Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55140
Service Bulletin/Repair Instructions
Some 2025-2026 Maverick vehicles built on or before 05-Dec-2025 and 2024-2026 Nautilus vehicles built on or before 04-Sep-2025 may exhibit limited power and display "Stop Safely Now" or "Service Vehicle Soon" stored in the message center after start up with diagnostic trouble codes (DTC) P0A5D, P0A60, P0A63, P0A6F, P0A72, P0A75, and/or P0E52 stored in the inverter system controller (SOBDMC). The Ford Diagnostic and Repair System (FDRS) may refer to this module as the "Secondary On-Board Control Module C". If the vehicle exhibits these conditions, replace the inverter system controller. Refer to Workshop Manual, Section 307-01B. For claiming, use causal part 7B012 and labor operations 12651D and 12651D56. NOTE: This article does not remove any RVC, Prior Approval or Warranty and Policy requirements for component replacement.
SSM 55100
Service Bulletin/Repair Instructions
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
SSM 55058
Service Bulletin/Repair Instructions
Some 2025-2026 Maverick vehicles built on or before 05-Dec-2025 and 2024-2026 Nautilus vehicles built on or before 04-Sep-2025 may exhibit limited power and display "Stop Safely Now" or "Service Vehicle Soon" stored in the message center after start up with diagnostic trouble codes (DTC) P0A5D, P0A60, P0A63, P0A6F, P0A72, P0A75, and/or P0E52 stored in the inverter system controller (SOBDMC). The Ford Diagnostic and Repair System (FDRS) may refer to this module as the "Secondary On-Board Control Module C". If the vehicle exhibits these conditions, replace the inverter system controller. Refer to Workshop Manual, Section 307-01B. For claiming, use causal part 7B012 and labor operations 12651D and 12651D58. NOTE: This article does not remove any RVC, Prior Approval or Warranty and Policy requirements for component replacement.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 55021
Service Bulletin/Repair Instructions
Some 2025-2026 Bronco/Bronco Sport/Corsair/F-150/F-Super Duty/Maverick/Mustang/Mustang Mach-E/Ranger vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 10654C, 12651D and 12651D4.
SSM 55008
Service Bulletin/Repair Instructions
Some 2021-2026 Ford vehicles may exhibit inoperative heated/cooled seats, heated steering wheel and/or front/rear defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a
SSM 54963
Service Bulletin/Repair Instructions
Some 2025-2026 Maverick and 2026 Transit/Bronco Sport vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q3 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report. Do not use the "Report A Problem" link to submit a report for this condition.
SSM 54939
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim
SSM 54942
Service Bulletin/Repair Instructions
Some 2025-2026 Maverick/Bronco Sport and 2026 Transit vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q3 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report. Do not use the "Report A Problem" link to submit a report for this condition.
SSM 54918
Service Bulletin/Repair Instructions
Some of the following vehicles: 2025-2026 Mustang Mach-E vehicles built on or before 27-Jan-2026 2025-2026 Maverick/Bronco Sport vehicles built on or before 20-Jan-2026 2024-2026 Nautilus vehicles built on or before 02-Dec-2025 2023-2026 Escape/Corsair may exhibit reduced steering assist and a "Power Steering Assist Fault" message displayed in the instrument panel cluster (IPC) with the diagnostic trouble code (DTC) U2016:47 only, and no other steering DTCs stored in the power steering control module (PSCM). To correct this condition, reprogram the PSCM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 3C529 and labor operations 3504E and PSCM. If a software update is not available for the PSCM, the PSCM is already at the latest software level. Refer to Workshop Manual (WSM), Section 211-02 for normal diagnostics. If the vehicle does not exhibit any observable symptoms described above and the DTC is only present in continuous memory, this DTC should be ignored. No further service action
SSM 54857
Service Bulletin/Repair Instructions
2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
SSM 54823
Service Bulletin/Repair Instructions
Some 2025-2026 Maverick vehicles built on or before 05-Dec-2025 and 2024-2026 Nautilus vehicles built on or before 04-Sep-2025 may exhibit limited power and display "Stop Safely Now" or "Service Vehicle Soon" stored in the message center after start up with diagnostic trouble codes (DTC) P0A5D, P0A60, P0A63, P0A6F, P0A72, P0A75, and/or P0E52 stored in the inverter system controller (SOBDMC). The Ford Diagnostic and Repair System (FDRS) may refer to this module as the "Secondary On-Board Control Module C". If the vehicle exhibits these conditions, replace the inverter system controller. Refer to Workshop Manual, Section 303-14B for Nautilus and 303-14C for Maverick. For claiming, use causal part 7B012 and labor operations 12651D, 12651D4 and 12651D58. <br /><br /> NOTE: This article does not remove any RVC, Prior Approval or Warranty and Policy requirements for component replacement.
SSM 54822
Service Bulletin/Repair Instructions
All 2026 Maverick non-Lobo vehicles equipped with a 2.0L engine and built on or after 04-May-2026 and all 2026 Bronco Sport vehicles built on or after 07-May-2026 are no longer equipped with an underbody tunnel shield (Maverick base part number 6011434/Bronco Sport base part number 7811434). The vehicle is not misbuilt and the installation of this part is not a warrantable repair. Do not submit a claim for this condition.
SSM 54797
Service Bulletin/Repair Instructions
Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation.
ITRM-25.A04 Maverick
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
SSM 54765
Service Bulletin/Repair Instructions
Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
SSM 54769
Service Bulletin/Repair Instructions
Bronco Sport and Maverick vehicles utilize an advanced headlamp design that features a sharp horizontal light-to-dark transition. This is an intentional optical characteristic designed to meet safety and performance standards. This transition is a normal attribute of the vehicles lighting signature and is most visible during high-beam operation. No repair is required as the system is functioning to specification. Workshop Manual (WSM), Section 417-01 Exterior Lighting > Description and Operation > Exterior Lighting - Overview has been revised to clarify this condition as an operating characteristic of the vehicle.
PT-26.10.0 Maverick
Over The Air
25C69 Recall remedy - Updates the Secondary On-Board Diagnostic Module C to provide for release of the Integrated Park Module slider in the event a bind condition occurs allowing park to be engaged.
SSM 54741
Service Bulletin/Repair Instructions
Some 2025-2026 Escape/Maverick/Bronco Sport vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q3 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor PTS for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.
26U02
Other
Update Prior to Sale Certain 2026 Model Year Maverick Vehicles Equipped With Steel Wheels Wheel Center Cap Inspection. On some of the affected vehicles, the wheel center caps may not fit tight and/or be retained to the wheel. This is due to a manufacturing error that occurred with wheel center caps built on November 10, 2025.
TSB 26-2092
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2466 to add Bronco Sport, Escape, Maverick and Corsair, as well as removing Expedition and Navigator. One time use parts for Corsair and Bronco Sport were also added to the parts list. Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 54586
Service Bulletin/Repair Instructions
Some 2025-2026 Escape/Maverick/Bronco Sport vehicles equipped with an 8-inch instrument panel cluster (IPC) display may exhibit a condition where the fuel gauge displays up to the 8th mark below full fuel level when the fuel tank is full. This condition does not affect vehicle durability and no additional diagnosis or service is required at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of Q2 2026. Replacement/reprogramming of the IPC will not resolve this condition. Monitor PTS for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GCR form, referencing this article number in the report.