Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB 24-2249
Service Bulletin/Repair Instructions
This article supersedes TSB 22-2087 to update the Part List. Some 2020-2022 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit harsh reverse to drive engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and if necessary, replace the input shaft seals (F9) and the output shaft seals (F10).
SSM 52595
Service Bulletin/Repair Instructions
When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SSM 52548
Service Bulletin/Repair Instructions
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
22M03 S1
Service Bulletin/Repair Instructions
Certain 2017-2020 Model Year Continental and Super Duty, 2018-2020 Navigator, 2020 Aviator, and 2020 Explorer Vehicles Replace Front and/or Side Cameras if Foggy
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
22N15
Service Bulletin/Repair Instructions
Customer Satisfaction Program 22N15 Certain 2020-2023 Model Year Bronco Sport, Escape, Corsair, E-Series, F-650/F-750, F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Adding Not OTA Capable Owner letters. Other documents submitted 01/02/24 & Received OTA letters submitted on 02/01/24
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 52307
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52188
Service Bulletin/Repair Instructions
2024 F-Super Duty vehicles are equipped with XL-22 (WSS-M2C184-A1) high temperature power steering fluid that looks like clear hydraulic fluid. This fluid is an improvement in high temperature and thermal oxidative stability compared to Mercon LV. This power steering fluid is also compatible and highly recommended to use when filling or topping off power steering systems of all 2012-2023 F-Super Duty vehicles originally equipped with Mercon LV.
SSM 52098
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may require a long block replacement of the engine for various reasons. The replacement long block may be equipped with an updated upper oil pan. If the oil filter adapter from the original engine does not mate with the new upper oil pan, service parts PC3Z-6881-A (oil filter adapter), W503277-S439 (package of 6 bolts, 4 bolts required), W718564-S450 (stud), W520101-S442 (nut), and PC3Z-14A206-A (starter cable retaining bracket) will be needed to complete the repair.
SSM 51725
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51691
Service Bulletin/Repair Instructions
2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
TSB 23-2160
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with a 6.2L or 7.3L engine and a 10R140 transmission may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07F7 stored in the powertrain control module (PCM) and a loss of 10th gear. The vehicle may also exhibit harsh engagements and poor shift quality. This may be due to the sleeve in the CDF clutch cylinder shifting axially causing hydraulic circuit leaks. To correct the condition, follow the Service Procedure to replace the CDF clutch cylinder.
TSB 23-2161
Service Bulletin/Repair Instructions
Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
SSM 51648
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may experience a lack of power due to snow packing of the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22ÃÂðF (-30ÃÂðC). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10ÃÂðF (-12ÃÂðC) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.
TSB 23-2133
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the engine will not turn off and/or have various electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure to inspect for water/moisture intrusion into the BJB and replace the BJB and cover if water/moisture intrusion is found.
TSB 23-2115
Service Bulletin/Repair Instructions
Some 2015-2020 F-150 and 2017-2022 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 50974
Service Bulletin/Repair Instructions
Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
21M05-S1
Service Bulletin/Repair Instructions
Certain 2017-2022 Model Year Super Duty Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening. In the affected vehicles, some customers report experiencing an unintended tailgate opening and may have previously serviced their vehicle for this concern. Ford had developed an enhanced remedy for customers who may want this enhanced repair performed n their vehicle.
SSM 50830
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles equipped with a 7.3L engine and built on or before 11-May-2022 may exhibit a ticking/clicking/tapping noise at idle that is loudest at the front of the engine where the front timing cover meets the oil pan. This may be due to a cracked oil pump drive gear. If the noise originates from the lower front of the engine, remove the accessory drive belt and retest. If the noise is still present, remove the oil pan and rotate the crankshaft 360 degrees to inspect for cracking. If cracked, replace the oil pump drive gear (LC3Z-6306-A).
21P19-S1
Service Bulletin/Repair Instructions
Certain 2020-2021 Model Year Super Duty Vehicles - Reconfigure the RCM with As-Built Data. In all of the affected vehicles, the event data recorder (EDR) was inadvertently disabled. In the event of a crash or near crash-like situation, the event data recorder within the restraint control module (RCM) will not collect and store data used to help understand how the safety systems performed. There is no impact to normal vehicle operation or the vehicleâÂÂs safety systems.
TSB 22-2191
Service Bulletin/Repair Instructions
Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
SSM 50742
Service Bulletin/Repair Instructions
Some 2020-2022 F-Super Duty vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 for the ambient air temperature sensor stored in the powertrain control (PCM). When performing pinpoint test BF in Workshop Manual (WSM), Section 413-01, the ambient air temperature sensor/outside air temperature display reset procedure has been added to the Ford Diagnostic Repair System (FDRS) diagnostic scan tool. Depending on how the vehicle is equipped, run the FCIM or HVAC. Reset the Outside Air Temperature Sensor Learned Values application. Clear DTCs and retest after performing the reset procedure.
SSM 50636
Service Bulletin/Repair Instructions
2011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 50323
Service Bulletin/Repair Instructions
Some 2017-2022 F-Super Duty and 2016-2022 F-650/F-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
SSM 49483
Service Bulletin/Repair Instructions
Some 2017-2021 F-Super Duty and 2016-2021 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
SSM 49439
Service Bulletin/Repair Instructions
Some 2020-2021 F-Super Duty vehicles with 6.7L and 10R140 powertrain may exhibit an illuminated powertrain malfunction indicator (wrench) lamp with only DTC P07F6 stored in the transmission control module (TCM). The vehicle may also exhibit harsh engagements, poor shift quality and/or loss of 9th gear as a result of the DTC being set. If no additional DTCs or symptoms are present, clear keep alive memory and transmission adaptive tables with the appropriate Ford diagnostic scan tool, and perform an adaptive learning drive cycle. Transmission replacement is not necessary. Inform customers that a further improved calibration will be available in early March 2021. Let the customer know they can continue to drive the vehicle after performing this SSM, and schedule a service appointment for early March 2021. Monitor OASIS for updates.
TSB 20-2380
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with the 6.2L or 7.3L engine built on or before 05-Jun-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0132, P0135, P0138, P0141, P0152, P0155, P0158 and/or P0161 stored in the powertrain control module (PCM). This may be due to water intrusion into heated oxygen sensor (HO2S) connectors C141, C142, C1571 and/or C1572 on the transmission harness where it connects to the engine exhaust sensors. To correct the condition, follow the Service Procedure steps to replace the transmission harness and the affected heated oxygen sensors (HO2S) and/or the catalyst monitor sensor.
SSM 49286
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with an aftermarket bed may exhibit inoperative trailer lights on one or both sides of trailer after performing the FDRS Turn Signal Lamp Configuration application on the vehicle. Version 12 of this application is now available on the FDRS to address this trailer lighting condition. Make sure to download version 12 or later of the FDRS Turn Signal Lamp Configuration and follow the on screen prompts to configure the aftermarket bed. Verify the trailer lighting is operating correctly once complete. If the Turn Signal Lamp Configuration application was previously run on the vehicle, make sure to run the BCM Reset option before re-running the application.
TSB 20-2363
Service Bulletin/Repair Instructions
Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 20-2359
Service Bulletin/Repair Instructions
Some 2020 F-150/F-Super Duty vehicles built on 18-May-2020 and through 30-Jun-2020 may exhibit a concern where the right rear door lock is inoperative but the manual lock rod works. This may be due to stack up tolerances of the handle, cable and latch. To correct the condition, follow the Service Procedure to remove the cable barrel sleeve.
TSB 20-2336
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with a 6.7L engine built on or before 19-Aug-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0300-P0308, P0603, P203B, P208B, P208C, P2201, P24C2, P27B4, P07F6 and/or P27B5 stored in the powertrain control module (PCM). The vehicle may also exhibit a forced idle condition. This may be due to various strategies within the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 49185
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty and 2021 F-650/F-750 vehicles equipped with a 6.7L diesel engine built on 01-Mar-2020 and through 31-Aug-2020 may exhibit an illuminated malfunction indicator light (MIL) with diagnostic trouble code (DTC) P0088. This may be due to the pressure control valve in the left fuel rail. To correct the condition, replace the left fuel rail along with the pressure control valve (PCV). For F-250 through F-550 vehicles refer to Workshop Manual (WSM), Section 303-04B. For F-650/F-750 vehicles refer to WSM, Section 303-04A. For claiming use causal part 9D280 and applicable labor operations in Section 09 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2267
Service Bulletin/Repair Instructions
Some 2015-2020 F-150 except Raptor, 2017-2020 F-Super Duty, 2018-2020 Expedition vehicles equipped with a front camera washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.
TSB 20-2298
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles may exhibit a condition where the engine will not turn off and/or have various electrical symptoms including a dead battery, horn stays on and no crank/no start. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure steps to inspect for water/moisture intrusion into the BJB and replace the BJB if water/moisture intrusion is found.
SSM 49140
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with a 6.7L diesel engine and built on or before 18-Aug-2020 may exhibit an illuminated powertrain malfunction indicator (wrench) lamp with only diagnostic trouble code (DTC) P07F6 stored in the transmission control module (TCM). This DTC may be accompanied by harsh engagements, a poor shift quality feel and/or loss of 9th gear as a result of the DTC being set. If no additional codes or symptoms are present, clear the DTC with the appropriate Ford diagnostic scan tool and schedule a follow-up appointment for service mid-September. Inform the customer that engineering is working to implement a solution and advise the customer that they can continue to drive the vehicle. Once available, contact the customer and confirm a service appointment. Monitor OASIS for updates.
TSB 20-2259
Service Bulletin/Repair Instructions
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure
SSM 49038
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles built on or before 26May-2020 equipped with a high mounted stoplamp camera, may exhibit various concerns such as poor image quality, flickering and/or intermittent blank screen. If a vehicle exhibits any of these conditions replace the high mounted stoplamp camera. Refer to Workshop Manual (WSM), Section 417-01. For claiming, use causal part 19G490 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 49032
Service Bulletin/Repair Instructions
Some 2020 Corsair/Explorer/Super Duty vehicles built on or before 27-May-2020 and not equipped with a 360-camera system may exhibit various rear parking aid camera concerns such as poor image quality, flickering and/or completely inoperative. If a vehicle exhibits any of these conditions, replace the rear parking aid camera. Refer to Workshop Manual (WSM), Section 413-13. For claiming, use causal part 19G490 and any applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual
SSM 48958
Service Bulletin/Repair Instructions
Some 2020 Super Duty vehicles equipped with an 10R140 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) and/or wrench light with diagnostic trouble codes (DTCs) P0715, P0716, P0717, P0718, P07BF and/or P07C0 stored in the powertrain control module (PCM). If any of these DTCs are set, focus diagnostics on the turbine shaft speed sensor (TSS) and/or TSS circuits. Refer to Workshop Manual (WSM), Section 307-01. Replacement of the ISSA or ISSB sensor will not correct this condition.
SSM 48868
Service Bulletin/Repair Instructions
Some 2020 F-Super Duty vehicles equipped with the Blind Spot Information System (BLIS) and Cross Traffic Alert (CTA) may require the removal of the factory equipped tail lamps to accommodate the use of aftermarket equipment. Once the tail lamps are removed, this may result in BLIS and CTA warning indicators illuminated in the instrument panel cluster (IPC). To clear these warning indicators, the BLIS and CTA systems will need to be disabled using the FDRS scan tool. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. Locate the application labeled Disable/Enable Blind Spot Information System. Download and run this application to enable or disable the BLIS And CTA systems.