25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Vehicle report
2022 FORD TRANSIT CONNECT
Service bulletins
30 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
25E06
Other
Certain 2021-2023 Model Year Transit Connect Equipped with 2.0L Engine Powertrain Control Module (PCM) Reprogramming The affected vehicles have an emissions control system that might not control tailpipe emissions effectively
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
TSB 25-2550
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2092 to update model years. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Transmission slipping Harsh Engagements Clutch DTCs This may be due to worn needle bearings in the output planet carrier assembly.
25L02
Other
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
24B47 S1
Other
CERTAIN 2018-2024 MODEL YEAR VARIOUS VEHICLES — UPDATE SYNC SOFTWARE
SSM 53465
Service Bulletin/Repair Instructions
Some 2021-2024 Bronco Sport, 2020-2024 Escape/Corsair/Edge/Nautilus/Transit Connect and 2022-2024 Maverick vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color, this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
24B47
Service Bulletin/Repair Instructions
Certain 2018 - 2024 Model Year Various Vehicles Update SYNC Software In all the affected vehicles, due to an error in the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52410
Service Bulletin/Repair Instructions
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 52307
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51725
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51449
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51261
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 51228
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51131
Service Bulletin/Repair Instructions
Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 51120
Service Bulletin/Repair Instructions
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB-STO2022-002
Service Bulletin/Repair Instructions
This Service bulletin is related to the exhaust fan that we install on the roof. After seeing an increasing trend in warranty calls regarding leaks, we launched an investigation into the source of the leaks and found the exhaust fan seal to be the culprit. The repair procedure outlined below has been successfully tested and incorporated into our current production process. There are no safety risks involved rather unwanted water penetration into the van.
SSM 51011
Service Bulletin/Repair Instructions
Some 2018-2022 Ford and Lincoln vehicles equipped with the 8F35 transmission built on or before 16-Mar-2022 may exhibit transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01.
SSM 50873
Service Bulletin/Repair Instructions
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 50733
Service Bulletin/Repair Instructions
Some 2021 and 2022 Ford and Lincoln vehicles may experience a tire sidewall wavy/indentation appearance in the radial direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.
SSM 50659
Service Bulletin/Repair Instructions
Some 2017-2022 Transit Connect/Transit/Explorer vehicles equipped with a fleet telematics global positioning system (GPS) and a connected human machine interface (HMI) radio (CHR) may experience concerns with rear camera zoom, wrong map matching or a blank display. If these concerns are present, it's likely to be a software issue caused by the audio control module (ACM) that can be remedied by updating the ACM software to the latest level with the FDRS application. If the update does not resolve the concern, refer to the Workshop Manual. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-2114
Service Bulletin/Repair Instructions
This article supersedes TSB 20-2047 to update the model years affected. Some 2013-2022 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.
SSM 50588
Service Bulletin/Repair Instructions
Some 2017-2022 Transit Connect/Transit/Explorer vehicles equipped with a fleet telematics global positioning system (GPS) and a connected human machine interface (HMI) radio (CHR) may experience concerns with rear camera zoom, wrong map matching or a blank display. If these concerns are present, it's likely to be a software issue caused by the audio control module (ACM) that can be remedied by the following: If the existing ACM software level is at H1BT-14G298-GS or higher, update the ACM software with the FDRS application or, if the ACM software level is H1BT-14G298-GR or lower, it cannot be updated and the ACM will need to be replaced with the latest level part number.
SSM 50566
Service Bulletin/Repair Instructions
Some 2022 Ford and Lincoln vehicles may need to perform A/C leak detection diagnostics. The 2022 Workshop Manual (WSM), Section 412-00 for A/C leak detection diagnosis is incomplete and is in the process of being updated. At this time, Pinpoint Test AN of Section 412-00 in the 2022 F-150 WSM can be used temporarily for the service procedure and specifications. Use the correct vehicle specific removal and replacement sections as needed. A new labor operation 19700A45 has also been released to align with the new procedure.
SSM 50306
Service Bulletin/Repair Instructions
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.