Vehicle report

2017 FORD TRANSIT CONNECT

Compare every FORD TRANSIT CONNECT yearNHTSA and EPA records

Service bulletins

92 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

25N15 S1

Other

Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement

25N17

Other

Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation

SSM 54601

Service Bulletin/Repair Instructions

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

TSB 25-2570

Service Bulletin/Repair Instructions

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

SSM 54366

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

SSM 53040

Service Bulletin/Repair Instructions

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

TSB 24-2165

Service Bulletin/Repair Instructions

This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

SSM 52476

Service Bulletin/Repair Instructions

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

SSM 52335

Service Bulletin/Repair Instructions

For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

SAN-Vol1 I1

Service Bulletin/Repair Instructions

The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

SSM 51536

Service Bulletin/Repair Instructions

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

TSB 22-2066

Service Bulletin/Repair Instructions

Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.

SSM 50659

Service Bulletin/Repair Instructions

Some 2017-2022 Transit Connect/Transit/Explorer vehicles equipped with a fleet telematics global positioning system (GPS) and a connected human machine interface (HMI) radio (CHR) may experience concerns with rear camera zoom, wrong map matching or a blank display. If these concerns are present, it's likely to be a software issue caused by the audio control module (ACM) that can be remedied by updating the ACM software to the latest level with the FDRS application. If the update does not resolve the concern, refer to the Workshop Manual. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 22-2114

Service Bulletin/Repair Instructions

This article supersedes TSB 20-2047 to update the model years affected. Some 2013-2022 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.

SSM 50588

Service Bulletin/Repair Instructions

Some 2017-2022 Transit Connect/Transit/Explorer vehicles equipped with a fleet telematics global positioning system (GPS) and a connected human machine interface (HMI) radio (CHR) may experience concerns with rear camera zoom, wrong map matching or a blank display. If these concerns are present, it's likely to be a software issue caused by the audio control module (ACM) that can be remedied by the following: If the existing ACM software level is at H1BT-14G298-GS or higher, update the ACM software with the FDRS application or, if the ACM software level is H1BT-14G298-GR or lower, it cannot be updated and the ACM will need to be replaced with the latest level part number.

TSB 21-2379

Service Bulletin/Repair Instructions

Some 2014-2020 Transit Connect vehicles built on/or after 01-Feb-2013 may exhibit water dripping into the passenger front footwell. This may be due to an excessive gap in the heating, ventilation, and air conditioning (HVAC) case allowing water to drip from the case when the air conditioning (A/C) is operating. To correct the condition, follow the Service Procedure steps to reseal the HVAC case.

SSM 50067

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 50039

Service Bulletin/Repair Instructions

Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

TSB 21-2175

Service Bulletin/Repair Instructions

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

SSM 49821

Service Bulletin/Repair Instructions

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 21-2152

Service Bulletin/Repair Instructions

TSB 21-2033

Service Bulletin/Repair Instructions

Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.

TSB 20-2382

Service Bulletin/Repair Instructions

SSM 49210

Service Bulletin/Repair Instructions

Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

SSM 49086

Service Bulletin/Repair Instructions

Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

TSB 20-2255

Service Bulletin/Repair Instructions

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

SSM 48911

Service Bulletin/Repair Instructions

SSM 48908

Service Bulletin/Repair Instructions

Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

TSB 20-2087

Service Bulletin/Repair Instructions

Some 2015-2019 Transit vehicles equipped with a 3.2L engine, 2018-2020 F150 vehicles equipped with a 3.0L engine, 2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.

SSM 48619

Service Bulletin/Repair Instructions

SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

TSB 20-2047

Service Bulletin/Repair Instructions

Some 2013-2020 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.

SSM 48423

Service Bulletin/Repair Instructions

Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 48340

Service Bulletin/Repair Instructions

Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

SSM 48135

Service Bulletin/Repair Instructions

Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 48123

Service Bulletin/Repair Instructions

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

SSM 48053

Service Bulletin/Repair Instructions

Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

SSM 47976

Service Bulletin/Repair Instructions

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

SSM 47967

Service Bulletin/Repair Instructions

Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

SSM 47850

Service Bulletin/Repair Instructions

SSM 47875

Service Bulletin/Repair Instructions

Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.

SSM 47824

Service Bulletin/Repair Instructions

Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47749

Service Bulletin/Repair Instructions

Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

SSM 47711

Service Bulletin/Repair Instructions

Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

SSM 47703

Service Bulletin/Repair Instructions

Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.

SSM 47538

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

SSM 47519

Service Bulletin/Repair Instructions

Some 2016-2018 Escape vehicles built on or before 26-Aug-2018 and 2016-2018 Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM to the latest calibration using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 47444

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

tsb18-2179

Service Bulletin/Repair Instructions

This article supersedes TSB 18-2084 to update the Service Procedure. Some 2013-2018 Transit Connect vehicles built on 1-Jan-2013 and through 5-Jan-2018 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat. Follow the Service Procedure steps to correct the condition.

SSM 47397

Service Bulletin/Repair Instructions

Some 2016-2018 Escape/Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM using the appropriate Ford scan tool or equivalent release 110.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 47379

Service Bulletin/Repair Instructions

Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

SSM 47380

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

18L02

Service Bulletin/Repair Instructions

Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage

SSM 47211

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 47201

Service Bulletin/Repair Instructions

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.

SSM 47187

Service Bulletin/Repair Instructions

Some 2017-2018 Escape/Focus/Transit Connect vehicles equipped with remote start may exhibit the engine shut off after using the remote start function to start the vehicle with DTC P1594 stored in the BCM. If using the FordPass app, the app will tell the customer that the vehicle started successfully, but the customer observes that the vehicle did not start or started then shut off. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

SSM 47170

Service Bulletin/Repair Instructions

Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

SSM 47171

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.

SSM 47167

Service Bulletin/Repair Instructions

Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

TSB18-2084

Service Bulletin/Repair Instructions

Some 2013-2018 Transit Connect vehicles built on 9-Jan-2013 and through 5-Jan-2018 may exhibit a condition where the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable in need of adjustment. Follow the Service Procedure steps to correct the condition.

SSM 47100

Service Bulletin/Repair Instructions

Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.

SSM 47080

Service Bulletin/Repair Instructions

2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

SSM 47041

Service Bulletin/Repair Instructions

SSM 47009

Service Bulletin/Repair Instructions

The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

SSM 46947

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 46948

Service Bulletin/Repair Instructions

Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.

SSM 46949

Service Bulletin/Repair Instructions

SSM 46930

Service Bulletin/Repair Instructions

Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

SSM 46900

Service Bulletin/Repair Instructions

Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

SSM 46860

Service Bulletin/Repair Instructions

SSM 46861

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

SSM 46848

Service Bulletin/Repair Instructions

Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.

SSM 46834

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 46813

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.

SSM 46816

Service Bulletin/Repair Instructions

2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.

SSM 46702

Service Bulletin/Repair Instructions

Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

SSM 46527

Service Bulletin/Repair Instructions

For 2014-2017 Transit Connect Vehicles with a Taxi Conversion there is a 12-Pin block connector available for connecting the taxi spot lights to the main body harness. Service Part Number GU2Z-14S411-JA.

SSM 46486

Service Bulletin/Repair Instructions

SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

17B05

Service Bulletin/Repair Instructions

CERTAIN 2016-2017 MODEL YEAR TRANSIT CONNECT - FLOOR MATS INCOMPATIBLE WITH VINYL FLOOR.

SSM 46450

Service Bulletin/Repair Instructions

SOME VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

SSM 46439

Service Bulletin/Repair Instructions

SOME 2013-2017 TRANSIT CONNECT VEHICLES BUILT ON OR BEFORE 13-JAN-2017 MAY REQUIRE REPLACEMENT OF THE PANORAMIC ROOF SHADE. WHEN INSTALLING THE NEW ROOF SHADE THE WIRE HARNESS CONNECTOR FOR THE ROOF SHADE MODULE MAY NEED TO BE EXTENDED IN ORDER TO REACH THE NEW MODULE. FOLLOW THE RECOMMENDED SPLICING METHOD FOR EXTENDING THE HARNESS IN THE ON-LINE WIRING DIAGRAMS SECTION 5-1, CONNECTOR REPAIR PROCEDURES.

SSM 46332

Service Bulletin/Repair Instructions

REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

SSM 46321

Service Bulletin/Repair Instructions

SOME 2014-2017 TRANSIT CONNECT VEHICLES, MAY EXHIBIT A CONDITION THAT CAUSES THE BATTERY TO DISCHARGE. IF NORMAL BATTERY DRAIN DIAGNOSIS LEADS TO NO ISSUES, IT MAY BE CAUSED BY THE APPROACH LIGHTS ILLUMINATING EVERY TIME THE BODY CONTROL MODULE (BCM) RECEIVES A LOCK/UNLOCK SIGNAL OR OPENING ANY DOOR. IF THE DOOR REMAINS OPEN, THE LIGHTS WILL REMAIN ILLUMINATED FOR UP TO 10 MINUTES. IF THE VEHICLE WAS BUILT ON OR BEFORE 11-DEC-2016, REPROGRAM THE BCM TO THE LATEST CALIBRATION USING IDS RELEASE 103.05 AND HIGHER. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFT.COM. FOR ALL VEHICLES, ACCESS THE BCM CONFIGURATION PARAMETERS. SELECT MODULE PROGRAMMING, PROGRAMMABLE PARAMETERS, PERSONALITY, APPROACH LIGHT. CHOOSE DISABLED AND FOLLOW THE SCREEN PROMPTS TO COMPLETION. USE CAUSAL PART 14A068 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.

SSM 46295

Service Bulletin/Repair Instructions

TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

SSM 46293

Service Bulletin/Repair Instructions

SOME 2014-2017 TRANSIT CONNECT VEHICLES ARE EQUIPPED WITH CORNERING LAMPS. THE CORNERING LAMPS SHARE THE SAME BULB AS THE FOG LAMPS AND ILLUMINATE WHEN THE VEHICLE SPEED IS LESS THAN 25 MPH AND THE BODY CONTROL MODULE (BCM) RECEIVES A REQUEST FOR A TURN SIGNAL OR THE STEERING WHEEL IS TURNED GREATER THAN 35 DEGREES FROM CENTER. BEFORE DIAGNOSING A RIGHT OR LEFT FOG LAMP THAT MAY SEEM TO BE STUCK ON, TURN THE STEERING WHEEL BACK TO CENTER. IF THE LAMP GOES OFF, THE VEHICLE IS EQUIPPED WITH CORNERING LAMPS AND ARE WORKING AS DESIGNED. REFER TO THE WORKSHOP MANUAL SECTION 417-01 EXTERIOR LIGHTING.

TSB 16-0162

Service Bulletin/Repair Instructions

SOME 2014-2017 TRANSIT CONNECT VEHICLES MAY EXHIBIT AN INOPERATIVE LOW BEAM HEADLAMP BULB(S) DUE TO HEAT DAMAGE AT THE BULB CONNECTOR. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

SSM 46151

Service Bulletin/Repair Instructions

SOME 2016-2017 FORD AND LINCOLN VEHICLES EQUIPPED WITH SYNC 3 AND NAVIGATION MAY EXHIBIT A CONDITION IN WHICH THE SIRIUSXM TRAFFIC LISTING IS NOT LOADING BUT ALL REMAINING TRAVEL LINK FEATURES OPERATE PROPERLY. SIRIUSXM TRAFFIC IS ONLY AVAILABLE ON VEHICLES EQUIPPED WITH NAVIGATION, ONLY IN SELECT MARKETS AND REQUIRES AN ACTIVE SUBSCRIPTION TO SIRIUSXM TRAFFIC INFORMATION. IF SIRIUSXM TRAFFIC WILL NOT LOAD ATTEMPT THE FOLLOWING PROCEDURE. TURN THE IGNITION OFF, OPEN AND CLOSE THE DRIVERS DOOR, WAIT FOR 3 MINUTES, THEN DRIVE THE VEHICLE OUTSIDE TO OBTAIN A CLEAR VIEW OF THE SKY. SIRIUSXM TRAFFIC SHOULD RECOVER. IF SIRIUSXM TRAFFIC DOES NOT RECOVER CONTINUE TO MONITOR OASIS FOR FUTURE UPDATES. ENGINEERING IS AWARE OF THIS CONCERN AND NO COMPONENT REPLACEMENT OR ANY SOFTWARE RE-FLASHES SHOULD BE PERFORMED AT THIS TIME. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.

SSM 46140

Service Bulletin/Repair Instructions

SOME 2017 TRANSIT VEHICLES EQUIPPED WITH OPTIONAL HIGH CAPACITY UPFIT SWITCHES AND/OR AN AUXILIARY JUNCTION BOX MAY EXHIBIT AN INOPERATIVE AUXILIARY RELAY NUMBER 8, LOCATED IN AUXILIARY FUSE PANEL NUMBER 2 BEHIND THE GLOVE BOX. UPFIT SWITCH NUMBER 3 WILL BE INOPERATIVE ON VEHICLES EQUIPPED WITH HIGH CAPACITY UPFIT SWITCHES. ENGINEERING IS INVESTIGATING THE CONCERN. DEALERS WITH VEHICLES AFFECTED BY THIS ISSUE ARE ADVISED TO SUBMIT A GLOBAL CONCERN REPORT BY CLICKING THE REPORT A VEHICLE CONCERN LINK AT THE BOTTOM OF THE OASIS SCREEN AND INCLUDE THE NUMBER OF AFFECTED VEHICLES. MONITOR OASIS FOR FURTHER UPDATES.

SSM 46102

Service Bulletin/Repair Instructions

Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

SSM 46085

Service Bulletin/Repair Instructions

The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

TSB 16-0126

Service Bulletin/Repair Instructions

Some 2016-2017 Transit vehicles equipped with a 3.5L GTDI engine and built on or before 13-Sep-2016 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P130D and no related performance concern. An occasional spark knock noise may be noticed with this condition. Follow the Service Procedure steps to correct the condition.

SSM 46073

Service Bulletin/Repair Instructions

Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

SSM 46048

Service Bulletin/Repair Instructions

Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.