Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-BD-001G-1 TSB
Service Bulletin/Repair Instructions
This bulletin provides repair information for the dark chrome trim when stains are present. Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.
25-01-024G-1 TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Connected Car Services functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.
25-GI-009G
Service Bulletin/Repair Instructions
Certain Genesis vehicles may experience an inoperable horn from moisture or carbonization at the contact point. This bulletin provides a guide to inspect and replace the horns.
25-BD-001G TSB
Service Bulletin/Repair Instructions
This procedure provides repair information for the dark chrome trim when stains are present. Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.
24-DS-001G-1 TSB
Service Bulletin/Repair Instructions
Certain GV70 (JK1, JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a hum or whine noise condition from the rear differential at certain speeds. This bulletin describes the procedure to inspect the vehicle for the hum or whine noise and if necessary to tighten the rear differential lock nut first. If the hum or whine noise remains, then replace the rear differential or other driveline components as necessary.
24-DS-003G
Service Bulletin/Repair Instructions
This bulletin provides information to inspect and replace the front or rear wheel bearing hub assemblies for all Genesis vehicles. This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.
23-AT-007G
Service Bulletin/Repair Instructions
When servicing an 8-speed automatic transmission vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure and, if necessary, replace the E-module.
23-01-037HG
Service Bulletin/Repair Instructions
Certain 2017-2020MY G80 vehicles may exceed evaporative emissions standards due to Onboard Refueling Vapor Recovery (ORVR) system. To correct this symptom, install an auxiliary canister assembly between the canister and Canister Close Valve (CCV).
23-01-037G
Service Bulletin/Repair Instructions
Certain 2017-2020MY G80 vehicles may exceed evaporative emissions standards due to Onboarding Refueling Vapor Recovery (ORVR) system. To correct this symptom, install an auxiliary canister assembly between the canister and Canister Close Valve (CCV).
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-AT-001G
Service Bulletin/Repair Instructions
When servicing a vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch.
23-BD-002G
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.
21-AT-015G
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transmission for the following Incorrect Ratio DTC (transmission clutch slipping more than 200 rpm in gear).
21-FL-003G
Service Bulletin/Repair Instructions
This TSB provides consolidated diagnosis and repair information, currently in the shop manual, to address DTC U0109 / U010900 related to a communication error with the Fuel Pump Control Module (FPCM).
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-01-020G
Service Bulletin/Repair Instructions
This bulletin provides information related to the ECM(Engine Control Module) software update for G80/G90 with 5.0L GDI engine equipped vehicles. This updates the software logic dealing with OBD communication test.
21-BD-001G
Service Bulletin/Repair Instructions
Genesis applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-DS-002G
Service Bulletin/Repair Instructions
The bulletin describes the procedure to measure and set propeller shaft angles to optimize driveline vibration performance on certain 2019-2020MY 3.8L AWD G80 (DH) vehicles.
21-AT-012G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. ï· Before replacing an automatic transmission (Pages 2~3): Input the data from the new transmission into the TCU using the GDS. ï· Before replacing a TCU (Pages 4~6): Back up the oil pressure data from the old TCU into the GDS and then transfer the data to the new TCM.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-013HG
Service Bulletin/Repair Instructions
Certain Genesis G80 and G90 vehicles may experience the Shift By Wire (SBW) system slipping into Neutral when shifting from Reverse to Drive or Drive to Reverse. Replace the electronic shifter with a new shifter that has a production date of 6/2/17 or newer to resolve this condition.
20-BD-009G
Service Bulletin/Repair Instructions
Some vehicles may experience seat noise and/or possible wobble movement from the seat bottom when the vehicle is turning. This bulletin describes the procedure to install an e-ring clip to the tilt pipe housing on the front seat.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-EE-002H(1)
Service Bulletin/Repair Instructions
This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.
20-BD-003G
Service Bulletin/Repair Instructions
Certain 2019-2020 G80 (DH) vehicles may have a condition where the seat backboard comes loose. This bulletin describes the procedure to replace the seat backboard clip.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
19-BE-017G
Service Bulletin/Repair Instructions
Certain vehicles (listed below) equipped with the HomeLink5 (Two Way Communication) mirror may experience programming and operating difficulties with the home garage system. This bulletin provides information related to some of the possible symptoms.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-BD-004G-1
Service Bulletin/Repair Instructions
Certain 2019-2020 G80 (DH) vehicles may have a condition where the seat backboard comes loose. This bulletin describes the procedure to replace the seat backboard clip.
19-AT-023G
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-BD-006G
Service Bulletin/Repair Instructions
Some vehicles may experience seat noise from seat bottom when vehicle is turning. This bulletin describes the procedure to install an e-ring clip to the tilt pipe housing on the front seat.
19-01-025HG
Service Bulletin/Repair Instructions
This bulletin provides information related to an ECM (Engine Control Module) software diagnostics logic update for DTC P2067 - ?Fuel Level Sensor B (Main) Circuit ? Low?. There are no drivability symptoms with this DTC.
19-BD-004G
Service Bulletin/Repair Instructions
This bulletin describes the procedure to replace the seat backboard clip. Some vehicles may experience the seat backboard coming loose.
19-AT-014G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to diagnose an 8-speed automatic transaxle with a harsh and/or delayed shift.
19-AT-012G
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-007G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. ï· Before replacing an automatic transmission: Input the data into the TCU using the GDS. ï· Before replacing a TCU: Back up the oil pressure data from the old TCU into the GDS and then transfer the data to the new TCM.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-AT-008G
Service Bulletin/Repair Instructions
When servicing a vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch.
18-01-006-G
Service Bulletin/Repair Instructions
This bulletin provides information related to an ECM (Engine Control Module) software update for OBD (On Board Diagnostics) logic improvement. The Fuel System Readiness settings logic has been updated.
18-01-005-G
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and repair brake pulsation on dealer stock vehicles only. The procedure described should be performed just prior to retail sale.