17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC4696E
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable. E version update is to add administrative details.
060309004N
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIC4696D
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable.
060309004M
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
PIC4696C
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco Theft Lock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
06-03-09-004I
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP4138P
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
16NA260
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
PIT3046G
This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.
PIC4696B
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIP5346
This Preliminary Information communication provides information to the technician about cooler line fittings that come with the 4T65E General Motors remanufactured transmission may not be the same as Original equipment manufacturer quick connect verses inverted flare. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC4696A
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIP5340
This Preliminary Information communication provides information to the technician about vehicle that after a transmission or torque converter replacement the vehicle may have a harsh 1-2 upshift and the Check Engine Light or Service Engine Soon indicator is illuminated. If you have duplicated the customer?s concern and found Diagnostic Trouble Code P0894 or P1870 set in the Transmission Control Module please contact General Motors Technical Assistance Center.
PIT3227L
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP4404F
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
06-03-09-004G
This technical bulletin adds the 2016 model year to repair information for lubricating the rear leaf springs to correct a customer concern for a squeak noise from rear of vehicle.
PIP5280
This Preliminary Information communication provides information to the technician about vehicles that may have a buzz noise at idle after fuel pressure regulator replacement. Technician will need to gain access to the fuel pump. After gaining access to the fuel pump check the power and ground for voltage drop with the key in the off from the fuel pump to the battery post. Technician should also check the pin fit and terminal drag. Technician may replace the fuel pump connector with the updated part using the latest version service bulletin 04-06-04-088C. Technician should inspect voltage drop points at the UBEC, fuel pump relay, ground at the frame and the battery cable grounds. If excessive resistance is found at the crimps, replace the crimp n seal splice sleeves for the affected circuits. If the circuits do not have high resistance replace the regulator using part number 19236428.
PIT3227K
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PI02003D
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing .
PIT3098E
This Preliminary Information communication provides information to the technician about vehicles that have a lean to the left or right. Technician will need to measure fender wheel-opening heights, front and rear, to quantify vehicle lean. Fender wheel-opening heights are related to, but distinct from, trim height. The front wheel-opening height is known as P height, and the rear wheel-opening height is known as R height. Adjust and heights that are out of specification. After all adjustments are done, perform a front-end alignment and check headlight aim.
13-05-22-001D
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
13-05-22-001C
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
06-03-09-004F
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension.
13-05-22-001B
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
PI02003C
This preliminary bulletin provides a diagnostic tip to install a temporary dowl rod to perform an alignment.
G-197151
00064H - SPECIAL COVERAGE (REVISED PART INFORMATION). SOME CUSTOMERS MAY EXPERIENCE A FAILURE OF THE ELECTRONIC DIESEL FUEL INJECTION PUMP. THIS SPECIAL POLICY APPLIES ONLY TO ELECTRONIC DIESEL-FUEL INJECTION PUMP REPAIRS AND/OR REPLACEMENT AS A RESULT OF INJECTION PUMP FAILURE. THIS SPECIAL COVERAGE DOES NOT COVER: GLOW PLUGS, TURBOCHARGER WEAR, LOW COMPRESSION ENGINES OR PCM/PCM WIRING CONDITIONS.
Recalls
Vehicle Recalls
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
13-05-22-001A
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
13-05-22-001
This informational bulletin provides information on brake line kits now available and how to service them on vehicle.
130089009
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIP4404E
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
PIP4138N
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
06-03-09-004E
This informational bulletin provides information for Squeak Noise from Rear of Vehicle Condition.
PI0969
This preliminary informational bulletin provides information on High Oil Pressure on Startup After Engine Replacement Concern.
01-08-49-017B
This technical bulletin provides a revision of 01-08-49-017A to add new pricing information and payment terms.
PIT3227H
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP4138M
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT3665C
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
SB-06-02-32-013B
SAAB/HUMMER/GM: DIAGNOSTIC TIPS/RECOMMENDATIONS WHEN POWER STEERING PUMP REPLACEMENT IS NECESSARY. ANALYSIS OF RETURNED POWER STEERING (PS) PUMPS THAT HAD BEEN REPLACED FOR NOISE, NO POWER ASSIST, NO OR LOW PRESSURE AND LEAKING CONDITIONS HAS INDICATED A HIGH NUMBER OF NO TROUBLE FOUND RESULTS. ALL 1997-2010 VEHICLES AND LIGHT TRUCKS; 2010 AND PRIOR HUMMERS H2/H3 AND SAAB 9-7X VEHICLES. *PE
000730022B
A NO REVERSE, NO SECOND GEAR, OR NO FOURTH GEAR CONDITION. *TT UPDATED *EH
010605003
VIBRATION OR RATTLE-TYPE NOISE COMING FROM THE EXHAUST SYSTEM AT IDLE WITH ENGINE RPMS BETWEEN 613 AND 712. *TT THIS BULLETIN REPLACED 01-06-05-003 DATED 07/01/2001. *TT
000604003B
ROUGH IDLE AFTER START, AND/OR A SERVICE ENGINE SOON (SES) LIGHT. VARIOUS MODELS INCLUDING THE 1995 CHEVROLET AND GMC S/T MODELS. *TT
00064C
A FAILURE OF THE ELECTRONIC DIESEL FUEL INJECTION PUMP, LEAKING TO COMPLAINTS OF POOR PERFORMANCE OR FUEL ECONOMY, HARD / NO STARTS, HESITATION, AS WELL AS ILLUMINATION OF THE SERVICE ENGINE SOON LIGHT. *TT
00064B
SOME CUSTOMERS MAY EXPERIENCE A FAILURE OF THE ELECTRONIC DIESEL FUEL INJECTION PUMP. *JG
000601023A
INFORMATION USED WHEN DIAGNOSING NOISE CONDITIONS SUCH AS ENGINE RATTLE NOISE, SPARK KNOCK AT 2000 - 2500 RPM RANGE, UNDER A MODERATE TO HEAVY LOAD WITH A WARMED UP ENGINE. *TT
000604003A
SOME CUSTOMERS MAY COMMENT ON ROUGH IDLE AFTER START UP, ESPECIALLY AFTER SETTING OVERNIGHT. *TT
99066D
SOME OWNERS MAY EXPERIENCE A SERVICE ENGINE SOON LIGHT, MISFIRE, ROUGH IDLE ORHARD START DUE TO A DEPOSIT BUILD-UP ON THE SEQUENTIAL CENTRAL PORT FUEL INUJECTOR (SCPI) POPPET VALVE(S). *TT
010730023
SOME OWNERS WITH VEHICLES BUILT BEFORE JANUARY 15,1999 MAY COMMENT ON A HARSH 1-2 UPSHIFT AND MAY ALSO HAVE A CHECK ENGINE LIGHT. *ET
010730021
THIS TECHNICAL SERVICE BULLETIN STATES THAT TECHNICIANS MAY EXPERIENCE DIFFICULTY IN REMOVING THE CONNECTORS FROM THE PARK / NEUTRAL POSITION SWITCH, USUALLY WHEN TRYING TO REMOVE THE SWITCH DURING TRANSMISSION SERVICE. *TT
010730012
INFORMATION PERTAINING TO THE NEW CONTROL VALVE BODY, SPACER PLATE AND GASKETS FOR THE 4L60-E AUTOMATIC TRANSMISSION. *TT
00148
SERVICE ENGINE SOON LIGHT, MISFIRE, ROUGH IDLE, OR HARD START DUE TO A DEPOSIT BUILD-UP ON THE SEQUENTIAL CENTRAL PORT FUEL INJECTOR (SCPI) POPPET VALVE(S). THE DEPOSIT BUILD-UP MAY CAUSE INJECTOR POPPETS TO STICK CLOSED. *TT
99066C
SOME OWNERS OF 1996 - 1998 MODEL YEAR S/T, M/L, C/K, G, P AND W4 TRUCKS, THAT ARE REGISTERED IN CALIFORNIA, EQUIPPED WITH 4.3L, 5.0L OR 5.7L ENGINE, AND CALIFORNIA EMISSIONS, MAY EXPERIENCE A SERVICE ENGINE SOON LIGHT, MISFIRE, ROUGH IDLE OR HARD START DUE TO A DEPOSIT BUILD-UP ON THE SEQUENTIAL CENTRAL PORT FUEL INJECTOR (SCPI) POPPET VALVE(S). *TT
000604045
EXPERIENCING AN ENGINE TICKING SOUND COMING FROM THE ENGINE COMPARTMENT WHILE THE VEHICLES IS BEING DRIVEN. *TT
99066B
SOME OWNERS MAY EXPERIENCE A SERVICE ENGINE SOON LIGHT, MISFIRE, ROUGH IDLE OR HARD START. **MR
000604014
SOME CUSTOMERS MAY COMMENT ON HARD, NO, OR SLOW START, BACKFIRE OR KICKBACK DURING CRANK / START, GRINDING OR UNUSUAL NOISES DURING CRANK, DIAGNOSTIC TROUBLE CODE P0338. *TT
000604002
SUBJECT REGARDING A HARD, NO START OR EXCESSIVE GRAY OR WHITE SMOKE CONDITION ON START UP AFTER RECENT GLOW PLUG REPLACEMENT. *TT
000604003
SOME CUSTOMERS MAY COMMENT ON ROUGH IDLE AFTER START UP, AND / OR A SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED. *TT
990730013
SOME CUSTOMERS MAY COMMENT ABOUT THE SERVICE ENGINE SOON LIGHT ILLUMINATING. *TT
990601003
CUSTOMER MAY COMMENT ON ENGINE KNOCKING NOISE. *TT
861008
CONCERNS ABOUT A LOOSE SIDE SWING OUT WINDOW OR WONDOW BECOMING DETACHED FROM THE CHANNEL. *YC
866503A
SUBJECT REGARDING OBD II DIAGNOSTIC TROUBLE CODE (DTC) P1404 (REFLASH VCM). *YC
876525
COMMENTS OF AN EXTENDED ENGINE CRANKING TIME DURING A HOT RESTART IN HIGH AMBIENT TEMPERATURES OF 38 C (100 F). *YC
837110A
PARK/NEUTRAL POSITION SWITCH CONNECTOR CANNOT BE REMOVED. YD
876126
OIL WEEP OR LEAK AT GASKET BETWEEN UPPER AND LOWER INTAKE MANIFOLD. YD
866503
SOME VEHICLES MAY SET A FALSE OBD II WITH DIAGNOSTIC TROUBLE CODE P1404. *TT
98837110
TECHNICIANS MAY EXPERIENCE DIFFICULTY IN REMOVING THE CONNECTORS FROM THE PARK/NEUTRAL POSITION SWITCH, USUALLY WHEN TRYING TO REMOVE THE SWITCH DURING TRANSMISSION SERVICE. *YC
98876304
COMPLAINTS THAT THEIR VEHICLE IS DIFFICULT TO START OR WILL NOT START. *YC
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.