26L01
Other
Customer Satisfaction Program 26L01 Certain 2018-2024 Model Year Various Vehicles 2.0L Panther Diesel Engine Timing Belt and Tensioner Interval Change
Vehicle report
2024 FORD TRANSIT
Service bulletins
81 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB 26-2349
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2415. Reason for update: To add production build dates of the right-side engine valve cover. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the positive crankcase ventilation (PCV) baffle which is part of the valve cover assembly.
SSM 55031
Service Bulletin/Repair Instructions
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
TSB 26-2309
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2241. Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
TSB 26-2263
Service Bulletin/Repair Instructions
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-2241
Service Bulletin/Repair Instructions
This bulletin supersedes 25-2587. Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54758
Service Bulletin/Repair Instructions
Some 2020-2026 Transit vehicle customers may request vehicle speed to be limited. Speed limiting can be configured to 65 mph (105 km/h), 70 mph (113 km/h), or 75 mph (121 km/h) using the Ford Diagnostic and Repair System (FDRS). It can be found under the toolbox tab labeled "PCM - Vehicle Speed Limiter Configuration". This capability has now been added to FDRS for the 2026 model year. This procedure is not warrantable. Do not submit a claim for this procedure.
SSM 54738
Service Bulletin/Repair Instructions
Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op
25N12
Other
Customer Satisfaction Program 25N12 Certain 2020-2025 Model Year Transit All-Wheel-Drive (AWD) Vehicles Transfer Case Replacement If Required After Dealer Evaluation
SSM 54719
Service Bulletin/Repair Instructions
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
SSM 54720
Service Bulletin/Repair Instructions
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
TSB 25-2587
Service Campaign
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
SSM 54674
Service Bulletin/Repair Instructions
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
TSB 26-2112
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-2059
Service Bulletin/Repair Instructions
This bulletin supersedes TSB 25-2423. Reason For Update: Replace the incorrect acronym SOWC with the correct acronym OWC. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SYNC-26.2.1.6.5.2 Transit
Over The Air
Quality improvements include: -Resolves SiriusXM disk memory usage
SSM 54589
Other
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various connectivity concerns with The Ford App Lincoln App including but not limited to: missing activation prompt pop-upon the vehicle's center display screen when attempting to activate vehicle through The Ford App Lincoln App, incorrect location global positioning system GPS reported through The Ford App Lincoln App, problems with remote commands being performed through The Ford App Lincoln App and or incorrect data information reported on The Ford App Lincoln App. These symptoms will be accompanied by diagnostic trouble code DTC B156D 89 in the TCU. This may be due to the accessory protocol interface module APIM software. To correct the condition, update the APIM software.
SSM 54592
Service Bulletin/Repair Instructions
For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
25B47 S1
Other
Certain 2021-2024 Model Year Transit All-Wheel-Drive (AWD) Vehicles Transfer Case Replacement
25L02
Other
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
SSM 54363
Service Bulletin/Repair Instructions
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
SSM 54313
Service Bulletin/Repair Instructions
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 54269
Service Bulletin/Repair Instructions
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
25B47
Other
Customer Satisfaction Program 25B47 Certain 2021-2024 Model Year Transit All-Wheel-Drive (AWD) Vehicles Transfer Case Replacement
TSB 25-2423
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TCU-25.2.5.9 Transit
Over The Air
Quality improvements include: -Includes a recovery mechanism for memory data in the Telematics Control Unit
SSM 54181
Service Bulletin/Repair Instructions
Some 2022-2025 E-Transit vehicles may exhibit an unsuccessful programmable module installation (PMI) and/or software updates on the GWM using the Ford Diagnosis and Repair System (FDRS) scan tool. FDRS may also show the GWM in the toolbox topology view as having diagonal lines through it, indicating that there is a data error for the GWM. This may be due to missing module configuration data in the Ford database. To correct this condition, select the envelope icon at the top right corner of FDRS, select "Refresh Vehicle Files", then click "Continue". Once the "Refresh Vehicle Files" completes, start a new FDRS session and then reattempt GWM programming. Engineering is working to correct this module data. The concern is expected to be resolved by October 2025.
TSB 25-2415
Service Bulletin/Repair Instructions
This article supersedes TSB 25-2361 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
ECG-25.2.5.7.1 Transit
Over The Air
"Quality improvements include: -Addresses unintended key off load battery usage caused by the Enhanced Central Gateway module staying awake"
SSM 54137
Service Bulletin/Repair Instructions
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
SU-6.14.0 Transit
Over The Air
25S49 Recall Remedy: -Infotainment software update to address frozen screens
SU-6.4.0 Transit
Over The Air
Quality improvements include: -Enhanced Central Gateway update to the latest software level
SSM 54116
Service Bulletin/Repair Instructions
Various 2019-2024 Ford and Lincoln vehicles equipped with SYNC 3 may experience a partially or fully black center display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.
SYNC-25.2.1.6.5 Transit
Over The Air
Quality improvements include: -Addresses key off load battery usage caused by Accessory Protocol Interface Module (APIM) remaining awake. Telematics Control Unit is updated to match the APIM software.
TSB 25-2361
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the PCV baffle which is part of the valve cover assembly.
TSB 25-2363
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Lack of air flow from inoperative blower motor * Open or damaged fuse F10 in the BJB This may be due to a damaged fuse F10 (40A) in the battery junction box (BJB). ** Model secton: all gas engine (non-BEV) ***** Legacy verbiage - will be removed after completing approvals ***** Some 2020-2024 Transit all gas engine (non-BEV) vehicles may exhibit a lack of air flow due to an inoperative heating, ventilation, and air conditioning (HVAC) blower motor. This may be due to a damaged fuse F10 (40A) in the battery junction box (BJB). To correct the condition, replace the fuse F10 (position 7 in the BJB). Replace the BJB and BJB harness only if it is required with the listed service replacement part.
SSM 54090
Service Bulletin/Repair Instructions
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
SU-6.2.0 Transit
Over The Air
Quality improvements include: -Enhanced compatibility between the Enhanced Central Gateway and Telematics Control Unit (TCU) for vehicles that use TCU as the source of GPS
SU-6.1.0 Transit
Over The Air
Quality improvements include: -Introduction of preventive measures to avoid network disconnections
25B31
Other
Certain 2024 Model Year Transit Electric Vehicles High Voltage Battery Array Inspection and Replacement On the affected vehicles, incomplete sealing of a cell in the high voltage battery may have occurred during the manufacturing process. Incomplete sealing of a high voltage battery cell may lead to an electrolyte leak, resulting in an isolation fault or low battery module voltage condition. Initially, the operator may observe a wrench light and will not experience any change to drivability. Over time, the condition may progress to a no-start condition, or reduced power with wrench and turtle warning lights. Eventually, the operator may experience a “Stop Safely Now” message followed by a loss of propulsion
SSM 53983
Service Bulletin/Repair Instructions
Some 2022-2025 Transit vehicles may experience an unsuccessful programmable module installation (PMI) on the body control module (BCM) using the Ford Diagnosis and Repair System (FDRS) diagnostic tool. This may be due to a software to hardware correlation issue. This correlation issue has been fixed on the Ford servers. To correct this condition, download and run the "BCM-Body Control Module Installation (PMI)" application using the FDRS scan tool. If the PMI fails with an error stating "check valid application failed" and the self test shows the BCM responds negatively (purple color coding), replace the BCM with service part number NK4Z-15604-E or NK4Z-15604-F. Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation numbers 12651D and 12651D4 if BCM replacement was not required, 12651D and 12651D5 if BCM replacement was required.
SSM 53966
Service Bulletin/Repair Instructions
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
TSB 25-2268
Service Bulletin/Repair Instructions
Some of the vehicles listed in the Model statement above may exhibit an illuminated brake warning lamp while driving through high altitude areas with diagnostic trouble code (DTC) P050F stored in the anti-lock brake system module (ABS). This may be due to the ABS software level.
SSM 53894
Service Bulletin/Repair Instructions
Some 2022-2025 Transit vehicles equipped with a 360 degree camera may exhibit one camera display inoperative with diagnostic trouble codes (DTCs) B12BE:31, B148E:31, B12BF:31 and B115E:31 stored in the image processing module B (IPMB). These DTCs will set when only one camera has the condition. Replacement and/or reprogramming of the IPMB will not resolve this condition. To properly identify which camera/circuit has the condition and requires repair, visually confirm which camera display is inoperative (grayed out/blank/blue). If the condition is intermittent, interview the customer to find out more details and/or review the DTCs stored in the IPMB. The DTC with a status byte of 2F (example: B12BF:31:2F) indicates which camera/circuit has the condition. Repair as necessary. Refer to the Workshop Manual (WSM), Section 413-13C.
SSM 53764
Service Bulletin/Repair Instructions
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
24P28
Other
Customer Satisfaction Program 24P28 Certain 2025 Model Year F-650/F-750, 2024 Model Year Super Duty, Transit and Escape Vehicles A/C Compressor Inspection
24B39
Other
CERTAIN 2020-2024 MODEL YEAR TRANSIT ALL-WHEEL-DRIVE (AWD) VEHICLES — ALL WHEEL DRIVE MODULE (AWDM) SOFTWARE UPDATE
25B01
Other
Certain 2024 Model Year F-150, Mustang, Expedition, Navigator, Transit, Super Duty, and 2025 Model Year Explorer vehicles, equipped a 10R80/10R100 Transmission. Transmission Assembly Replacement
24B80
Other
Certain 2024 Model Year Transit Vehicles Equipped with a 3.5L Duratec Engine Long Block Replacement. On all the affected vehicles, a casting concern resulted in a material void of the engine block deck face at the sealing joint between the engine timing chain case, and the exterior of the block.
SSM 53327
Service Bulletin/Repair Instructions
Some 2020-2024 Transit vehicles built on 01-Aug-2019 and through 23-Oct-2024 may exhibit a lack of power steering assist on initial engine start-up with diagnostic trouble code (DTC) U3000:49 stored in the power steering control module (PSCM).
SSM 53323
Service Bulletin/Repair Instructions
All Transit accessory stick-on keyless entry keypads come with a wallet card containing the master code.
SSM 53305
Service Bulletin/Repair Instructions
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
SSM 53168
Service Bulletin/Repair Instructions
Some 2024 Transit vehicles may exhibit a windshield washer fluid leak at the washer pump built on or before 22-Jul-2024.
SSM 53088
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
24N15
Service Bulletin/Repair Instructions
In the affected vehicles, over time, the Electric Vacuum Pump (EVP) may stop functioning due to broken wires internal to the pump. This may result in the driver experiencing a hard brake pedal feel and perceived reduction in brake response
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
24U10
Service Bulletin/Repair Instructions
In some of the affected vehicles with low time in service, the Air Conditioning (A/C) compressor may experience an internal failure that can cause loss of A/C performance or function.
SSM 52820
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off.
SSM 52783
Service Bulletin/Repair Instructions
Some 2023-2024 Transit vehicles may require the front bumper inner park aid sensor (15K859) to be replaced in service. The service part number called out in the parts catalog for the sensors, NU5Z-15K859-AQPTM, is incorrect. If it is necessary to replace the front bumper inner parking aid sensors, order part number JU5Z-15K859-APTM.
SSM 52722
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
SSM 52704
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
SSM 52675
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
SSM 52653
Service Bulletin/Repair Instructions
Some 2023-2024 Transit vehicles may experience an inoperative driver or passenger power window. In these vehicles, the power window motor is equipped with thermal protection against current increase or excessive operation of the switch. Once the protection is activated, the power window motor will automatically reset after approximately 20 seconds of window motor rest time. Before performing any diagnostic or repair, allow any inoperative window to rest for over 20 seconds and then retest its operation. The Workshop Manual (WSM) pinpoint test has been updated to reflect the thermal protection feature is present in this system.
SSM 52654
Service Bulletin/Repair Instructions
Some 2023-2024 Transit vehicles equipped with a park aid module (PAM) may erroneously exhibit a Not Responding message in FDRS due to the PAM not being assigned to the correct network. Prior to diagnosing, verify the vehicle is equipped with a PAM. Units with 360 degree camera do not have a PAM. For units with SYNC 4, the PAM communicates on high speed channel 2 (HS2). For units without SYNC 4, the PAM communicates on high speed channel 1 (HS1).
SSM 52596
Service Bulletin/Repair Instructions
2024-2024 Tranist- Keyless Entry Keypad and Master Code Retrieval. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in a plastic bag that is located in instrument panel pocket behind the steering wheel. During vehicle delivery, the card should be handed to the vehicle's owner. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users.
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SAN Vol2 Issue 4
Other
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information
SSM 52574
Service Bulletin/Repair Instructions
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
SSM 52548
Service Bulletin/Repair Instructions
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 52483
Service Bulletin/Repair Instructions
Some 2018-2019 Explorer and 2018-2024 Transit/F-150/Expedition/Navigator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.
SSM 52448
Service Bulletin/Repair Instructions
2015-2024 Transit and 2023-2024 Transit Trail vehicles equipped with DRW have a high mount rear marker lamp that does not illuminate with the stop lamps. This lamp assembly may appear to be a stop lamp but is intended to illuminate with the parking lamps only. This information is available in Workshop Manual Section 417-01. The JDDAB feature code description, found under OASIS additional information, is common between single rear wheel and DRW vehicles, and incorrectly reflects stop functionality when applied to DRW units.
TSB 24-2099
Service Bulletin/Repair Instructions
This article supersedes TSB 22-2444 to add 2024 model year vehicles. Some 2015-2024 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (only), and U-joints at the transmission flange and rear driveshaft may experience a boom/hum/moan noise from the rear while driving. This noise is most noticeable at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio 121-128 km/h (75-80 mph) for 3.73 axle ratio 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise may also be present to a lesser degree at roughly half of the noted speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs.
SSM 52370
Service Bulletin/Repair Instructions
Some 2023-2024 F-150 and 2024 Bronco/Transit vehicles may exhibit Apple Carplay Bluetooth connectivity concerns. This may be due to the accessory protocol interface module (APIM) software. To correct this concern, perform a soft reset by pressing the Power and Seek Foward buttons for 5 seconds, or use the SYNC Module Reset function of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G670 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52345
Service Bulletin/Repair Instructions
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 52335
Service Bulletin/Repair Instructions
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
24G02
Service Bulletin/Repair Instructions
Optional Product Improvement 24G02 Certain 2022-2024 Model Year Transit Battery Electric Vehicles (BEV) - Off-Board Charger Controller (OBCC) Software Update
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 52280
Service Bulletin/Repair Instructions
Some 2021-2024 Mustang Mach-E, 2022-2024 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B.
SANVol 2 Issue 1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.