Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
17B29-S2
Service Bulletin/Repair Instructions
Certain 2016-2017 Model Year F-650, F-750 and F-59 Vehicles with a 6.8L Engine - Cylinder Head Inspection and Replacement
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47823
Service Bulletin/Repair Instructions
Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
17B30-S2
Service Bulletin/Repair Instructions
Certain 2012-2016 Model Year F-450 ? F-750 and F-59 Commercial Stripped Chassis Vehicles Equipped with a 6.8L Engine Camshaft Roller Follower Replacement Coverage
SSM 47009
Service Bulletin/Repair Instructions
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
17B29
Service Bulletin/Repair Instructions
Certain 2016-2017 Model Year F-650, F-750 and F-59 Vehicles with a 6.8L Engine - Cylinder Head Inspection and Replacement
SSM 46900
Service Bulletin/Repair Instructions
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46451
Service Bulletin/Repair Instructions
2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
SSM 46153
Service Bulletin/Repair Instructions
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
TSB16-0106
Service Bulletin/Repair Instructions
SOME 2016-2017 F-53 MOTORHOME CHASSIS AND F-59 COMMERCIAL STRIPPED CHASSIS VEHICLES EQUIPPED WITH A 6.8L ENGINE AND BUILT ON OR BEFORE 6/20/2016 MAY EXHIBIT A NO TRANSMISSION DOWNSHIFT WHEN DESCENDING A GRADE IN TOW/HAUL MODE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 45876
Service Bulletin/Repair Instructions
2016-2017 F-53/F-59 - 6.8L ENGINE WITH GVWR 14,001 LB AND THROUGH 19,500 LB - NO TRANSMISSION DOWNSHIFT ON DOWNHILL IN TOW HAUL MODE
16B10
Service Bulletin/Repair Instructions
In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
16-0042
Service Bulletin/Repair Instructions
6.8L - HYDROMAX® INSTRUMENT CLUSTER ICON ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE (DTC) C149D - BUILT ON OR BEFORE 3/2/2016 ISSUE Some 2016 F-53 Motorhome Chassis and F-59 Commercial Stripped Chassis vehicles equipped with a 6.8L engine and built on or before 3/2/2016 may exhibit Hydromax® instrument cluster icon illuminated with DTC C149D present in the anti-lock brake system (ABS) module memory. SERVICE PROCEDURE 1. Using Integrated Diagnostic System (IDS) or equivalent, retrieve DTCs from the ABS module. Is DTC C149D present in the ABS module memory? a. Yes - proceed to Step 2. b. No - this article does not apply. Refer to Powertrain Control/Emission Diagnosis (PC/ED) manual for normal diagnostics. 2. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 99.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. 3. Clear DTCs.
TSB160042
Service Bulletin/Repair Instructions
6.8L - Hydromax instrument cluster icoin illuminated with diagnostic trouble code (DTC) C149D Built on or before 03/02/2016
16-0037
Service Bulletin/Repair Instructions
6.8L - ILLUMINATED MIL - VARIOUS DTCS - BUILT ON OR BEFORE 2/15/2016 ISSUE Some 2016 F-53 Motorhome Chassis and F-59 Commercial Stripped Chassis vehicles built on or before 2/15/2016 and equipped with a 6.8L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0309 and/or P0310 present in powertrain control module (PCM) memory with no other drivability symptoms.
TSB160037
Service Bulletin/Repair Instructions
6.8L Illuminated MIL - various DTCS - Built on or before 02/15/2016
15-0158
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-45239
Service Bulletin/Repair Instructions
FORD: SOME VEHICLES TRANSMISSION WILL EXPERIENCE, AFTER A COLD SOAK OR AN EXTENDED PERIOD WITH ENGINE OFF, A 2-3 SHIFT HESITATION DUE TO POSSIBLE HYDRAULIC CIRCUIT DRAIN. MODEL 2013-16 VARIOUS VEHICLES. *PE