Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51181
Service Bulletin/Repair Instructions
Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
TSB 22-2396
Service Bulletin/Repair Instructions
Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 22-2309
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
TSB 22-2230
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
SSM 50744
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
TSB 22-2066
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50258
Service Bulletin/Repair Instructions
Various 2012-2015 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed.
SSM 50064
Service Bulletin/Repair Instructions
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 21-2152
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 21-2033
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 20-2372
Service Bulletin/Repair Instructions
This article supersedes 17-2225 to update the vehicle model years affected and Service Procedure. Some 2013-2014 Fusion and 2013-2020 MKZ vehicles may exhibit unintended exterior mirror movement in wet weather conditions. This may be due to water intrusion into the exterior mirror connector. To correct the condition, follow the Service Procedure steps to remove the 16 pin connector and install two weather tight 8 pin connectors.
SSM 49210
Service Bulletin/Repair Instructions
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2233
Service Bulletin/Repair Instructions
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
TSB 20-2219
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion/MKZ/C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
SSM 48858
Service Bulletin/Repair Instructions
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 48301
Service Bulletin/Repair Instructions
Some 20132017 C-MAX Energi, 20172018 C-MAX Hybrid, 20132020 Fusion Energi and 2017-2020 Fusion/MKZ Hybrid vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with any of the following diagnostic trouble codes (DTCs): P0496, P1450, P04ED, P04EF, P04EE, P2450, P2451. When performing pinpoint test (PPT) HX in the Powertrain Controls and Emission Diagnosis (PC/ED) Manual for the referenced DTCs, incorrect results may be obtained due to an internal powertrain control module (PCM) software conflict. In order to make sure the PPT provides accurate results, immediately prior to step HX22, make sure the fuel door is fully latched and then press the fuel door release button. Keep the door open while completing HX22, then fully latch again, prior to continuing the remainder of testing
TSB 19-2207
Service Bulletin/Repair Instructions
Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
TSB 18-2373
Service Bulletin/Repair Instructions
Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2019 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
SSM 47428
Service Bulletin/Repair Instructions
Some 2013-2018 Fusion Energi, 2012-2018 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 110.03 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
tsb18-2216
Service Bulletin/Repair Instructions
Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
SSM 46371
Service Bulletin/Repair Instructions
SOME 2012-2017 FOCUS ELECTRIC/2013-2017 CMAX ENERGI/FUSION ENERGI/2015-2017 MKC/MKZ/2016-2017 MKX AND 2017 CONTINENTAL VEHICLES OPERATING WITH A 3G TCU ON OR BEFORE 16-JAN-2017 MAY NOT RESPOND TO CUSTOMERS REMOTE COMMANDS VIA MYLINCOLN/MYFORD MOBILE PHONE APPLICATIONS. 2G NETWORKS WERE DECOMMISSIONED ON 16-JAN-2017. IF THE 3G TCU WAS OPERATING ON A 2G NETWORK, IT WILL NOT AUTOMATICALLY ATTEMPT TO RECONNECT TO THE REPLACEMENT 3G NETWORK. TO CORRECT, RESET THE TCU BY REMOVING ITS POWER FUSE FOR 5 MINUTES. IF THE CONCERN IS STILL PRESENT, FOLLOW NORMAL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. REFER TO PTS OASIS HOME PAGE FOR TCU VERSION IDENTIFICATION. FOR CLAIMING, USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
15N04-S2
Service Bulletin/Repair Instructions
CERTAIN 2015 MODEL YEAR MKC AND MKZ VEHICLES EQUIPPED WITH THE RESERVE EQUIPMENT GROUP, AND CERTAIN 2012-2016 FOCUS ELECTRIC, C-MAX ENERGI, AND FUSION ENERGI VEHICLES - EMBEDDED MODEM REPLACEMENT.
Service
Service Bulletin/Repair Instructions
Online automotive service information system for March 2016
44863
Service Bulletin/Repair Instructions
FORD: NO SERVICE ACTION IS RECOMMENDED FOR THIS CONDITION. PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA
ASI-45098
Service Bulletin/Repair Instructions
FORD: THE BATTERY ENERGY CONTROL MODULE (BECM) NEEDS REPROGRAMMING TO LATEST CALIBRATION TO RESET DIAGNOSTIC TROUBLE CODE (DTC) P0B13 AFTER CONNECTING TO ELECTRIC CHARGING STATION. MODEL 2013-15 C-MAX PHEV, FUSION PHEV. *PE
15-0028
Service Bulletin/Repair Instructions
FORD FUSION 2013: CERTAIN FUSION ENERGI VEHICLES MAY EXPERIENCE NO START WITH A DISCHARGED BATTERY OR INTERMITTENT BATTERY DRAW. *LJ
45008
Service Bulletin/Repair Instructions
FORD 2013-2015 FUSION ENERGI : BULLETIN INFORMATION REGARDING OPEN BATTERY COOLING FAN FUSES F35 OR F36, OR AN INTERMITTENT 12 VOLT BATTERY DRAW. *LJ
ASI-44641
Service Bulletin/Repair Instructions
FORD: VEHICLES ARE EXPERIENCING A DELAY OPENING OR STUCK CLOSED ON THE FUEL DOOR AFTER RELEASE BUTTON ON CENTER CONSOLE IS PRESSED. MODEL 2013-14 C-MAX ENERGI, FUSION ENERGI. *PE
TSB-14-0106
Service Bulletin/Repair Instructions
LINCOLN/FORD: ACCOMPANIED BY CMDTC P1A18, P1A19, P0AEE OR P0BCD, THE WRENCH LAMP (HYBRID) OR SERVICE ENGINE SOON LIGHT MAY ILLUMINATE AND THE POWERTRAIN CONTROL MODULE (PCM) NEEDS TO BE REPROGRAM TO LATEST CALIBRATION. MODEL 2013-2014 FUSION, MKZ. *PE
TSB-14-0089
Service Bulletin/Repair Instructions
FORD/LINCOLN: ACCOMPANIED BY THE CMDTCS P1A18, P1A19, P0AEE OR P0BCD, THE SERVICE ENGINE SOON LAMP (ENERGI) OR WRENCH LAMP (HYBRID) WILL ILLUMINATE ON SOME VEHICLES. MODEL 2013-2014 C-MAX, FUSION, MKZ. *PE
TSB-14-0085
Service Bulletin/Repair Instructions
FORD/LINCOLN: DUE TO AN ADHERENCE FAILURE OF RTV SEALANT, THERE IS A TRANSMISSION FLUID LEAKAGE, IN SOME VEHICLES, FROM DAMPER HOUSING TO TRANSMISSION CASE JOINT. MODEL 2013 C-MAX, 2013-14 FUSION, MKZ. *PE
ASI-44451
Service Bulletin/Repair Instructions
FORD: SOME MODEL VEHICLES MANUAL FOR POWERTRAIN CONTROL/EMISSION DIAGNOSTIC (PC/ED) HAS BEEN UPDATED REGARDING IMPROVED COOLING FAN CIRCUIT DUE TO A LACK OF AIR CONDITIONING, A MALFUNCTIONING INDICATOR LAMP (MIL) AND OVERHEATING. *PE
TSB-14-0005
Service Bulletin/Repair Instructions
FORD: THE ENGINE LAMP OR THE WRENCH WILL BE ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS) P26CA AND/OR U019F. MODEL 2013-2014 FUSION, MKZ. *PE
ASI-44401
Service Bulletin/Repair Instructions
FORD: WHEN THE OIL MAINTENANCE ON, IN DISPLAY MESSAGE CENTER, VEHICLE GAS ENGINE CONTINUOUSLY RUN AND ELECTRIC ONLY OPERATION IS NOT AVAILABLE, AND NOT BE CONFUSED WITH OIL CHANGE MONITOR. 2013-2014 C-MAX, FUSION ENERGI. *PE
TSB-14-0020
Service Bulletin/Repair Instructions
LINCOLN/FORD: ON SOME VEHICLES, THE ILLUMINATION OF THE WRENCH LAMP AND/OR RED TRIANGLE LAMP, THE CHECK ENGINE LAMP IS ACCOMPANIED WITH VARIOUS DIAGNOSTIC TROUBLE CODES (DTCS) AND SERVICE PROCEDURES UPDATES. MODEL 2013 C-MAX, FUSION, MKZ. *PE
TSB-13-12-23
Service Bulletin/Repair Instructions
FORD: THE HIGH VOLTAGE BATTERY, FAILS TO CHARGE, WHEN USING EITHER 120 VOLT LEVEL 1 ELECTRIC VEHICLE SERVICE EQUIPMENT (EVSE) OR THE 240V LEVEL 2 EVSE AND MAY NEED BECM REPROGRAMMED AND RECALIBRATED. MODEL 2013 C-MAX, 2013-2014 FUSION. *PE
ASI-44339
Service Bulletin/Repair Instructions
FORD/LINCOLN: THE WRENCH LAMP (HYBRIDS) OR SERVICE ENGINE SOON LAMP (ENERGI) WILL ILLUMINATE WHEN USING ENGINE BLOCK HEATER AND LAMPS TURN OFF WITHIN NO MORE THAN THREE DRIVE CYCLES AFTER UNPLUGGING ENGINE BLOCK HEATER. MODEL 2013-2014 C-MAX, FUSION, MKZ HYBRID/ENERGI. *PE
ASI-44302
Service Bulletin/Repair Instructions
FORD: AFTER BEING FULLY CHARGED, THE EV RANGE MAY BE DISPLAYED AND DISTANCE TO EMPTY FEATURE IS SIMILAR TO CONVENTIONAL GASOLINE VEHICLE AND HOW VEHICLE WAS DRIVEN PRIOR TO CHARGING BATTERY. MODEL 2012-2014 FOCUS ELECTRIC, 2013 C-MAX ENERGI, 2013-2014 FUSION ENERGI. *PE