25E09
Emissions
NEW VEHICLE DEMONSTRATION / DELIVERY HOLD Emissions Recall 25E09 Certain 2022 Model Year F-250 - F-600 Vehicles with 6.7L Engines Powertrain Control Module Programming and Particulate Matter Sensor Installation
Vehicle report
2022 FORD F-600 SD
Service bulletins
50 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
25N14
Other
Certain 2022 Model Year F-250 - F-600 with 6.7L Diesel Engines One-Time Replacement for Diesel Particulate Filter Assembly Failures, If Required After Dealer Evaluation
25N10S1
Other
Certain 2017-2025 F-450 – F-600 Chassis Cab Upfitted with an Aerial Bucket Frame Rail Crack
25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
25N10
Other
Certain 2017-2025 F-450 – F-600 Super Duty Chassis Cab Upfitted with an Aerial Bucket Frame Rail Crack
TSB 26-2050
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2142 to update the Parts List, Service Procedure (Steps 1-2), and increase the labor operation allowances to reprogram the PCM/TCM. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km)
TSB 24-2249
Service Bulletin/Repair Instructions
This article supersedes TSB 22-2087 to update the Part List. Some 2020-2022 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit harsh reverse to drive engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and if necessary, replace the input shaft seals (F9) and the output shaft seals (F10).
SSM 52595
Service Bulletin/Repair Instructions
When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
TSB 24-2142
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SSM 52574
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
SSM 52548
Service Bulletin/Repair Instructions
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52467
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08 and/or B1D09 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Disconnect connector C4099 from the back of the trailer tow connector (14489). Inspect connector C4099 and the mating socket on the back of the trailer tow connector for signs of corrosion or damage. If corrosion or damage is present at either connector, replace both the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 13A576 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 52411
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles built on or after 01-Oct-2022 may exhibit the power running boards settings intermittently changing from AUTO to OFF without any driver input. This may be due to the software in the running board control module (RBM). To correct the condition, reprogram the RBM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14C177 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52389
Service Bulletin/Repair Instructions
Some 2022-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) U3012 stored in the PCM. If no drivability concerns or other DTCs are present, perform normal diagnostics per the Workshop Manual (WSM). If diagnostics lead to the powertrain control module (PCM) or body control module (BCM), the replacement of the PCM and/or the BCM will not resolve this concern. This illuminated MIL with DTC U3012 does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 52345
Service Bulletin/Repair Instructions
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 52307
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52308
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08:11 and/or B1D09:11 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Inspect connector C4099 and the trailer tow connector (14489) for signs of corrosion or damage. If corrosion or damage is present at either connector, replace the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 14489 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
SSM 52188
Service Bulletin/Repair Instructions
2024 F-Super Duty vehicles are equipped with XL-22 (WSS-M2C184-A1) high temperature power steering fluid that looks like clear hydraulic fluid. This fluid is an improvement in high temperature and thermal oxidative stability compared to Mercon LV. This power steering fluid is also compatible and highly recommended to use when filling or topping off power steering systems of all 2012-2023 F-Super Duty vehicles originally equipped with Mercon LV.
SSM 52134
Service Bulletin/Repair Instructions
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
TSB 23-2376
Service Bulletin/Repair Instructions
Some 2022 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
SSM 52098
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may require a long block replacement of the engine for various reasons. The replacement long block may be equipped with an updated upper oil pan. If the oil filter adapter from the original engine does not mate with the new upper oil pan, service parts PC3Z-6881-A (oil filter adapter), W503277-S439 (package of 6 bolts, 4 bolts required), W718564-S450 (stud), W520101-S442 (nut), and PC3Z-14A206-A (starter cable retaining bracket) will be needed to complete the repair.
23B24
Service Bulletin/Repair Instructions
Customer Satisfaction Program 23B24 Certain 2022 Super Duty and 2023 F-Series Models with Tailgate Step - Inspection of Tailgate Step Handle and Replacement
22L03
Service Bulletin/Repair Instructions
Certain 2021-2022 Model Year Econoline, Super Duty Chassis Cab, F53 Motor Home, F59 Step Van, and F650/F750 Medium Duty Chassis Cab Vehicles Equipped with a Premium Rated 7.3L Engine - Engine Horsepower Credit
22N05 S1
Service Bulletin/Repair Instructions
Certain 2022 Model Year Super Duty 6.7L Diesel Engine - One-Time Replacement for Diesel Particulate Filter Assembly Failures Supplement 1
SU4 P1 SuperDuty
Service Bulletin/Repair Instructions
Software Update 4 P1 for 2022 Super Duty vehicles is now available. Quality improvements include: - Minimize time customer cannot enter the vehicle during future inhibit updates.
SSM 51762
Service Bulletin/Repair Instructions
Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial units and not being able to change to metric. This may be due to the software level of the SYNC module (APIM). This issue does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that engineering is currently working on a solution for this condition and will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected in September 2023. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update in September 2023. Monitor OASIS for additional information.
SSM 51741
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles may exhibit inoperative heated/ventilated front seats during a remote start event. This may be due to the software in the driver seat module (DSM). To correct the condition, reprogram the DSM using the latest software version of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51725
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51719
Service Bulletin/Repair Instructions
Some 2021-2023 F-Super Duty/E-Series vehicles equipped with a 6.2L, 6.8L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 and/or P0455 stored in the powertrain control module (PCM). This may be due to a improper fuel filler cap installation and/or outside contamination on the fuel cap sealing surface. The fuel filler cap requires multiple turns to seal properly and should be clean of any debris on sealing surface. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. If the DTCs return after the fuel filler cap is cleared of debris and properly seated, refer to Workshop Manual (WSM), Section 303-13 > pinpoint test HX.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51691
Service Bulletin/Repair Instructions
2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
TSB 23-2161
Service Bulletin/Repair Instructions
Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
SSM 51652
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 (MBG-2022-174N in Canada) and monitor OASIS for updates.
SSM 51649
Service Bulletin/Repair Instructions
Some 2021-2023 F-Super Duty vehicles equipped with a 10R140 transmission may exhibit harsh or delayed engagement/shift concerns. Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual, Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive learning drive cycle before attempting internal service. Although this routine was developed for low mileage vehicles, it has proven effective for resolving many shift and engagement symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards Manual.
SSM 51648
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may experience a lack of power due to snow packing of the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22ÃÂðF (-30ÃÂðC). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10ÃÂðF (-12ÃÂðC) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.
SSM 51629
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 and monitor OASIS for updates.
SSM 51601
Service Bulletin/Repair Instructions
Some 2021-2023 F-150 and 2022-2023 F-Super Duty/Expedition/Navigator/Maverick vehicles equipped with an integrated trailer module (iTRM) may exhibit a trailer lamp fault message with various related diagnostic trouble codes (DTC). Most trailer emulator testers will not draw enough current to correctly diagnose these concerns. They may be used to diagnose basic functionality of the iTRM, however, some trailer emulator testers may cause false trailer lamp fault messages to appear. The customer's trailer should be used for diagnosis instead of a trailer emulator tester. Refer to Workshop Manual (WSM), Section 417-01 for normal diagnostics.
TSB 23-2133
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the engine will not turn off and/or have various electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure to inspect for water/moisture intrusion into the BJB and replace the BJB and cover if water/moisture intrusion is found.
SSM 51558
Service Bulletin/Repair Instructions
Some 2022 F-Super Duty vehicles equipped with auto fold exterior mirrors may exhibit an inoperative/grayed out Auto Fold selection in the mirror settings menu in the instrument panel cluster (IPC). This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-2115
Service Bulletin/Repair Instructions
Some 2015-2020 F-150 and 2017-2022 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
21M05-S1
Service Bulletin/Repair Instructions
Certain 2017-2022 Model Year Super Duty Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening. In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford had developed an enhanced remedy for customers who may want this enhanced repair performed n their vehicle.
22G03
Service Bulletin/Repair Instructions
Certain 2022 Model Year Super Duty Vehicles with Star White Tri Coat Premium Paint - Repaint Exterior Components to Match Body Color. All of the affected vehicles were built with an incorrect paint mixture. The amount of mica flake (sparkles) became diluted creating poor visual harmony between body and attached hang-on parts such as door handles, mirror caps, ets... The level of mica will vary between vehicles.
SSM 50830
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 7.3L engine and built on or before 11-May-2022 may exhibit a ticking/clicking/tapping noise at idle that is loudest at the front of the engine where the front timing cover meets the oil pan. This may be due to a cracked oil pump drive gear. If the noise originates from the lower front of the engine, remove the accessory drive belt and retest. If the noise is still present, remove the oil pan and rotate the crankshaft 360 degrees to inspect for cracking. If cracked, replace the oil pump drive gear (LC3Z-6306-A).
SSM 50742
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 for the ambient air temperature sensor stored in the powertrain control (PCM). When performing pinpoint test BF in Workshop Manual (WSM), Section 413-01, the ambient air temperature sensor/outside air temperature display reset procedure has been added to the Ford Diagnostic Repair System (FDRS) diagnostic scan tool. Depending on how the vehicle is equipped, run the FCIM or HVAC. Reset the Outside Air Temperature Sensor Learned Values application. Clear DTCs and retest after performing the reset procedure.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.