Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
26-DS-001G TSB
Service Bulletin/Repair Instructions
Some GV70 (JK1, JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a hum or whine noise condition from the rear differential at certain speeds. This bulletin describes the procedure to inspect the vehicle for the hum or whine noise and, if necessary, to tighten the rear differential lock nut to specification. If the hum or whine noise remains after tightening the lock nut, then this bulletin provides instructions to replace the rear differential or other driveline components as necessary.
26-HA-002G TSB
Service Bulletin/Repair Instructions
Some Genesis vehicles (listed below) equipped with Lambda-III 3.5T-GDI engines may exhibit reduced heater performance due to engine coolant deposits clogging the heater core. This bulletin provides instructions to verify the concern and to replace the front and rear heater core (if applicable).
26-GI-002G TSB
Service Bulletin/Repair Instructions
This bulletin provides information related to the navigation and head unit software changes introduced in the 2026 1st Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.
26-EE-003G TSB
Service Bulletin/Repair Instructions
Some vehicles may exhibit difficulty starting in cold weather. This bulletin provides the procedure to perform an inspection on the starter magnetic switch for potential freezing and, if necessary, replace the starter magnetic switch (solenoid) assembly.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
26-AD-001G
Service Bulletin/Repair Instructions
Some 2020MY and newer vehicles equipped with a front view camera may illuminate certain warning lights and trigger DTC C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: • If the front camera is not properly installed and is completely or partially detached. • In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). • Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).
25-BE-025G TSB
Service Bulletin/Repair Instructions
Certain vehicles equipped with Premium Gen6 Navigation head units may exhibit issues with Genesis Connected Services, navigation, voice recognition, and Bluetooth functionality. In some cases, the home screen may display applications not intended for the U.S. market. This TSB provides the procedure to update the Premium Gen6 Navigation software to address these conditions.
914G OL
Service Campaign
This notice is being sent to you as our records indicate you may have previously received an important Service Campaign notice for Genesis Campaign Number 914G. “Genesis is conducting a service campaign to update the Engine Control Module (ECM) Software for certain 2021 – 2024 model year G80, certain 2022 – 2025 model year GV70, and certain 2021 – 2024 model year GV80 vehicles equipped with 2.5 T-GDI engines.” Genesis has revised the list of vehicles impacted by Campaign 914G and determined that your vehicle IS NOT affected by this service campaign.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-BE-020G TSB
Service Bulletin/Repair Instructions
This bulletin provides information related to the changes introduced in the 2025 1st Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.
25-ST-001G TSB
Service Bulletin/Repair Instructions
Some vehicles may exhibit a rubbing type noise when turning the steering wheel. Follow the procedure in this TSB to inspect the source of the noise and, if necessary, replace the Steering Shaft Dust Cover.
25-01-051 OL
Service Campaign
Genesis has become aware that some vehicles may illuminate the Check Engine Light indicator as a result of detected engine misfires.
25-01-051G DN
Service Campaign
Certain G80 (RG3), GV70 (JK1/JK1A), and GV80 (JX1) vehicles equipped with Theta III 2.5L T-GDI engine may illuminate the Check Engine Light as a result of misfire DTCs P0300, P0301, P0302, P0303, or P0304. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
25-01-051G TSB
Service Campaign
Certain G80 (RG3), GV70 (JK1/JK1A), and GV80 (JX1) vehicles equipped with Theta III 2.5L T-GDI engines may illuminate the Check Engine Light as a result of misfire DTCs P0300, P0301, P0302, P0303, or P0304 during cold start. This bulletin provides instructions for updating the Engine Control Module (ECM).
25-HA-002G TSB
Service Bulletin/Repair Instructions
Certain Genesis vehicles may experience insufficient cooling in the cabin due to leakage at the evaporator core. This bulletin provides instructions to inspect the A/C system for leaks and replace the evaporator core, if necessary.
25-BE-014G TSB
Service Bulletin/Repair Instructions
Certain G80 (RG3) and G80 Electrified (RG3 EV) vehicles may have an inoperable horn due to an exposure to moisture from the horizontal mounting position. This bulletin provides instructions to replace and vertically mount the horns and add a LH extension cable for the LH horn.
25-BD-001G-1 TSB
Service Bulletin/Repair Instructions
This bulletin provides repair information for the dark chrome trim when stains are present. Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.
25-BE-002G TSB
Service Bulletin/Repair Instructions
This bulletin provides information related to the changes introduced in the 2024 2nd Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater and updated by USB. The NAU website is https://update.genesis.com/US/EN/navigationUpdate. For certain models equipped with a relevant Genesis Connected Services (GCS) package, the software may be downloaded and applied via OTA update.
25-01-024G-1 TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Connected Car Services functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.
25-GI-009G
Service Bulletin/Repair Instructions
Certain Genesis vehicles may experience an inoperable horn from moisture or carbonization at the contact point. This bulletin provides a guide to inspect and replace the horns.
25-BE-007G TSB
Service Bulletin/Repair Instructions
Certain 2021-2023MY GV80 (JX1), 2022-2023MY GV70 (JK1), 2021-2023MY G80 (RG3) and 2023MY G80 Electrified (RG3 EV) vehicles may exhibit a warning light with DTC C162078 due to improper detection of steel structures. Advanced Driver Assistance System (ADAS) functions are not affected due to this condition. Follow the procedure in this bulletin to update the front radar unit and perform all related adjustments according to shop manual.
25-01-024G EM
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Genesis Connected Service functions. This may be due to an irregular disconnection on Verizon's communication network.
25-01-024G TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Connected Car Services functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection by resetting the AVN unit.
25-BD-001G TSB
Service Bulletin/Repair Instructions
This procedure provides repair information for the dark chrome trim when stains are present. Some stains may occur from hard water or cleaning chemicals used during a car wash. Follow the procedures below to replace the affected dark chrome moldings.
24-DS-001G-1 TSB
Service Bulletin/Repair Instructions
Certain GV70 (JK1, JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a hum or whine noise condition from the rear differential at certain speeds. This bulletin describes the procedure to inspect the vehicle for the hum or whine noise and if necessary to tighten the rear differential lock nut first. If the hum or whine noise remains, then replace the rear differential or other driveline components as necessary.
24-HA-001G
Service Bulletin/Repair Instructions
Certain Genesis vehicles (listed below) equipped with Lambda-III 3.5T-GDI engines may exhibit reduced heater performance due to engine coolant deposits clogging the heater core. This bulletin provides instructions to verify the concern and to replace the front and rear heater core (if applicable).
24-01-044G
Service Campaign
This message provides instructions for vehicles experiencing an incomplete Over-The-Air (“OTA”) AVN software update.
24-DS-003G
Service Bulletin/Repair Instructions
This bulletin provides information to inspect and replace the front or rear wheel bearing hub assemblies for all Genesis vehicles. This procedure is applicable when noise (whirring, roaring, grinding, rumbling, etc.) is present which gets louder when driving with more speed.
24-DS-001G
Service Bulletin/Repair Instructions
Certain GV70 (JK1 and JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a hum or whine noise condition from the rear differential at certain speeds. This bulletin describes the procedure to inspect the vehicle for the hum or whine noise and if necessary to tighten the rear differential lock nut first. If the hum or whine noise remains, then replace the rear differential or other driveline components as necessary.
23-DS-004G-1
Service Bulletin/Repair Instructions
Certain GV70 (JK1 and JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a noise condition from the rear differential at certain speeds while accelerating or decelerating. This bulletin describes the procedure to inspect the vehicle for noise and if necessary to tighten the lock nut or if necessary replace the differential.
23-EE-013G
Service Bulletin/Repair Instructions
This bulletin is issued to provide the extended battery diagnosis procedure using GDS. This battery diagnosis function displays the various battery-related faults such as: ⢠Internal short circuit ⢠Battery deterioration ⢠Malfunction of electronic parts ⢠Insufficient battery charge ⢠Normal battery ⢠Charging defect Battery diagnosis uses the battery sensor history saved for the last 30 days and ICU diagnostic communication to track battery state of charge (SOC) and current parasitic draw history.
23-ST-004G-1
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect the steering universal joint dust cover for noise, and if necessary, apply grease on certain Genesis vehicles.
23-DS-004G
Service Bulletin/Repair Instructions
Certain GV70 (JK1 and JK1A), GV80 (JX1) and G80 (RG3) vehicles may have a noise condition from the rear differential at certain speeds while accelerating or decelerating. This bulletin describes the procedure to inspect the vehicle for noise and if necessary to tighten the lock nut or if necessary replace the differential.
23-BD-014G
Service Bulletin/Repair Instructions
This bulletin provides instructions on how to service the panoramic sunroof on certain G80 (RG3) vehicles that experience creaking or rattling noises while driving on uneven roads.
23-BD-013G
Service Bulletin/Repair Instructions
This bulletin provides information to address difficultly with opening of the center console armrest storage on certain G80 (RG3) vehicles. The foam pad attached to the release button may interfere with its normal opening function. Follow the procedure in this bulletin to remove the foam pad and allow for easier opening of the center console armrest storage.
23-AT-007G
Service Bulletin/Repair Instructions
When servicing an 8-speed automatic transmission vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure and, if necessary, replace the E-module.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-ST-004G
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect the steering universal joint dust cover for noise, and if necessary, apply grease on certain Genesis vehicles.
23-AT-001G
Service Bulletin/Repair Instructions
When servicing a vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch.
23-BD-002G
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly.
22-01-060G
Service Bulletin/Repair Instructions
Certain 2021-2022MY Genesis G80 (RG3) vehicles may have coolant leakage from the radiator reservoir tank. Follow the procedure outlined in this bulletin to inspect the radiator reservoir tank, and if necessary, replace it with a new part.
22-FL-001G
Service Bulletin/Repair Instructions
This bulletin provides information related to the ECM(Engine Control Module) software update for 3.5L GDI engine equipped vehicles that experience check engine light, no drivability issue, and with either of the following DTC found stored in the ECM: ⢠P2096 - Post Catalyst Fuel Trim - System Too Lean (Bank 1). ⢠P2098 - Post Catalyst Fuel Trim - System Too Lean (Bank 2).
22-01-009G
Service Bulletin/Repair Instructions
This bulletin describes the procedure to replace the AMP ground side coil and coil and capacitor for certain vehicles exhibiting brown foam discoloration of the sponge pad in the rear glass antenna.
21-AT-015G
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transmission for the following Incorrect Ratio DTC (transmission clutch slipping more than 200 rpm in gear).
21-01-058G
Service Bulletin/Repair Instructions
Certain 2021MY Genesis G80 (RG3) vehicles may have coolant leakage from the radiator reservoir tank. Follow the procedure outlined in this bulletin to inspect the radiator reservoir tank, and if necessary, replace it with a new part.
21-01-029G-2
Service Bulletin/Repair Instructions
This bulletin provides the procedure to inspect, and if necessary adjust the headlight aim on some 2021 MY Genesis G80 (RG3) vehicles equipped with Light Emitting Diode (LED) headlamps. The adjustment can help improve headlamp focus and reduce glare from the headlights to oncoming traffic.
21-01-029G-1
Service Bulletin/Repair Instructions
This bulletin provides the procedure to inspect, and if necessary adjust the headlight aim on some 2021 MY Genesis G80 (RG3) vehicles equipped with Light Emitting Diode (LED) headlamps. The adjustment can help improve headlamp focus and reduce glare from the headlights to oncoming traffic.
21-01-029G
Service Bulletin/Repair Instructions
This bulletin provides the procedure to inspect, and if necessary adjust the headlight aim on some 2021 MY Genesis G80 (RG3) vehicles equipped with Light Emitting Diode (LED) headlamps. The adjustment can help improve headlamp focus and reduce glare from the headlights to oncoming traffic.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BD-001G
Service Bulletin/Repair Instructions
Genesis applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
21-AT-012G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. ï· Before replacing an automatic transmission (Pages 2~3): Input the data from the new transmission into the TCU using the GDS. ï· Before replacing a TCU (Pages 4~6): Back up the oil pressure data from the old TCU into the GDS and then transfer the data to the new TCM.
19-BE-017G
Service Bulletin/Repair Instructions
Certain vehicles (listed below) equipped with the HomeLink5 (Two Way Communication) mirror may experience programming and operating difficulties with the home garage system. This bulletin provides information related to some of the possible symptoms.
19-AT-023G
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-014G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to diagnose an 8-speed automatic transaxle with a harsh and/or delayed shift.
19-AT-012G
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-007G
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. ï· Before replacing an automatic transmission: Input the data into the TCU using the GDS. ï· Before replacing a TCU: Back up the oil pressure data from the old TCU into the GDS and then transfer the data to the new TCM.
19-AT-008G
Service Bulletin/Repair Instructions
When servicing a vehicle with a âCheck Engine lightâ and any of the DTCs listed below, follow the Service Procedure to replace the related solenoid and E-module or park position switch.