app, recheck DTCs and confirm that all warning messages are cleared from the IPC.<br /><br /> If these steps correct the condition, release the vehicle back to the customer. Advise the customers that a permanent repair to prevent recurrence is expected to be
TSB 25-2512
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 54317
Service Bulletin/Repair Instructions
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS)
SSM 54269
Service Bulletin/Repair Instructions
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
TSB 25-2466
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
PCM-25.6.3 Expedition
Over The Air
Quality improvements include: -On-Board Diagnostics calibration for an enhanced Intake air temperature sensor performance
SSM 54140
Service Bulletin/Repair Instructions
Some 2021-2024 F-150 vehicles equipped with a B&O audio system (minor feature code IDBBQ), and various 2021-2024 Ford and Lincoln vehicles equipped with a B&O audio system may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). This may be due to software in the digital signal processing (DSP) module. To correct this condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.
SSM 54137
Service Bulletin/Repair Instructions
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
SSM 54083
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer, 2022-2023 F-150, and 2023-2024 Expedition/Navigator vehicles equipped with a 2.3L/3.5L EcoBoost engine may exhibit may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9 stored in the powertrain control module (PCM). This may be due to a concern with the turbocharger wastegate. To correct the condition, follow the applicable diagnostic pinpoint tests (PPT) steps found in Workshop Manual (WSM), Section 303-04 and repair as necessary.
SSM 54090
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
TSB 25-2320
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2364 to update the labor times associated with the Service Procedure from M-time to AP-time. Some of the vehicles listed in the Model Statement above, may DTC P2101 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
SSM 53973
Service Bulletin/Repair Instructions
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 53966
Service Bulletin/Repair Instructions
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
SSM 53893
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition vehicles equipped with driver assistance features and minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication related diagnostic trouble codes (DTCs). The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment" app, recheck DTCs and confirm that all warning messages are cleared from the IPC.
SSM 53878
Service Bulletin/Repair Instructions
Some 2021-2025 Expedition/Navigator and 2021-2025 F-150 non-Lightning/non-PowerBoost vehicles may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine to transmission spacer plate (separator plate). To correct this condition, inspect the engine to transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replacement of the torque converter is not necessary. Replace only the engine to transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 > Engine to Transmission Spacer Plate for full spacer plate removal and installation. When reinstalling the starter motor, make sure the starter is flush with the engine to transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine to transmission spacer plate.
SSM 53764
Service Bulletin/Repair Instructions
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 53760
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC. Additionally, some modules may store invalid data/lost communication related DTCs. The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment"
SSM 53661
Service Bulletin/Repair Instructions
Some 2018-2024 Expedition/Navigator vehicles equipped with 22 inch wheels, may exhibit an increased level of vibrations which can be felt while driving on a smooth road at speeds at or above 75 mph (120 km/h). Pinpoint Test G located in Workshop Manual (WSM), Section 204-04 has been developed to assist with diagnosis of this condition. When submitting a warranty claim, include all results from the Pinpoint Test.
SSM 53569
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles may exhibit diagnostic trouble code (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
SSM 53531
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition Timberline vehicles may exhibit a condition where the trail turn assist feature is disabled after a few seconds of activation.
TSB 25-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2251 to update the labor times associated with the Service Procedure from M-time to AP-time.
TSB 25-2107
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2055 to update the labor time description.
SSM 53469
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles may exhibit the liftgate spoiler contacting the roof during freezing temperatures when ice is present.
SSM 53444
Service Bulletin/Repair Instructions
Some 2023-2025 Ford vehicles were not produced with a factory wired keyless entry keypad.
SSM 53419
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC.
TSB 25-2055
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * General system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).
24B59
Other
Certain 2023 Model Year F-150 Super Duty, Expedition, Navigator, and Transit Vehicles Transmission Replacement
OTA SU 10.1.0 Expedition
Over The Air
Quality Improvements: - Customer should be able to enable and disable Intelligent power toggle button. -Adresses SYNC reboots and improves the vehicle's conectivity with the user's phone
SSM 53305
Service Bulletin/Repair Instructions
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
SSM 53301
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition vehicles (not including Expedition MAX) built on or before 26-Jan-2023 may exhibit the liftgate spoiler contacting the roof during freezing temperatures when ice is present.
SSM 53236
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 non-Lightning, 2022-2024 F-150 Lightning/Expedition/Navigator, and 2024 Ranger vehicles may exhibit a "trailer brake module fault" message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) U0137 and/or U0252 stored in the body control module (BCM),
OTA-DSMC-24.5.6 Expeditio
Over The Air
Quality improvements include: -Fixes the Diagnostic Trouble Code that made Bluecruise unavailable for some customers.
24N09
Other
In some of the affected vehicles, customers may initially experience a gear grinding noise from the transmission in reverse, which could progress to illumination of the check engine light and/or transmission wrench light. If the customer continues to operate the vehicle, this could progress to a loss of transmission torque resulting in vehicle speed limitation and inability to shift to reverse.
SSM 53141
Service Bulletin/Repair Instructions
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC
OTA ECG-24.2.5.6.3
Over The Air
Quality improvements include: -Improve battery state of charge drainage issue due to Electronic Control Unit key off load events. -SYNC screen will display correct software update status. -Software update task will be automatically terminated after trigger expiration date
SSM 53088
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
TSB 24-2329
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles built on or before 09-Oct-2024 may experience a random BLIS indicator illuminated in the exterior mirror with no vehicle or objects near the vehicle.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
SSM 53021
Service Bulletin/Repair Instructions
Some 2023-2024 Expedition vehicles equipped with driver assistance features with minor feature code DBCBB and DBCBC may exhibit various driver assistance feature warning messages displayed in the IPC.
SSM 53018
Service Bulletin/Repair Instructions
Some 2021-2024 Ford and Lincoln vehicles may exhibit diagnostic trouble codes (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
ECG-24.2.5.6.1 Expedition
Over The Air
Quality Improvement include: - Addresses potential vehicle no start after OTA update. -SYNC Screen will show correct software update status.
TSB 24-2251
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).
SSM 52610
Service Bulletin/Repair Instructions
Some 2021-2024 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace the engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, make sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine-to-transmission spacer plate.
TSB 24-2180
Service Bulletin/Repair Instructions
This article supersedes 24-2028 to update the vehicle symptom. Some 2022-2024 Expedition/Navigator vehicles may exhibit a random "Blind Spot Not Available Sensor Blocked" and/or "Cross Traffic Alert Not Available Sensor Blocked" warning messages in the IPC with no vehicle or objects near the vehicle. This condition may be intermittent, more noticeable in wet conditions. Diagnostic trouble codes B13F3:97 in the side obstacle detection control module - left (SODL) and/or B13F4:97 in the side obstacle detection control module - right (SODR) and/or U0233 and U0232 in the image processing module A (IPMA) may also be present. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness. To correct the condition, follow the Service Procedure to repair damage and install shields.
TSB 24-2176
Service Bulletin/Repair Instructions
This article supersedes TSBs 24-2100 and 24-2070 to add 2023 F-150 vehicles, update the TSB Issue statement and the TSB Service Procedure. Some 2021-2023 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
SSM 52574
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
TSB 24-2169
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles may experience a random BLIS indicator illuminated in the exterior mirror with no vehicle or objects near the vehicle. This may be due to the radar signal echoing through the trailer hitch bar. To correct the condition, follow the Service Procedure to block the trailer hitch tube ends.
OTATCU24.2.4.8Exp
Over The Air
Quality improvements include: - When pre theft event occurs customers will get notification via Fordpass App. Secondarily, if customer vehicle stolen then call center will be able recieved theft location reports
SSM 52548
Service Bulletin/Repair Instructions
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
24B25
Service Bulletin/Repair Instructions
Certain 2022-2024 Model Year Expedition and Navigator Vehicles - Rear Seat Entertainment Screen Software Update
TSB 24-2135
Service Bulletin/Repair Instructions
Some 2023 Expedition/Navigator vehicles may experience a heated seat indicator center display screen/switch mismatch (Navigator only) or speed assist off switch greyed out (Expedition only). This may be due to the software in the accessory protocol interface module (APIM). To correct the condition, follow the Service Procedure to reprogram the APIM using the latest level of the Ford Diagnosis and Repair System (FDRS) scan tool. The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has been successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
SSM 52483
Service Bulletin/Repair Instructions
Some 2018-2019 Explorer and 2018-2024 Transit/F-150/Expedition/Navigator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.
OTASU6140SYNCEx
Service Bulletin/Repair Instructions
Quality improvements include: -Robustness action to improve the SYNC reboot issue that may occurs after 2 hours of continuous use. -Update BLIS message strategy when a trailer is connected 15 Inch Portrait Implementation
SSM 52445
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles may exhibit intermittent battery drain or no crank/no start concern. The concern may no longer be present after a battery reset. This may be due to the body control module (BCM) software. To correct the condition, reprogram the BCM using the latest version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
OTAPU0630CMRBCDE
Service Bulletin/Repair Instructions
Quality improvements include: Adds robustness to increase the availability of Blue Cruise and fix drop issue.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
TSB 24-2100
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2059 to update the Service Procedure LTIS statement. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
OTAPU0327DSPAMPE
Service Bulletin/Repair Instructions
Quality improvements include: -Fix the hiss or Pop noise from speakers.
23B90
Service Bulletin/Repair Instructions
Customer Satisfaction Program 23B90 Certain 2023 Model Year Expedition Vehicles - Missing Rear Cargo Mat
OTAPU102410CHAUE
Service Bulletin/Repair Instructions
Quality Improvements include: - Fix the no audio out of random speakers issue.
TSB 24-2059
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2351 to remove 2023 F-150 10R80 and 10R80 MHT vehicle applications. The 2023 F-150 10R80 and 10R80 MHT vehicles will be the subject of a separate article. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
TSB 24-2028
Service Bulletin/Repair Instructions
This article supersedes 23-2266 to update the vehicle model years affected to include 2024 model year. Some 2022-2024 Expedition/Navigator vehicles may exhibit a random BLIS warning with no vehicle or objects near the vehicle. This condition may be intermittent, more noticeable in wet conditions. Diagnostic trouble codes B13F3:97 in the side obstacle detection control module - left (SODL) and/or B13F4:97 in the side obstacle detection control module - right (SODR) and/or U0233 and U0232 in the image processing module A (IPMA) may also be present. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness.
SSM 52345
Service Bulletin/Repair Instructions
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
OTAPU0128RBADTEE
Service Bulletin/Repair Instructions
Quality Improvements include: Various dashboard alerts display enhanced such as speed warning and temperature.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52326
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator built on or before 20-Apr-2023 equipped with SYNC 4 may experience SiriusXM® 360L missing one or more of the following features: Channel 700 and above are not accessible, On Demand tab in the SiriusXM® Browse menu is displayed but grayed out/disabled/not functional, SiriusXM® with 360L toggle switch is not displayed in the Connected Vehicle Features menu. This may be due to the gateway module (GWM) configuration. To correct the condition, perform the GWM-Gateway Module A (GWM) Configuration application using Ford Diagnosis and Repair System (FDRS).
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 52317
Service Bulletin/Repair Instructions
2023 F-Super Duty, 2023-2024 Expedition, 2024 Nautilus/F-150 vehicles will exhibit no light emitting diode (LED) confirmation from the key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain a LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.
SSM 52295
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, be sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging newly installed engine-to-transmission spacer plate.
SSM 52269
Service Bulletin/Repair Instructions
2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 52247
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition/Navigator vehicles equipped with a 1 speed transfer case may exhibit a concern where the four-wheel drive (4WD) setting reverts to 2H (two-wheel drive) after a key cycle. This may be due to the transfer case control module (TCCM) software. To correct the condition, reprogram the TCCM using the latest version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7E453 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
OTAPU0630-PFMNFO
Service Bulletin/Repair Instructions
Software Update 23-PU0630-PFM-NFO for 2023 MY EXPEDITION vehicles is now available. Quality Improvements include: - Robustness action to Improve the Master Door Switch Pack loss of functionality.
SSM 52241
Service Bulletin/Repair Instructions
Some 2022-2024 Expedition vehicles equipped with an analog camera and a 12 inch center display screen may exhibit a rear camera image that the customer describes as grainy, fuzzy, or pixelated. This may be due to the interaction between the analog camera and the high definition digital center display screen. To confirm a vehicle is built with an analog camera and a 12 inch center display screen, verify the minor feature codes J3KAR (REAR VIEW CAMERA - LEVEL 2) and HJGAX (MULTI FUNCTION DISPLAY - 12 inch) by reviewing the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This is an operating characteristic of the vehicle. Do not attempt any repairs for this condition.
23B71
Service Bulletin/Repair Instructions
Certain 2023 Model Year F150, Expedition, Navigators equipped with 8.8 inch Front Axles - Front Axle Assembly Replacement
23B62 S1
Service Bulletin/Repair Instructions
Certain 2023 Model Year F-150, Expedition, and Navigator with 3.5L Engine - Engine Long Block Replacement Owner letters submitted 01/02/24
TSB 23-2266
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles may exhibit a random BLIS warning with no vehicle or objects near vehicle. This condition may be intermittent, more noticeable in wet conditions. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness.
SSM 52133
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles equipped with a 1 speed transfer case may exhibit a concern where the 4x4 setting reverts to 2H after a key cycle. This may be due to the transfer case control module (TCCM) software. To correct the condition, reprogram the TCCM using the latest version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7E453 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52134
Service Bulletin/Repair Instructions
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
SSM 52115
Service Bulletin/Repair Instructions
2023 F-Super Duty, 2023-2024 Expedition and 2024 Nautilus vehicles will exhibit no light emitting diode (LED) confirmation from the key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain a LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.
23B65
Service Bulletin/Repair Instructions
Certain 2023 Model Year F-150, Expedition, and Navigator Vehicles equipped with a 3.5L Engine - Right Hand Turbocharger Replacement
TSB 23-2364
Service Bulletin/Repair Instructions
Some 2022-2023 F-150 vehicles equipped with a 3.5L EcoBoost engine built on or after 01-Oct-2022, 2023 F-150 vehicles equipped with a 3.5L PowerBoost engine on or after 01-Oct-2022, and 2023 Expedition/Navigator vehicles built on 01-Dec-2022 and through 30-Apr-2023 may exhibit reduced engine power on startup and an illuminated MIL and/or powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P2101 stored in the powertrain control module (PCM). This may be due to the software level of the PCM. To correct this condition, perform the Service Procedure below to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
SSM 52106
Service Bulletin/Repair Instructions
Some 2023-2024 Expedition/Navigator vehicles equipped with a roof opening panel built on or before 01-Nov-2023 may exhibit a water leak into the vehicle interior from the driver or passenger front corner area of the roof opening panel. This may be due to a kinked or misrouted roof opening panel drain hose. If this condition is present, refer to Workshop Manual, Section 501-17, Pinpoint Test B6 for Navigator or Pinpoint Test C6 for Expedition to check drain hose flow. Make sure the vehicle is parked on level ground. If drain hose flow is normal, continue diagnosis using Pinpoint Test B for Navigator or Pinpoint Test C for Expedition starting at the beginning.
TSB 23-2396
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2036 to add 2024 vehicle model years. Some 2018-2024 Navigator and Expedition vehicles may exhibit a concern where the second row seat back does not fold down or recline when the recline handle is pulled upward or the second row single seat easy entry seat fold switch is pressed. This concern may occur with vehicles equipped with two or three second row seats. This may be due to a broken recliner release lever. To correct this concern, replace the recliner release lever.
23B62
Service Bulletin/Repair Instructions
Certain 2023 Model Year F-150, Expedition, and Navigator with 3.5L Engine - Engine Long Block Replacement
TSB 23-2351
Service Bulletin/Repair Instructions
Some 2021-2023 F-150, 2022-2023 Expedition/Navigator, 2022-2023 Mustang, 2020-2023 Transit, 2020-2023 Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes. stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
TSB 23-2345
Service Bulletin/Repair Instructions
Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial (feet and miles) units and not being able to change to metric (meters and kilometers) units. This may be due to the software level of the SYNC module (APIM). To correct this condition, follow the Service Procedure to update the APIM to the latest software level via a coordinated flash. NOTE: The APIM software update that addresses the symptom listed in this article may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
TSB 23-2353
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer vehicles equipped with a 2.3L EcoBoost engine, 2022-2023 F-150 vehicles equipped with a 3.5L EcoBoost engine, and 2023-2024 Expedition/Navigator vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.
SSM 52044
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition vehicles, built on or before 31-Aug-2023, may exhibit an inoperative approach detection or power door unlock command power running board extended deployment auto timer feature (delayed for 300 seconds without opening the door) when Extended is selected in the center display screen for the power running board AUTO mode. This may be due to various software parameters in the driver front seat module (DSM). To correct the condition, download and run the Driver Front Seat Module (DSM) Configuration app using the latest level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part number 14C708 and applicable labor times from Section 10 of the Service Labor Times Standard (SLTS) Manual.
TSB 23-2320
Service Bulletin/Repair Instructions
This article supersedes 22-2492 to update the vehicle model years affected. Some 2022-2023 Expedition/Navigator vehicles may experience Android Auto/Apple CarPlay connectivity concerns, or center display screen inoperative, frozen or blank. Navigator vehicles with power running boards may randomly not remember the enable/disable setting after a key cycle. This may be due to the software in the SYNC module (APIM). To correct the condition, follow the Service Procedure to reprogram the APIM. The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has been successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
23H05
Service Bulletin/Repair Instructions
Harvest Program 23H05 Certain 2022 Model Year Navigator and 2022-2023 Model Year Mach-E, F150 Lightning, F150, Expedition and Bronco - Instrument Cluster Odometer Inspection
PU0630 RGT-PLO
Service Bulletin/Repair Instructions
Software Update PU0630-RGT-PLO for 2023 Expedition is now available. Quality improvements include: - Robustness action to allow the liftgate to fully open using the exterior button when vehicle is locked.
SSM 51939
Service Bulletin/Repair Instructions
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
SSM 51937
Service Bulletin/Repair Instructions
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SU5P2 Expedition
Service Bulletin/Repair Instructions
Software Update SU5 P2 for 2022 Expedition is now available. Quality improvements include: '- Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing.
SSM 51926
Service Bulletin/Repair Instructions
Some 2021-2023 F-150, 2022-2023 Expedition vehicles equipped with 10 channel audio digital signal processing (DSP) module may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a 10 channel DSP module, verify the minor feature code, F-150 (IDBBQ)/Expedition (IDBAP or IDBBR), by reviewing the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS) website. To correct the condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 18B849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SU4P4 Expedition
Service Bulletin/Repair Instructions
Software Update SU4 P4 for 2023 Expedition Vehicles is now available. Quality improvements include: -Various Apple Carplay quality improvements
SSM 51916
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition Timberline vehicles may experience a clunk noise on turns with the steering wheel turned to full lock. This may be due to steering knuckle to control arm contact. To correct this condition, replace the steering knuckles (service part numbers NL1Z-3K185-D/NL1Z-3K186-D). Refer Workshop Manual, Section 204-01. For claiming, use casual part 3K185 and the applicable labor operations of Section 03 of the Service Labor Time Standards (SLTS) Manual.
SSM 51903
Service Bulletin/Repair Instructions
Some 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
SSM 51901
Service Bulletin/Repair Instructions
Some 2023 Expedition Timberline vehicles may experience a clunk noise on turns with the steering wheel turned to full lock. This may be due to steering knuckle to control arm contact. To correct this condition, replace the steering knuckles (service PN: NL1Z-3K185-D/NL1Z-3K186-D). Refer Workshop Manual, Section 204-01. For claiming, use casual part 3K185 and the applicable labor operations of Section 03 of the Service Labor Time Standards (SLTS) Manual.
SSM 51899
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles may exhibit intermittent no crank/no start concern. The concern may no longer be present after a battery reset. This may be due to the body control module (BCM) software. To correct the condition, reprogram the BCM using the latest version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SU5P1 Expedition
Service Bulletin/Repair Instructions
Software Update 5 P1 for 2022-2023 Expedition Vehicles is now available. Quality improvements include: -Enables rear screen mirroring via vehicle wifi hotspot -Minimize time customer cannot enter the vehicle during future inhibit updates.
TSB 23-2250
Service Bulletin/Repair Instructions
This article supersedes TSB 22-2428 and 23-2176 to update the Issue, Action and Service Procedure. Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
SSM 51838
Service Bulletin/Repair Instructions
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SSM 51827
Service Bulletin/Repair Instructions
Some 2022-2023 F-150 and 2023 Expedition/Navigator vehicles built on or after 01-Oct-2022 equipped with a 3.5L GTDI engine may exhibit reduced engine power on startup and an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P2101 stored in the powertrain control module (PCM). This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers they can remove this condition and continue to drive the vehicle by turning off the vehicle and leaving the vehicle in Key OFF, Engine OFF for at least 30 seconds, then restarting the engine. Engineering is working on a solution that is expected in October 2023. Monitor OASIS for additional information and schedule service appointments once the repair becomes available.
SSM 51789
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles built on or before 13-May-2023 may exhibit the power liftgate not fully opening when the vehicle is locked. This may be due to rear gate trunk module (RGTM) software. To correct this condition, reprogram the RGTM using the latest version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use casual part 14b291 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51776
Service Bulletin/Repair Instructions
Some 2021-2023 Mustang Mach-E/F-150, 2022-2023 Expedition/Navigator and 2023 Corsair vehicles may exhibit a Driver Monitoring Camera Blocked message and/or DTCs B115E:97, B15E1:97 and/or B15E2:97 stored in the driver status monitor camera module (CMR). These DTCs should be disregarded unless it is a DTC with a status byte 8F. Other status bytes should be disregarded as they may be caused by a camera obstruction such as driver position, aftermarket devices or dust on the camera. To clear the DTCs, remove anything obstructing the view of the camera and light emitting diodes (LEDs), place the steering wheel in the center position and close the driver door. Connect Ford Diagnosis and Repair System (FDRS) and clear the DTCs. Turn the ignition off and wait 10 seconds. Turn the ignition on and wait 1 minute. Perform the CMR self-test and reevaluate if DTCs persist.
SSM 51762
Service Bulletin/Repair Instructions
Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial units and not being able to change to metric. This may be due to the software level of the SYNC module (APIM). This issue does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that engineering is currently working on a solution for this condition and will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected in September 2023. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update in September 2023. Monitor OASIS for additional information.
SSM 51713
Service Bulletin/Repair Instructions
Some 2023 Expedition/Navigator vehicles built on or before 13-May-2023 may exhibit the power liftgate not fully opening when commanded and the vehicle is locked. This condition does not affect vehicle durability and no additional diagnosis or service is recommended for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Replacement or reprogramming of the rear gate trunk module (RGTM) is not recommended for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 51715
Service Bulletin/Repair Instructions
2022-2023 Expedition Timberline vehicles may exhibit a clunk noise when the steering wheel is turned to the full lock position. This condition does not affect vehicle durability and no additional diagnosis or service is recommended for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Replacement of the steering knuckle is not recommended for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51687
Service Bulletin/Repair Instructions
TSB 22-2428 is missing some labor operations. For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.
TSB 22-2428
Service Bulletin/Repair Instructions
Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
SSM 51663
Service Bulletin/Repair Instructions
2021-2023 F-150/Expedition may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To correct the condition, reprogram the audio digital signal processing module (DSP) to the latest software level using the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 18B849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51656
Service Bulletin/Repair Instructions
Some 2022-2023 F-150/Bronco/Expedition/Navigator/Escape/Corsair/Bronco Sport/Edge/Mustang vehicles built on 04-Sep-2022 and through 30-Dec-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0230 stored in the powertrain control module (PCM). The vehicle may also experience a no start or stall after start. This may be due to an internal PCM issue. If this DTC is present, verify the battery condition, then perform pin point test (PPT) KC of the Work Shop Manual (WSM), Section 310-01. If PPT KC leads to component replacement, start with replacing the PCM and then evaluate the vehicle. If the DTC returns, follow WSM, Section 310-01 PPT KC direction to address the issue.
SSM 51627
Service Bulletin/Repair Instructions
2023 Expedition vehicles built on or after 02-Jan-2023 are not compatible with previous model year RKE keys and Ford Accessory keyless entry keypads. A different radio frequency is used on 2023 Expedition vehicles built on or after 02-Jan-2023 than previous models. Do not attempt to program previous model year RKE keys or keypads to 2023 Expedition vehicles after 02-Jan-2023.
SSM 51622
Service Bulletin/Repair Instructions
2022-2023 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2023 Expedition/Navigator vehicles built on or after 08-Jun-2022 and 2022 Escape/Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 51601
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 and 2022-2023 F-Super Duty/Expedition/Navigator/Maverick vehicles equipped with an integrated trailer module (iTRM) may exhibit a trailer lamp fault message with various related diagnostic trouble codes (DTC). Most trailer emulator testers will not draw enough current to correctly diagnose these concerns. They may be used to diagnose basic functionality of the iTRM, however, some trailer emulator testers may cause false trailer lamp fault messages to appear. The customer's trailer should be used for diagnosis instead of a trailer emulator tester. Refer to Workshop Manual (WSM), Section 417-01 for normal diagnostics.
SSM 51583
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition/Navigator vehicles equipped with a family entertainment system may experience system concerns. For assistance, contact the VOXX Customer Service Dept. at 1-866-869-7888. If possible, record the device serial number by selecting the gear icon from the home screen, then Settings, scroll to Device and Software, select About, then Your TV and the serial number will be shown on the right-hand side. If the unit will not power up, the serial number is on the label on the back of the monitor. It is also beneficial to know the date the issue occurred, how long the monitors were on prior to the issue, what was being done (streaming video, high-definition multimedia interface (HDMI), what apps) and if the fundamental operating system (FOS) version was recently updated. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
TSB 23-2122
Service Bulletin/Repair Instructions
Some 2021-2023 F-150/Mustang Mach-E and 2023 Expedition/Navigator vehicles equipped with BlueCruise/ActiveGlide may experience loss of BlueCruise/ActiveGlide hands-free driving mode availability and/or BlueCruise/ActiveGlide inoperative and/or diagnostic trouble code (DTC) U2400:00 in the gateway module (GWM) and advanced driver assistance system (ADAS) modules with no other DTCs present. This may be due to an expired BlueCruise/ActiveGlide map file in the GWM and/or the customer's BlueCruise/ActiveGlide map subscription being expired. To correct the condition, follow the Service Procedure to update the GWM.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51531
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer/Aviator/Transit, 2021-2023 F-150/Bronco, 2022-2023 Expedition/Navigator/Mustang and 2023 F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
OTA SU4 P1 Exped
Service Bulletin/Repair Instructions
Software Update 4 P2 for 2023 Model Year Expedition vehicles is now available. Quality improvements include: - Prevents intermittent loss of vehicle connectivity
SSM 51419
Service Bulletin/Repair Instructions
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
SSM 51369
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition vehicles (not including Expedition MAX) built on or before 26-Jan-2023 may exhibit the liftgate spoiler contacting the roof during freezing temperatures when ice is present. This may be due to an insufficient margin between the liftgate spoiler and the roof at the roof center line area. To correct the condition, repair the spoiler and roof per Workshop Manual, Section 501-03/501-28. Make sure that the margin between the liftgate spoiler and the roof is a minimum of 6.5 mm at the roof centerline after liftgate adjustment. For claiming, use causal part 7844210.
SSM 51346
Service Bulletin/Repair Instructions
Some 2022-2023 Expedition vehicles may exhibit the liftgate spoiler contacting the roof during freezing temperatures when ice is present. Engineering is currently investigating this concern. To correct the condition, repair the spoiler and roof per Workshop Manual, Section 501-03/501-28. For claiming, use causal part 7844210.
TSB 23-2036
Service Bulletin/Repair Instructions
Some 2018-2023 Navigator and Expedition vehicles may exhibit a concern where the second row seat back does not fold down or recline when the recline handle is pulled upward or the second row single seat easy entry seat fold switch is pressed. This concern may occur with vehicles equipped with two or three second row seats. This may be due to a broken recliner release lever. To correct this concern, replace the recliner release lever.
SSM 51311
Service Bulletin/Repair Instructions
Some 2018-2023 Expedition/Navigator vehicles may have a concern where the second row seat is locked in the forward tilted position while using Easy Entry preventing rearward movement. To unlock the seat, tip the seat back fully forward and slide the seat fully forward to its end of track travel. This will allow the seat to then be free to move rearward. This operation is characteristic to the Easy Entry feature of the second row seats. Do not force the seat rearward while in the locked position as it can result in damage to the seat track. Refer to the vehicle's Owner's Manual for further details.
SSM 51306
Service Bulletin/Repair Instructions
Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
SSM 51265
Service Bulletin/Repair Instructions
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.