PIP5601C
Service Bulletin/Repair Instructions
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Vehicle report
2003 GMC SAVANA
Service bulletins
519 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
23-NA-001
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
PIP5358D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
03-06-01-023I
Service Bulletin/Repair Instructions
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP4723J
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
03-06-01-023H
Service Bulletin/Repair Instructions
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIT5099H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3271P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
General Communication
Service Campaign
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
24-NA-141
Service Bulletin/Repair Instructions
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
16-NA-383
Service Bulletin/Repair Instructions
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
09-00-89-008G
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
10-08-45-001H
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
22-NA-074
Service Bulletin/Repair Instructions
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
02-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
Service Bulletin/Repair Instructions
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
23-NA-219
Service Bulletin/Repair Instructions
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
17-NA-170
Service Bulletin/Repair Instructions
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
10-00-89-006J
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
23-NA-153
Service Bulletin/Repair Instructions
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
18-NA-073
Service Bulletin/Repair Instructions
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-144
Service Bulletin/Repair Instructions
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full Turns.
PIP5628G
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
03-06-01-023G
Service Bulletin/Repair Instructions
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP5358C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT3665M
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
19-NA-219
Service Bulletin/Repair Instructions
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
04-00-89-015Z
Service Bulletin/Repair Instructions
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
22-NA-009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
09-00-89-008F
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
Service Bulletin/Repair Instructions
This service bulletin provides information on Module Harvesting.
PIT3665L
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
10-00-89-006I
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
Service Bulletin/Repair Instructions
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
06-00-89-031H
Service Bulletin/Repair Instructions
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
22-NA-181
Service Bulletin/Repair Instructions
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
03-06-01-023F
Service Bulletin/Repair Instructions
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
20-NA-065
Service Bulletin/Repair Instructions
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5099F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
12-00-89-003B
Service Bulletin/Repair Instructions
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
03-06-01-023E
Service Bulletin/Repair Instructions
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
18-NA-102
Service Bulletin/Repair Instructions
This technical bulletin provides a procedure to repair a possible wiring harness repair if damaged by the parking brake, brake booster mount or brake pedal bolt.
04-06-04-051F
Service Bulletin/Repair Instructions
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
PIT3271M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP4723F
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
000090002L
Service Bulletin/Repair Instructions
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
PIT3099U
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
21NA124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
100089006H
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIT3271K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5628C
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3665J
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIC5453C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
030601023D
Service Bulletin/Repair Instructions
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP5628B
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
Service Bulletin/Repair Instructions
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
19NA219
Service Bulletin/Repair Instructions
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIT3099T
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100089009D
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
010842001M
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIT3271J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
100089006G
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
100089009C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
17NA073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIT3099S
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT3099R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
100845001G
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
PIT3665H
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT3665G
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIP5640
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5339A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
100845001F
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP3119P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP5540D
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010842001L
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
Service Bulletin/Repair Instructions
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
Service Bulletin/Repair Instructions
This Preliminary information communicates
PIP4138R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT5099D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5099C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5399A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
18NA102
Service Bulletin/Repair Instructions
This technical bulletin provides a procedure to repair a possible wiring harness repair if damaged by the parking bark, brake booster mount or brake pedal bolt.
PIP5226B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP4138Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT3271H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3665F
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIP5540A
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP3343F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP5540
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5353B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide
150089004B
Service Bulletin/Repair Instructions
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
PIP4723C
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-06-01-012G
Service Bulletin/Repair Instructions
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
15-08-44-001I
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
Service Bulletin/Repair Instructions
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
10-00-89-006F
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report.
PIT5389C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIT3665E
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
03-08-46-004S
Service Bulletin/Repair Instructions
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
07-08-49-020L
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP4138P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIC5492E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT3099N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
09-00-89-008C
Service Bulletin/Repair Instructions
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
07-08-49-020K
Service Bulletin/Repair Instructions
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC5491J
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
Service Bulletin/Repair Instructions
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
000601012F
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
15-08-44-001H
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVODES INFORMATION ON THE GM OF CANADA ONSTAR CELLULAR COMMUNICATION UPGRADE.
PIT-3665-D
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HYDRO-BOOST IS NOT SERVICEABLE AND WILL NEED TO BE REPLACED IF THE BRAKE PEDAL MOVES OR APPLIES ON ITS OWN AT A FULL TURN.
PIT-5485-B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC5088F
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC-4935-E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
Service Bulletin/Repair Instructions
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5484A
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIC5953A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5340A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT AFTER A TRANSMISSION OR TORQUE CONVERTER REPLACEMENT THE VEHICLE MAY HAVE A HARSH 1-2 UPSHIFT AND THE CHECK ENGINE LIGHT OR SERVICE ENGINE SOON INDICATOR IS ILLUMINATED. IF YOU HAVE DUPLICATED THE CUSTOMERS CONCERN AND FOUND DIAGNOSTIC TROUBLE CODE P0894 OR P1870 SET IN THE TRANSMISSION CONTROL MODULE PLEASE CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER.
02-08-42-001I
Service Bulletin/Repair Instructions
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
Service Bulletin/Repair Instructions
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
PIP5226A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
01-08-42-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
16-NA-025
Service Bulletin/Repair Instructions
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
Service Bulletin/Repair Instructions
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIC6140B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT5353A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5484
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT5486
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5016B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice.
PIT4943D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
06-00-89-031D
Service Bulletin/Repair Instructions
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
Service Bulletin/Repair Instructions
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIC6140A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIP5339
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
PIC5953B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIP3504D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a hard start when the engine is hot. If the fuel found in the vehicle has an American Petroleum Institute specific gravity reading of 39 - 44, and the fuel sample you used for comparison has an American Petroleum Institute specific gravity reading of 30 - 39, drain the fuel system and refill with a known good diesel fuel and retest.
PIP4404F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
PIT5464
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
09-09-40-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIC6107
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6101
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIT5384A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
02-07-30-052J
Service Bulletin/Repair Instructions
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
05-06-04-035E
Service Bulletin/Repair Instructions
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIP5016A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice.
02-08-42-001H
Service Bulletin/Repair Instructions
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
PIT5399
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5280
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have a buzz noise at idle after fuel pressure regulator replacement. Technician will need to gain access to the fuel pump. After gaining access to the fuel pump check the power and ground for voltage drop with the key in the off from the fuel pump to the battery post. Technician should also check the pin fit and terminal drag. Technician may replace the fuel pump connector with the updated part using the latest version service bulletin 04-06-04-088C. Technician should inspect voltage drop points at the UBEC, fuel pump relay, ground at the frame and the battery cable grounds. If excessive resistance is found at the crimps, replace the crimp n seal splice sleeves for the affected circuits. If the circuits do not have high resistance replace the regulator using part number 19236428.
05-08-46-006T
Service Bulletin/Repair Instructions
This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.
15-08-44-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PIT5264C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
10-08-45-001E
Service Bulletin/Repair Instructions
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
PI1396
Service Bulletin/Repair Instructions
This preliminary informational bulletin provides information to technicians that when replacing the passenger side airbag also install the I/P stow tray (trim piece).
PI1394
Service Bulletin/Repair Instructions
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
030848006J
Service Bulletin/Repair Instructions
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
Service Bulletin/Repair Instructions
This information provides the proper way to install the floor mats .
PIT5353
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5029F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
11-00-89-005H
Service Bulletin/Repair Instructions
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5264B
Service Bulletin/Repair Instructions
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
PIT5099A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
03-06-01-023B
Service Bulletin/Repair Instructions
This information bulletin explains how to measure for oil consumpsion and possible reasons for loss of oil.
PIP5232A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
Service Bulletin/Repair Instructions
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIC6036
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to use floor mats.
10-00-89-006E
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
PIT3099M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
Service Bulletin/Repair Instructions
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
05-02-32-008F
Service Bulletin/Repair Instructions
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers.
PIP5163A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
Service Bulletin/Repair Instructions
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
14-06-04-005
Service Bulletin/Repair Instructions
This information bulletin advises of a new tool used to aid in installing Duramax glow plugs.
UIB-117
Service Bulletin/Repair Instructions
GENERAL MOTORS: AN OPTIONAL ENGINE BLOCK HEATER PLUG IN FOR ONBOARD AC POWER AND WITH CONTINUOUS USAGE WILL RESULT IN SHORTING OF WIRES, OVER HEATING SYSTEM, ELECTRICAL FAILURE AND COMPARTMENT ENGINE FIRES. MODEL 2003-15 EXPRESS CUT AWAY VANS, SILVERADO CHASSIS CAB, SAVANA CUT AWAY VANS, SIERRA CHASSIS CAB. *PE
10-00-89-006D
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
140604005
Service Bulletin/Repair Instructions
Duramax® Diesel Glow Plugs Difficult to Install Due to Carbon Buildup - New Glow Plug Bore Reamer Available
Recalls
Service Bulletin/Repair Instructions
Vehicle Recalls
PIC5088E
Service Bulletin/Repair Instructions
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
05-08-46-006S
Service Bulletin/Repair Instructions
This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.
13-00-89-004I
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
05-06-04-035D
Service Bulletin/Repair Instructions
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
Service Bulletin/Repair Instructions
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
PIT3099L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
13-00-89-004H
Service Bulletin/Repair Instructions
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
PIP3343E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP3343D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
13-00-89-004G
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5264
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIT4864F
Service Bulletin/Repair Instructions
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
13-00-89-004F
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT4943C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
99-08-51-007F
Service Bulletin/Repair Instructions
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5169
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
PI0281D
Service Bulletin/Repair Instructions
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
Service Bulletin/Repair Instructions
This informational bulletin provides directions on submitting different PIRs
13-00-89-004E
Service Bulletin/Repair Instructions
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
05-00-89-072C
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
13-00-89-004D
Service Bulletin/Repair Instructions
This informational bulletin provides an update for 13-00-89-004C to include updated information.
04-06-04-047L
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
10-08-110-001A
Service Bulletin/Repair Instructions
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
PIP5163
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT3099K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130089009
Service Bulletin/Repair Instructions
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIC5904
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
00-03-10-003R
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
PIP4138N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
10-00-89-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
09-08-64-030A
Service Bulletin/Repair Instructions
This technical bulletin provides a revision for 09-08-64-030 to update the Parts and Warranty Information.
07-08-49-020H
Service Bulletin/Repair Instructions
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
PI-0011A
Service Bulletin/Repair Instructions
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
02-07-30-052I
Service Bulletin/Repair Instructions
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
08-06-01-006D
Service Bulletin/Repair Instructions
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
02-08-98-002D
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
09-00-89-008A
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
05-08-48-001C
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
13-00-89-004B
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PIT4720C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
05-02-32-008E
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 05-02-32-008D to add 2013 Model Year vehicles.
13-00-89-005
Service Bulletin/Repair Instructions
This technical bulletin provides Warranty Administration - New Labor Codes information.
13-00-89-004A
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.
99-04-20-002H
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
13-00-89-004
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
11-00-89-005D
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
10-00-89-017Z
Service Bulletin/Repair Instructions
This informational bulletin provides information on fix it right for first time issues.
00-03-10-002G
Service Bulletin/Repair Instructions
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
PIP3140E
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
08-08-51-002A
Service Bulletin/Repair Instructions
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
PIP4138M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP4138L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
11-00-89-005C
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIP3259J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have a planetary gear whine noise in first and second gear. Technician should compare the noise to a like vehicle. Technician will need to check the build date of the transmission, if it was built after 09/01/2003 and it is determined that a vehicle has an abnormal amount of noise, perform the rear unit end play check. Technician will replace the output planetary gear set if end play is out of specification. The transmission assembly will need to be replaced if the end play is with in specification.
PIC3718E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PIT3271F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
10-00-89-017X
Service Bulletin/Repair Instructions
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
G-12167
Service Bulletin/Repair Instructions
12167 - SPECIAL COVERAGE. WATER AND ROAD CONTAMINATES MAY BECOME TRAPPED IN THE PROTECTIVE CONDUIT THAT COVERS THE FUEL FILLER PIPE AND MAY CAUSE THE PIPE TO CORRODE. IF THE CORROSION CREATES A PERFORATION IN THE PIPE, THE PRESENCE OF FUEL ODOR MAY BE OBSERVED AND, ON SOME VEHICLES, A CHECK ENGINE LIGHT MAY ILLUMINATE. AS THE SIZE OF A FILLER PIPE PERFORATION INCREASES, FUEL MAY LEAK ONTO THE GROUND WHILE REFUELING THE VEHICLE. IF THE CONDITION OCCURS WITHIN THE TERMS OF THE SPECIAL COVERAGE, DEALERS ARE TO INSTALL A NEW FUEL FILLER PIPE.
SB-12167-A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
12167
Service Bulletin/Repair Instructions
Special Coverage Adjustment - Fuel Filler Pipe Corrosion
SB-12167
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-08-46-004A
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
080846004A
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
08-08-44-015C
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
00-00-89-027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
000089027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
12-03-10-002
Service Bulletin/Repair Instructions
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
06-00-89-026J
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
PIT5178
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that some vehicles may have an Antilock Braking System/ Traction Control System Malfunction Indicator Lamp are on or other various electrical issues. Technician should inspect the braided ground strap from the engine to the frame.
10-00-89-010B
Service Bulletin/Repair Instructions
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
100089010B
Service Bulletin/Repair Instructions
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
12-00-89-002A
Service Bulletin/Repair Instructions
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
010089010J
Service Bulletin/Repair Instructions
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
10-00-89-017W
Service Bulletin/Repair Instructions
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
100089017W
Service Bulletin/Repair Instructions
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
PIT4907A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT3665C
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIC4935D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIP5072
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
PIT3099J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
11-00-89-005B
Service Bulletin/Repair Instructions
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
10-00-89-017V
Service Bulletin/Repair Instructions
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PIC5588A
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
SB-11359
Service Bulletin/Repair Instructions
GM: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT- FUEL FILLER NECK CORROSION. WATER AND ROAD CONTAMINATES MAY BECOME TRAPPED IN THE PROTECTIVE CONDUIT THAT COVERS THE FUEL FILLER PIPE AND MAY CAUSE THE PIPE TO CORRODE. THE PRESENCE OF FUEL ODOR MAY BE OBSERVED AND, ON SOME VEHICLES, A CHECK ENGINE LIGHT MAY ILLUMINATE. *JS
PIT-3749D
Service Bulletin/Repair Instructions
GM: ON SOME TRUCK MODELS THERE IS SOME FRAME CORROSION. *RM UPDATED ON 5/2/2012. *KB
09-09-40-001A
Service Bulletin/Repair Instructions
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
SB-10-08-50-003B
Service Bulletin/Repair Instructions
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
PIP-4492P
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE
030232003
Service Bulletin/Repair Instructions
STEERING NOISE WHEN TURNING LEFT. *TT UPDATED 3/4/11. *PE UPDATED ON 6/30/2011. *KB
10-00-89-017C
Service Bulletin/Repair Instructions
GM: INFORMATION ON FIXING MULTIPLE SITUATIONS RIGHT THE FIRST TIME. *RM
PIP-4138K
Service Bulletin/Repair Instructions
GM: THE SERVICE ENGINE SOON LIGHT IS ON, THERE IS ALSO A MISFIRE OR ENGINE NOISE. THERE ARE MULTIPLE POSSIBLE CAUSES. *RM
SB-10-02-33-001
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. TECHNICIANS HAVE BEEN REPLACING ENTIRE STEERING GEARS DUE TO NOT BEING ABLE TO SERVICE JUST LEAKING PITMAN SHAFT SEAL. *PE UPDATED 5/9/11. *PE
030525007
Service Bulletin/Repair Instructions
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS (CLEAN WHEEL SPEED SENSOR MOUNTING SURFACE). *TT UPDATED 10/23/09. *PE
08089-B
Service Bulletin/Repair Instructions
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
08-089
Service Bulletin/Repair Instructions
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
08-07-30-015
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION ON MN8, MT1 SES/MIL ILLUMINATED, DTC P0757, HARSH SHIFT, DELAYED 2-3 SHIFT, 2-3 SHIFT FLARE, NO THIRD GEAR, SLIPS IN THIRD GEAR OR REVERSE. *PE
PIP3343
Service Bulletin/Repair Instructions
POSSIBLE ENGINE OIL LEAK DUE TO PCV FREEZE-UP, EQUIPPED WITH THE 4.8, 5.3, 6.0, AND 6.2 V-8 ENGINES. *NJ
PIP4054A
Service Bulletin/Repair Instructions
EATON LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS, EQUIPPED WITH A LOCKING REAR DIFFERENTIAL RPO G80. *NJ UPDATED 7/17/2008. *PE
4070
Service Bulletin/Repair Instructions
TRANSFER CASE FRONT INPUT SHAFT SEAL IS POPPED OUT. EQUIPPED WITH (AWD). *NJ
07095
Service Bulletin/Repair Instructions
ENGINE COMPARTMENT FUSE BLOCK COVER ON SOME 2003-2007 CHEVROLET EXPRESS AND GMC SAVANA VEHICLES MAY BREAK WHEN THE COVER IS REMOVED, ALLOWING WATER AND ROAD CONTAMINATES TO ENTER THE FUSE BLOCK. *NJ
030309002
Service Bulletin/Repair Instructions
REAR LEAF SPRING SLAP OR CLUNK NOISE (REPLACE SPRING INSERTS) *TT UPDATED 10/18/07. *NJ
050308019
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION FOR NOISE IN STEERING AND INSPECTION OF IDLER ARM BRACKET. *KB UPDATED ON 09/19/07. *NJ
070864010
Service Bulletin/Repair Instructions
VARIOUS REAR SLIDING DOOR CONDITIONS. *KB
07103
Service Bulletin/Repair Instructions
STEERING IDLER ARM ATTACHING BRACKET FRACTURE. *KB
030604030
Service Bulletin/Repair Instructions
MULTIPLE DRIVEABILITY SYMPTOMS OF LONG OR HARD STARTS, CHUGGLE, ROUGH IDLE AND LIGHT OR INTERMITTENT MISFIRE DUE TO CLOGGED FUEL INJECTORS. *TT
030864031
Service Bulletin/Repair Instructions
MIRROR SHAKES OR VIBRATION WHILE DRIVING. *TT
3238
Service Bulletin/Repair Instructions
PRNDL LIGHT UP WITH KEY OUT OF IGNITION AND DOOR OPEN. *EH
060522006
Service Bulletin/Repair Instructions
HYDRO-BOOST UNIT/POWER BRAKE BOOSTER APPEARS TO BE LEAKING. *KB
060864032
Service Bulletin/Repair Instructions
SIDE CARGO DOOR IS HARD TO OPEN. INSTALL NEW HINGE PINS. *KB
050604077
Service Bulletin/Repair Instructions
LACK OF POWER LU3 ENGINE) AT HIGH AMBIENT TEMPERATURES ONLY (IF NECESSARY, REPROGRAM PCM WITH NEW SERVICE CALIBRATION).*AK
010730038B
Service Bulletin/Repair Instructions
THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
050846006A
Service Bulletin/Repair Instructions
INFORMATION ON UPGRADING CERTAIN ONSTAR GENERATION 5 ANALOG/DIGITAL-READY SYSTEMS TO ONSTAR GENERATION 6 DUAL-MODE (ANALOG/DIGITAL). *TT
020730024A
Service Bulletin/Repair Instructions
DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
050601014
Service Bulletin/Repair Instructions
OIL LEAK UNDER EXTREME COLD TEMPERATURES (-34 DEGREES C) (-30 DEGREES F) OR COLDER). *TT
03102005
Service Bulletin/Repair Instructions
STEERING GEAR WHISTLE NOISE ON TURNS. *EH
020307002
Service Bulletin/Repair Instructions
REVISED FRONT CASTER AND CAMBER ADJUSTMENT PROCEDURE. ORIGINAL NOT YET RECEIVED. *TT
050604021
Service Bulletin/Repair Instructions
REVISED INSPECTION/MAINTENANCE (I/M) EVAPORATIVE EMISSION (EVAP) SYSTEM SET PROCEDURE. *TT
030604041
Service Bulletin/Repair Instructions
POOR ENGINE PERFORMANCE - MISFIRE, ROUGH IDLE, SERVICE ENGINE SOON/CHECK ENGINE LIGHT ILLUMINATED, DIAGNOSTIC TROUBLE CODE (DTC) P0300 SET. *TT
050525002
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION ON ANTILOCK BRAKE SYSTEM (ABS) DIAGNOSTIC TROUBLE CODE(S) (DTC) C0035, C0040, C0050, C0055 AND/OR P0609. *TT
020526001B
Service Bulletin/Repair Instructions
REAR PARKING BRAKE SHOE RETAINING SPRING CLIP SERVICE KIT FOR DRUM-IN-HAT (DIH) EQUIPPED VEHICLES. *TT UPDATE. *TT
040846004
Service Bulletin/Repair Instructions
ONSTAR SYSTEM INOPERATIVE ONSTAR SYSTEM STATUS LIGHT IS RED RADIO LOCKED IN PHONE MODE OR DTC B1000. *EH
030235006
Service Bulletin/Repair Instructions
REVISED STEERING WHEEL REPLACEMENT PROCEDURE. *TT
020846010E
Service Bulletin/Repair Instructions
PROGRAMMING ONSTAR MODULE FOR CANADIAN FRENCH VOICE RECOGNITION. *TT UPDATE. *TT UPDATED *EH
030138019
Service Bulletin/Repair Instructions
UNDERHOOD AIR CONDITIONER RATTLE NOISE HEARD ON ACCELERATION OR A SUDDEN LOSS OF AIR CONDITIONER SYSTEM PERFORMANCE. *TT THIS BULLETIN REPLACES 03-01-38-019 DATED 11-01-2003. TO INCLUDE VARIOUS MODLES INCLUDING 2002-2004 COMMERCIAL UPFITTER CHASSIS VEHICLES. *TT
040604057
Service Bulletin/Repair Instructions
START/STALL OR POOR DRIVEABILITY AFTER RESTART, LOSS OF GASOLINE OR CNG HOURS/MILES DATA WITH BI-FUEL VEHICLE. *TT
040849021
Service Bulletin/Repair Instructions
VEHICLES ORDERED WITHOUT ASHTRAY SMOKERS PACKAGE ASHTRAY AVAILABLE THROUGH SPO. *EH
040604049
Service Bulletin/Repair Instructions
FALSE START WITH MALFUNCTION INDICATOR LAMP LIGHT ON, P0191. *TT
040604050
Service Bulletin/Repair Instructions
CNG FUEL LEVEL READS HIGHER THAN ACTUAL, INACCURATE FUEL LEVEL READING, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED. *TT
07012004
Service Bulletin/Repair Instructions
OIL LIFE SYSTEM RESET PROCEDURES-TRUCKS. BUICK TERAZZA 2005, GMC SIERRA DENALI 2002-2003, GMC B7 CHASSIS MEDIUM DUTY 2003-2005 AND GMC 560 C-SERIES 2003-2005 *SC
030310002
Service Bulletin/Repair Instructions
USE OF CORRECT INSTALLATION PROCEDURE FOR LOOSE HUBCAP ASSEMBLY. THIS SERVICE BULLETIN REPLACES 030310002. *EH
040843004
Service Bulletin/Repair Instructions
WINDSHIELD WIPERS WON'T SHUT OFF. *EH
04152004
Service Bulletin/Repair Instructions
GM IS ANNOUNCING A PRODUCT EMISSION RECALL, NUMBER 04016. VEHICLES COULD HAVE THE .02 ENGINE OFF NATURAL VACUUM, EONV, EVAPORATIVE EMISSION SYSTEM LEAK DETECTION DIAGNOSTIC DISABLED BY THE POWERTRAIN CONTROL MODULE THAT INCORRECTLY REFERENCES A FULL OR EMPTY FUEL TANK. POWERTRAIN CONTROL MODULE IS TO BE REPROGRAMMED. GM VOICEMAIL EXPRESS. *TT
04016
Service Bulletin/Repair Instructions
EVAPORATIVE EMISSION SYSTEM DIAGNOSTIC DISABLED BY INCORRECT FUEL LEVEL REFERENCE. RECALL BULLETIN. *TT
040604028
Service Bulletin/Repair Instructions
VARIOUS DRIVEABILITY CONCERNS CHECK ENGINE LIGHT ON DIAGNOSTIC TROUBLE CODE SET. *EH
040845004
Service Bulletin/Repair Instructions
VARIOUS ELECTRICAL CONCERNS AIR BAG LIGHT ON ANTILOCK BRAKE LIGHT ON SECURITY LIGHT ON CHECK ENGINE LIGHT ON DTCS SET GAUGES INOPERATIVE. *EH
030604033
Service Bulletin/Repair Instructions
REVISED DIAGNOSTIC TROUBLE CODE P0336. *TT UPDATE. TO INCLUDE 2004 ISUZU NQR COMMERCIAL MODELS. *TT
040495001
Service Bulletin/Repair Instructions
REVISED WHEEL DRIVE SHAFT NUT TORQUE SPECIFICATION. *TT
040604009
Service Bulletin/Repair Instructions
REDUCED POWER, INTERMITTENT HESITATION, STALL IN HIGH ALTITUDE/HIGH AMBIENT TEMPERATURES. *TT
030849012
Service Bulletin/Repair Instructions
CHANGE ENGINE OIL LIGHT ON. *TT UPDATE. *TT
040603001
Service Bulletin/Repair Instructions
INCORRECT AMP CODE GENERATOR. *EH
040603002
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION FOR INTERMITTENT VEHICLE NO CRANK DEAD BATTERY. *EH
00428E
Service Bulletin/Repair Instructions
HIGHER THAN EXPECTED OIL CONSUMPTION EVEN AFTER THE INTAKE BOLTS WERE REPLACED PER 02-06-01-035. *TT
00559C
Service Bulletin/Repair Instructions
4L80E, 4L85E AUTOMATIC TRANSMISSION DIAGNOSTIC TROUBLE CODE (DTC) P0706 AND VEHICLE MAY NOT START. *TT
00632
Service Bulletin/Repair Instructions
4.3L L35 ENGINE-DIAGNOSTIC TROUBLE CODE P0300 BUT NO MISFIRE CAN FELT. *MJ
00700A
Service Bulletin/Repair Instructions
4.3L L35 ENGINE WIDE OPEN THROTTLE DIAGNOSTIC TROUBLE CODE (DTC) P0335, P0336, P0339. *TT *MJ
00702
Service Bulletin/Repair Instructions
SLIP CONDITION IN 2ND, 3RD OR 4TH DAMAGED 2-4 BAND 3-4 CLUTCH ON THE 4L60E/4L65E AUTOMATIC TRANSMISSION. *TT *MJ
00823A
Service Bulletin/Repair Instructions
POWER STEERING FLUID LEAKING AT HYDRAULIC BRAKE BOOSTER. *TT
00969A
Service Bulletin/Repair Instructions
ENGINE WHISTLE NOISE. *TT
010605003
Service Bulletin/Repair Instructions
VIBRATION OR RATTLE-TYPE NOISE COMING FROM THE EXHAUST SYSTEM AT IDLE WITH ENGINE RPMS BETWEEN 613 AND 712. *TT THIS BULLETIN REPLACED 01-06-05-003 DATED 07/01/2001. *TT
01086B
Service Bulletin/Repair Instructions
DEALERS MAY COMMENT THAT THE ODOMETER HAS RESET TO 0 AFTER THE BATTERY HAS BEEN DISCONNECTED. *TT
01119A
Service Bulletin/Repair Instructions
ROLL-OUT FOR THE GEN III SMALL BLOCK ENGINES WITH IRIDIUM SPARK PLUGS. ALSO INCLUDES 2003/2004 M/L VANS. *TT
01222A
Service Bulletin/Repair Instructions
REPEAT REAR AXLE HUB SEAL LEAK. *TT
01225
Service Bulletin/Repair Instructions
ENGINE COOLANT LEAK AT INTAKE GASKET. * MJ
01322A
Service Bulletin/Repair Instructions
ELECTRONIC BRAKE CONTROL MODULE PART RESTRICTION. SERVICE VME. *TT *MJ
01340B
Service Bulletin/Repair Instructions
SEIZED 2-PIECE PROPELLER SHAFT WITH THE CENTER SUPPORT BEARING PULLED OUT OF THE RUBBER. SIT BULLETIN 1400140. *TT
01353
Service Bulletin/Repair Instructions
ENGINE MISFIRE DUE TO INJECTOR FRETTING CORROSION. *TT
01483
Service Bulletin/Repair Instructions
VEHICLE HAS NO PCM (POWER TRAIN CONTROL MODULE) COMMUNICATION WITH TECH 2. SIT BULLETIN 1400427. *TT
01485
Service Bulletin/Repair Instructions
TIMING CHAIN TENSIONER BREAKPOINTS FOR SERVICE KIT OR PRODUCTION FIX. RATTLE-TYPE NOISE COMING FROM THE ENGINE AT APPROXIMATELY 1800 TO 2200 RPMS. 4.3L LU3 L35 ENGINE. *TT
01485A
Service Bulletin/Repair Instructions
TIMING CHAIN TENSIONER BREAKPOINTS FOR SERVICE KIT OR PRODUCTION FIX FOR VEHICLE EXHIBITING RATTLE-TYPE NOISE COMING FROM THE ENGINE AT APPROXIMATELY 1800 TO 2200 RPMS. SIT BULLETIN 1408407. *TT
01485B
Service Bulletin/Repair Instructions
TIMING CHAIN TENSIONER BREAKPOINTS FOR SERVICE KIT OR PRODUCTION FIX. RATTLE-TYPE NOISE COMING FROM THE ENGINE AT APPROXIMATELY 1800 TO 2200 RPMS. 4.3L LU3 L35 ENGINE. *TT
01599
Service Bulletin/Repair Instructions
4L60E, 4L65E FORWARD AND LOW REVERSE WAVED STEEL CLUTCH PLATE APPEARANCE CHANGE. *TT
01626
Service Bulletin/Repair Instructions
4L60E AND 4L80E AUTOMATIC TRANSMISSION FLUID LEVEL INDICATOR (DIPSTICK) WILL NOT STAY SEATED. *MR
01700
Service Bulletin/Repair Instructions
STAMPING ERROR ON GENERATOR ASSEMBLY. SIT BULLETIN 1452615. *TT
01863
Service Bulletin/Repair Instructions
LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE MANEUVERS. *MR
01864
Service Bulletin/Repair Instructions
RADIO CD SKIPS/EJECTS OR CLOCK RESETS TO 12:00. *MR *TT
01897
Service Bulletin/Repair Instructions
LACK OF STEERING ASSIST OR SHUDDER DURING PARKING LOT TYPE MANEUVERS. *MR
01919
Service Bulletin/Repair Instructions
REPLACEMENT RADIO READS CAL ERROR, HAS NO AUDIO OR WILL NOT PROGRAM. *TT
01919A
Service Bulletin/Repair Instructions
REPLACEMENT RADIO READS CAL ERROR, HAS NO AUDIO OR WILL NOT PROGRAM. *TT
01950
Service Bulletin/Repair Instructions
ABS TELLTALE ILLUMINATED, DIAGNOSTIC TROUBLE CODE C0550 STORED IN HISTORY.*MR
02053
Service Bulletin/Repair Instructions
INFORMATION ON RESURFACING THE PARK BRAKE PORTION OF THE REAR BRAKE ROTOR. *TT
02085
Service Bulletin/Repair Instructions
SIR/AIR BAG LIGHT ON DIAGNOSTIC TROUBLE CODE (DTC) B0058, B0059, B0065 AND/OR B0066 AFTER SDM REPLACEMENT. *TT
02086
Service Bulletin/Repair Instructions
4L60E, 4L65E INTERMITTENT NEUTRAL FROM A STOP OR STEADY SPEED. *TT
3000A
Service Bulletin/Repair Instructions
REAR AXLE LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS. *MJ
3015
Service Bulletin/Repair Instructions
6.0L LQ4 VIN U ENGINE RESTRICTION. *TT
3018
Service Bulletin/Repair Instructions
ENGINE CYLINDER HEAD CUP PLUG COOLANT LEAK. *MJ
3024
Service Bulletin/Repair Instructions
GEN III ENGINE COATED PISTON INFORMATION. *TC
3038
Service Bulletin/Repair Instructions
ENGINE TICK, RATTLE OR KNOCK NOISE AFTER CYLINDER HEAD GASKET REPLACEMENT ON THE 6.0L ENGINE. *TT
3048
Service Bulletin/Repair Instructions
TIMING CHAIN TENSIONER BREAKPOINTS FOR SERVICE KIT OR PRODUCTION KIT. SUPPLEMENT TO 03-06-01-024B. *TT
3050A
Service Bulletin/Repair Instructions
02-05 ONSTAR EQUIPPED VEHICLES EMITTING BEEPING NOISE BEFORE CONNECTING TO ONSTAR. *TT
3051
Service Bulletin/Repair Instructions
CRUISE CONTROL AND/OR THE POWER TAKE OFF UNIT (PTO) MAY BE INOPERATIVE. *TT
3055
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT WITH A P0300 MISFIRE DUE TO MISFIRES MAINLY ON CYLINDER 7. *TT
3058
Service Bulletin/Repair Instructions
GOODWRENCH ENGINE AND REPLACEMENT CRANKSHAFT INFORMATION. *TT
3096
Service Bulletin/Repair Instructions
INTERMITTENT AIR BAG TELLTALE SETS A FALSE DIAGNOSTIC TROUBLE CODE OF B0083 AND OR B0084. *SC
3097
Service Bulletin/Repair Instructions
OIL PAN OR OIL COOLER LINE LEAK. *SC
01086A
Service Bulletin/Repair Instructions
DEALERS MAY COMMENT THAT THE ODOMETER HAS RESET TO 0 AFTER THE BATTERY HAS BEEN DISCONNECTED. *TT
01275C
Service Bulletin/Repair Instructions
SOME OWNERS OF 03 G-VANS OR 04 C/K TRUCKS DRIVING AT HIGH ALTITUDE WITH WARM AMBIENT TEMPERATURES MAY COMPLAIN OF A STALL AND OR LACK OF POWER OR RUNNING ROUGH CONDITION UNTIL THE VEHICLE COOLS DOWN. *TT
01325
Service Bulletin/Repair Instructions
STEERING SQUAWK NOISE ON LEFT HAND TURNS. *TT
01340
Service Bulletin/Repair Instructions
SEIZED 2 - PIECE PROP AND CENTER SUPPORT BEARING PULLED OUT. *TT
01368A
Service Bulletin/Repair Instructions
COOLANT LOSS (INTO THE CRANKCASE). *TT
030730056
Service Bulletin/Repair Instructions
4L60-E AUTOMATIC TRANSMISSION OIL PUMP FIRST AND SECOND DESIGN IDENTIFICATION. *TT
030858006
Service Bulletin/Repair Instructions
NOISE FROM TOP OF WINDSHIELD OR THE MOLDING IS LOOSE. *TT
030603001A
Service Bulletin/Repair Instructions
STARTER CRANKS AFTER KEY IS RELEASED (NORMAL CONDITION). *TT
030138016
Service Bulletin/Repair Instructions
POOR AIR CONDITIONING (A/C) PERFORMANCE - A/C WILL NOT BLOW COLD ENOUGH. *TT
081103
Service Bulletin/Repair Instructions
THIS VME STATES THAT GM HAS DECIDED THAT CERTAIN VEHICLES DO NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD 225 IN BOTH US AND CANADA BECAUSE THE OWNERS MANUAL DOES NOT INCLUDE THE LOCATION SYMBOLS FOR THE LOWER UNIVERSAL ANCHORAGE SYSTEM AND EXPLANATION OF THE MEANING OF THE SYMBOLS. RECALL 03039 FOR CHILD SEAT ANCHORAGE SYSTEM. *TT
010730002C
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) IS ON; THE TRANSMISSION IS STUCK IN THIRD GEAR; AND / OR THE INSTRUMENT CLUSTER IS INOPERATIVE. *TT
030601023
Service Bulletin/Repair Instructions
HIGHER THAN EXPECTED OIL CONSUMPTION <8500 GVW. VARIOUS MODELS INCLUDING 2003-2004 CHEVROLET KODIAK (C4500-C5500 SERIES MODELS)AND GMC TOPKICK (C4500-C5500 SERIES MODELS). *TT
030601024
Service Bulletin/Repair Instructions
RATTLE NOISE IN ENGINE. *TT
030858004
Service Bulletin/Repair Instructions
WHISTLE/WIND NOISE AROUND RIGHT CORNER AREA OF DASH. *TT
030940005
Service Bulletin/Repair Instructions
NEW FRONT SEAT BELT DESIGN. *TT
061603
Service Bulletin/Repair Instructions
GM WILL BE ANNOUNCING A SAFETY RECALL REGARDING UNSEALED REAR LICENSE PLATE LAMP SOCKETS THAT MAY CORRODE DUE TO WATER AND CONTAMINATES ENTERING THE REAR LICENSE PLATE LAMP ASSEMBLY. *TT
010846002C
Service Bulletin/Repair Instructions
PROGRAMMING OF REPLACEMENT ONSTAR VEHICLE COMMUNICATION AND INTERFACE MODULES (VCIM). *TT
030138008
Service Bulletin/Repair Instructions
REVISED DEFROSTER ACTUATOR REPLACEMENT PROCEDURE. *TT
052703
Service Bulletin/Repair Instructions
DURING A VEHICLE CRASH OF SUFFICIENT SEVERITY TO DEPLOY THE SAFETY BELT RETENTIONER, THE FRONT SAFETY BELT BUCKLES IN SOME VEHICLES MAY NOT RELEASE AFTER THE VEHICLE CRASH OR ALTERNATELY MAY EJECT THE FRONT SAFETY BELT LATCHES DURING THE VEHICLE CRASH RESULTING IN INCREASED RISK OF PERSONAL INJURY. NEW PRODUCT FIELD ACTION NUMBER 03007, FRONT SAFETY BELT BUCKLES. *TT
020844020B
Service Bulletin/Repair Instructions
NO AUDIO OUT OF SPEAKERS AT TIMES. *TT
020844020A
Service Bulletin/Repair Instructions
NO AUDIO OUT OF SPEAKERS AT TIMES. *TT
010903
Service Bulletin/Repair Instructions
FUEL FILL DIFFICULTIES, PREMATURE SHUTOFF OF THE FUEL FILL NOZZLE. GM VOICEMAIL EXPRESS. *TT
01432
Service Bulletin/Repair Instructions
AUTOMATIC TRANSMISSION POOR ACCELERATION, PERFORMANCE. *TT
030525001
Service Bulletin/Repair Instructions
THUMPING NOISE / FEEL IN BRAKE PEDAL. 1500/2500 SERIES HEAVY DUTY CARGO VANS. *TT
02059
Service Bulletin/Repair Instructions
WRONG SPARK PLUGS. *TT
02063
Service Bulletin/Repair Instructions
GENERAL MOTORS HAS DECIDED THAT A DEFECT THAT RELATES TO MOTOR VEHICLE SAFETY EXISTS IN CERTAIN VEHICLES WITH AN 8500 OR GREATER GVW RATING. ON SOME OF THESE VEHICLES THE NUT ATTACHING THE PITMAN ARM TO THE STEERING LINKAGE MAY NOT BE TORQUED TO SPECIFICATION, WHICH COULD LEAD TO A POSSIBLE SEPARATION WHICH COULD RESULT IN A LOSS OF VEHICLE CONTROL AND A CRASH COULD OCCUR WITHOUT PRIOR WARNING. *TT *JB
120402
Service Bulletin/Repair Instructions
STOP DELIVERY OF ALL 2003 MODEL YEAR CHEVROLET EXPRESS AND GMC SAVANA VANS BUILT BETWEEN OCTOBER 14, 2002 AND OCTOBER 25, 2002. *TT *JB
020417003
Service Bulletin/Repair Instructions
BOOM NOISE OR VIBRATION. 1500/2500 SERIES AWD VANS. *TT
020604059
Service Bulletin/Repair Instructions
ENGINE RUNS ROUGH, SERVICE ENGINE SOON LIGHT ON, DIAGNOSTIC TROUBLE CODES P0300 OR P0335 SET. *TT
02058
Service Bulletin/Repair Instructions
TIE ROD END NUT UNDER-TORQUED. *TT
11212002
Service Bulletin/Repair Instructions
RIGHT HAND TIE ROD END MAY NOT BE TORQUED TO SPECIFICATION. *EH
020604055
Service Bulletin/Repair Instructions
VEHICLE IS DIFFICULT TO FILL WITH FUEL. *TT
10162002
Service Bulletin/Repair Instructions
NOISE IN THE BRAKE PEDAL AFTER THE VEHICLE COMES TO A COMPLETE STOP MOST LIKELY OCCUR AFTER A HARD NON ABS STOP ON DRY PAVEMENT. *TT
10152002
Service Bulletin/Repair Instructions
FUEL FILL DIFFICULTIES, PREMATURE SHUTOFF OF THE FUEL NOZZLE. *TT
10082002
Service Bulletin/Repair Instructions
THIS MESSAGE IS TO PROVIDE DEALERS WITH AN AWARENESS OF TWO NEW COMMANDS AVAILABLE VIA VOICE RECOGNITION IN THE ONSTAR GENERATION FIVE EQUIPPED VEHICLES. THE TWO COMMANDS ARE ONSTAR AND EMERGENCY. *TT
990730016A
Service Bulletin/Repair Instructions
DIAGNOSTIC INFORMATION FOR INTERMITTENT TRANSMISSION DOWNSHIFT, SLIP, BUSY/CYCLING TCC OR NOISY COOLING FAN. *TT
020602008
Service Bulletin/Repair Instructions
NEW ENGINE COOLANT FILL PROCEDURE. *TT
020525005
Service Bulletin/Repair Instructions
SUBJECT REGARDING DIAGNOSTIC TROUBLE CODE C0201 SET AND STORED IN HISTORY. *TT
00773
Service Bulletin/Repair Instructions
4L60E, 4L65E REPLACEMENT VALVE BODY GASKETS DOES NOT SEEM TO FIT. *TT
01342
Service Bulletin/Repair Instructions
4.3L LU3 ENGINE HOT SOAK HESITATION LOW POWER. *TT
3001
Service Bulletin/Repair Instructions
THE SERVICE INFORMATION AND OWNERS MANUAL DO NOT SHOW A SERVICE INTERVAL FOR THE 8.6, 9.5, 9.75, 10.5, AND 11.5 INCH REAR AXLES WITH OR WITHOUT G80 (LOCKING DIFFERENTIAL). *TT 2006 ALL GENERAL MOTORS LIGHT DUTY TRUCKS, VANS AND UTILITIES. *TT
3002
Service Bulletin/Repair Instructions
4L60E/4L65E INTERMITTENT NEUTRAL CONDITION WHILE ACCELERATING FROM A STOP OR WHILE DRIVING. *TT 1999-2006 GM CARS, LIGHT DUTY TRUCKS AND UTILITIES. *TT
3044
Service Bulletin/Repair Instructions
GENERATION 5 ONSTAR STEERING WHEEL CONTROL FUNCTION. *TT
3048A
Service Bulletin/Repair Instructions
SUPPLEMENT TO 03-06-01-024B 4.3L LU3 L35 TIMING CHAIN TENSIONER. RATTLE-TYPE NOISE COMING FROM THE ENGINE AT APPROXIMATELY 1800 TO 2200 RPMS. *TT
3056
Service Bulletin/Repair Instructions
CHECK ENGINE LIGHT WITH A P0300 DUE TO 2-4 CYLINDERS MISFIRING ON THE SAME BANK OF THE ENGINE. *TT
3089
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT
3136
Service Bulletin/Repair Instructions
SLIP CONDITION IN 2ND, 3RD, OR 4TH. DAMAGED 2-4 OR 3-4 CLUTCH. *KB UPDATED 10/31/07. *NJ
3232
Service Bulletin/Repair Instructions
1999 - 2005 GEN II COLD ENGINE MISFIRE AT IDLE WITH POSSIBLE P0171 AND/OR P0174. *TT
3259C
Service Bulletin/Repair Instructions
4L80E, 4L85E WHINE NOISE IN FIRST AND SECOND GEAR. *TT
3276
Service Bulletin/Repair Instructions
4L80E OUTPUT CARRIER THRUST WASHER CHANGES. *TT
3320
Service Bulletin/Repair Instructions
CLUNK POP NOISE IN THE FRONT SUSPENSION OVER BUMPS. *TT
3340
Service Bulletin/Repair Instructions
INSTRUMENT PANEL CLUSTER WILL NOT ILLUMINATE IN DRL MODE. *TT
3364
Service Bulletin/Repair Instructions
REAR AXLE RETAINER BUTTON BREAKAGE. *EH
3375
Service Bulletin/Repair Instructions
COOLANT LEAK FROM THE LOWER RADIATOR HOSE. *TT
3427
Service Bulletin/Repair Instructions
ADDITIONAL DIAGNOSTIC INFORMATION DTC P0757. *TT
3487
Service Bulletin/Repair Instructions
THE SLIDING DOOR IS HARD TO OPEN OR WILL NOT OPEN. *TT
3491
Service Bulletin/Repair Instructions
ANTI-LOCK BRAKING SYSTEM (ABS) TELLTALE ILLUMINATED WITH DIAGNOSTIC TROUBLE CODE C0550. *TT
3499
Service Bulletin/Repair Instructions
STEERING IDLER ARM INSPECTION PROCEDURE. *TT
3514
Service Bulletin/Repair Instructions
HARNESS LOCATION FOR TRAILER BRAKE INSTALLATION RPO Z82 AND/OR UY7. *TT
3521
Service Bulletin/Repair Instructions
ANTI-LOCK BRAKING SYSTEM (ABS) LIGHT ON SPEEDOMETER MAY BE ERRATIC. DIAGNOSTIC TROUBLE CODE (DTC) C0055 C0235 C0236 OR C0237 STORED IN THE EBCM. *TT 1998-2008 ALL CHEVROLET, GMC, BUICK, AND OLDSMOBILE MID-SIZED TRUCKS AND UTILITIES. 1998-2008 ALL CHEVROLET, GMC, AND CADILLAC FULL SIZED TRUCKS AND UTILITIES. *KB UPDATED ON 09/20/07. *NJ
3528
Service Bulletin/Repair Instructions
REPLACEMENT TWO PIECE PROPSHAFT INFORMATION. VIBRATION WHILE DRIVING. *TT
3691B
Service Bulletin/Repair Instructions
GENERATION III V8 ENGINE PISTON REPAIRS. *TT
3815
Service Bulletin/Repair Instructions
INSTALLING TRAILER WIRING HARNESS WITHOUT THE Z82 OPTION. *TT
4080
Service Bulletin/Repair Instructions
ABS AND TRACTION OFF LIGHTS COMES ON INTERMITTENTLY. *TT UPDATED 03-01-07. *KB
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.