Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB 26-2406
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the powertrain control module (PCM)/transmission control module (TCM) This may be due to sticking valves in the main control valve body and/or damaged E clutch friction plates and/or E clutch steel plates. Additional model information: 6.7L Diesel Engine 7.3L Gas Engine 10R140 Automatic Transmission
SSM 55116
Service Bulletin/Repair Instructions
Some of the following vehicles: * 2025-2026 Expedition/Navigator built on or after 02-Feb-2025 * 2025-2026 F-Super Duty built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 55021
Service Bulletin/Repair Instructions
Some 2025-2026 Bronco/Bronco Sport/Corsair/F-150/F-Super Duty/Maverick/Mustang/Mustang Mach-E/Ranger vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 10654C, 12651D and 12651D4.
SSM 54975
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12650D, 12650D45, and 12650D81.
SSM 54979
Service Bulletin/Repair Instructions
Some 2023-2025 Mustang Mach-E and 2024-2026 F-Super Duty vehicles equipped with a 360-degree camera may exhibit a distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q3 of 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SSM 54900
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12651D, 12651D45, and 12651D80.
TSB 26-2263
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
PDM-26.21.5 SuperDuty
Over The Air
Quality improvements include: -Prevents window bounce backs after using the one touch up feature
RCM-26.4.2.1 SuperDuty
Over The Air
Quality improvements include: -Updates the Restraint Control Module to prevent a potential internal fault that may cause a warning light to illuminate for one key cycle
TSB 26-2185
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
ECM-26.10.0 SuperDuty
Over The Air
26E01 Recall remedy -Powertrain Control Module calibration update to ensure emissions system restrictions function properly when the vehicle is parked.
SSM 54765
Service Bulletin/Repair Instructions
Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
SSM 54763
Service Bulletin/Repair Instructions
Some 2025-2026 F-Super Duty vehicles built without lane departure warning (built with minor feature code HLEAA) and 2025-2026 Expedition/Navigator vehicles built on or before 26-Mar-2026 may exhibit a clicking or creaking type noise when turning the steering wheel during low-speed maneuvers. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). If a vehicle exhibits this condition, use a chassis ears tool and place the microphone clamp on or near the universal joint yoke of the steering column upper shaft (below the column). Turn the steering wheel with the vehicle stationary to replicate the concern. If the same noise is clearly heard through the chassis ears at this location, replace the steering column upper shaft (base part number 3E751). Refer to Workshop Manual (WSM), Section 211-04. For claiming, use causal part 3E751 and service labor operations 3676AUP and 1006D.
SSM 54730
Service Bulletin/Repair Instructions
2026 F-Super Duty vehicles equipped with a floor console and a media bin door no longer activate the door with spring assist (push-push). The media bin is now manually opened and closed (push-pull) operation. Do not attempt to repair or submit a warranty claim for this condition.
ITRM-26.BG.FG SuperDuty
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
SSM 54722
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles equipped with a trailer brake control module may exhibit a "Trailer Disconnected" message after cycling the ignition off and back on with a trailer connected. This may be due to the presence of an integrated battery charger on a trailer equipped with electric over hydraulic brakes. If trailer functionality is restored after unplugging and plugging the trailer connector back in while the ignition is on, this condition can be corrected by downloading and performing the "Trailer Brake Configuration" application using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 19H332 and labor operations 12651D and 12651D4. Workshop Manual (WSM), Section 417-01 Exterior Lighting > Diagnosis and Testing > Trailer Lamps > Pinpoint Test G has been updated to improve diagnostics for this condition.
DDM-26.21.5 SD
Over The Air
Quality improvements include: -Prevents window bounce backs after using the one touch up feature
SSM 54648
Service Bulletin/Repair Instructions
Some 2024-2026 F-150/F-Super Duty vehicles may exhibit an inoperative front passenger window when operated from the driver master window control switch with diagnostic trouble code (DTC) U2013:23 stored in the driver door module (DDM). This may be due to the software in the DDM and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operations 12651D and 12651D4.
26E01
Other
Certain 2023 - 2026 Model Year F-250 – F600 Super Duty Vehicles with 6.7L Engines Powertrain Control Module (PCM) Software Update The affected vehicles were originally manufactured with Powertrain Control Module (PCM) software that did not provide the correct warnings when certain conditions are present in the Selective Catalyst Reduction (SCR) system as required and described in the Owner’s Manual.
SSM 54641
Service Bulletin/Repair Instructions
Some 2025-2026 F-Super Duty vehicles properly upfitted with a snowplow kit following the guidelines in the Super Duty Body Builders Layout Book (located on the www.FordPro.com website > Resources > Body Builder Advisory Service (BBAS) > Publications) may experience a radio volume that temporarily turns off or decreases when the engine RPMs are raised above idle and the snowplow is operated. Ford is aware of this condition and is investigating a service solution. Component replacement is not expected to resolve this condition. Monitor Professional Technician System (PTS) for updates.
SYNC-26.2.4.10 SD
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54594
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles may exhibit rain sensitive wipers (if equipped) settings that do not change when selected in the center touch screen. Vehicles may also exhibit an inoperative heated steering wheel (if equipped) after a remote start event. This may be due to the software in the steering column control module (SCCM). To correct the condition, reprogram the SCCM using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 3F791 and labor operations 12651D and 12651D4.
SSM 54587
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles may exhibit rain sensitive wipers (if equipped) settings that do not change when selected in the center touch screen. Vehicles may also exhibit an inoperative heated steering wheel (if equipped) after a remote start event. This may be due to the software in the steering column control module (SCCM). To correct the condition, reprogram the SCCM using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 3F791 and labor operation 12651D.
SSM 54592
Service Bulletin/Repair Instructions
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 54584
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles that require replacement of the heating ventilation and air conditioning (HVAC) module may have previously experienced a PMI that will not complete during installation. This may be due to a concern with the PMI application within the Ford Diagnosis and Repair System (FDRS) scan tool. To correct this condition, navigate to the FDRS application HVAC Programmable Module Installation (PMI). Click on the download button (if not already downloaded) or the refresh button on the right side of the application (if the application is already downloaded). Hover your mouse over the application name and verify the application version reads G2327867-5.0 or higher. Once the application is confirmed to be updated, run the HVAC PMI application.
SSM 54585
Service Bulletin/Repair Instructions
Some 2021-2026 F-150 and 2024-2026 F-Super Duty vehicles equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /> <br /> For vehicles included in Field Service Action (FSA) 25P35 and/or 26P02, perform repairs as directed by the FSA(s).<br /> <br /> For 2021-2026 vehicles not included in the FSA(s), reprogram the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool according to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and testing direction by symptom. For claiming, use causal part 14B291 and labor operation MT14B291SSM, up to 0.4 hours.
SSM 54564
Service Bulletin/Repair Instructions
Some 2021-2026 F-150 and 2024-2026 F-Super Duty vehicles equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /> <br /> For vehicles included in Field Service Action (FSA) 25P35 and/or 26P02, perform repairs as directed by the FSA(s).<br /> <br /> For 2021-2026 vehicles not included in the FSA(s), reprogram the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool according to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and testing direction by symptom. For claiming, use causal part 14B291 and labor operation MT14B291SSM.
26P02
Other
Certain 2025-2026 Model Year F-150 and F-250-600 vehicles Driver Door Module (DDM) & Passenger Door Module (PDM) Software Updat
SSM 54559
Service Bulletin/Repair Instructions
Some 2026 F-Super Duty and F-650/F-750 vehicles equipped with a 10R140 automatic transmission may exhibit fluid leakage from the transmission fluid pan area. Prior to performing any repairs, thoroughly clean the transmission fluid pan area to ensure accurate identification of the leak source. Before replacing the transmission fluid pan or gasket, verify the torque of the fluid pan bolts and stud bolts. If the torque is incorrect, tighten the pan bolts and stud bolts to the specified torque following the proper torque sequence in Workshop Manual (WSM), Section 307-01. After tightening, verify that the leak has been repaired. If the pan bolts and stud bolts are already torqued correctly, proceed with standard leak diagnosis. Should the diagnosis indicate that pan replacement is required, mark the area of the pan where the leak is present. This information will assist engineering with root cause analysis. For claiming, use causal part 7A194 and labor operation 7000E.
SSM 54546
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty and 2024-2026 F-150 vehicles were not produced with a factory wired keyless entry keypad. If the customer desires to install a Ford Accessory wireless keyless entry keypad, the radio transceiver module (RTM) in these vehicles operates on a different frequency than previous models. The correct part number for the keyless entry keypad is SK4Z-14A626-A. A wired keyless entry keypad cannot be added to a 2025-2026 F-Super Duty/F-150 vehicle that was not originally produced with it. Refer to Professional Technician System (PTS) > Workshop > Accessories > Installation > Electrical for further instruction.
SSM 54507
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls and/or bouncing back when using the one-touch close function.<br /><br /> For vehicles effected by Field Service Action (FSA) 25P35, perform repairs as directed by the FSA.<br /><br /> For 2021-2026 vehicles, update the driver door module (DDM) and the passenger door module (PDM) using the latest software level of Ford Diagnosis and Repair System (FDRS) scan tool. Refer to the Workshop Manual (WSM), Section 501-11 for normal diagnostics and repair direction by symptom. For claiming, use causal part 14B291 and service labor operations 12651D and 12651D4.
SSM 54503
Service Bulletin/Repair Instructions
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2026 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford Diagnosis and Repair System (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming, use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS) Man
SSM 54493
Service Bulletin/Repair Instructions
Some 2023-2025 Mustang Mach-E and 2024-2026 F-Super Duty vehicles equipped with a 360 degree camera may exhibit a distorted or blurry 360 degree camera image in the center display screen, but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q2 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
25B63
Other
Certain 2025 Model Year Expedition and 2026 Model Year F-250-F-600 Super Duty Vehicles - Transmission Main Control Valve Body Replacement
25P35
Other
Certain 2025-2026 Model Year F150, F250-F600 Vehicles. Front Door Lower Window Glass Run Replacement
SSM 54448
Service Bulletin/Repair Instructions
Some 2017-2026 F-Super Duty vehicles may exhibit a pull/drift condition during braking. This may be due to the brake pads needing to be broken in. Repeated, heavy brake applications may assist to resolve the pull/drift condition. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information.
SSM 54420
Service Bulletin/Repair Instructions
Some 2023-2026 F-Super Duty vehicles built on or before 01-Oct-2025 may exhibit a "Hill Start Assist Unavailable" and/or "Parking Brake Limited Function" message at vehicle start-up with diagnostic trouble codes (DTCs) U0151, U023A, U0159 and/or U0146 stored in the anti-lock brake system (ABS) module. These DTCs and/or U0415 may also be present in various other modules related to "invalid data received from the ABS control module". This may be due to the software in the ABS module. To correct the condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 2C219 and labor operations 2219D and 2219D44.
SSM 54326
Service Bulletin/Repair Instructions
Some 2018-2025 F-150 and 2018-2026 F-Super Duty vehicles equipped with a tailgate step may exhibit a step assembly that binds/will not open or opens/pops up while driving. This could be due to an incorrect adjustment of the tailgate step assembly. Before replacing any components for this concern, follow the revised Tailgate Step Adjustment procedure in Workshop Manual (WSM), Section 501-04.
SSM 54311
Service Bulletin/Repair Instructions
2023-2026 F-Super Duty vehicles may be equipped from the factory with a power steering system filled with Motorcraft® MERCON® LV Automatic Transmission Fluid XT-10-QLVC or XL-22 high temperature power steering fluid that looks like clear hydraulic fluid. Both fluids are interchangeable in the power steering system when service is required. Workshop Manual, Section 211-02 > Power Steering > Specifications has been updated to provide the correct power steering fluid usage.
SSM 54218
Service Bulletin/Repair Instructions
Some 2025-2026 F-Super Duty vehicles built on 10-Jun-2025 and through 11-Aug-2025 may exhibit the passenger side register not blowing cold air when commanded. This may be due to the heating, ventilation and air conditioning (HVAC) module calibration of the actuator. Download and run the "HVAC - Climate Control System Actuators Calibration" application with the Ford Diagnosis and Repair System (FDRS) and retest. If the concern remains, refer to the Workshop Manual (WSM), Section 412-00 for normal diagnostics. For claiming use causal part 19980 and labor operations 12651D and 12651D4. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
SSM 54215
Service Bulletin/Repair Instructions
Some 2019-2026 F-Super Duty vehicles equipped with a 6.7L engine may require various repairs and/or maintenance to the fuel system where quick release couplings are utilized, such as the secondary fuel filter. The Workshop Manual (WSM), Section 310-00 > General Procedures > Quick Release Coupling has been updated to include videos and instructions of proper disconnect/connect steps involving the Type 27 quick release couplings.
SSM 54180
Service Bulletin/Repair Instructions
Some 2026 F-Super Duty vehicles may require retrieval of the factory keycode for factory installed wired keyless entry keypads. If Ford Diagnosis and Repair System (FDRS) scan tool retrieval is not available, the code can be retrieved using 2 programmed keys. Perform the following steps within 10 seconds. Place the first programmed key into the ignition lock cylinder or backup starting location and turn the ignition on. Turn the ignition off and remove the first programmed key. Place the second programmed key into the ignition lock cylinder or backup location and turn the ignition on. The factory keycode displays momentarily in the instrument panel cluster message center. Do not submit a warranty claim for this procedure. This procedure is in Workshop Manual (WSM), Section 501-14 > Description and Operation.
SSM 54182
Service Bulletin/Repair Instructions
2026 F-Super Duty vehicles equipped with a floor console and a media bin door no longer activate the door with spring assist. It is manually opened and closed. Do not attempt to repair or submit a warranty claim for this condition.