Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
SSM 55028
Service Bulletin/Repair Instructions
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
SSM 55008
Service Bulletin/Repair Instructions
Some 2021-2026 Ford vehicles may exhibit inoperative heated/cooled seats, heated steering wheel and/or front/rear defrost features after a remote start is performed through the Ford mobile application or with the key fob. Customers may also experience heated/cooled seats, heated steering wheel and/or front/rear defrost features turning on in unexpected conditions such as during warmer weather. These features will operate normally when commanded in the center display screen. This may be due to the customer not setting up their "Climate Settings" through the Ford mobile application. To correct this condition, inform the customer they should perform a remote start from the Ford mobile application and then adjust the "Climate Settings" in the Ford mobile application as desired. These settings only need to be set once and will persist through subsequent remote starts. Heated and cooled seats will be set to Level 2 when turned ON via "Climate Settings" in the Ford mobile application during a remote start event. This is normal operating characteristic. This condition does not affect vehicle durability and no a
TSB 26-2324
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit a distorted or muffled sound originating from the center speaker. This may be due to a deformed speaker cone.
GSM-26.2651B MachE
Over The Air
Quality improvements include: - Updates the motor short failure detection logic to prevent Diagnostic Trouble Codes
SSM 54995
Service Bulletin/Repair Instructions
Some 2023-2026 Mustang Mach-E vehicles equipped with a lithium iron/ion phosphate (LFP) standard range battery (minor feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026. If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number ÝVIN¨ required) and fill out the form. Do not use the "Report A Problem" link to submit a report for
SSM 54991
Service Bulletin/Repair Instructions
Some 2023-2026 Mustang Mach-E vehicles equipped with a lithium iron/ion phosphate (LFP) standard range battery (minor feature code HTHAH) may exhibit a battery energy control module (BECM) state of health reading that over-estimates the actual high voltage battery state of health after a BECM replacement directed by the Workshop Manual (WSM). This may be due to the software in the BECM. To correct this condition, download and run the "BECM-High Voltage Battery Capacity Relearn" application using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 10B687 and labor operations 12651D and 12651D4. The engineering team is currently working on a permanent software solution which is expected to be available in Q4 of 2026.<br /><br /> If a vehicle exhibits this concern, submit a Global Concern Report (GCR). To submit a report, click on the "Submit Global Concern Report (GCR)" link at the upper right of the Professional Technician System (PTS) Vehicle ID screen (vehicle identification number ÝVIN¨ required) and fill out the form. Do not use the "Report A Problem" link to submit
SSM 54979
Service Bulletin/Repair Instructions
Some 2023-2025 Mustang Mach-E and 2024-2026 F-Super Duty vehicles equipped with a 360-degree camera may exhibit a distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q3 of 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS
TSB 26-2297
Service Bulletin/Repair Instructions
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
SSM 54917
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E vehicles may exhibit only continuous memory diagnostic trouble code (DTC) U2016:47 stored in the power steering control module (PSCM) after a self test is performed with the Ford Diagnosis and Repair System (FDRS) scan tool. If the vehicle does not exhibit any observable symptoms such as lack of/reduced power steering assist, disabling of power steering assist features and/or power steering assist fault messages displayed on the instrument panel cluster (IPC), this DTC should be ignored. No further service action is required.
ACM-26.S MachE
Over The Air
Quality improvements include: -Addresses a potential communication condition that may result in a loss of radio audio.
SYNC-26.2.8.3 MachE
Over The Air
Quality improvements include: -Privacy robustness updates -Restores the Auto Hold toggle in the controls menu
SSM 54811
Service Bulletin/Repair Instructions
2022-2026 Mustang Mach-E vehicles built on or after 03-Jan-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
PT-26.13.6 MachE
Over The Air
25C69 Recall remedy - Updates the Secondary On-Board Diagnostic Module C to provide for release of the Integrated Park Module slider in the event a bind condition occurs allowing park to be engaged.
SSM 54635
Service Bulletin/Repair Instructions
Some 2024-2025 Mustang Mach-E/F-150 vehicles may exhibit a crackling noise from speakers during phone calls when using wireless Apple CarPlay or wireless Android Auto. This may be due to wireless interference. To isolate the wireless interference as a possible cause, turn off the wireless projection application in SYNC Connectivity settings in the vehicle's center touch screen and connect the phone through universal serial bus (USB) cable. If the call quality issue through Apple CarPlay or Android Auto is addressed, this confirms that wireless projection was the cause. Engineering is aware of this condition and working on a software solution expected at the end of Q4 2026. As a temporary solution, customers can connect their phones with a USB cable. Reprogramming or replacement of any modules will not correct the condition. Use the "Submit Global Concern Report (GCR)" link at the upper right of the OASIS report to submit a vehicle concern report if the wireless projection is found to be the cause of the condition.
SYNC-26.2.1.6.5.2 MachE
Over The Air
26C10 Recall remedy -Addresses instances where the trailer lights and trailer brakes may not function
OBCC-AS.AU MachE
Over The Air
Quality improvements include: - Addresses false warnings attributed to the Off-board Charging Module. These warnings occur due to external charging station failures rather than internal module issues.
SSM 54555
Service Bulletin/Repair Instructions
Some 2020-2022-Corsair, 2021-2023 Nautilus, 2020-2024 Navigator/Aviator, and 2021-2024 Mustang Mach-E vehicles equipped with phone-as-a-key may exhibit various phone-as-a-key concerns with diagnostic trouble codes (DTC) U200D:15, U200E:15, U200F:15, B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 stored in the remote function actuator (RFA) module. If any of these DTCs are detected during diagnostics, clear the DTCs, reprogram the RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B1589:31/49 through B1598:31/49, B1A56:31/49, B1D55:31/49, and/or B15A5:56 DTCs return in the RFA after a self-test, follow normal Workshop Manual (WSM) diagnostics in Section 419-01. Repair as necessary outside of this article. For claiming, use causal part 14G617 and labor operations 12651D and 12651D4.
TSB 25-2622
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Stuck in park * "Service Vehicle Soon" message in the instrument panel cluster (IPC) * Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P07E6:71 stored in the secondary on-board diagnostic control module C (SOBDMC) This may be due to high ground resistance of the park pawl motor.
SSM 54493
Service Bulletin/Repair Instructions
Some 2023-2025 Mustang Mach-E and 2024-2026 F-Super Duty vehicles equipped with a 360 degree camera may exhibit a distorted or blurry 360 degree camera image in the center display screen, but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q2 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
TSB 25-2610
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2189 to update the vehicles affected, production cut-off date and part list. Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.
SSM 54424
Service Bulletin/Repair Instructions
Some 2021-2025 Mustang Mach-E vehicles may exhibit a condition where the front luggage compartment hood is hard to close. This may be due to an alignment issue with the hood. The most common adjustments to improve closing efforts involve the hood front up and down alignment and the bump stop rubbers. Refer to Workshop Manual, Section 501-03 Body Closures > General Procedures > Hood Alignment for procedures on proper adjustments that can improve front luggage compartment hood closing efforts.
SSM 54403
Service Bulletin/Repair Instructions
* 2021-2024 Bronco Sport built on or before 15-Dec-2024<br /> * 2022-2024 Mustang Mach-E<br /> * 2022-2025 Escape built on or before 22-May-2025<br /> * 2024 Maverick vehicles built on or after 17-Jan-2024<br /> <br /> Some of the above vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct the condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and labor operation numbers 7001D and 7001D4.
SSM 54387
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E vehicles may exhibit a condition where the interior propulsion sound feature does not remain active and deactivates immediately. This may be due to the audio control module (ACM) configuration. To restore the functionality of this feature, download and run the "ACM - Enable Engine Sound Enhancement and Active Noise Control" application in the Ford Diagnosis and Repair System (FDRS) scan tool. In cases where the ACM is replaced, this routine will run during the "ACM - Programmable Module Installation (PMI)" application. Make sure to follow the FDRS on-screen instructions carefully. For claiming, use causal part 18C869 and labor operation numbers 12651D and 12651D4.
PT-25.13.4 MachE
Over The Air
25S65 Recall remedy -Prevents a potential lock-out condition caused by the vehicle's battery being discharged
SSM 54334
Service Bulletin/Repair Instructions
Some 2023-2025 Mustang Mach-E vehicles equipped with a lithium iron phosphate (LFP) standard range battery (minor feature code HTHAH) built on or after 23-Jun-2023 may exhibit a condition where the displayed high voltage (HV) battery state of charge (SOC) percentage has a sudden reduction greater than 10% while driving. At low SOC, this may also result in a reduction of vehicle power with a turtle light displayed in the cluster. This concern may occur if the vehicle has not been charged to 100% for an extended period of time as this leads to an inaccurate displayed SOC. Advise customers to charge their vehicle to 100% at least once per month to reset the SOC measurement or more often if the condition persists. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).
TSB 25-2512
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 25-2427
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an inoperative Blue Cruise and Lane Keeping system with diagnostic trouble code (DTC) U3000:49 with a status byte of 8F stored in the camera module-rear (CMR). This may be due to the CMR software level. NOTE: The driver status monitor camera module may also be called camera module-rear.
SSM 54193
Other
Some 2024-2025 Mustang Mach-E/F-150/F-Super Duty vehicles equipped with 360 degree camera may exhibit a distorted or blurry 360 degree camera image in the center display screen but the rear view camera image is operating correctly. To restore the 360 degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected by the end of 2025. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available.
25P25
Other
Certain 2024-2025 Model Year Mustang Mach-E Vehicles Antenna Plate Film Removal
SSM 54140
Service Bulletin/Repair Instructions
Some 2021-2024 F-150 vehicles equipped with a B&O audio system (minor feature code IDBBQ), and various 2021-2024 Ford and Lincoln vehicles equipped with a B&O audio system may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). This may be due to software in the digital signal processing (DSP) module. To correct this condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 18B849 and labor operations 12651D and 12651D4.
DSMC-24.5.7 MachE
Over The Air
Quality improvements include: -Addresses a Diagnostic Trouble Code that causes the Driver State Monitoring Camera module to get stuck in bootloader
SSM 54090
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
SSM 54065
Service Bulletin/Repair Instructions
Some 2022-2024 Mustang Mach-E vehicles may exhibit an inoperative BlueCruise and lane centering with diagnostic trouble code (DTC) U3000:49 stored in the camera module rear (CMR). This may be due to the software level of the CMR. Inform customers that engineering is currently working on a solution for this condition that is expected in Q3 2025. Monitor Professional Technician System (PTS) for additional information.
ACM-25.AH.AR MachE
Over The Air
Quality improvements include: -Addresses potential SiriusXM no audio and a false banner showing "Hardware problem"
SSM 53973
Service Bulletin/Repair Instructions
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
TSB 25-2274
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above equipped with lithium-ion phosphate (LFP) standard range battery with minor feature code HTHAH may exhibit an illuminated powertrain malfunction indicator (wrench) lamp with the DTC P0C28 stored in the SOBDMC
DCMX-25.BB MachE
Over The Air
Quality improvements include: -This update prevents a potential issue that may prevent side doors from unlocking when commanded from the exterior of the vehicle following a future over-the-air update.
25-OTA ACM-25.AH.AR MachE
Over The Air
Quality improvements include: -Radio reflash to include AM radio option -Addresses a potential SiriusXM false banner showing "Hardware problem"
25-SYNC-25.2.1.6.5 MachE
Over The Air
Quality improvements include: -Latest SYNC deployment to enable BlueCruise"
TSB 25-2189
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2149 to update the labor operation allowance. Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.
24N08 -S1
Other
Customer Satisfaction Program 24N08 - Supplement #1 Certain 2021-2024 Bronco Sport, Escape, Mach-E, and 2022-2024 Maverick Vehicles Driver’s Side Seat Buckle Replacement
25-OTA SU-10.2.0 MachE
Over The Air
Quality improvements include: - Key off load battery drain prevention by ensuring the Battery Charge Control Module properly goes to sleep
TSB 25-2145
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above equipped with extended range battery may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0ADA stored in the battery energy control module (BECM). This may be due to the BECM software level.
TSB 25-2149
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may experience exterior paint blistering in at least one of the following areas: * Front and rear door skin panel(s) and door jamb area(s) * Rear quarter panel(s) and jamb area(s) * B-pillar outer panel(s) and jamb area(s) * Roof panel and jamb area(s) * Rocker panel(s) and jamb area(s) This may be due to the factory painting process.
SSM 53569
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles may exhibit diagnostic trouble code (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
SSM 53530
Service Bulletin/Repair Instructions
Some 2021-2025 Ford vehicles may exhibit a condition where heated/cooled seats, heated steering wheel and/or front/rear defrost features will not turn on after a remote start is performed through the FordPass application or the key fob.
TSB 25-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2251 to update the labor times associated with the Service Procedure from M-time to AP-time.
TSB 25-2106
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2049 to update the labor time description.
24U14
Other
Update Prior to Sale 24U14 Certain 2024 Model Year Mustang Mach E and F-150 Lightning Battery Electric Vehicles (BEV) Audio Control Module (ACM) Software Update
TSB 25-2049
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * General system performance/stability/intermittent system reboot * Intermittent wireless Apple CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through Apple CarPlay and Android Auto * Alexa function consistency and stability
25B03
Service Bulletin/Repair Instructions
Certain 2024 Model Year Mustang Mach-E vehicles High Voltage Battery Charging System Software Update
TSB 25-2040
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an unintended deceleration without a vehicle in front when using adaptive cruise control (ACC) or BlueCruise. This may be due to the front bumper affecting both corner radar sensor signals.
25H01
Other
This program includes sixty VINs, specifically identified, unsold 2024 Mach-E vehicles at certain dealer locations. At this time, there is no corresponding owner letter or repair procedure. We are evaluating a potential paint quality concern.
TSB 24-2445
Service Bulletin/Repair Instructions
Some 2023-2024 Mustang Mach-E vehicles built on or before 06-Dec-2024 may exhibit a condition where the high voltage battery does not charge while using a DC fast charger level 3 and a charge error message displayed on the charger with DTC U049C stored in the BECM.
SSM 53167
Service Bulletin/Repair Instructions
For 2022-2024 e-Transit vehicles equipped with the standard range battery with engine code "ENC0" and 2021-2024 Mustang Mach-E vehicles when attempting to charge/balance high voltage battery modules (arrays) from remanufactured array kits, the Midtronics xMB tool will not recognize the remanufactured part number.
SSM 53133
Service Bulletin/Repair Instructions
Some 2022-2024 Mustang Mach-E vehicles may exhibit an inoperative BlueCruise and lane centering with diagnostic trouble code (DTC) U3000:49 stored in the camera module rear (CMR).
SSM 53088
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
OTA SU 10.1.1 Mach E
Over The Air
-Improved connectivity. -Reduces Telematics Control Unit based Key Off Load battery drain. - Map orientation improvement - removes falseIP Configuration Failure" message when wrong WiFi password is entered. - Improves functionality of Stolen Vehicle Services
SSM 53018
Service Bulletin/Repair Instructions
Some 2021-2024 Ford and Lincoln vehicles may exhibit diagnostic trouble codes (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
SSM 52925
Service Bulletin/Repair Instructions
Some 2020-2024 Explorer/Aviator/Corsair, 2021-2024 F-150/Bronco, 2023-2024 F-Super Duty, and 2024-2025 Nautilus vehicles may experience the overhead console sunglass bin cannot be locked in a closed position.
OTA SU10.1.0 23-24 MachE
Over The Air
Quality improvements include: -Allows SYNC strategy for Charge Status message to match Cluster strategy. - Top off the Low Voltage battery prior to OTA update. (EV only) - Enables Public Charging App function above 5 MPH. - Hides "Update Now" button on HMI when the vehicle battery health is below threshold. - Corrects "Bluecruise Maps not up to date" erroneous message. - Improves Key Off Load battery drain due to SYNC.
24B35
Service Bulletin/Repair Instructions
In some of the affected vehicles, if an attempt is made to repair a flat tire using the sealant system included in the vehicle’s tire sealant and inflator kit, the system will not provide sealant or air to inflate and seal the tire. The air-only function will operate as expected.
OTA SU 24.2.5.6.2 MachE
Over The Air
Quality Improvements include: - Addresses Accessory Protocol Interface Module (SYNC) displaying update status as not completed. - Reduction in Key off load battery drain via Enhanced Central Gateway (ECG) controlled reset. - Reduction in Key off load battery drain due to Bluetooth Low Energy Module (BLEM) software - Addresses potential lock out condition post OTA update.
TSB 24-2251
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).
24OTA SU24.2.4.10 Mach-E
Over The Air
Quality Improvements include: - 23 MY Robustness action to improve Phone as a Key Feature Key functionality post Enhanced Central Gateway (ECG) reset. - 23 MY Minor quality fixes in Enhanced Central Gateway (ECG) Software, not affecting vehicle operation. - Addresses potential unintended lock out of vehicle after OTA update.
TSB 24-2230
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2002 to update the symptom, production fix date and the service procedure. Some 2021-2024 Mustang Mach-E vehicles built on or before 09-Jul-2024 may exhibit a wind noise from the exterior mirrors/A-pillar area when driving between 25 mph-40 mph (32 km/h-64 Km/h). This may be due to poor sealing of the lower mirror foam and the glass top run foam. To correct this condition, follow the Service Procedure to install new lower inner foam and the glass top run foam.
OTA IPMA-24.204.8.27Mach
Over The Air
Quality improvements include: - Reduced ADAS loss of communication events - Adds camera retry strategy robustness action - 21 MY: Removes erroneous ""Reverse Brake Unavailable"" message.
24U08
Service Bulletin/Repair Instructions
Certain 2024 Model Year Mustang Mach-E Vehicles Powertrain Control Module Software Update In some of the affected vehicles, the charge status indicator (CSI) displays in RED (fault) for a short period after the charge plug is unlocked from the charge port during vehicle level 3 (L3) charging. All vehicles are charged correctly and no warning shows in the instrument cluster.
OTAECG-24.2.4.9 Mach E
Over The Air
Quality Improvments include: - Phone as a Key resolution, not affecting customer vehicles.
SSM 52574
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
24B17
Service Bulletin/Repair Instructions
Certain 2024 Model Year Mach-E Vehicles - Reprogram Secondary On-Board Diagnostic Module (SOBDM)
SSM 52465
Service Bulletin/Repair Instructions
Some 2023-2024 Mustang Mach-E/Corsair and 2024 Mustang vehicles may exhibit an audio control module (ACM) programming failure with a message displayed in the Ford Diagnosis and Repair System (FDRS) scan tool indicating Procedure Unsuccessful-Flash Software Failed To Flash. This may be due to the ACM programming routine. To correct this condition, download and click the refresh icon located next to the run icon to update the ACM - Programmable Module Installation (PMI) app. For claiming, use causal part 18C869 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
OTAPU0227VIRBSME
Service Bulletin/Repair Instructions
Quality improvements include: Numerous minor quality fixes in ECG RC9 which are not customer facing. Improves OTA deployment reduce FTDI risk.
SSM 52345
Service Bulletin/Repair Instructions
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
OTAPU0121FTDI-FX
Service Bulletin/Repair Instructions
Software Update FPU 24-PU0121-FTDI-FX for 2023-2024 MY Mach E vehicles is now available. Quality Improvements include - FordPass will remember last known profile. - Allow customers to exit during OTA update. - Improves BCM response to de-inhibit request when OTA is complete. - Allows vehicle to return to sleep after detecting CAN traffic, for reduced battery drain. - Perimeter alarm duty cycle for horn and light aligned with non -US market requirements. (ECE-116)
SSM 52280
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E, 2022-2024 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B.
SANVol 2 Issue 1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.