Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIT5161L
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic
PIP5601C
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
07-08-42-006U
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
13-02-32-001H
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
07-08-42-006T
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
03-06-01-023I
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
03-06-01-023H
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
PIT5195H
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
18-NA-094
This service bulletin provides information on Takata Air Bag Courtesy Transportation Reimbursement Program - Applicable to GM Recalls listed in bulletin.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
PIT4322P
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5161K
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
23-NA-224
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
PIP4112T
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
03-06-01-023G
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
07-08-42-006S
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIT3665M
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3227S
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
16-NA-130
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIT4322N
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
07-08-42-006R
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
PIT5161J
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
PIT5082B
This Preliminary Information communication provides information to the technician about vehicle HVAC system does not always respond to requests for changes in air delivery or temperature from the HVAC controls. The technician may find that the HVAC control module will communicate with the scan tool but the HVAC door data actual counts will read 0 counts. The dealer is directed to ensure there is 12V on circuit 300 at HVAC control module before replacing module.
22-NA-205
This service bulletin provides information on Module Harvesting.
PIT3665L
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
10-06-05-002K
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
03-06-01-023F
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
22-NA-149
This informational bulletin provides you with contacts in event of the installation of Cruise control.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT4844K
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
PIT5195G
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
03-06-01-023E
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIT3227R
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
PIT5821C
This Preliminary information communicates information on a parts restrictions for the passenger air bag.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
090604026V
Information.
PIP5276G
This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.
PIT5821B
This Preliminary information communicates information on a parts restrictions for the passenger air bag.
PIT4322M
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
PIT5039E
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube box/hitch, etc. to the rear of the truck, which affects the rear park assist operation. Technician can disable the rear park assist for this concern.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT5821A
This Preliminary information communicates information on a parts restrictions for the passenger air bag.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5039D
This Preliminary Information communication provides information to the technician about vehicles that the customer or up-fitter may have removed the rear bumper, install a different rear bumper, or add a different box/flat bed/cube box/hitch, etc. to the rear of the truck, which affects the rear park assist operation. Technician can disable the rear park assist for this concern.
PIT5403H
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT4322L
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIT4595J
This PI communicates diagnostic tips to help dealership diagnosis a service trailer brake message with DTC C1114 and C1112.
PIT5821
This Preliminary information communicates information on a parts restrictions for the passenger air bag.
PIT3227Q
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
RFI20201207_599-
This SKU is a Climate Control Module. The customer communication requested return of unsold inventory to inspect for a software issue. If the software issue exists it can cause a fan in the climate control system to stay on even when the ignition is turned off. The fan staying on even though the ignition is off can drain the battery, making the vehicle unable to start.
PIT5161H
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3665J
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT5564C
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
PIT5195F
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PIT4322K
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIT4844J
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
PIT4261F
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
PIT5403F
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT5154A
This Preliminary Information communication provides information to the technician explaining what happens when they transition the side view mirrors to curb view mode.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
18NA094
This informational bulletin provides information on Takata Air Bag Completion Rate Improvement Program - Applicable to GM Recalls 14491, 14735, 15040, 15041, 15043, 15044, 15045, 15046, 15047, 15048, 15049, 15050, 15052, 15053, 15406, 15438, 15442, 15815, 15816, 15817, 15818, 15826, 17009, 17476, 17477, 28810, 28811, 17478, 18015 and N192278940.
16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
19NA262
This technical bulletin provides repair information to correct a customer concern of Clock Shows Dashes and Cannot be Set After Battery Disconnect.
DOR-G9Z8V-12
This SKU is a Fuel Pump Driver Module. The customer communication requested return of unsold inventory to inspect the software. The software may have a fault where the readiness monitors are stuck in the not-ready or incomplete position. The readiness monitors will not cause performance or emissions issues but will prevent the emissions scanning tools from confirming the module is performing correctly, causing the vehicle to fail state required emissions tests.
060309004N
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
PIT5161G
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
100605002H
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
16NA338
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP4158H
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
DOR-K2S2K-10
This SKU is a Pitman Arm. The customer communication requested return of unsold inventory to inspect for the spline size. If the spline size is incorrect it will not have a tight fit with the mating component, and would lead to detectable play and/or noise when steering.
DORD8R3N09
This SKU is a Tire Hoist Assembly. The customer communication requested return of unsold inventory to inspect for the shape of the centerpiece of the tire hoist being round when it should be square. If the centerpiece is the incorrect shape then the tire hoist cannot be operated with the OE tools, and the end user would therefore not be able to lower the spare tire with the vehicles original tools.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
090309001G
This technical bulletin provides a procedure for re-torque the lead springs.
090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIT3665H
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT5652E
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac, Pontiac, and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5049E
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
PIT5652D
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
PIT3219F
This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
PIT3665G
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT5652C
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5652B
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
PIT4610F
This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com. or http://www.nfpa.org/
PIT5195E
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PIT5564B
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
PIT5671
This Preliminary information communicates the need for dealers to contact SPAC to obtain qualified parts to repair SIR light on with B0081 SYM4B after replacing PPS kit.
PIP5339A
This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP3119P
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5627
This Preliminary information communicates to the dealer an issue where the vehicle's inspection and maintenance monitors along with diagnostic trouble codes may reset unprompted due to the installation of an aftermarket fuel pump control module.
070845001H
This informational bulletin provides information for aftermarket trailer brake controller added to their vehicle, OR in lieu of the factory integrated trailer brake controller (ITBC) (RPO JL1).
110849001Y
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
PIT5652A
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised to contact General Motors TAC for further instructions for a temporary repair until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3227P
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
070842006N
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT4250J
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT5570B
This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed.
PIT4573E
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles that may have a no crank concern. Technician will find Diagnostic Trouble Codes in the Power Control Module P1AAB, P1AAC, P1AAD, and/or P1AAE set. Technician will perform a visual inspection for arcing at the cable to stator connections must be performed first by removing the cables from the stator. If there are signs of arcing, replace both components.
PIT3946C
This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.
PIP4138R
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT4322J
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIT5403E
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT4844H
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
PIT4745E
This Preliminary Information communication provides information to the technician about vehicles that have raised dents or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
PIP3366C
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
PIT3219E
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
PIT5195D
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PIP4112S
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
PIT4376J
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.
PIT5049D
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
PIP4138Q
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT3665F
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIP3343F
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIP4578B
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
PIT4844G
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
130232001E
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
090309001E
This technical bulletin provides a procedure for retorque the lead springs.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
070232008B
This technical bulletin provides a procedure to torque to tighten analysis to correct a steering wheel is out of position (turned to the left or right) while driving straight ahead and/or a clunk noise while turning with early front tire wear concern that is caused by the threaded joint between the inner tie rod and the rack loosening.
09-08-66-011C
Information on Mounting Points for Pickup Box Accessories
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
15NA082
This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps.
PIT4250H
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT4261E
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
PIT4730B
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT3946B
This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001.
PIT5161F
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
PIT5570A
This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed.
PIC5650C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIT4745D
This Preliminary Information communication provides information to the technician about vehicles that have raised dents or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
PIT5403D
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
PIT4322H
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
PIT5564A
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
PIP4112R
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
PIT5049C
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIT4745C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE RAISED DENTS OR RIPPLE APPEARANCE IN THE SIDE OUTER PANEL OF THE CARGO BOX AROUND THE PERIMETER OF THE WHEEL HOUSE OPENING. TECHNICIAN SHOULD FIRST ACCESS THE REAR OF THE INNER WHEELHOUSE AREA THROUGH THE TAIL LAMP CAVITY AND THE FRONT OF THE WHEELHOUSE FROM UNDER THE VEHICLE, AND COAT THE INNER HEM OF THE WHEEL HOUSE TO SIDE OUTER PANEL WITH 3M RUST FIGHTER I. AFTER ALLOWING THE 3M RUST FIGHTER I TO DRY THEN APPLY SEVERAL COATS OF NOX RUST X-121B UNDERCOATING PART NUMBER 12346501.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
16NA241
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
PIT4780S
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE PART RESTRICTION FOR THE PARALLEL HYBRID TRUCK PARTS LISTED BELOW HAS ENDED. DEALER CAN ORDER PART THROUGH THE NORMAL PART PROCESS.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
PIT5403B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS TO DIAGNOSIS AND REPAIR VEHICLES WITH VARIOUS HANDLING, VEHICLE DYNAMICS CONCERNS, NOISES FROM THE SUSPENSION OR UNDERBODY, OR ISSUES RELATED TO DAMAGED SUSPENSION COMPONENTS. BEFORE ANY IN-DEPTH DIAGNOSTICS ARE PERFORMED, BE AWARE THAT VARIOUS ISSUES COULD OCCUR IF THE VEHICLE HAS BEEN MODIFIED AND INFORM THE CUSTOMER THE CONDITIONS NOTED MAY NOT BE COVERED UNDER WARRANTY. TECHNICIAN WILL INSPECT FOR INSTALLED AFTERMARKET SUSPENSION COMPONENTS. ALSO INSPECT FOR IMPROPERLY ADJUSTED TORSION BARS.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
49151
49151 - Engineering Study - Your dealership may have been previously advised of being selected to participate in an engineering study to test and evaluate Takata front passenger air bag inflators. The purpose of the engineering study is to obtain a statistically relevant sample of front passenger air bag inflator modules from certain 2007 and 2008 model year vehicles.
00-03-10-006M
THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT.
16-NA-215
THIS TECHNICAL BULLETIN PROVIDES A PROEDURE TO REPLACE THE DOOR PANELS WITH NEWLY DESGINED PARTS FOR VEHICLES WITH THE CONDITION OF A BROKEN TRIM PANEL AROUND DOOR HANDLE.
07-03-10-008E
THIS INFORMATIONAL PROVIDES INFORMATION ON SLIGHT OR MILD TIRE FEATHERING AND RECOMMENDED PRACTICES.
15-08-44-001H
THIS INFORMATIONAL BULLETIN PROVODES INFORMATION ON THE GM OF CANADA ONSTAR CELLULAR COMMUNICATION UPGRADE.
04-00-89-015M
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES POLICY INFORMATION ON USING GM SERVICE POLICIES AND PROCEDURE MANUAL THAT REPRESENT KEY GM REQUIREMENTS FOR SERVICE OPERATIONS.
PIT-3665-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HYDRO-BOOST IS NOT SERVICEABLE AND WILL NEED TO BE REPLACED IF THE BRAKE PEDAL MOVES OR APPLIES ON ITS OWN AT A FULL TURN.
SB-16-NA-130
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO INSPECT THE UPPER VALVE BODY TO DETERMINE THE CORRECT RPO USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIT-5485-B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIT-5161-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN. CUSTOMER HEARS A CLUNK WHEN STOPPING OR LAUNCHING.
PIT5161D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN. CUSTOMER HEARS A CLUNK WHEN STOPPING OR LAUNCHING.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-09-03-09-001D
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO RE-TORQUE THE JOINTS OF THE REAR LEAF SPRING ASSEMBLY TO CORRECT A CUSTOMER CONCERN OF A CLUNKING NOISE COMING FROM THE REAR OF THE VEHICLE.
PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
SB-01-06-01-028C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A ENGINE KNOCK ON COLD START.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
SB-06-06-05-001G
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON CHANGES IN EXHAUST TONE FOR ACTIVE FUEL MANAGEMENT ENGINES WHEN IN THREE OR FOUR CYLINDER MODE.
SB-PI-1533B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION ON POOR RADIO HANDS-FREE VOICE RECOGNITION PERFORMANCE OR SOUND QUALITY AFTER THE ONSTAR UPGRADE.
14520A
14520A - SPECIAL COVERAGE (REVISED TO INCLUDE 2007, AND 2010-2013 MODEL YEAR CHEVROLET SILVERADO AND GMC SIERRA LIGHT DUTY TRUCKS, ALONG WITH EXPANDING COVERAGE TO CERTAIN U.S. STATES). SOME 2008-2009 MODEL YEAR CHEVROLET SILVERADO AND GMC SIERRA LIGHT-DUTY VEHICLES REGISTERED IN CANADA OR 2007, AND 2010-2013 MODEL YEAR CHEVROLET SILVERADO AND GMC SIERRA LIGHT DUTY VEHICLES REGISTERED IN OR PREVIOUSLY REGISTERED IN MAINE, NEW HAMPSHIRE, NEW YORK, AND VERMONT OR IN THE CANADIAN PROVINCES NEW BRUNSWICK, NEWFOUNDLAND, NOVA SCOTIA, PRINCE EDWARD ISLAND, ONTARIO, AND QUEBEC MAY DEVELOP A FRACTURED MIDDLE-LEAF SPRING IN THE THREE-LEAF REAR-SUSPENSION SPRING ASSEMBLY, FORWARD OR REARWARD OF THE JOINT TO THE REAR AXLE. THIS CONDITION MAY RESULT IN NOISE, RIDE-HEIGHT DIFFERENCE, CONTACT WITH A REAR TIRE, AND/OR DAMAGE TO OTHER COMPONENTS UNDER THE VEHICLE. VEHICLES WITH THIS CONDITION WILL HAVE REDUCED LOAD-CARRYING CAPACITY. IF THE CONDITION OCCURS WITHIN THE TERM LIMITS, DEALERS WILL REPLACE THE REAR SPRINGS.
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
PIT4211D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE AN OUTSIDE AIR TEMPERATURE INOPERATIVE. TO PERFORM AN INSTANT UPDATE OF THE AMBIENT TEMPERATURE SENSOR, PRESS AND HOLD THE RECIRC BUTTON AND AIR CONDITIONING BUTTON ON THE HEATER-VENT-AIR CONDITIONING CONTROL HEAD SIMULTANEOUSLY. IT IS ALSO POSSIBLE TO PERFORM THIS BY USING A SCAN TOOL IN SPECIAL FUNCTION MODE AND SELECT INSTANT UPDATE.
PIT4573D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A NO CRANK CONCERN. TECHNICIAN WILL FIND DIAGNOSTIC TROUBLE CODES IN THE POWER CONTROL MODULE P1AAB, P1AAC, P1AAD, AND/OR P1AAE SET. TECHNICIAN WILL PERFORM A VISUAL INSPECTION FOR ARCING AT THE CABLE TO STATOR CONNECTIONS MUST BE PERFORMED FIRST BY REMOVING THE CABLES FROM THE STATOR. IF THERE ARE SIGNS OF ARCING, REPLACE BOTH COMPONENTS.
06-08-50-009I
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
PIP-5258
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE SERVICE ENGINE SOON AND A DIAGNOSTIC TROUBLE CODE P0011. IF THE TECHNICIAN HAS FOLLOWED SERVICE INFORMATION DIAGNOSTIC TROUBLE CODE FOR P0011AND THE ROOT CAUSE WAS NOT FOUND THE OIL PRESSURE AT THE OIL PRESSURE SENDER SHOULD BE CHECKED. ALSO THE NUMBER 2 CAM BEARING SHOULD BE INSPECTED.
PIT4780R
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
130232001D
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
09184C
09184C - CUSTOMER SATISFACTION PROGRAM (REVISED SERVICE PROCEDURE). THIS BULLETIN HAS BEEN REVISED TO CLARIFY STEP 5 OF THE SERVICE PROCEDURE. CERTAIN 2007-2009 MODEL YEAR CHEVROLET SILVERADO AND GMC SIERRA VEHICLES CURRENTLY OR PREVIOUSLY REGISTERED IN ALASKA, CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN MAY HAVE A CONDITION IN WHICH THE SENSING AND DIAGNOSTIC MODULE (SDM) MAY CORRODE DUE TO A SIGNIFICANT QUANTITY OF SNOW AND/OR WATER CONTAINING ROAD SALT OR OTHER CONTAMINANTS ENTERING THE VEHICLE AND SATURATING THE ACOUSTICAL PADDING BENEATH THE CARPET. THE SDM IS LOCATED UNDER THE DRIVERS SEAT BENEATH THE ACOUSTICAL PADDING. IF SUFFICIENT MOISTURE COLLECTS AND IS RETAINED IN THE PADDING, IT MAY CAUSE EXCESSIVE CORROSION UNDER THE SDM THAT COULD COMPROMISE THE MODULE SEAL AND ALLOW WATER INTRUSION THAT COULD RESULT IN SDM MALFUNCTION. IF THIS CONDITION EXISTS, THE AIRBAG READINESS LIGHT OR A SERVICE AIRBAG" MESSAGE ON THE DRIVER INFORMATION CENTER (DIC) MAY ILLUMINATE. IN RARE CASES, THE VEHICLE MAY CONTACT ONSTAR® AND THE SEAT BELT PRETENSIONERS OR FRONT AIRBAGS MAY DEPLOY. DEALERS ARE TO REMOVE THE ACOUSTICAL PAD ABOVE THE SDM, INSPECT THE SDM, AND REPLACE THE SDM, IF NECESSARY.
02-06-01-022P
Information on Diesel Engine Ticking Noise
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
08-06-04-003D
New Tool Availability EN-48974 EGR Cooler Pressure Tester Adapter Set to Diagnose Duramax® Diesel Engine EGR Cooler Engine Coolant Leaks into Combustion Chamber
10-06-05-002B
CLEAN EXHAUST FILTER SEE OWNERS MANUAL NOW or CLEANING EXHAUST FILTER KEEP DRIVING UNTIL MESSAGE IS CLEARED Displayed on DIC, DTC P2463 May Be Set
15-NA-079
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
15-NA-082
Clunking Noise from Front of Vehicle During Turns and/or Bumps Some customers may comment on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket
15NA082B
Clunking Noise from Front of Vehicle During Turns and/or Bumps
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
01-06-01-011I
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
15-06-03-001A
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
05-03-07-009H
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
06-06-01-007I
This informational bulletin provides information to dealership personnel on identifying Duramax Diesel overpower engine breakdown or non-function due to aftermarket power-up devices vs. non overpower engine non-function of pistons, cylinders, valve train components, and DTC P003A or P111D set.
PI0652B
This preliminary informational bulletin provides technicians with repair information on removing seized exhaust temperature sensors.
PIC5491G
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
SB-07-06-04-019A
GENERAL MOTORS: INTERMITTENT MIL/SES/ DTC P2138 WITH REDUCED ENGINE POWER (REPAIR INSTRUMENT PANEL (IP) TO BODY HARNESS CONNECTOR). 2005-08 GM PASSENGERS CARS/LIGHT DUTY TRUCKS (INCL. SATURNS). *PE UPDATED 11/5/10. *PE UPDATED 4/4/11. *PE UPDATED 2/3/16. *PE
SB-10-08-42-001A
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/SATURN: LOW BEAM HEADLAMP BULB DIAGNOSIS/REPLACEMENT (INSPECT BULB AND CONNECTOR). DOES NOT APPLY TO VEHICLES EQUIPPED WITH HIGH INTENSITY DISCHARGE (HID) LAMPS. DO NOT REPLACE THE ENTIRE HEADLAMP ASSEMBLY FOR THIS CONDITION. *PE
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
05-03-10-020F
This informational bulletin communicates GM's position on use of nitrogen gas in tires.
05-08-51-001G
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.
01-00-89-010K
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).
06-08-47-001K
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
00-03-10-002I
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.
11-01-39-005B
This technical bulletin provides a procedure to correct a customer concern of reduced heater performance with winter grille cover installed.
PIP4568R
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. TECHNICIAN WILL FOLLOW SERVICE INFORMATION DIAGNOSIS FIRST. IF SERVICE INFORMATION DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN PERFORM A CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT SYSTEM COMPRESSION TEST IN SERVICE INFORMATION. IF THE RUNNING COMPRESSION OF THE MISFIRING CYLINDER STAYS BELOW 25 POUNDS PER SQUARE INCH REGARDLESS OF THE ACTIVE FUEL MANAGEMENT SOLENOID BEING COMMANDED ON OR OFF, AN ACTIVE FUEL MANAGEMENT LIFTER IS MECHANICALLY COLLAPSED/STUCK OR UNLOCKING AS SOON AS THE ENGINE IS STARTED. REPLACE ALL ACTIVE FUEL MANAGEMENT LIFTERS, AND ALL PLASTIC LIFTER GUIDES. ALSO PERFORM THE CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT VALVE LIFTER OIL MANIFOLD DIAGNOSIS AND TESTING IN SERVICE INFORMATION. IF IT ISOLATES A CONCERN WITH THE VALVE LIFTER OIL MANIFOLD, REPLACE IT AND REEVALUATE THE CONCERN. THE ACTIVE FUEL MANAGEMENT LIFTERS CAN ALSO BE MONITORED FOR PROPER OPERATION BY CAREFULLY INSPECTING THE CYLINDER 1, 4, 6, AND 7 ROCKERS AND VALVES WHILE CRANKING OR BRIEFLY AND SAFELY RUNNING THE ENGINE WITH THE VALVE COVERS REMOVED. IF THE VALVE OR VALVES OF AN ACTIVE FUEL MANAGEMENT CYLINDER STOP MOVING WHILE DOING THIS TEST, THE ACTIVE FUEL MANAGEMENT LIFTER IS CAUSING THE CONCERN. FOR 2008-2009 FULL SIZE TRUCK/SUV OR A 2007-2009 CHEVROLET TAHOE WITH THE POLICE PACKAGE REPROGRAM THE ENGINE CONTROL MODULE. ON THE 2008-2009 PONTIAC G8, 2010-2011 CAMARO, AND 2007-2010 FULL SIZE TRUCKS WITH ACTIVE FUEL MANAGEMENT, ALSO DETERMINE IF THE ACTIVE FUEL MANAGEMENT PRESSURE RELIEF VALVE SHIELD THAT IS LISTED IN THE LATEST VERSION OF 10-06-01-008 HAS EVER BEEN INSTALLED. ON PASSENGER CARS WITH THE LS4 ENGINE, DETERMINE IF THE UPDATED OIL PAN GASKET THAT IS LISTED IN THE LATEST VERSION OF 11-06-01-007 HAS BEEN INSTALLED.
07-06-03-009D
This informational bulletin adds models to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PI1391
This preliminary informational bulletin provides a diagnostic tip for coolant leak at oil cooler inlet pipe o-ring after service engine replacement.
03-06-03-003D
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
11-00-89-004A
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).
PIC3278F
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.
07-06-03-009C
This informational bulletin adds 2011 - 2014 model years to information on voltmeter gauge fluctuation due to regulated voltage control system and concerns about camper/trailer battery charging.
09-06-04-026J
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).
PI0360E
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application.
03-00-91-001G
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
030729004I
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
PI0655A
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
1008110001C
This information provides the proper way to install the floor mats .
100089005D
This warranty informational bulletin advised the technician that when performing a wiring repair, more information is required.
14515
Chassis Electronic Control Module Internal Contamination
PIT5074H
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
G-204625
09184B - CUSTOMER SATISFACTION (REVISED VEHICLE POPULATION, CONDITION STATEMENT AND SERVICE PROCEDURE). CERTAIN VEHICLES CURRENTLY OR PREVIOUSLY REGISTERED IN ALASKA, CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN MAY HAVE A CONDITION IN WHICH THE SENSING AND DIAGNOSTIC MODULE (SDM) MAY CORRODE DUE TO A SIGNIFICANT QUANTITY OF SNOW AND/OR WATER CONTAINING ROAD SALT OR OTHER CONTAMINANTS ENTERING THE VEHICLE AND SATURATING THE ACOUSTICAL PADDING BENEATH THE CARPET. THE SDM IS LOCATED UNDER THE DRIVERS SEAT BENEATH THE ACOUSTICAL PADDING. IF SUFFICIENT MOISTURE COLLECTS AND IS RETAINED IN THE PADDING, IT MAY CAUSE EXCESSIVE CORROSION UNDER THE SDM THAT COULD COMPROMISE THE MODULE SEAL AND ALLOW WATER INTRUSION THAT COULD RESULT IN SDM MALFUNCTION. IF THIS CONDITION EXISTS, THE AIRBAG READINESS LIGHT OR A SERVICE AIRBAG" MESSAGE ON THE DRIVER INFORMATION CENTER (DIC) MAY ILLUMINATE. IN RARE CASES, THE VEHICLE MAY CONTACT ONSTAR® AND THE SEAT BELT PRETENSIONERS OR FRONT AIRBAGS MAY DEPLOY. DEALERS ARE TO REMOVE THE ACOUSTICAL PAD ABOVE THE SDM, INSPECT THE SDM, AND REPLACE THE SDM, IF NECESSARY.
09184B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5066A
Intermittent Battery Draw Dead Battery Or HVAC Odor.
PIT5099A
A/C Blows Warm Or Poor Performance.
PIT5195B
Speedometer Needle Accuracy Information.
PIT5264B
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
PIT5353
XM Audio Traffic And Travel Link Availability And Operation.
06-03-09-004F
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
05-06-04-022K
This informational bulletin provides information on top tier fuels and what brands are available.
07-08-42-006J
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer
10-06-01-008K
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CORRECT THE CUSTOMERS CONCERN TO REPLACE THE LEFT SIDE VALVE COVER AND ACTIVE FUEL MANAGEMENT OIL DEFLECTOR TO REDUCE OIL CONSUMPTION.
PI0652A
THIS PRELIMINARY BULLETIN PROVIDES A INFORMATION ON HOW TO REMOVE THE SEIZED TEMPERATURE SENSORS FROM THE DPF.
130522001B
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
08-06-04-003C
This informational bulletin advises of a new testing tool for EGR cooling pressure tester.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
SB-13-02-32-001
BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE
PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
14-06-04-005
This information bulletin advises of a new tool used to aid in installing Duramax glow plugs.
Recalls
Vehicle Recalls
050308002F
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
PI1266
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.
PI0373B
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
PIC5088E
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
05-00-89-029C
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
03-00-89-006K
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
PI1257
This preliminary bulletin provides a procedure to install a new design upper intake manifold with a new MAP sensor relocated to prevent ice build up and setting code P0106.
PI257
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4813E
Service Charging System Message Or Low Volt Gauge Reading After Cold Start
PIT4813F
Service Charging System Message Or Low Volt Gauge Reading After Cold Start.
PIT5209A
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
PIT5297
Reduced Air Flow From HVAC Vents.
03-06-03-004L
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
00-03-10-006J
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
03-03-10-007I
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
13-00-89-004I
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
06-00-89-029J
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
06-06-05-001F
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines when in Three or Four Cylinder Mode
130089004I
Car and Truck Fix it Right the First Time Issues
1406130001
High Voltage Safety ? High Voltage Disabling
PIT4780P
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5161B
Bump Feel Or Clunk Noise After A Stop.
10-06-05-002A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIT5039C
Removing / Disabling Rear Park Assist RPO UD7.
PIT5264
Canadian Customers Unable To Place Calls In The United States
090730004J
Slips in Reverse or Third, Delayed Reverse or Drive Engagement, DTC P0776, P2715,P2723, Harsh 2-3 Shifts (Inspect 1-2-3-4 / 3-5-R Housing and Pump Seal Rings)
120310002A
Proper Wheel Installation and Wheel Torque Techniques
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIP4885H
NQG 4WD Models With Noise Vibration On Dry Pavement.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PIP4885G
NQG 4WD Models With Noise Vibration On Dry Pavement.
130522001
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
PIC5932
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5491D
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIT4729E
Adding Integrated Trailer Brake Controller RPO JL1.
PIT4844E
Adding Cruise Control (RPO K34)
4112
SAG OR HESITATION ON ACCELERATION (NORMAL OPERATING CHARACTERISTICS). EQUIPPED W/ GASOLINE ENGINE AND AUTOMATIC TRANSMISSION. *NJ UPDATED 1/30/08. *NJ UPDATED 10/01/08. *PE UPDATED 8/12/09. *PE UPDATED 9/23/13. *PE UPDATED 11/12/13. *PE
130232001B
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
130232001A
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
PIP4365D
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4417H
Swapping Outside Rearview Mirrors RPOs DL8 / DL3 / DPN.
00-05-22-002N
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
02-07-30-052I
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
08-06-01-006D
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
PI0639B
This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor operation information.
02-08-98-002D
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
11-00-90-001B
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
09-00-89-008A
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
07-03-10-015C
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.
05-08-48-001C
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
05-03-07-009F
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.
13-00-89-004B
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
06-00-89-026K
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.
09-07-30-018D
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.
10-00-89-005C
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
07-00-89-037F
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
09-00-89-016C
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
PI0718B
This preliminary informational bulletin provides a revision of PI0718A to add model years and update the Warranty Information.
070847004
INFORMATION ON BODY CONTROL MODULE (BCM) GROUNDS. *NJ UPDATED 7/19/13. *PE
130232001
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
PIT5074G
Terminal Test Probe And Replacement Terminal.
PIT5215
GM Accessory Heated Seats Inoperative After Installation.
120421001B
Transfer Case Identification First Design vs. Second Design
PIT4780M
Parallel Hybrid Truck (PHT) Part Restriction.
PIT5208
Fuel Gauge Shows Empty After Refueling And DTC P2636.
PIT5209
Unwanted Alarm Sounding (GM Accessory Inclination Sensor Mounting)
1308116001A
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
PIT4474D
Navigation or Radio Display Blank Or Flashing DTC B1265 B1288 Or B1289.
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
120232001A
Hydraulic Power Steering Leak at Hose Connection to Steering Rack
120601007A
New Service Cam Bearings For Gen IV V8 Engines
PIT4605D
Cold Air Leak On Passenger Floor.
PIT5201
Driver or Passenger Door Module DTC B2555.
08-08-48-003G
This technical bulletin provides a procedure for adding double sided tape on the right and left windshield side reveal moldings to remove tapping, clicking or ticking type noise.
PIT5195
Speedometer Needle Accuracy Information
11-00-90-001A
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
PI0648A
This preliminary informational bulletins provides information regarding the release of a new designed HVAC blower motor assembley. The bulletin provides information on how to correctly install the parts to function as intended.
11-00-89-005C
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PI0876
This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PI0383B
This preliminary information bulletin provides information on installing new rivets on the accessory tonneu cover to correct a customers comments on the cover seeming loose
12-03-10-003
This informational bulletin provides the proper information used to determine the road force variences within new tires being installed and the proper forms used to send the tires back if the road force is not within spec.
120310002
Proper Wheel Installation and Wheel Torque Techniques
120310003
Diagnostic Tips for Difficult to Resolve Tire/Wheel Vibration Concerns
SB-12-03-10-003
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-08-44-015C
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4801E
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIP3720D
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
PIT4907A
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT4208D
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
PI0695A
Diagnosis and Repair HVAC Blower Function.
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
SB-07-08-42-006H
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
07-08-42-006G
This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box Removed
08-06-04-006K
This informational bulletin provides information for Identifying Non-GM ECM Calibration Use and Power-up Hardware Detection in Duramax Diesel Engines - Photograph Tech 2 Calibration IDs, Calibration Verification Numbers (CVNs) and Transmission Data Screen
080604006K
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IDENTIFYING NON-GM ECM CALIBRATION USE AND POWER-UP HARDWARE DETECTION IN DURAMAX DIESEL ENGINES - PHOTOGRAPH TECH 2 CALIBRATION IDS, CALIBRATION VERIFICATION NUMBERS (CVNS) AND TRANSMISSION DATA SCREEN
09-07-30-018C
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
12-00-89-007
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
PI0373A
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
PIT3237F
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
11-00-89-005B
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
07-00-89-037E
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM.
10-00-89-017V
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
PIP4885E
NQG 4WD Models With Noise Vibration On Dry Pavement
PIP4885F
Vibration On Dry Pavement.
PIT-4508
CRUISE CONTROL INOPERATIVE - KEYWORDS ABS B3894 BRAKE CYLINDER EBCM INOP MASTER MODULE PRESSURE SENSOR SWITCH TRAILER. WITH RPO JL1. *NJ MODELS 2007-2013 AVALANCHE, SILVERADO, SUBURBAN, TAHOE SIERRA, YUKON, YUKON DENALI, YUKON XL, YUKON DENALI XL. UPDATED 12/10/12. *PE
PIT4508C
Cruise Control Inoperative.
PIT5184
Various Concerns Related To The IP Backlighting Cruise Control Steering Wheel Controls Horn.
PIT5185
Computer-Controlled Cranking System (Bump Start) Inoperative.
SB-07-08-42-006G
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-10-06-01-008F
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4322F
Unwanted Stability Activation And/Or C0710.
PIT5049A
Rattle Squeak Clunk Bump Noise From Front Suspension.
PIT5120A
Stabilitrak/Traction Control OFF With Red Brake Warning Lamp
PIT5182
Radio Button Backlighting Inoperative.
PIT-3749D
GM: ON SOME TRUCK MODELS THERE IS SOME FRAME CORROSION. *RM UPDATED ON 5/2/2012. *KB
PIT-4056
GMC: UNABLE TO COMMUNICATE WITH THE EBCM DTC U0121. *NJ VEHICLES EQUIPPED WITH JL4. UPDATED 9/30/08. *PE UPDATED 6/27/11. *PE UPDATED 4/6/12. *PE
SB-09-06-03-004A
GM/HUMMER/SAAB: INTERMITTENT ILLUMINATION OF MIL, SERVICE LAMPS, SERVICE MESSAGES, OR DTC SET BY VARIOUS CONTROL MODULES-DIAGNOSING AND REPAIRING FRETTING CORROSION (DISCONNECT AFFECTED CONNECTOR AND APPLY DIELECTRIC LUBRICANT). *PE UPDATED 3/26/10. *PE UPDATED 6/6/11. *PE UPDATED 3/12/12. *PE
05-09-40-002E
GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE
PIT 4162
SERVICE STABILITY LAMP DTC C0131. *NJ UPDATED 4/1/08. *NJ UPDATED 6/26/08. *NJ UPDATED 12/18/08. *PE UPDATED 8/1/11. *PE
PIP4365
TRANSFER CASE WILL NOT SHIFT POSSIBLE DTC'S C0387 AND/OR C0569. ON VEHICLES EQUIPPED WITH A MAGNA TRANSFER CASE RPO NQF. *NJ UPDATED 3/15/10. *PE UPDATED ON 6/27/2011. *KB
PIT4193
P245/70R17 GENERAL AMERITRAC TIRE WEAR VIBRATION. *KB UPDATED 12/13/07. *NJ UPDATED 1/30/08. *NJ UPDATED 5/25/11. *PE
3189
UNABLE TO DISABLE AUTO DOOR LOCKS. THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. *PE UPDATED 5/9/11. *PE
SB-10-06-01-008
CADILLAC/CHEVROLET/GMC/PONTIAC: ENGINE OIL CONSUMPTION ON ALUMINUM BLOCK ENGINES WITH ACTIVE FUEL MANAGEMENT (AFM) (INSTALL AFM OIL DEFLECTOR AND CLEAN CARBON FROM CYLINDER). CAUSED BY AN UNCOVERED AFM VALVE THAT SPRAYS OIL ON THE BOTTOM OF THE CYLINDERS WHEN THE VEHICLE IS IN FOUR CYLINDER MODE. *PE UPDATED 5/9/11. *PE
070232002
EI07082 - POWER STEERING FLUID LEAKING FROM POWER STEERING GEAR/RACK ASSEMBLY. *KB UPDATED ON 09/21/07. *NJ UPDATED 10/5/07. *NJ UPDATED 2/15/08. *NJ UPDATED 5/19/08. *NJ UPDATED 2/17/10. *PE UPDATED 3/30/11. *PE
4225
SERVICE STABILITY LAMP DTC C0710. *NJ UPDATED 3/25/11. *PE
PIT4366
[CHECK TRAILER WIRING] MESSAGE DISPLAYED ON DIC. WITH RPO JL1. *NJ UPDATED 3/28/11. *PE
PIT4595
SERVICE TRAILER BRAKE MESSAGE WITH DTC C1114 AND/OR C1112. WITH RPO JL1. *NJ UPDATED 3/28/11. *PE
PIE-0043
CHEVROLET:GMC: ENGINEERING INFORMATION-FUEL TANK PRESSURE SENSOR, DTCS P0446, P0451 OR P0454 SET. GMC ENGINEERING IS ATTEMPTING TO DETERMINE THE ROOT CAUSE OF THE ABOVE CONCERN. *PE
02-06-04-037
SOME CUSTOMERS WHOSE VEHICLES ARE OPERATED IN DUSTY TYPE ENVIRONMENTS, SUCH AS FARMING OR MINING OFF-ROAD TYPE APPLICATIONS, MAY COMMENT ABOUT THE ILLUMINATION OF THE INSTRUMENT PANEL SES LIGHT, WITH DIAGNOSTIC TROUBLE CODE P0446 SET. *TT UPDATED 7/11/08. *NJ UPDATED 11/5/10. *PE
07293
CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. TRANSMISSION OVERHEAT IN EXTREME COLD AMBIENT TEMPERATURES - REPROGRAM TCM. LOCATED IN ALASKA AND MINNESOTA; CANADIAN YUKON AND NORTHWEST TERRITORIES ONLY. *NJ CSC WAS RECEIVED. UPDATED 3/13/08. *NJ UPDATED 4/24/08. *NJ UPDATED 7/8/09. CSC LETTER WAS RECEIVED. *PE
08142
CHEVROLET SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ECM EEPROM - REPROGRAM ECM. ALL 2007 AND CERTAIN 2008 CHEVEROLET SILVERADO AND EXPRESS AND GMC SIERRA AND SAVANA EQUIPPED WITH 6.6L DURAMAX VA DIESEL (RPO LMM - VIN 6) ENGINE. CSC WAS RECEIVED. *PE UPDATED 5/5/09. CSC LETTER WAS RECEIVED. *PE
PIT4046
SERVICE BRAKES SOON MESSAGE DTC C0299. *NJ UPDATED 5/13/08. *NJ UPDATED 12/5/08. NO HYBRIDS VEHICLES. *PE
4322
UNWANTED STABILITY ACTIVATION AND/OR C0710 WITH LIFT/LOWER KITS-DIFFERENT TIRES/WHEEL. WITH RPO JL4. *NJ UPDATED 12/18/08. *PE
PIP-4395
GMC: FLARE AND OR HARSH 2-3 SHIFTS. THIS CONDITION MAY BE CAUSED BY LEAKING 1-2-3-4 AND 3-5-R CLUTCH FLUID SEAL RINGS (230). MODELS CADILLACS, CHEVROLETS, GMC, HUMMERS, PONTIACS. EQUIPPED WITH 6L80 (RPO MYC) OR 6L90 (RPO MYD) AUTOMATIC TRANSMISSION. *PE
4169
SERVICE STABILITY LAMP DIAGNOSTIC TROUBLE CODE (DTC) C0561. *KB UPDATED 9/30/08. *PE
4294
FUEL GAUGE ERRATIC IN FREEZING TEMPERATURES P0463. *KB WITH ONE OF THE FOLLOWING ENGINE RPO'S: LY2, LY5, LY6. LH6, L76, L92. UPDATED 1/30/08. *NJ UPDATED 12/5/08. *PE
060941004
PASSENGER SIDE AIRBAG DOOR DOES NOT FLUSH WITH DASH PAD/WARPED. (REPOSITION LOCKING TABS ON AIRBAG PANEL). *KB UPDATED 10/5/07. *NJ UPDATED 9/12/08. *PE
3009
SUSPENSION VIBRATION OR FRAME BEAMING AT 40 - 60 MPH. *KB UPDATED 8/25/08. *PE
PIT4604
TURN SIGNALS FLASH FAST AFTER FACTORY BOX REMOVED. *NJ UPDATED 8/25/08. *PE
PIP4307
SES LIGHT ON DUE TO DTC P0101 AND/OR P0106 - INSPECT AIR FILTER AND/OR MAP SENSOR . WITH 6.6L DIESEL ENGINE (RPO, LBZ, LLY, OR LMM). *NJ UPDATED 5/13/08. *NJ
PIP4348
DURAMAX DIESEL DPF REGENERATION CHANGES - VEHICLES EQUIPPED WITH THE 6.6 DURAMAX DIESEL ENGINE RPO CODE LMM. *NJ
08-06-04-016
DIAGNOSTIC INFORMATION ON MIL/SES WITH DTC P0171 (FUEL TRIM SYSTEM LEAN BANK 1) AND/OR P0174 (FUEL TRIM SYSTEM LEAN BANK 2) AFTER BRAKE MASTER CYLINDER REPLACEMENT. *NJ
08-08-45-002
LEFT OR RIGHT POWER OUTSIDE MIRROR INOPERATIVE (INSPECT WIRE HARNESS). *NJ
PIP3605
DTC U0101, NO ENGINE CRANK AND NO TECH II COMMUNICATION WITH TCM. EQUIPPED WITH ALLISON LCT1000 (RPO-MW7) AUTOMATIC TRANSMISSION. *NJ
PIT4411
UNWANTED ABS OR VALVE ACTIVATION ON LOW SPEED TURNS. *NJ
PIP3343
POSSIBLE ENGINE OIL LEAK DUE TO PCV FREEZE-UP, EQUIPPED WITH THE 4.8, 5.3, 6.0, AND 6.2 V-8 ENGINES. *NJ
PIP4054A
EATON LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS, EQUIPPED WITH A LOCKING REAR DIFFERENTIAL RPO G80. *NJ UPDATED 7/17/2008. *PE
PIP4105
DURAMAX DIESELS WITH DTC P009E, VEHICLES EQUIPPED WITH THE 6.6 DURAMAX DIESEL ENGINE RPO CODE LMN. *NJ UPDATED 4/7/08. *NJ
PIP4219
DIAGNOSIS FOR SERVICE FAST LEARN ADAPTS FAILS, NO FORWARD OR NO REVERSE. *NJ UPDATED 4/1/08. *NJ
PIP4321
OIL LEAK AT REAR OF ENGINE. EQUIPPED WITH A 4.8, 5.3, 6.0 OR 6.2 V8 ENGINE. *NJ
PIP4344
SHORT DURATION COLD START LIFTER TICK NOISE. EQUIPPED WITH THE 5.3 OR 6.0 ACTIVE FUEL MANAGEMENT ENGINES. *NJ
PIT3569
LOW TIRE LIGHT ON AND/OR DIC CHECK TIRE PRESSURE MESSAGE WHEN COLD, WITH RPO UJ6. *NJ
PIT4284
ENGINE STALLS AFTER BEING REMOTE STARTED. *NJ
PIT4316
CHECK LOW TIRE / AFTERMARKET WHEELS / TIRE PRESSURE MONITOR / FMVSS 138 WITH (RPO UJ6). *NJ
05-04-21-003
SERVICE 4WD LIGHT ILLUMINATED, DIAGNOSTIC TROUBLE CODE (DTC) C0374 SET. *TT UPDATED 10/05/07. *NJ INSPECT WIRING HARNESS TO TRANSFER CASE SPEED SENSORS, REPLACE WIRING HARNESS. UPDATED 7/18/08 *PE
070849029
INSTRUMENT PANEL (IP) GAUGES/GAGES DIFFICULT TO READ OR SEE, POOR BACKLIGHTING (REPLACE IP AND PROGRAM). *NJ
4011
AIR BAG INDICATOR LIGHT IS ON. *KB UPDATED ON 12/13/07. *NJ
4512
OUTSIDE DOOR HANDLE LOOSE, INOPERATIVE OR DOES NOT RETRACT. *NJ
3808
CRANK NO START, ROUGH RUNNING, OR DTC P0335. *TT EQUIPPED WITH 5.3L, 6.0L, 6.2L ENGINES. UPDATED 1/30/08. *NJ
3917
ENGINE HAS LOW POWER ON ACCELERATION OR WHEN TOWING. EQUIPPED WITH THE 6.0L LY6 AND L76 ENGINE. *NJ UPDATED 1/29/08. *NJ
4132
SIR LIGHT ON, DTC'S B0085, B0086, B0087 AND B0088. *NJ
4143
U0106 LOSS OF COMMUNICATION WITH GLOW PLUG CONTROL MODULE. EQUIPPED WITH THE 6.6L DURAMAX DIESEL ENGINE RPO CODE LMM. *NJ
4147
DURAMAX DIESELS WITH SES LIGHT AND DTC P0402. *KB UPDATED 2/27/08. *NJ
4261
TIRE SIDEWALL IRREGULARITIES. *KB UPDATED 1/30/08. *NJ
4303
4 WHEEL DRIVE INOPERATIVE FRONT AXLE WILL NOT ENGAGE - KEYWORDS CLUNK GRIND GROWL K2 K3 EQUIPPED WITH A 9.25 FRONT DIFFERENTIAL. *NJ UPDATED 2/27/08. *NJ
4419
SERVICE STABILITRAK MESSAGE C0196 AND/OR U2142. *NJ
4444
NO START/NO CRANK - LOSS OF HIGH SPEED GMLAN COMMUNICATION. *NJ
4529
HIGH IDLE, ELEVATED IDLE, AND PTO ALL DIFFERENT OPTIONS. *NJ
070232008
STEERING WHEEL OFF CENTER WHILE DRIVING STRAIGHT, CLUNK NOISE WHILE TURNING, EARLY FRONT TIRE WEAR (PERFORM TORQUE TO TIGHTEN ANALYSIS AND REPAIR AS NECESSARY) *NJ UPDATED 2/25/08. *NJ
070316002
TIRE PRESSURE MONITOR SYSTEM CONCERNS. *KB 2008 PASSENGER CARS AND TRUCKS (INCLUDING SATURN). UPDATED 2/26/08. *NJ
070138009
EI07264 - MANUAL HVAC PERFORMANCE, TEMPERATURE, MODE, A/C DOES NOT COOL, DTC B0228, B0413, B0423, B0433, B3779, B3782 *NJ UPDATED 2/15/08. *NJ
070417002
WHINE TYPE NOISE COMING FROM REAR OF VEHICLE (DIAGNOSE AND REPLACE REAR PROPELLER SHAFT). *NJ
070604027
EI07239 - 5.3L, LMG, LC9 DRIVEABILITY SYMPTOMS, HESITATION, MISS, LACK OF POWER, DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0171, P0172, P0174, P1174, P1175, CHECK ENGINE LIGHT, MIL, INJECTOR. *NJ UPDATED 2/19/08. *NJ
070845001
PROCEDURE FOR INSTALLATION OF AN AFTERMARKET TRAILER BRAKE CONTROLLER IN LIEU OF FACTORY INSTALLED INTEGRATED TRAILER BRAKE CONTROLLER. *KB UPDATED 11/02/07. *NJ UPDATED 2/19/08. *NJ
060603013
INTERMITTENT LOW BATTERY VOLTAGE, ENGINE WILL NOT CRANK, ENGINE CRANKS BUT WILL NOT START, CHARGING SYSTEM LIGHT ON, SERVICE BATTERY CHARGING SYSTEM MESSAGE DISPLAYED, DTC B1405 AND/OR B1516 SET. (REPROGRAM BCM). *KB UPDATED 11/02/07 *NJ
060842009
USE OF AUXILIARY CENTER HIGH MOUNTED STOP LAMP (CHMSL) WITH INSTALLATION OF ACCESSORIES OVERHEAD RACK SYSTEM. *NJ
060845008
INFORMATION ON AUXILIARY POWER WIRE AT TRAILER AND INSTALLATION OF AFTERMARKET TRAILER BRAKE CONTROLLER - TOWING, TOW *KB UPDATED 11/02/07. *NJ
070842013
TURN SIGNAL IN CAMPER STYLE OUTSIDE REARVIEW MIRROR (RPO DPN) DOES NOT ILLUMINATE TURN SIGNAL FLASH (REPLACE UPPER MIRROR GLASS) *NJ
070849018
VARIOUS ELECTRICAL CONCERNS - INTERMITTENTLY FUNCTIONING OR INOPERATIVE COMPONENT, IP WARNING LIGHT ON, DIC MESSAGE DISPLAYED, DTC SET, NO CRANK/START (REPAIR IP WIRING HARNESS) *NJ
040232001
RELEASE OF STEERING GEAR STUB SHAFT BEARING KIT FOR SERVICE. *TT UPDATED 08-15-07. *KB UPDATED 10/09/07. *NJ
070603005
REPLACEMENT INFORMATION FOR BROKEN T-BOLT ON NEGATIVE AND/OR POSITIVE BATTERY CABLE TERMINAL. *NJ
030309002
REAR LEAF SPRING SLAP OR CLUNK NOISE (REPLACE SPRING INSERTS) *TT UPDATED 10/18/07. *NJ
060604010
INFORMATION ON 3.5L, 3.9L, AND 5.3L E85 FUEL COMPATIBLE VEHICLES, WITH ALCOHOL CONTENT, SWITCHING BETWEEN GASOLINE AND E85 FUEL. *KB UPDATED ON 09/19/07. *NJ
070940001
FRONT SEATBELT LATCH PLATE REVERSED, FRONT SEATBELT TWISTED (PERFORM REPAIR TO UNTWIST SEATBELT). *NJ
040525002
ABS LIGHT ON, DTC'S C0265, C0201, U1041 SET AND/OR LOSS OF COMMUNICATION WITH BRAKE MODULE. (REGROUND EBCM GROUND). *KB
06162
SERVICE UPDATE FOR INVENTORY AND CUSTOMER VEHICLES E85 VIRTUAL FLEX FUEL SENSOR (VFFS) UPDATE- REPROGRAM ECM. *KB
070863005
HOOD FLUTTER, SHAKE OR VIBRATION AT HIGHWAY SPEEDS. (APPLY FLEXIBLE ADHESIVE SEALER BETWEEN INNER AND OUTER PANELS). *KB
070604013
CHUGGLE, SURGE OR HESITATION MAY BE FELT WITH ACTIVE FUEL MANAGEMENT SYSTEM CYLINDER DEACTIVATION TRANSITION FROM V8 MODE TO V4 MODE. *KB
0708110002
DOOR TRIM GAP AT REAROF DOOR. *KB
0708111003
INSTALLATION INSTRUCTIONS FOR E85 FLEX FUEL EMBLEMS AND YELLOW COLORED FUEL CAPS IN SUPPORT OF THE E85 ETHANOL MARKETING PROGRAM. *KB
07093
SERVICE UPDATE FOR INVENTORY AND CUSTOMER VEHICLES. INCORRECT GVWR AND CAPACITY INFORMATION. *KB
060139002
FRONT BLOWER MOTOR INOPERATIVE OR MAY NOT SHUT OFF IN EXTREMELY LOW AMBIENT TEMPERATURE CONDITIONS. *KB
060604066
LBZ, LLY, ENGINE WITH ROUGH IDLE, POOR PERFORMANCE, BLACK/WHITE EXHAUST SMOKE, MIL/SES LIGHT ON AND ONE OR MORE OF THE FOLLOWING DTC'S P003A, P060B, P0230, P0403, P0401, P0606, P2146, P2149, P2152, P2155. (REPROGRAM ECM AND REPLACE EGR MOTOR OR EGR VALVE. *KB UPDATED 04-27-07. *KB UPDATED. *PE
000235003
CLUNKING NOISE UNDER HOOD AND CAN BE FELT IN STEERING WHEEL. *EH UPDATED *EH UPDATED. *KB
070842003
TURN SIGNALS HAVE INCREASED FLASH RATE (REPROGRAM BCM). *KB
070848001
FRONT WINDSHIELD GLASS OPTICAL DISTORTION OR STRESS CRACKS. *KB
070941002
AIR BAG LIGHT ON, DTC B0081, SET (CLEAR DTC USING SPECIFIC PROCEDURE). *KB
010310010
INSPECTION OF TIRE AND WHEEL SIZE PRIOR TO DIAGNOSIS OF TRANSMISSION SHIFTS, POOR PERFORMANCE, SPEEDOMETER, CRUISE CONTROL CONCERNS. *KB
060603011
HUMMING OR BUZZING FROM REAR OF VEHICLE AND/OR POSSIBLE DEAD BATTERY. (CHECK FUEL PUMP RELAY AND REPLACE, IF NECESSARY). *KB
040604001
VARIOUS INTERMITTENT DRIVEABILITY CONDITIONS - HESITATION, LACK OF POWER, ETC. *TT
060316003
INFORMATION ON RECOGNIZING TIRE PRESSURE MONITORING (TPM). AVOID DAMAGE TO THE TPM SENSOR DURING TIRE/WHEEL SERVICE. *KB
060417002
REAR DRIVE AXLE WHINE NOISE (REPLACE SLIP YOKE ASSEMBLY). *KB
050138012
EI05082 - LOSS OF BLOWER MOTOR SPEEDS EXCEPT FOR HIGH SPEED OR INOPERATIVE. *TT UPDATED. *KB UPDATED *KB
060525004
INFORMATION ON REPROGRAMMING EBCM IF TECH 2 DATA FOR REAR WHEEL SPEED SENSORS IS REVERSED. *KB
060845009
REAR DOOR LOCKS/REAR WINDOWS/COURTESY LAMPS/REAR SPEAKERS INOPERATIVE, BLOWN FUSE, SIR DTC CODES. *KB
060845010
IGNITION SWITCH DIAGNOSTIC TIPS - DTC CODES C0561, P1629, P1682, U0101, U0121, U0155 AND/OR NO CRANK/NO START, HVAC, RADIO, ON STAR, POWER ADJUSTABLE PEDALS, AND OTHER ELECTRICAL COMPONENTS INOPERATIVE. *KB
4016
DELAYED OR EXTENDED CRANKING DTC P1682. *KB
3910
ALLISON TRANSMISSION EQUIPPED VEHICLES SETTING DIAGNOSTIC TROUBLE CODE (DTC) P0877. VEHICLES EQUIPPED WITH ALLISON LCT1000 MW7 TRANSMISSION. *KB
4024
REAR BRAKE PULSATION CHECK DRUM TO AXLE CLEARANCE, WITH RPO JF3 OR JF7. *KB
4151
TORSION BAR FRONT SUSPENSION ON C1500 MODELS. *KB
3878
DIESEL FUEL SYSTEM ENGINEERING INVESTIGATION. *KB
3939
TRANSFER CASE CONTROL MODULE INVESTIGATION. *KB
3227
TAILGATE CABLE SLACK. THIS INCLUDES 1998-2006 CHEVROLET AND GMC FULL AND MID SIZE TRUCKS. *EH UPDATED. *KB
4142
NO CRANK NO START NO COMMUNICATION ON LOW SPEED GMLAM. ABS BRAKE FUEL GAUGE OIL SIR SPEEDO TACH TEMPERATURE U0140, U0151, U0168, U0170, U0172, U0184, U0199, U0200, U0214, VOLT WHEEL WIRE. *KB
030604036
INFORMATION ON SERVICING FUEL INJECTORS TO AVOID CONTAMINATION. *EH UPDATED 03-19-07. *KB
060316002
INFORMATION TO RELEARN TPM SENSORS WHEN THE DRIVERS INFORMATION CENTER (DIC) DISPLAYS DASHES FOR ALL TIRE PRESSURE. *KB
060603009
DIAGNOSTIC INFORMATION ON BATTERY DRAW NO START - BODY CONTROL MODULE, BCM POWER TIMER. *KB
3931
NO MOVEMENT WHEN THE SHIFT LEVER IS MOVED TO D4 OR D3. NORMAL OPERATION WHEN MOVED TO D2 D1 OR REVERSE. *KB UPDATED. *KB
3713
DOOR GLASS POPS OUT OF RUN CHANNEL. *KB
3340
LEFT FRONT AXLE SHAFT DIFFICULT TO REMOVE. AXLE DIFFERENTIAL LEAK SEAL SHAFT. *KB
060310011
20 INCH ACCESSORY WHEELS AVAILABLE THROUGH GM ACCESORIES. *KB
060604042
LR4, LY2, L33, LH6, LM7, L59, LC9, LMG, LY5, LS2, LQ9, LQ4, L76, LY6 THROTTLE ACTUATOR CONTROL (TAC). MODULE CODES, MIL/SES DTC'S P2108, P1516, U0107, REDUCED ENGINE POWER. *KB
060845007
NO START/LOSS OF LOW SPEED LAN, DTC'S SET. *KB
3068
OIL SEEPAGE FROM TURBO AIR CHARGE COOLER HOSES OR HOSE BLOWING OFF DURING ACCELERATION. POSSIBLE DIAGNOSTIC TROUBLE CODE P0299. *TT UPDATED 04-24-07. *KB
3075
BLOWN MBEC 1 OR LBEC 1 FUSE. *KB
3136
SLIP CONDITION IN 2ND, 3RD, OR 4TH. DAMAGED 2-4 OR 3-4 CLUTCH. *KB UPDATED 10/31/07. *NJ
3190
UNABLE TO LOCATE EMERGENCY LIGHT RELAY AND/OR BLUNT CUT WIRES. *KB
3424
ELECTRONIC TRANSFER CASE UNABLE TO COMPLETE SHIFT. *TT
3425
UNABLE TO PROGRAM TIRE SIZE IN EBCM/VSES. *KB
3562
BRIDGESTONE DUELER PRODUCT INFORMATION UPDATE. *KB
3568
SERVICE BRAKE BOOSTER MESSAGE. *KB
3569
SERVICE VME - 8.6 INCH REAR AXLE WHICH EXHIBIT A GEAR WHINE CONDITION (UNTIL DECEMBER 23, 2005). *TT
3959
UNABLE TO LOWER SPARE TIRE FROM UNDERNEATH THE VEHICLE. *NJ
3999
LOSS OF POWER WHEN DRIVING IN EXTREME WINTER WEATHER. *KB
4006
WHINE HOWL NOISE FROM THE REAR DIFFERENTIAL ON VEHICLES EQUIPPED WITH AN 8.6 REAR AXLE. *KB
4030
NEW DESIGN FRONT AXLE SIDE BEARING ADJUSTERS. *KB
4040
HARSH TCC APPLY OR TCC CYCLING. *KB
4052
2-3 UPSHIFT SLIP OR FLARE. *KB
4087
POWER STEERING PUMP LEAK/ INCORRECT MOUNTING BOLT. *KB
4133
TRANSMISSION SLIPS, WILL NOT SHIFT, SES LIGHT MAY BE ILLUMINATED. *KB
4144
ALLISON LCT1000 HARSH 3-2, 2-1 DOWNSHIFT, AND ABS MAY ACTIVATE. *KB
4168
LOW POWER, POOR PERFORMANCE, OR BUSY SHIFTING. *KB UPDATED 09-26-07. *KB
4179
DUAL STAGE PASSENGER AIR BAG USED IN SINGLE STAGE APPLICATION. *KB
4181
TURN SIGNAL FLASHES FAST. *KB
4190
ENGINEERING INFORMATION REQUEST DURING REAR RING AND PINION REPLACEMENT. *NJ
4200
PERCEIVED HESITATION OR LACK OF POWER DURING THROTTLE REAPPLY AT SLOW SPEEDS. *KB
4220
RUBBER VALVE STEM PRESSURE RELEASE LEARN METHOD. *KB
4222
INSTRUMENT PANEL CONTROLS (IPC) HARD TO READ. *KB
4223
BRIDGESTONE DURAVIS TIRE CHIP AND TEAR ISSUE. *KB
4231
SERVICE VME. SUPPLEMENT TO 00-02-35-003L. UPDATE ON NEW I-SHAFT. *KB
4292
CREAKING NOISE FROM BODY. *KB
4332
ADDING AFTERMARKET TRAILER BRAKE CONTROLLER WITH INTEGRATED TRAILER BRAKE CONTROLLER. *KB
4365
IPC BACKLIGHTING INOPERATIVE TBC 2A FUSE OPEN. *KB
4383P
PART RESTRICTION ON THE ELECTRONIC BRAKE CONTROL MODULE. *KB
4389
TRAILER HITCH INSERT - PRODUCT UPDATE. *KB
4407
AUXILIARY POWER TO 7-WAY TRAILER CONNECTOR. *KB
4422
SERVICE TIRE MONITOR MESSAGE WITH AFTERMARKET WHEELS. *KB UPDATED ON 09/20/07. *NJ
4486
ONE OF THE FOLLOWING CONCERNS WHEN PROGRAMMING THE MILEAGE OR THE HOURS INTO AN EXCHANGE INSTRUMENT PANEL CLUSTER THAT IS RECEIVED FROM AN ELECTRONIC SERVICE CENTER (ESC). *NJ
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.