Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
SSM 55069
Service Bulletin/Repair Instructions
Some 2020-2025 Explorer vehicles equipped with a power roof opening panel may exhibit a sunshield with localized bunching or binding/inoperative. This may be due to a broken or missing sunshield fabric retainer/clip. A revised sunshield clip (LJ6Z-5452118-B) is now available to address this condition. It is not necessary to replace the entire sunshield assembly if the clip(s) are broken or missing. Refer to Workshop Manual (WSM), Section 501-17 Roof Opening Panel > General Procedures > Inspection and Replacement of the Roof Opening Panel Shield Clip.
SSM 55060
Service Bulletin/Repair Instructions
Some 2024-2026 Explorer vehicles built on or before 27-Feb-2026 and equipped with the panoramic glass roof may exhibit an uneven gap at the front edge of the roof opening panel shield when fully closed. The gap is an appearance issue only, but may allow outside light to pass through the opening. A new gap hider seal has been released to correct this condition (service part number SB5Z-7851884-A). Adjustment or replacement of the glass, shade or headliner assembly is not necessary. The new seal is installed directly onto the existing vertical flange that is present and visible at the front of the opening when the shade is opened. Once installed, the front edge of the shade will press against the new seal when fully closed. To install, center the seal in the opening with the flexible material facing the power shade and press the seal u-channel over the vertical flange. Explorer vehicles built on or after 27-Feb-2026 have the seal already installed and can be referenced if necessary. Once the seal is installed, perform the shield/shade initialization procedure in Workshop Manual (WSM), Section 501-05 > Gen
SSM55059
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine, 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine, and 2020-2023 Lincoln Aviator vehicles equipped with a 3.0L EcoBoost hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the belt integrated starter generator (BISG). For vehicles with this condition, follow the necessary Pinpoint Test in Workshop Manual (WSM), Section 303-06 for DTC P0A1E and repair the vehicle as directed. Note that previous replacement of the BISG does not negate the need for subsequent BISG replacements if directed to do so by the appropriate Pinpoint Test diagnostics. Engineering is investigating this BISG quality concern. Monitor PTS for updates regarding this investigation.
TSB 26-2349
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2415. Reason for update: To add production build dates of the right-side engine valve cover. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the positive crankcase ventilation (PCV) baffle which is part of the valve cover assembly.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
26E04
Emissions
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
TSB 26-2309
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2241. Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54902
Service Bulletin/Repair Instructions
For 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
TSB 26-2263
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-2210
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM)
SSM 54857
Service Bulletin/Repair Instructions
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
TSB 26-2242
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2213. Reason for update: update the Service Procedure to add notes to clarify the customer symptoms, applicability of this TSB, directing technicians to evaluate both front strut mounts, and add Figure 1 to identify the specific area of the strut mount to observe. Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to the front upper strut mount washer movement under steering loads.
TSB 26-2241
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2587. Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54827
Service Bulletin/Repair Instructions
Some 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles may require replacement of the front drive halfshaft inner/outer CV joint boot for various reasons. If Workshop Manual (WSM), Section 205-04 > Diagnosis and Testing leads to CV joint boot replacement, L1MZ-3A331-G (Explorer/Police Interceptor Utility front inner/outer CV joint boot kit), L1MZ-3A331-H (Aviator front inner/outer CV joint boot kit), L1MZ-3A331-F (Explorer/Police Interceptor Utility front inner CV joint boot kit) and L1MZ-3A331-E (Aviator front inner CV joint boot kit) have been released for service. Refer to WSM, Section 205-04 for Removal and Installation procedures.
25B51
Other
Certain 2021-2024 Model Year Bronco, 2021-2024 Model Year Bronco Sport, 2020-2022 Model Year Corsair and Escape, 2016-2024 Model Year Explorer, 2019-2020 Model Year Fusion, 2016-2018 Model Year Focus RS, 2022-2024 Model Year Maverick, 2016-2019 Model Year MKC and 2019-2024 Model Year Ranger Vehicles Equipped with a 2.0L or 2.3L Engine and Engine Block Heater System Block Heater Replacement
SSM 54809
Service Bulletin/Repair Instructions
Some 20242025 Explorer vehicles built on 01-Feb-2024 and through 31-Jul-2024 may exhibit a rattle/clunk/knock noise from the front suspension at low speeds between 830 mph (1348 km/h) over harsh/uneven pavement such as cracks and small bumps while driving straight (not while turning). This condition may be due to a loose pressure tube within the front strut assembly and may be present in either front strut. In some cases, a louder noise from one strut can mask a lesser noise from the opposite strut, which may result in only one strut being replaced and a repeat visit if the other strut later becomes apparent. When diagnosing, evaluate both front struts for the concern. To repair, replace the affected front strut(s) as necessary. For claiming, use causal part 18124 and labor operation 18124A (one side) or 18124AT (both sides). If the noise persists, refer to Workshop Manual (WSM), Section 204-01 for normal diagnostics.
SSM 54795
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
SSM 54646
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Police Interceptor Utility hybrid vehicles may exhibit a "Refuel Error See Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. If diagnostics in the Workshop Manual (WSM), Section 501-14 Body > Handles, Locks, Latches and Entry Systems > lead to fuel filler door switch replacement, install a new fuel filler door assembly ordered from depot stock to correct this condition. Suspect parts have been cleared from parts depot inventory.
SSM 54783
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test G located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates.
SSM 54774
Service Bulletin/Repair Instructions
Some 2024-2026 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated malfunction indicator (MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. Diagnostic trouble codes (DTC) B3A1B, P0113, P0217, and/or P0480 may be stored in the powertrain control module (PCM). This may be due to poor engine compartment ground connections at G105, G107, G111 and/or G122. Refer to the Wiring Diagram (WD) > Grounds Cell 010 > Pages 2, 3, 7 and 8. Prior to any Workshop Manual (WSM) diagnostics, verify all listed grounds are tightened to 62 lb-in (7 Nm) to resolve this condition. If symptoms or DTCs return after all grounds are tightened, follow normal WSM diagnostics.
SSM 54756
Service Bulletin/Repair Instructions
2021-2026 Explorer vehicles equipped with the 2.3L EcoBoost engine may require air conditioning (A/C) compressor belt removal for various reasons. The Workshop Manual (WSM), Section 303-05A Accessory Drive - 2.3L EcoBoost > Removal and Installation > Air Conditioning (A/C) Compressor Belt procedure has been revised to eliminate cutting the A/C compressor belt to remove it. Refer to the updated procedure to reuse the belt.
SSM 54719
Service Bulletin/Repair Instructions
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 54702
Service Bulletin/Repair Instructions
Some 2020-2023 Aviator and 2020-2024 Explorer/Police Interceptor Utility hybrid vehicles may exhibit a "Refuel Error See Manual" message in the instrument panel cluster (IPC) after installing a replacement fuel filler door assembly (7827936). This may be due to a concern with the replacement fuel filler door assembly. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time.
25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
TSB 25-2587
Service Campaign
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54674
Service Bulletin/Repair Instructions
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
TSB 26-2112
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54655
Service Bulletin/Repair Instructions
Some 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles may exhibit a concern of inoperative, rattling, crackling and/or distorted sound from one or more speakers (but not all speakers). This may be due to other components located near the suspect speaker. Workshop Manual (WSM), Section 415-00 > Diagnosis and Testing > Pinpoint Test D (2020-2024 Explorer/Police Interceptor Utility, 2025-2026 Aviator) and Pinpoint Test E (2020-2024 Aviator, 2025-2026 Explorer/Police Interceptor Utility) have been updated with additional direction when isolating the cause of the condition.
SSM 54614
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer vehicles equipped with a 2.3L engine and 2020-2026 Explorer/Police Interceptor Utility/Aviator vehicles equipped with a 3.0/3.3L engine may require various repairs associated with the fuel tank and/or fuel pump and sender unit. Workshop Manual (WSM), Section 310-00 > Removal and Installation for the fuel tank and fuel pump and sender unit have been revised to eliminate the need to remove the driveshaft as part of the service procedure. Labor times have also been updated to reflect this WSM revision.
TSB 26-2059
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 25-2423. Reason For Update: Replace the incorrect acronym SOWC with the correct acronym OWC. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54589
Other
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various connectivity concerns with The Ford App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.
SSM 54592
Service Bulletin/Repair Instructions
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 54593
Service Bulletin/Repair Instructions
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
SSM 54516
Service Bulletin/Repair Instructions
2020-2026 Police Interceptor Utility vehicles may require level III ballistic panels to be replaced due to broken mounting tabs. Individual level III ballistic panel mounting tab service parts are now available: right-hand (78201B68) and left-hand (78201B69). Replacement of the level III ballistic panel assembly is not required for this condition. Level IV ballistic panels do not have removable mounting tabs and still require complete panel replacement. Level III vs level IV ballistic panels can be identified by a large roman numeral label on the panel or by the vehicle window sticker if equipped.
TSB 25-2614
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit a cupholder base that is damaged or broken. This may be due to the heat stake clips detaching from the cup holder assembly.
SSM 54425
Service Bulletin/Repair Instructions
Some 2020-2026 Police Interceptor Utility hybrid vehicles may exhibit multiple warning messages, various drivability concerns and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P061B stored in the powertrain control module (PCM). This may be due to the incorrect installation of additional police equipment. Equipment should only use the provided rear power access point and must not use the 12V cranking or 12V auxiliary batteries for power. The vehicle will go to sleep after the ignition key is removed and is not designed to power equipment when the vehicle is not running. If equipped, the Police Engine Idle feature can be used to allow the vehicle to securely remain idling and to power equipment. Refer to the Owners Manual.<br /><br /> If it is determined additional equipment has not been added to the 12V cranking or 12V auxiliary batteries, continue with normal Workshop Manual (WSM) diagnostics, Section 303-04C Engine > Fuel Charging and Controls > Diagnosis and Testing > Pinpoint Test QE.<br /><br /> For general upfitter installation guidelines, refer to:<br />
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Customer Script-Expl Hood
Other
2020-2025 MY Explorer hood- customer script
TSB 25-2423
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54202
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer (rear windows only), Bronco Sport, Escape, and Maverick vehicles equipped with minor feature code B2DAC may exhibit an inoperative passenger front and/or rear window switch. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in one of the passenger window switches. To correct the condition, replace the passenger window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.
25H03
Other
Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen
TSB 25-2415
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2361 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
SSM 54137
Service Bulletin/Repair Instructions
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
SSM 54138
Service Bulletin/Repair Instructions
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode
SSM 54116
Service Bulletin/Repair Instructions
Various 2019-2024 Ford and Lincoln vehicles equipped with SYNC 3 may experience a partially or fully black center display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.
TSB 25-2361
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
SSM 54041
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer (rear windows only), Bronco Sport, Escape, and Maverick vehicles equipped with minor feature code B2DAC may exhibit an inoperative passenger front and/or rear window. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle Information or double-clicking the vehicle identification number (VIN) in the upper left corner of Professional Technician System (PTS). This may be due to an open diode in the window switch. To correct the condition, replace the window switch of the affected window. If the condition persists continue with normal diagnostics. Refer to Workshop Manual, Section 501-11. For claiming, use causal part 14529 and labor operation 14529A in the Service Labor Time Standards (SLTS) Manual.
SSM 53973
Service Bulletin/Repair Instructions
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 53982
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer/Aviator, 2020-2025 Police Interceptor Utility, 2020-2022 Escape/Corsair, and 2022-2024 Maverick vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.
TSB 25-2213
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2121 to update the affected production build dates. Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to front upper strut mount washer movement under steering loads.
SSM 53764
Service Bulletin/Repair Instructions
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 53759
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occurring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure in the GWM tool box, not in the toolbox of the module with the DTC's, to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific vehicle identification number (VIN), refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
TSB 25-2188
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an incorrectly illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0420 stored in the powertrain control module (PCM). This may be due to the software in the PCM.
SSM 53638
Service Bulletin/Repair Instructions
After replacement of any TRON module, the gateway module (GWM) and the TRON capable modules can set diagnostic trouble codes (DTCs) U211A, U211B, U211C, U3034, U3035, U3036, U35D9, U35DA and/or U35DB if the secret authentication security keys are not aligned between the modules, a loss of communication is occuring between modules and/or a module is not responding. This may be a result of missing the new module secret authentication security key obtained when running the Ford Diagnosis and Repair System (FDRS) "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure after replacement. When replacing a TRON capable module, run the FDRS "Trusted Real-Time Operation Network (TRON) Module Authentication" procedure to distribute a new set of secret authentication security keys to all TRON-capable modules. Using the specific VIN, refer to Workshop Manual (WSM), Section 418-00 and 418-01 for updated DTCs, applicable TRON module listings and pinpoint tests.
SSM 53601
Service Bulletin/Repair Instructions
Some 2020-2023 Explorer/Aviator, 2020-2025 Police Interceptor Utility, 2020-2025 Escape/Corsair, 2022-2025 Maverick, and 2024-2025 Nautilus vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450:00 stored in the powertrain control module (PCM). This may be due to an evaporative emission system concern or may also be caused by the customer overfilling the fuel tank. If this condition occurs, perform normal diagnosis per Workshop Manual (WSM) Section, 303-13 and repair as necessary. Inform the customer that the condition may have been caused by overfilling of the fuel tank and to not top-off the fuel tank when the fuel pump nozzle automatically shuts off for the first time. Refer the customer to the Fuel and Refueling section of their Owner Manual for additional information.
SSM 53564
Service Bulletin/Repair Instructions
Some 2024-2025 Explorer vehicles built on 01-Feb-2024 and through 31-Jul-2024 may exhibit a rattle/clunk/knock noise from the front suspension at low speeds between 8-30 mph (13-48 km/h) over bumpy or uneven pavement while driving straight.
TSB 25-2121
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit a click/pop noise while turning the steering wheel from straight ahead to full lock during low speed turning events. This noise may be due to front upper strut mount washer movement under steering loads.
SSM 53519
Service Bulletin/Repair Instructions
Some 2020-2025 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may require removal of the left turbocharger oil supply tube due to various concerns.
TSB 25-2112
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0456 stored in the powertrain control module (PCM). This may be due to evaporative emission system concerns and/or the software level of the PCM and has no effect on vehicle operation.
SSM 53336
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer/Aviator vehicles equipped with the 3.0L EcoBoost engine and up to 15,000 miles (24,140 km) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation.
SSM 53305
Service Bulletin/Repair Instructions
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
SSM 53292
Service Bulletin/Repair Instructions
Some 2018-2024 F-150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
SSM 53174
Service Bulletin/Repair Instructions
Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
TSB 24-2331
Service Bulletin/Repair Instructions
Some 2018-2024 F150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
SSM 53070
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer/Aviator vehicles may exhibit an inoperative second row single seat easy entry seat fold switch.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
SSM 52941
Service Bulletin/Repair Instructions
Some 2020-2025 Police Interceptor Utility hybrid vehicles may exhibit multiple warning messages, various driveability concerns and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P061B stored in the powertrain control module (PCM).
SSM 52925
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Aviator/Corsair, 2021-2024 F-150/Bronco, 2023-2024 F-Super Duty, and 2024-2025 Nautilus vehicles may experience the overhead console sunglass bin cannot be locked in a closed position.
SSM 52917
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition.
SSM 52896
Service Bulletin/Repair Instructions
Some 2023-2025 Explorer/Aviator vehicles equipped with the 3.0L EcoBoost engine and up to 15,000 miles (24,140 km) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation.
SSM 52832
Service Bulletin/Repair Instructions
Some 2024-2025 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated malfunction indicator (MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running.
SSM 52820
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off.
SSM 52773
Service Bulletin/Repair Instructions
2023-2024 F-150/Escape/Explorer/Maverick and 2024 Nautilus vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.
SSM 52774
Service Bulletin/Repair Instructions
Some 2020-2024 Escape/Explorer, 2021-2024 F-150, 2022-2024 Maverick and 2024 Nautilus vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger.
SSM 52776
Service Bulletin/Repair Instructions
Some 2020-2025 Explorer/Aviator vehicles may have a concern where the second row outboard manual/power seats do not fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manua
24U06 S1
Service Bulletin/Repair Instructions
Certain 2024 Model Year Bronco Sport, Escape, and Explorer Keyless Entry Remote Control Replacement REASON FOR THIS SUPPLEMENT • Affected Vehicle Build Dates: The build date range for the affected vehicles has been updated to include additional vehicle population. • Technical Instructions: Remote control serial number identification inspection has been updated.
SSM 52722
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
SSM 52704
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
SSM 52675
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
SSM 52652
Service Bulletin/Repair Instructions
On 2020-2024 Explorer/Police Interceptor Utility vehicles, customers may desire modifications that require access to the driver's door ajar circuit. In some cases customers may experience an ajar light on when the driver's door is fully closed. When using pin 13 on the factory 14-way connector to access the driver's door ajar circuit, a 70 mA maximum coil current relay with an integrated clamping diode is required to protect against damage to the door latch. Failure to install this correctly will result in repeat warnings that the driver's door latch/door ajar light will remain on until it is compliant with police modifier's bulletin P-032, which can be found on the Police body builder's site (https://fordbbas.com/publications).
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SSM 52548
Service Bulletin/Repair Instructions
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 52543
Service Bulletin/Repair Instructions
Some 2021-2024 F-150-3.5L FHEV, 2020-2024 Explorer 3.3L FHEV, 2020-2024 Escape 2.5L FHEV, and 2022-2024 Maverick 2.5L FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft® XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics.
SSM 52509
Service Bulletin/Repair Instructions
Some 2023-2024 Police Interceptor Utility vehicles built on 04-Dec-2023 and through 16-Apr-2024 may exhibit a condition where FordPass is inoperative, Fleet Telematics cannot be enrolled and/or the TCU fails provisioning with the parameter identification (PID) for TCU Auth mode reading as Unprovisioned mode. This may be due to incorrect configuration data in the TCU, audio front control module (ACM) and/or accessory protocol interface module (APIM) modules. To correct the condition, download and run the TCU-Telematics Control Unit (TCU) Module Configuration application and the APIM-Accessory Protocol Interface Module (APIM) Configuration application using the latest level of the Ford Diagnosis and Repair System (FDRS) scan tool. If the APIM is not available on the vehicle, then run the configuration applications for the TCU-Telematics Control Unit (TCU) Module Configuration and the ACM-Audio Front Control Module (ACM) Configuration using the latest level of the FDRS scan tool. For claiming, use causal part 14G087 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
24U06
Service Bulletin/Repair Instructions
Certain 2024 Model Year Bronco Sport, Escape, and Explorer - Keyless Entry Remote Control Replacement
SSM 52503
Service Bulletin/Repair Instructions
Some 2023-2024 Explorer/Aviator vehicles equipped with the 3.0L EcoBoost engine and up to 15,000 miles (24,140 km) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation. To correct this condition, replace the fuel injector assemblies (service part L1MZ-9F593-B) for only the respective bank setting the DTC. Refer to Workshop Manual, Section 303-04B. For claiming, use causal part 9F593 and applicable labor standards in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52482
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Aviator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking the fuel pump monitor (VE518) and/or a fuel pump control (VE225) circuits, connector pin push-outs, damaged pins/terminals, and/or loose/corroded grounds. Inspect FPCM connector C433/C4033, ground G407, and inline connections C1147 and C3136 for being fully seated and damage free prior to performing guided diagnostics or replacing any components.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52390
Service Bulletin/Repair Instructions
Some 2023-2024 Explorer vehicles built on or after 31-Jul-2023 (minor feature code J3KAJ which can be confirmed by double-clicking the VIN on PTS in the upper left corner) are no longer equipped with the 360 degree view camera or reverse brake assist features. Vehicles affected are equipped with only rear functioning cameras. The vehicle is not misbuilt. Do not submit a claim for this condition. Affected vehicles of this change can be verified by entering a vehicle identification number (VIN) on Professional Technician System (PTS) to check for a 360-degree camera credit on the window sticker. Diagnosis and repair for any parking aid concerns on these vehicles should follow Workshop Manual (WSM) Section 413-13B for Rear Parking Aid Camera System only. Do not use the 360 degree view camera or reverse brake assist diagnostics or repair procedures.
SSM 52351
Service Bulletin/Repair Instructions
Certain 2023-2024 Explorer vehicle trim levels built on or after 6-Feb-2023 are no longer equipped with the rear heating ventilation and air conditioning (HVAC) control panel on the rear of the center console. The following Explorer trim levels no longer include the rear HVAC control panel: Base, XLT 200A, XLT 202A without the Sport Appearance Package (sales code: 68M). Customers can adjust the rear climate control system via the front HVAC control panel. Installation of a rear HVAC control panel is not warrantable.
SSM 52348
Service Bulletin/Repair Instructions
2024 Explorer/Aviator vehicle key fobs are shipped from the factory zip tied together. If the vehicle does not come with the key fob pairs zip tied together at transport delivery to the dealership, validate that both key fobs work. If both key fobs do not work or if only one key fob is present when vehicle is recieved at transport delivery to the dealership, a claim must be made using the Delivery App, or delivery receipt/ePOD process. This is not a warrantable item as per the warranty policy manual section 2.1.00. Note that zip tied key fobs might not allow the Passive Entry feature to function correctly.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
TSB 24-2043
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2208 to add 2024 model year vehicles. Some 2020-2024 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern
TSB 24-2044
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2181 to add 2024 vehicle model year. Some 2020-2024 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.
SSM 52269
Service Bulletin/Repair Instructions
2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 52189
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Aviator vehicles may exhibit poor speaker sound quality and/or tick-tock noise while activating turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the accessory protocol interface module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.
SANVol 2 Issue 1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.