PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6113
This document provides the technician with a diagnostic tip if the vehicle stalls and set diagnostic trouble code P0191 and may also set P0172. The diagnostic tip has the technician inspect the high pressure fuel pump body markings to confirm it is an original manufacture part. If it is not an original manufacture part, they should install one and evaluate the vehicle.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
PIP4964F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
13-02-32-001H
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIT5994A
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-223
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
21-NA-280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
24-NA-147
This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
18-NA-115
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
22-NA-240
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
21-NA-147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminatedâ.
19-NA-256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
PIP4964E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
17-NA-281
This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIT5994
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
PIC6070A
This Preliminary Information communicates diagnostic tips for a condition of No GPS location on Radio.
PIC5611H
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PIT5698C
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
N192266180-01
Special Coverage. On some vehicles, a link ball socket in the front wiper transmission may separate. If this were to occur, the driver would experience a sudden loss of front wiper function. Dealers are to replace the front wiper transmission kit or module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
090604026V
Information.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
070316004D
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
000090002L
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
21NA280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT4916K
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
19NA256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
21NA152
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.
21NA147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
N192287100-01
Special Coverage (Revised correction statement, service procedure and customer reimbursement). Some vehicles, equipped with a 2.4L engine and certified to the EPA Bin 4 emission standard and the California Cleaner Federal Vehicle option of Bin 4 emission standard, may exhibit catalytic converter and/or oxygen sensor performance degradation, without illumination of the malfunction indicator lamp (check engine light), as a result of excessive engine oil consumption (less than 2,000 miles [3,200 km] per quart [0.946 L] of engine oil) due to piston ring wear. This special coverage covers the condition described above for a period of 10 years or 150,000 miles (241,400 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Determine if the vehicle has, or has been repaired for, an excessive engine oil consumption condition due to piston ring wear by: 1. Performing an excessive engine oil consumption test, or 2. Examining IVH or other service records to determine if a repair has been performed to remedy excessive oil consumption due to piston ring wear. If an engine oil consumption test indicates the vehicle currently has an excessive engine oil consumption condition due to piston ring wear, or if the vehicle has been repaired for an excessive engine oil consumption condition due to piston ring wear, replace the catalytic converters and oxygen sensors. See also Special Coverage bulletins 16118, N192291100 or N192291101 ?Excessive Engine Oil Consumption? for repair of engine and other components.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
070089037Q
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
21NA108
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil.
PIP5257E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
010601011L
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
090604026S
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
N192268180 and N
Emission Recalls and Special Coverage. Population movement between bulletin numbers.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
N192268180
Emissions Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a 2.4L engine and certified to the EPA Bin 4 emission standard and the California Cleaner Federal Vehicle option of Bin 4 emission standard. The vehicle?s post-catalyst oxygen sensor may provide inaccurate information to the engine control module, which manages engine combustion air-fuel ratios. If this condition occurs, tail pipe emissions may exceed allowed limits, without providing any notification to the driver. The malfunction indicator lamp (check engine light) will not illuminate. Dealers are to replace the post-catalyst oxygen sensor.
N192268181
Emissions Recall. General Motors has decided to conduct a voluntary emissions recall involving certain vehicles equipped with a 2.4L engine and certified to the EPA Bin 4 emission standard and the California Cleaner Federal Vehicle option of Bin 4 emission standard. The performance capability of the vehicle?s catalytic converters may have degraded, such that efficiency is reduced. In addition, the oxygen sensors may provide inaccurate information to the engine control module which manages engine combustion air-fuel ratios. If these conditions occur, tail pipe emissions may exceed allowed limits, without providing any notification to the driver. The malfunction indicator lamp (check engine light) will not illuminate. Dealers are to replace both catalytic converters and both oxygen sensors.
N192287100
Special Coverage Adjustment. Some vehicles, equipped with a 2.4L engine and certified to the EPA Bin 4 emission standard and the California Cleaner Federal Vehicle option of Bin 4 emission standard, may exhibit catalytic converter and/or oxygen sensor performance degradation, without illumination of the malfunction indicator lamp (check engine light), as a result of excessive engine oil consumption (less than 2,000 miles [3,200 km] per quart [0.946 L] of engine oil) due to piston ring wear. This special coverage covers the condition described above for a period of 10 years or 150,000 miles (241,400 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Determine if the vehicle has, or has been repaired for, an excessive engine oil consumption condition due to piston ring wear by 1. Performing an excessive engine oil consumption test, or 2. Examining IVH or other service records to determine if a repair has been performed to remedy excessive oil consumption due to piston ring wear. If the vehicle has, or has been repaired for, an excessive engine oil consumption condition due to piston ring wear, replace the catalytic converters and oxygen sensors. See also Special Coverage bulletins 16118, N192291100 or N192291101 ?Excessive Engine Oil Consumption? for repair of engine and other components. Note: The special coverage terms for excessive engine oil consumption may be different than the special coverage terms for the catalytic converter and oxygen sensor degradation. The repairs will be made at no charge to the customer.
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
18NA115
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
PIT4916J
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIP5180C
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
20NA026
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP5095G
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5528F
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
PIP5528E
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
120232002B
This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
070604025M
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
090089002R
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP5257D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
PIP4783B
This Prelimary information informs the dealer of a diagnotic trouble code that may set due to a failed high pressure fuel pump. Dealers are to check fuel pressure as per current testing outlined in GM service information and replace the fuel pump if needed.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
18NA072
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
20NA029
This technical bulletin provides a Service Procedure to correct a Condition of Ticking, Tap or Rattle Noise from Engine.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
130601003J
This technical bulletin provides Correction information to find the cause of oil consumption. Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
N192291100 01
Special Coverage (Revised Warranty). Some vehicles equipped with a 2.4L engine (RPO LEA) may exhibit excessive engine oil consumption (less than 2,000 miles [3,200 km] per quart [0.946 L] of engine oil), due to piston ring wear. If this condition is present, an audible rattle or knock from the engine may be heard. The engine oil pressure telltale may illuminate on the instrument panel or the following message may appear in the Driver Information Center: "Oil Pressure Low ? Stop Engine". Dealers are to perform an oil consumption test and install new pistons and piston rings if excessive consumption is found. In addition, dealers are to repair or replace any engine components that require repair or replacement if the need for such repair or replacement was solely caused by excessive oil consumption due to piston ring wear. The repairs will be made at no charge to the Customer.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PI0592F
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP4670H
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIP5528D
This Preliminary information communicates the repair recommendations for misfire in HFV6 re-manufactured engines.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
18NA061
This technical bulletin provides a procedure on diagnosing and repair moisture/ice and possibly contamination/debris in the SAI system and how to clean it out.
19NA196
This diagnostic tip advises the tech to check if the upstream O2 sensor has been replaced with a faulty or aftermarket sensor and how to verify if the sensor is the cause of the concern.
PI0592E
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
090604026R
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
130089008B
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5257C
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5528C
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIT4916H
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIP4964D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
130601003I
This technical bulletin provides Correction information to find the cause of oil consumption. Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5331H
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
PIT5205B
This Preliminary Information communication provides information to the technician about vehicles that have a blower speed knob only goes to 8 with less than expected high blower speed air flow. Technician should not replace any parts for this concern. Dealer should advise the customer to turn the ECO button Off and On at different blower speed settings 6 through 8 and note the change in the audible sound and air flow. This is a new enhancement to improve fuel economy when the ECO button is turned on.
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIT4916G
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIC6360
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
19NA065
This technical bulletin provides a procedure to replace the Aux fuel pump if found the cause of the customers concern.
PIP5122G
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
PIP5528B
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
030729004L
This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.
PIP4670F
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
PIT5402A
This Preliminary Information communication provides information to the technician for a forward collision alert or lane departure warning inoperative with no diagnostic trouble codes stored. This concern could be caused by an aftermarket windshield. Verify there is the General Motors logo in the lower right corner of the windshield.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5331G
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5528A
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT4945H
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5302B
This Preliminary Information communication provides information to the technician about vehicles that may have turn signal indicators on the Instrument Panel Cluster do not match the audible warnings. Technician will need to test the battery using the GR8. Technician should also verify the charging system is operating correctly.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5624
This Preliminary information communicates to the dealer an issue where the vehicle's engine may stumble and/or stall at startup. The dealer is to evaluate for a faulty aftermarket or incorrect upstream oxygen sensor.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17NA066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
000310003X
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5427B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
PIP5191C
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIP5601
This Preliminary information communicates
PIT4945G
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP3423P
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP5095F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5611G
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5257B
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP4495F
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5569
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
18NA125
This informational bulletin provides information for engine oil life monitor operation calculation.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIC5611F
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
110089002C
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIP5122F
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
16NA004
This technical bulletin provides a possible location and repair to a wiring harness that may be contacting the fuel pump cover.
PIP5095E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5331F
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PIP5180B
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIP4670E
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
PIP5385D
This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes. New revision adds model year and removes the customer surveys.
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5331E
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100864002D
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
17NA348
This informational bulletin advises the new way required to tow a vehicle when using a dinghy or flat towing.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP3535C
This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
16NA075
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
130232001E
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
PIP4959G
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
17NA386
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
PIT5119F
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
17NA297
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5650C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PI1043D
This preliminary informational bulletin adds the 2017 model year to information to correct a customer concern on opening hood when hood primary latch release cable is inoperative.
PIP5528
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
16NA249
Low Audible Whine Noise has been found to be transmitting from the balance shaft drive chain.
PI1067B
This preliminary informational bulletin adds the 2017 model year to repair information for a customer concern of Malfunction Indicator Lamp (MIL) on, Reduced Power Mode on, DTC(s) set, and/or poor performance/shifts.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP4495E
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
16-NA-249
LOW AUDIBLE WHINE NOISE FROM ENGINE
PI-1043D
Information on Opening Hood When Hood Primary Latch Release Cable is Inoperative Some customers or dealer personnel may comment that the inside hood release cable is not functioning and they are unable to open the hood.
PI-1067B
Malfunction Indicator Lamp (MIL) Light On, Reduced Power Mode, DTC Set, Poor Performance/Shifts In rare cases, some customers may comment that the malfunction indicator lamp is on, poor performance and reduced power mode on. Technicians may find DTC P0641 or various others set. Not all of the effects listed may be experienced. However, the different effects and driver notifications may be caused by one of the wires in the ECM harness being chafed or cut. Due to the cause of the condition, and the positions of the wires in the harness, it is unlikely that more than one circuit will be affected by the condition. This condition may be caused by the ECM wiring harness rubbing on the ECM bracket. The harness may have chafing or damage to the wires. Contact with the edge of the bracket may result in a rub-through of the wires within that harness.
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
17NA307
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being installed in the reman engines.
17NA281
This informational bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP3535B
This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
000601012H
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC6185A
This Preliminary Information communication provides information to the technician with a diagnostic tip for navigation radios that have inaccurate entries at times when using the voice recognition to input the address. When using the Navigation command "Address" or "Destination" this Allows an address to be stated as a one-shot method. When using the Navigation command "Directed Address" this Allows an address to be stated one step at a time. Directed address option may be a better choice for entering that address.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0865D
This preliminary information bulletin provides a information and a procedure on the 2.4L ecotec engine.
PIP3423N
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP4959F
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
17-NA-211
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical connections that may set a DTC instead of just replacing a part.
PIT5119E
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIT5119E (1)
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
17-NA-237
This technical bulletin provides a procedure to replace the HVAC drain hose due to clogging causing a water leak within the vehicle.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
16-NA-004
This technical bulletin provides a procedure to locate and repair the engine wiring harness that has rubbed on the fuel pump cover creating a short and correct the customers concern of a engine no start or no p/s.
16-NA-238
This technical bulletin provides a procedure to reprogram the radio using SPS to correct the conditons of a Check DAB message or DAB re-routing message displayed after a recent reprogramming of the radio has been performed.
PIP5507B
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC5611E
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5507A
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIP5507
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5216F
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIP5191B
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
16-NA-355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
PIP5389D
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P015A set. Dealers are directed to review Technical Service Bulletin17-NA-086 for repair information.
03-06-03-004U
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
17-NA-084
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
17-NA-086
This technical bulletin provides a procedure to reprogram the ECM to correct the MIL.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
PIC6192A
This Preliminary Information communication advises the technician that Engineering Has released the Navigation Map Data update for the listed model years.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
17-NA-058
This informational bulletin provides information on Voice Recognition Release Note for v2017 Map Update.
10-00-89-006F
This informational bulletin provides information for dealers how to submit a product information report.
12-09-41-002D
This informational bulletin explains not to put anything metal or conductive on the passenger seat or it may set the reminder chime off.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
07-07-30-010D
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4990D
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5095D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
17-NA-047
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5959C
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
02-00-89-002Q
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
PIP5331D
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 model year.
01-03-10-003O
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
07-06-04-025L
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
15-00-90-002A
This informational bulletin provides information on Installing the Correct Replacement Spin-On Oil Filter When Servicing.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP4902J
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5385C
This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes.
PIP5180A
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
GCUS-3-814
44180 01 - Customer Satisfaction - Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
99-00-89-019O
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
PIT4915E
This Preliminary Information communication advises the technician that vehicles built with Regular Production Option Code (UW6) the subwoofer is only used for the Active Noise Cancellation.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
99-00-89-019N
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
01-03-10-003N
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
02-00-89-002P
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIC6233
This Preliminary Information communication provides information to the technician about vehicles that when an incoming Bluetooth call will ring through the vehicle system, but the call can only be answered by using the handset. Technician can update the radio using the latest version of 15-NA-081 if the vehicle is 2014 or newer. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
04-06-04-051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIP5122E
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
040604051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
15NA044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
16NA355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
030603004S
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
030603004T
Battery Testing and Warranty Replacement Requirements (North America ONLY)
040089015N
This warranty administration bulletin provide policy information on required operating procedures.
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PIT4916F
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIT4995F
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5389C
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P015A set. After performing all published Service Information diagnostics for the Diagnostic Trouble Code and no resolution found, technician should check the engine oil level for being overfilled.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
07-00-89-037J
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
08-08-44-029G
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5282A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
08-08-44-015G
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIP5244B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE POOR FUEL ECONOMY. DEALER SHOULD OBTAIN A DETAILED DESCRIPTION OF OUR CUSTOMERS DRIVING HABITS ON A DAILY BASIS, SUCH AS MILES DRIVEN, ROADS TAKEN, AND SPEEDS DRIVEN. TECHNICIAN SHOULD PERFORM AN INITIAL FUEL ECONOMY EVALUATION AND ACTUAL DRIVING EVALUATION.
01-00-89-010L
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
07-08-49-020K
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
01-03-10-003L
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
PI1010A
THIS PRELIMINARY INFORMATIONAL BULLETIN ADDS 2015 - 2017 MY'S TO REPAIR INFORMATION FOR A CUSTOMER CONCERN OF ROUND DARK CIRCLES OF PAINT DISCOLORATION ON CENTER REAR AREA OF ROOF.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
PIC6198A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON STEPS TO PERFORM TO DETERMINE IF THE CUSTOMER'S BATTERY DRAIN CONCERN IS BEING CAUSED BY A KNOWN CONCERN WITH BLUETOOTH CALL TRANSFER OPERATION WHEN EXITING THE VEHICLE. IF THE CONCERN IS DUPLICATED AT THE DEALER WITH THE ONSTAR LED IS STILL GREEN AFTER THE VEHICLE IS TURNED OFF AND THE BLUETOOTH CALL WAS DISCONNECTED. DEALER SHOULD ADVISES THAT ENGINEERING IS AWARE OF THE CONCERN AND IS CURRENTLY INVESTIGATING THE ISSUE.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
PI1259A
This informational bulletin explains the normal operation of the instrument panel automatic display brightness when the vehicle leaves a dark area.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
00-03-10-006M
THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT.
PIP4548F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN WHAT TO INSPECT IF CODES P0016 AND/OR P0017 ARE SETTING ON A PROPERLY TIMED ENGINE OR A CONDITION OF THE VEHICLE CRANKS BUT WILL NOT START. TECHNICIAN SHOULD INSPECT THE RESPECTIVE INTAKE OR EXHAUST CAMSHAFT RELUCTOR TO SEE IF IT HAS SPUN ON THE CAMSHAFT. THE RELUCTOR CANNOT BE REPOSITIONED SO THE CAMSHAFT MUST BE REPLACED. THE NEW CAMSHAFTS COME WITH THE RELUCTOR ALREADY PRESSED ON IN THE CORRECT POSITION.
PIC4788G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN OF DIAGNOSTIC INSTRUCTIONS TO TAKE WHEN THE KEY WILL NOT FOLD INTO THE FOB OR WILL NOT STAY IN THE FOLDED POSITION. THE TECHNICIAN MAY COMMENT THAT THE KEY IN THE FOB WILL NOT FOLD CLOSE OR STAY LATCHED CLOSED. DAMAGE TO THE FOLDING MECHANISM COULD RESULT FROM STORING THE KEY IN THE DOOR LOCK CYLINDER AND ACCIDENTLY BUMPING OR MAKING CONTACT WITH THE KEY FOB. PLEASE ADVISE ALL DEALER PERSONNEL TO REFRAIN FROM STORING THE KEY IN THE DOOR LOCK EVEN FOR BRIEF PERIODS.
PIC5428G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. THE ELECTRONIC BRAKE CONTROL MODULE MAY HAVE ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES C0035-C0050 WITH SPECIFICALLY SYMPTOM 18, 5A, OR 0F. TECHNICIAN WILL GAIN ACCESS TO THE CORRECT WHEEL BEAR PER THE DIAGNOSTIC TROUBLE CODE THAT IS SET. IF DEBRIS IS FOUND ON THE MAGNETIC ENCODER RING IT WILL NEEDED TO BE CLEANED.
PIC6185
This Preliminary Information communication provides information to the technician with a diagnostic tip for navigation radios that have inaccurate entries at times when using the voice recognition to input the address. When using the Navigation command "Address" or "Destination" this Allows an address to be stated as a one-shot method. When using the Navigation command "Directed Address" this Allows an address to be stated one step at a time. Directed address option may be a better choice for entering that address.
15-08-44-001H
THIS INFORMATIONAL BULLETIN PROVODES INFORMATION ON THE GM OF CANADA ONSTAR CELLULAR COMMUNICATION UPGRADE.
PI1521B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE POWER STEERING FUSE FOR A CONDITION OF LOSS OF POWER STEERING ASSIST AND/OR SERVICE POWER STEERING MESSAGE DISPLAYED.
PI0828C
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR APPLYING 2 WAY TAPE AND SPLASH GUARDS TO CORRECT A CONDITION OF DUST INTRUSION INTO THE PASSENGER COMPARTMENT.
PI1358B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO INSTALL RETAINERS TO THE CARPET TO CORRECT A CONDITION OF THE CARPET PULLING LOOSE FROM UNDER DRIVER SIDE BODY HINGE PILLAR TRIM PANEL .
PI1090B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR APPLYING SEAM SEALER TO THE OUTER FLOOR PANELS TO CORRECT A CONCERN REGARDING A WET FLOOR OR CARPET.
PI1507A
THIS PRELIMINARY INFORMATION BULLETIN INFORMS TECHNICIANS THAT SOME VEHICLES ROOFS ARE WAVEY AND THAT ITS PART OF THE BUILD PROCESS AND SHOULD BE CONSIDERED NORMAL.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
10-08-110-001E
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.
PIP5277B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE A RESONANCE TYPE VIBRATION OCCURS BETWEEN 40 TO 60 MPH. IN MOST CASES THE ENGINE MUST BE UNDER A SLIGHT LOAD SUCH AS A/C COMPRESSOR ENGAGEMENT, LIGHT THROTTLE, AND IN 6TH GEAR TORQUE CONVERTER CLUTCH APPLIED. TECHNICIAN WILL RELAX THE ENGINE AND TRANSMISSION MOUNTS, THEN THE EXHAUST SYSTEM BY LOOSENING THE FRONT PIPE STUDS. ALSO WORK DOWN THE SYSTEM DISCONNECTING ONE EXHAUST HANGER AT A TIME. THEN TAKE THE VEHICLE ON A TEST DRIVE TO VERIFY THERE WAS IMPROVEMENT. IF ADDITIONAL STEPS ARE REQUIRED PLACE TWO SETS OF EXHAUST DAMPENERS ONE SET BEFORE AND ONE SET AFTER THE FRONT CATALYTIC CONVERTER. IT MAY BE REQUIRED TO MOVE THE PAIR OF DAMPENERS ALONG THE EXHAUST SYSTEM TO GET THE BEST RESULTS.
15-08-51-001C
THIS INFORMATIONAL BULLETIN UPDATES THE PART INFORMATION OF A INSULATOR SERVICE PART FOR PREVENTION OF LIFTGATE RUST/CORROSION AT CENTER APPLIQUE.
09-06-04-026M
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIP-5389-B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN REGARDING VEHICLES EQUIPPED WITH ENGINE REGULAR PRODUCTION OPTION CODE LEA, LCV, AND LKW MAY HAVE A SERVICE ENGINE SOON LAMP WITH DIAGNOSTIC TROUBLE CODE P015A SET. IF THE SERVICE INFORMATION FOR DIAGNOSTIC INSTRUCTION FOR DIAGNOSTIC TROUBLE CODE P015A WAS COMPLETED INSPECT THE ENGINE OIL LEVEL FOR BEING OVERFILLED. IF THE ENGINE OIL LEVEL IS FOUND TO BE OVERFILLED, READJUST TO CORRECT LEVEL AND RE-EVALUATE THE CONCERN. IF THE STEPS DO NOT LEAD TO A RESOLUTION, ADVISE THE CUSTOMER THAT ENGINEERING IS AWARE OF THIS CONCERN AND IS WORKING ON A REPAIR.
99-08-51-007G
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
PIP-5389-A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN REGARDING VEHICLES EQUIPPED WITH ENGINE REGULAR PRODUCTION OPTION CODE LEA, LCV, AND LKW MAY HAVE A SERVICE ENGINE SOON LAMP WITH DIAGNOSTIC TROUBLE CODE P015A SET. IF THE SERVICE INFORMATION FOR DIAGNOSTIC INSTRUCTION FOR DIAGNOSTIC TROUBLE CODE P015A WAS COMPLETED INSPECT THE ENGINE OIL LEVEL FOR BEING OVERFILLED. IF THE ENGINE OIL LEVEL IS FOUND TO BE OVERFILLED, READJUST TO CORRECT LEVEL AND RE-EVALUATE THE CONCERN. IF THE STEPS DO NOT LEAD TO A RESOLUTION, ADVISE THE CUSTOMER THAT ENGINEERING IS AWARE OF THIS CONCERN AND IS WORKING ON A REPAIR.
PI0592D
This informational bulletin provides information on service programming system (SPS) errors.
PIP-5122-D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIANS FOR DIAGNOSING AND REPAIRING VEHICLES THAT HAVE AN ISSUE WITH A POP NOISE FROM THE FUEL TANK AREA AFTER A COLD START OR EVAPORATIVE EMISSIONS SYSTEM PURGE. TECHNICIAN WILL BE ABLE TO USE GLOBAL DIAGNOSTIC SYSTEM 2 TO DUPLICATE THE CONCERN BY COMMANDING A PURGE AND SEAL ON THE EVAPORATIVE EMISSIONS SYSTEM. REPLACEMENT OF THE AUXILIARY FUEL PUMP MODULE ASSEMBLY WILL CORRECT THIS CONCERN.
10-00-89-005F
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
12-08-132-001D
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.
PIP-3140-G
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT A NOISE OR A VIBRATION IN THE VEHICLE THAT SEEMS TO BE ABNORMAL MAY NOT HAVE BEEN THERE WHEN THE VEHICLE WAS PURCHASED. TECHNICIAN SHOULD LOOK FOR NON - GENERAL MOTORS AFTERMARKET ACCESSORIES INSTALLED ON THE VEHICLE THAT CAN CAUSE THESE ISSUES.
16-NA-144
This technical bulletin provides a procedure to replace the wiper transmission and wiper motor to correct a customer concern that the windshield wipers are inoperative caused by to the wiper transmission linkage separating as a result of corrosion at the ball socket joints.
16-NA-146
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT ALL FOUR OF THE LIFT GATE MOUNTING BRACKETS AND REPLACE BRACKETS IF NECESSARY TO CORRECT A CUSTOMER CONCERN THAT AFTER OPENING THE POWER LIFT GATE, IT WILL NOT STAY IN THE FULL OPEN POSITION AND MAY DRIFT DOWN A FEW INCHES BEFORE COMING TO A REST CAUSED BY TO AN INCORRECT BALL STUD STRUT BRACKET BEING INSTALLED DURING ASSEMBLY.
PI1223B
This informational bulletin provides information on black smoke and rough idle on cold start.
15-08-51-001B
THIS INFORMATIONAL BULLETIN ANNOUCES THE AVAILABILITY OF A INSULATOR SERVICE PART FOR PREVENTION OF LIFTGATE RUST/CORROSION AT CENTER APPLIQUE.
SB-02-07-30-029Z
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
SB-16NA-131
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC-6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6193A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS. THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.
PIP5168E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
SB-10-08-46-001C
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIP-5331-C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR A POSSIBLE RATTLE, TICK, OR KNOCK TYPE NOISE COMING FROM THE ENGINE.
PIP5331C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR A POSSIBLE RATTLE, TICK, OR KNOCK TYPE NOISE COMING FROM THE ENGINE.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
SB-16-NA-119
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
PIP-5385-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSING THE CONCERN. THE VEHICLE MAY HAVE A SERVICE ENGINE SOON LIGHT ON OR REDUCED ENGINE POWER MESSAGE ON THE DIVER INFORMATION CENTER.
PIP-5389
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSING THE CONCERN WITH DIAGNOSTIC TROUBLE CODE P015A . THE VEHICLE MAY HAVE A SERVICE ENGINE SOON LIGHT ON THE CLUSTER.
PIP5385A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSING THE CONCERN. THE VEHICLE MAY HAVE A SERVICE ENGINE SOON LIGHT ON OR REDUCED ENGINE POWER MESSAGE ON THE DIVER INFORMATION CENTER.
PIP5389
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSING THE CONCERN WITH DIAGNOSTIC TROUBLE CODE P015A . THE VEHICLE MAY HAVE A SERVICE ENGINE SOON LIGHT ON THE CLUSTER.
PI-0814-E
THIS PRELIMINARY INFORMATION BULLETIN PROVIDES A PROCEDURE TO REPLACE CERTAIN COMPONENTS TO CORRECT A CUSTOMER CONCERN OF A STEERING VIBRATION, FELT THROUGH THE STEERING WHEEL AND VEHICLE STRUCTURE, COMBINED WITH A MOAN TYPE NOISE DUE TO ENGINE FIRING PULSATIONS BEING TRANSMITTED INTO THE STEERING SYSTEM.
PIC-6192
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ENGINEERING IS WORKING ON THE MAP UPDATE AND HAS A TENTATIVE RELEASE DATE AROUND THE 4TH QUARTER OF 2016 TO THE 1ST QUARTER OF 2017.
PIC6192
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ENGINEERING IS WORKING ON THE MAP UPDATE AND HAS A TENTATIVE RELEASE DATE AROUND THE 4TH QUARTER OF 2016 TO THE 1ST QUARTER OF 2017.
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-16-NA-117
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
PI-0281-E
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
SB-15-08-51-001A
THIS INFORMATIONAL BULLETIN ANNOUCES THE AVAILABILITY OF A INSULATOR SERVICE PART FOR PREVENTION OF LIFTGATE RUST/CORROSION AT CENTER APPLIQUE.
SB-16-NA-109
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.
PIP5331B
This Preliminary Information communication provides information to the technician that some vehicles may have rattle, tick, or knock type noise. If there are any drivability concerns they should be addressed prior to the following diagnostic progression. Technician will take a sound file or video with sound of the noise prior to dis-assembly. Technician may find this noise hard to isolate to one area in the engine. There are four different steps to take to diagnosis the concern. Technician will perform injector diagnosis to ensure there are no leaking injectors causing a noise due to excessive fuel in any one cylinder. Replace any out of specification injectors the reevaluate for the noise. Technician will remove the intake manifold and visually inspect for excessive carbon on the intake valve stems and top of the valve causing noise. If carbon is present then follow the latest version of PIP5029 to clean the valves or replace heads as needed. Technician will remove the cam cover of the affected bank (both if needed) to inspect for soft or spongy stationary hydraulic lash adjusters. Push down on the rocker end at the stationary hydraulic lash adjusters to test for soft or spongy. If soft or spongy stationary hydraulic lash adjusters are found, carefully remove the affected head and inspect the oil passage below the head gasket for debris. If debris is found, inspect the camshaft caps for wear or discoloration due to lack of oil. During inspection if wear or discoloration is found then replace the cylinder head assembly with camshafts. If there is no wear or discoloration, clean the oil passages and replace the head gasket. Technician will use chassis ears or a stethoscope; listen to the right and left side of the engine. Once the noise is isolated or if unable to isolate, remove the piston and rod assemblies from the affected bank(s) to inspect for either; a loose rod bushing in the rod, or a loose wrist pin in the bushing. If this is found, replacing the piston an
PIT5236G
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
00-03-10-002J
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.
PI0572C
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar®), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.
PI0360F
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications
PIP5385
This Preliminary Information communication provides information to the technician with the steps to diagnose and repair vehicles that may have Service Engine Soon lamp or reduced engine power message came on and was cleared after cycling the key. Also technician may find a P228C set as current or history, and a prior history of High Pressure Fuel Pump replacement, and the customer has been using E85 fuel. If the Diagnostic Trouble Code is current follow Service Information instruction for the repair. If the code is set in history and there are no current drivability concerns take a large fuel sample and let it sit for a couple of hours looking for contamination. Verify the fuel pressure using a scan tool the actual and desired fuel pressures are very close to the same. If contamination is found in the tank then completely flush the fuel system and add e-10 fuel. Also remove the high pressure fuel pump inlet line from both ends. Using regulated air down to about 60 pounds per square inch or lower, blow through the inlet side of this pipe / hose. Inspect for restriction in the check valve built into this hose. If restricted then replace the pipe run a tank of premium fuel through the vehicle and reevaluate the concern.
PIC6120A
This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system.
08-00-89-014B
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics
07-00-89-037I
This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs
16-NA-075
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds
PIC6181
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIC6116A
This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded.
PIP5232C
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
16-NA-069
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
03-00-89-006M
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores
03-06-03-004O
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)
06-00-89-029M
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
09-00-89-002M
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
04-00-89-015K
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.
PIT3046G
This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
16-NA-055
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
PIC6158B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN SOME VEHICLES WITH RADIO REGULAR PRODUCTION OPTION CODE UFU, UP9, OR UHQ MAY HAVE SOME BLUETOOTH ISSUES, RADIO FREEZING UP, XM GRAPHICS ISSUES OR RADIO REBOOT. TECHNICIAN WILL UPDATE THE RADIO USING TIS2WEB.
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
04-06-01-029H
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)
12-09-41-002C
This informational bulletin provides information on Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On or Set DTC B101D When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
PIP4990C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON THAT COMES ON. TECHNICIAN MAY FIND A DIAGNOSTIC TROUBLE CODE U0101 CURRENT OR STORED HISTORY. TECHNICIAN SO CHECK TERMINAL PIN FIT AT TRANSMISSION CONNECTOR, UNDER HOOD FUSE BLOCK. ALSO THE TRANSMISSION CONTROL MODULE GROUND WILL NEED TO BE INSPECTED. TECHNICIAN WILL REVIEW THE APPROPRIATE SERVICE INFORMATION DIAGNOSTICS FOR DTC U0101.
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
08-08-44-015F
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)
13-06-01-003H
This technical bulletin provides a procedure to replace the pistons, connecting rods and bearings for vehicles that have the condition of excessive oil consumption
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
02-08-98-002F
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange
PI0716B
This preliminary informational bulletin provides a procedure to install GM accessory mud guards for vehicles with the condition of road debris on rocker panel at floor door area
16-NA-012
This technical bulletin provides a procedure to Inspect harness, splice 6 wire pigtail connector. Replace Accelerator Pedal Position (APP) sensor on vehices that have the condition of Malfunction Indicator Light (MIL) ON, Reduced Power Mode and DTCs
PIP5264
This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires.
16-NA-025
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
06-08-50-009I
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIP5093B
Some customers may complain of an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures (Generally 0 F /-17 C or Colder). They may also comment that they heard a single "pop" noise right before the oil leak started. Upon inspection, the technician will find that the oil leak is coming from the rear main oil seal of the engine as shown below. This may be the result of a frozen PCV system and excessive crankcase pressure. If a leaking rear main oil seal is found in warmer climates, this PI does not apply.
PIP5257
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
13-02-32-001D
This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.
16-NA-011
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends
06-06-01-010C
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
PI1358A
This preliminary informational bulletin provides a procedure to install retainers to the carpet to correct a condition of the carpet pulling loose from under driver side body hinge pillar trim panel
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
05-08-51-001H
This informational bulletin provides information on removing paint stains on the under side of protective shipping film
130232001D
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
16NA011
Infotainment System Will Not Return to Media After Bluetooth Call Ends
SB-0000193017-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5257A
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIC6158
This Preliminary Information communication provides information to the technician some vehicles with radio Regular Production Option Code UFU, UP9, or UHQ may have some Bluetooth issues, radio freezing up, XM graphics issues or radio reboot. Technician will update the radio using TIS2Web.
15747
15747 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2013 MODEL YEAR BUICK ENCORE, LACROSSE, REGAL, VERANO, CHEVROLET CAMARO, CRUZE, EQUINOX, MALIBU, VOLT, GMC TERRAIN MODEL VEHICLES EQUIPPED WITH PANASONIC COLOR NAVIGATION AND COLOR CONNECTED RADIOS (RPO UHQ OR UFU & UP9), MAY HAVE A CONDITION THAT COULD AFFECT TRAVEL LINK (WEATHER, MOVIES AND FUEL INFORMATION) SELECTIONS INCLUDED WITH CURRENT PAID SIRIUSXM SATELLITE RADIO SUBSCRIPTION SERVICE. DEALERS ARE TO PERFORM A SOFTWARE UPDATE TO THE RADIO.
PIT5353A
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT4943D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIP4548E
This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Technician should inspect the respective intake or exhaust camshaft reluctor to see if it has spun on the camshaft. The reluctor cannot be repositioned so the camshaft must be replaced. The new camshafts come with the reluctor already pressed on in the correct position.
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
OnStar Voice Fallback Number Update
PIP5216D
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
15-NA-069
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.
PI1043C
This preliminary informational bulletin adds the 2016 model year to information to correct a customer concern on opening hood when hood primary latch release cable is inoperative.
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
00-03-10-006L
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
PIT5214B
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIC3100E
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIP5216C
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
15-08-44-001F
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIP5277A
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have a resonance type vibration occurs between 40 to 60 MPH. In most cases the engine must be under a slight load such as Air Conditioning compressor engagement, light throttle, and in 6th gear Torque Converter Clutch applied. Technician will relax the engine and transmission mounts, then the exhaust system by loosening the front pipe studs. Also work down the system disconnecting one exhaust hanger at a time. Then take the vehicle on a test drive to verify there was improvement. If additional steps are required place two sets of exhaust dampeners one set before and one set after the front catalytic converter. It may be required to move the pair of dampeners along the exhaust system to get the best results.
10-00-89-005E
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
PIP5216B
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIT5302A
This Preliminary Information communication provides information to the technician about vehicles that may have turn signal indicators on the Instrument Panel Cluster do not match the audible warnings. Technician will need to test the battery using the GR8. Technician should also verify the charging system is operating correctly.
02-07-30-029Y
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
15-NA-044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
01-06-01-011I
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
08-08-44-029F
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI0799A
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
PIP3423M
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP4919E
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIC5953B
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
15-NA-030
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
06-00-89-031C
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
15-06-03-001A
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PIP5095C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
08-08-44-029E
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI1521A
This preliminary informational bulletin provides repair information to correct a customer concern of loss of power steering assist, hard to steer, and/or "Service Power Steering" message on in DIC.
PIP5331
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles with a rattle, tick, or knock type noise. Technician will use chassis ears to listen to the right and left side of the engine and isolate which bank the noise is from. Technician should now remove the piston and rod assemblies from the affected bank to inspect for a loose rod bushing in the rod, or a loose wrist pin in the bushing. There should be no metal through the oil and a piston and rod assembly will repair this noise. If technician finds metal refer to the latest version of PIP5216. If no wrist pins or bushings are found loose and all other diagnostics for this type of noise has been exhausted then engine replacement may be necessary.
05-03-07-009H
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
PIP3423L
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP5191A
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIT5119D
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIT5468
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
PIT4994E
This Preliminary Information communication provides information to the technician about vehicle that have a rattle noise from the rear lift gate on rough roads. Technician will need to inspect the lift gate wedges by opening the lift gate, insert paper between the body side & lift-gate side wedges, and then close the lift gate. If the paper cannot be removed, grease lift-gate side wedges. If the paper can be removed, reset the wedges by loosen lift-gate side wedge center screw to allow center portion to "ratchet" along internal detents freely, pull center adjustment portion of lift-gate side wedges to full downward position, close lift-gate to full latch engagement then use power to close lift-gate system (if available), close manually on non-power lift gates and do not slam, open lift gate, and pull the center adjustment portion down one additional detent & torque screw 5.0 newton meters if wedge adjustment does not have enough travel for the one additional detent add washer under the two lift-gate side wedge attachments to shim as required. Now to inspect the lift gate wedges by opening the lift gate, insert paper between the body side & lift-gate side wedges, and then close the lift gate. If the paper cannot be removed, grease lift-gate side wedges. If the concern is still present adjust lift-gate latch striker.
PIT5464
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5465
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIT5427A
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
PI-1090-A
CHEVROLET/GMC: IN FOOTWELL AREA OF SOME VEHICLES, IN DRIVER OR PASSENGER SIDE, CARPET/FLOOR IS WET DUE TO SEALING THAT WAS INSUFFICIENT OR INCOMPLETE IN FRONT ROOF OF BODY SIDE SEAMS OUTER PANEL. MODEL 2010-16 TERRAIN, EQUINOX. *PE
PI1090A
This preliminary informational bulletin adds the 2015 and 2016 Model Years to repair information to correct a customer concern of finding a wet carpet/floor in the driver or passenger footwell area.
PIT4916E
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIT4995E
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
PIT5205A
This Preliminary Information communication provides information to the technician about vehicles that have a blower speed knob only goes to 8 with less than expected high blower speed air flow. Technician should not replace any parts for this concern. Dealer should advise the customer to turn the ECO button Off and On at different blower speed settings 6 through 8 and note the change in the audible sound and air flow. This is a new enhancement to improve fuel economy when the ECO button is turned on.
15-00-89-005
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
15-08-51-001
This informational bulletin announces the availability of a insulator service part for prevention of liftgate rust/corrosion at rear center applique
PIC6120
This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system.
PI1521
This preliminary informational bulletin provides repair information to correct a customer concern of loss of power steering assist, hard to steer, and/or "Service Power Steering" message on in DIC.
PIC6116
This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded.
10-08-110-001D
This informational bulletin provides information on the proper use of GM floor mats.
00-06-01-026G
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
07-00-89-037H
This warranty administration bulletin provides policy information on courtesy transportation and roadside assistance programs.
09-09-40-001C
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIT5236F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIT5435
This Preliminary Information communication provides information to the technician about vehicles that have a creak, pop, tick or itch type noise from the center of the dash or base of the windshield area while driving the vehicle. Technician will need to gain access to the center bracket under the cowl. Technician will need to apply 3M? Urethane Sealer part number 08609, between the bracket and bulkhead and around the bracket itself.
PI-1521
BUICK/CADILLAC/CHEVROLET/GMC: DUE TO AN IMPROPER JUMP START, THE POWER STEERING FUSE WAS EITHER BLOWN OR FAILED, CAUSING A HARD STEERING. OR LOSS OF POWER STEERING ASSIST. MODEL 2013-16 LACROSSE, REGAL, MALIBU, 2010-13 EQUINOX, TERRAIN, 2014-15 ELR, 2014-16 IMPALA, 2012-15 VERANO, 2011-15 CRUZE, VOLT. *PE
09-00-89-002L
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
PIC5932A
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIT5236E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
99-01-39-004G
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
03-06-03-003E
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
PIC4788F
This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods.
03-07-29-004J
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
PIT5443
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
03-00-89-006L
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
01-08-51-003E
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
05-06-04-022M
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
06-00-89-029K
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
PIC5491G
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT5442
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PIP5301A
This Preliminary Information communication provides information to the technician the steps on how to diagnose and repair vehicle that may have Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P219A. Technician should use published Service Information diagnostics for Diagnostic Trouble Code P219A. If the Global Diagnostic System 2 fuel injector balance test does not isolate a cause for this concern, perform the Fuel Injector Diagnosis (w/CH47976 and CH-47976-500) in Service Information and evaluate for a rich or lean fuel injector.
03-06-03-004N
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
PIC5650B
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PI0233E
This preliminary informational bulletin adds the 2015-2016 model years to repair information to correct a customer concern of inaccurate or slow response of outside air temperature display.
PIT5424
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have intermittent hard start Service Engine Soon Malfunction Indicator Lamp or low oil pressure lamp on. Technician may find Diagnostic Trouble Codes P0261, P0264, P0267, P0270, P0273, P0276, and or P0641. Technician should inspect the engine harness routing the Engine Control Module and the upper rear of the engine. Technician should repair and wires that are damaged from the harness rubbing. After the wires are repaired protective wrap, and reposition the harness away from the engine.
07-06-04-019E
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
15-06-03-002
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
PI1492
This preliminary informational bulletin provides repair information on Electronic Brake Control Module (EBCM) reprogramming to correct a customer concern that during the activation of the Forward Collision Alert System (FCA), the car feels as if it is prematurely decelerating.
02-00-89-002O
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).
PIC6107
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
PIT5214A
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
99-00-89-019M
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
15-08-44-001C
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PI1120C
This preliminary informational bulletin provides a windshield molding lubrication repair to correct a customer concern of a creak or pop type noise coming from the windshield area during cold ambient temperatures.
PIP5301
This Preliminary Information communication provides information to the technician the steps on how to diagnose and repair vehicle that may have Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P219A. Technician should use published Service Information diagnostics for Diagnostic Trouble Code P219A. If the Global Diagnostic System 2 fuel injector balance test does not isolate a cause for this concern, perform the Fuel Injector Diagnosis (w/CH47976 and CH-47976-500) in Service Information and evaluate for a rich or lean fuel injector.
PIP5216A
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIT5384A
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
PI1067A
This preliminary informational bulletin adds the 2016 model year to repair information for a customer concern of Malfunction Indicator Lamp (MIL) on, Reduced Power Mode on, DTC(s) set, and/or poor performance/shifts.
14232A
14232A - SPECIAL COVERAGE (WARRANTY TRANSACTION INFORMATION REVISED). SOME 2012-2014 MODEL YEAR (MY) BUICK VERANO, 2011-2014 MY CHEVROLET CRUZE AND VOLT, 2010-2014 MY CHEVROLET EQUINOX AND GMC TERRAIN, AND 2013-2014 MY CHEVROLET MALIBU VEHICLES, EQUIPPED WITH ELECTRONIC POWER STEERING (NJ0/NJ1), MAY HAVE INCREASED FRICTION IN THE STEERING SYSTEM. THIS COULD CAUSE THE STEERING WHEEL TO STICK IN THE STRAIGHT-AHEAD POSITION AFTER DRIVING LONG DISTANCES ON A STRAIGHT HIGHWAY. THE STEERING WHEEL CAN BE TURNED BUT IT MAY REQUIRE INCREASED EFFORT. DEALERS ARE TO 1) REPLACE THE STEERING GEAR ON 2010-2012 MODEL YEAR VEHICLES; OR 2) REPROGRAM THE POWER STEERING CONTROL MODULE ON 2013-2014 MODEL YEAR VEHICLES.
PIT5236D
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
09-00-89-002K
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
PIC5611D
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5297
This Preliminary Information communication provides information to the technician about vehicles that may have difficulty filling the fuel tank and / or experience fuel spit-back when fueling. Technician will follow published Service Information diagnostics to determine a root cause. If Service Information diagnostics does not isolate the cause of this concern, dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5427
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
SC-14232
GEMS/CHEVROLET/BUICK: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON SOME VEHICLES, THE STEERING WHEEL WOULD STICK IN STRAIGHT AHEAD POSITION AFTER LONG DISTANCE DRIVING ON STRAIGHT HIGHWAY DUE TO STEERING SYSTEM HAVING AN INCREASED FRICTION AND TURNING WOULD BE AN INCREASED EFFORT. MODEL 2011-2014 CRUZE, VOLT, 2010-14 EQUINOX, TERRAIN, 2012-14 VERANO, 2013-14 MALIBU. *PE UPDATED 11/6/15. *PE
PIC5322D
This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message.
PIT3117J
This Preliminary Information communication provides information to the technician of part numbers that are missing from the service information documents. The following part numbers are for a cam nut that is available to adjust the rear toe 11519455, 11562237, 11570574.
PIT5422
This Preliminary Information communication provides information to the technician for vehicles with an intermittent malfunction indicator lamp on, the interior lamps are inoperative and or the lift gate is inoperative. Diagnostic trouble codes U0078, U0140, U0151, U0155, U0164, U0198, or U0230 can be present. Inspect the body harness connector X901 for water intrusion or corrosion. Repair the connector and terminals as required.
05-06-04-035E
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-00-89-004A
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
00-06-01-026F
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
10-08-42-001E
This technical bulletin provides repair information for low beam headlamp bulb diagnosis/replacement to correct a customer concern that the low beam headlamp is inoperative.
15-08-44-001A
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIP4959E
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5209C
This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
PIT5076E
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIC6092
This Preliminary Information communication advises the technician to not replace any parts for the XM weather, fuel, or movies tabs not working or no information coming up on the display. Apologize to the customer for the inconvenience and let them know that General Motors is working on a solution for this concern.
PIT5402
This Preliminary Information communication provides information to the technician for a forward collision alert or lane departure warning inoperative with no diagnostic trouble codes stored. This concern could be caused by an aftermarket windshield. Verify there is the General Motors logo in the lower right corner of the windshield.
PIT-5171
GMC/CHEVROLET: A COMMUNICATION FAULT, REGARDING SERVICE STABILITY TRACTION AND ABS REAR WHEEL SPEED DTC OR CHASSIS EXPANSION BUS, WHICH IS RELATED TO AN INTERNAL WIRE BREAK INSIDE WIRE HARNESS INSULATION TO X411 CONNECTOR. MODELS 2010-2012 CHEVROLET EQUINOX & GMC TERRAIN. *PE UPDATED ON 5/9/2013. *KB UPDATED 7/10/2013. *KB UPDATED 2/1/16. *PE
PIT-5402
CHEVROLET/GMC: DUE TO POSSIBLE AFTERMARKET WINDSHIELD, SOME VEHICLES MAY BE EXPERIENCING AN INTERMITTENT WARNING PERTAINING TO AN INOPERATIVE LAND DEPARTURE WARNING AND/OR FORWARD COLLISION ALERT. MODEL 2013-15 EQUINOX, TERRAIN. *PE
PIT5400
This Preliminary Information communication provides information to the technician for vehicles with a malfunction indicator lamp on, service stabilitrak, power steering or vehicle soon message displayed on the drivers information center. The technician may find the following diagnostic trouble codes U0073, U0100, U0101, U0121 U0140 C0045, C0050 in the body control module, electronic brake control module, engine control module, or the transmission control module. There may be multiple loss of communication codes current or history for high speed General Motors Local Area Network. Inspect the connections at connector X411 for corrosion due to the location of the connector under the vehicle by the rear wheel.
PIT4916D
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIT4995D
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
PIT5171D
This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern.
PI0091B
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
02-08-42-001H
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
15-00-89-004
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
PIC6087
This Preliminary Information communication provides information to the technician about Apple devices is inoperative or freezing when using the device via USB cable after an IOS8.x.x update. Technician will need to delete the radio from the phone and the phone from the radio. Also close out all apps on the device if it is an iPhone.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5282
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
PIT5199B
This Preliminary Information communication provides information to the technician about vehicles that may have a high pitched whistle or wind noise from the driver?s side mirror area between speeds 25 to 52 mph. Technician will need to use a rubber mallet and lightly tapping on the belt molding moving it toward the (A) pillar area. Then remove the belt molding, use a suitable piece of rubber and glue it to the back side of the of the belt molding to extend it to fill the gap.
PIP5122C
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
15-00-90-002
This informational bulletin provides information to service personnel on the critical importance of installing the correct replacement spin-on oil filter when servicing.
05-08-46-009D
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only).
PIP4919D
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIC5161E
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver?s door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
12-07-30-001E
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
13-08-116-001B
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
00-05-22-002O
This informational bulletin provides technicians with a brake lathe calibration procedure.
PIP5277
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have a resonance type vibration occurs between 40 to 60 MPH. In most cases the engine must be under a slight load such as Air Conditioning compressor engagement, light throttle, and in 6th gear Torque Converter Clutch applied. Technician will relax the engine and transmission mounts, then the exhaust system by loosening the front pipe studs. Also work down the system disconnecting one exhaust hanger at a time. Then take the vehicle on a test drive to verify there was improvement. If additional steps are required place two sets of exhaust dampeners one set before and one set after the front catalytic converter. It may be required to move the pair of dampeners along the exhaust system to get the best results.
PIT5236C
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
13-00-89-008A
This informational bulletin communicates GM wiring repair strategy information.
PI1440
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.
04-00-89-015J
This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.
09-00-89-016D
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
PI1437
This preliminary informational bulletin provides repair information for a customer concern of pop or click noise when front seat is moved forward or backward.
12-06-01-008B
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
15-00-90-001
This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter.
02-07-30-029X
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
14882
14882 - SPECIAL COVERAGE. CERTAIN VEHICLES EQUIPPED WITH A 2.4L ENGINE (LAF, LEA OR LUK) THAT HAVE EXPERIENCED HIGH OIL CONSUMPTION MAY ALSO EXPERIENCE A FROZEN AND/OR PLUGGED PCV (POSITIVE CRANKCASE VENTILATION) SYSTEM DURING COLD WEATHER OPERATION. THIS CONDITION MAY INCREASE CRANKCASE PRESSURE LEADING TO A REAR CRANKSHAFT SEAL OIL LEAK. IF THE OIL LEAK IS IGNORED OR NOT NOTICED, AN ENGINE CLATTER NOISE MAY BE NOTICEABLE AND/OR THE ENGINE PRESSURE WARNING LIGHT MAY ILLUMINATE. IF THIS CONDITION IS NOT CORRECTED, CONTINUED DRIVING WITH ENGINE NOISE AND/OR THE ENGINE OIL PRESSURE LIGHT ILLUMINATED MAY DAMAGE THE ENGINE. DEALERS ARE TO PERFORM A CRANKCASE PRESSURE CHECK, AND IF REQUIRED, REMOVE THE INTAKE MANIFOLD AND CLEAR THE PCV ORIFICE.
15-08-44-001
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-00-89-003
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).
PI1043B
This preliminary informational bulletin adds the 2015 model year to information to correct a customer concern on opening hood when hood primary latch release cable is inoperative.
05-06-04-060A
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.
PIC6070
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
PI0950A
This preliminary informational bulletin provides repair information to correct a customer concern of on an automatic transmission fluid leak.
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
13-06-01-003G
This technical bulletin provides diagnostic and repair information on performing an oil consumption test and/or installing piston and piston ring kit to correct a customer concern for excessive oil consumption.
08-03-10-004B
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.
05-00-89-055E
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
PIP4548D
This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Technician should inspect the respective intake or exhaust camshaft reluctor to see if it has spun on the camshaft. The reluctor cannot be repositioned so the camshaft must be replaced. The new camshafts come with the reluctor already pressed on in the correct position.
15-08-42-001
This informational bulletin communicates GM's position on exterior lighting components ?tinted or smoked? by an outside vendor.
PI1018A
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.
05-03-10-020F
This informational bulletin communicates GM's position on use of nitrogen gas in tires.
PI1404
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement.
05-08-51-001G
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.
01-00-89-010K
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).
06-08-47-001K
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
00-03-10-002I
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
03-06-03-003D
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
11-00-89-004A
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PI0360E
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application.
03-00-91-001G
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
15-06-03-001
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PI1385
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always be re-learned when accessory wheels are installed on the vehicle.
030729004I
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
PIT5236B
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
PI0360D
This preliminary information bulletin advises the technician that there is no update for the customers concerns of the GM remote start doesn't work with the Onstar remotelink phone application.
PI0655A
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
PIP5209B
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIC5954B
This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Technician will need to reprogram the seat heater control module using Service Programming System with the latest calibration to address the concern.
PIC5954A
This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Technician will need to reprogram the seat heater control module using Service Programming System with the latest calibration to address the concern.
030848006J
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
This information provides the proper way to install the floor mats .
100089005D
This warranty informational bulletin advised the technician that when performing a wiring repair, more information is required.
PI1120B
This preliminary bulletin provides a procedure to lubricate the windshield molding to correct the customers concern of the windshield creaking or popping when cold.
PIT5236A
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
PIT5355
This Preliminary Information communication provides information to the technician about vehicles that have creak, pop, tick or itch type noise from the windshield area while driving the vehicle when the ambient temperature is below ?6.5° Celsius (20° Fahrenheit). If the technician has completed the latest version of PI1120 and the concern is still present the windshield will need to be replaced.
PI0800D
This preliminary bulletin provides a procedure to reprogram the power steering module to correct the customers concern of the MIL on and a drop in power steering assist.
140601002A
This technical bulletin provides a procedure to replace the crankshaft bearings and rear oil seal to correct the customers concer of an oil leak.
PI-0800-A
BUICK/CHEVROLET/GMC/OPEL: POWER STEERING ASSISTANCE MALFUNCTIONS WHILE EITHER TURNING LEFT OR RIGHT. MODELS 2012 OPEL AMPERA, VOLT, 2013 LACROSSE, REGAL, EQUINOX, MALIBU, TERRAIN, OPEL INSIGNIA. *PE UPDATED 08/1/2013 *JS UPDATED 11/25/2013 *JS UPDATED 1/13/15. *PE
PI11020B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4915D
Normal Characteristic - Sub-woofer Is Inoperative With a 2.4L Engine.
PIT5074H
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
04-00-89-015I
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
06-00-89-026M
This warranty bulletin provides labor operation numbers for customer concerns that can't be duplicated.
PIC5492C
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
05-06-04-022L
This informational bulletin provides information on top tier fuels and what brands are available.
14D115
Please return service inventory of ACDelco part numbers 20964305, 20964306, 20877116, and 20898936 (Date Codes 077 13166 - 077 13228, June 15, 2013?August 16, 2013).
PIP5029F
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
10-08-42-001D
This technical bulletin provides a procedure to check the headlamp wiring connector and replace if damaged.
G-205009
14232 - SPECIAL COVERAGE. SOME VEHICLES MAY HAVE INCREASED FRICTION IN THE STEERING SYSTEM. THIS COULD CAUSE THE STEERING WHEEL TO STICK IN THE STRAIGHT-AHEAD POSITION AFTER DRIVING LONG DISTANCES ON A STRAIGHT HIGHWAY. THE STEERING WHEEL CAN BE TURNED BUT IT MAY REQUIRE INCREASED EFFORT. DEALERS ARE TO 1) REPLACE THE STEERING GEAR ON 2010-2012 MODEL YEAR VEHICLES; OR 2) REPROGRAM THE POWER STEERING CONTROL MODULE ON 2013-2014 MODEL YEAR VEHICLES.
10-08-98-002A
This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit.
99-04-20-002I
This informational bulletin explains a normal condition for what and how the drive line can clunk.
PIP5244A
This Preliminary Information communication provides information to the technician about vehicles that have poor fuel economy. Dealer should obtain a detailed description of our customer?s driving habits on a daily basis, such as miles driven, roads taken, and speeds driven. Technician should perform an initial fuel economy evaluation and actual driving evaluation.
PI1358
This preliminary bulletin provides a procedure to repair the carpet by installing retainers, from pulling loose from the drivers body hinge pillar trim panel.
PIP5244
This Preliminary Information communication provides information to the technician about vehicles that have poor fuel economy. Dealer should obtain a detailed description of our customer?s driving habits on a daily basis, such as miles driven, roads taken, and speeds driven. Technician should perform an initial fuel economy evaluation and actual driving evaluation.
09-06-04-026H
This informational bulletin was created to help technician identify non GM calibrations for the gasoline engines and the damages that may be caused by aftermarket calibrations
PIT5264B
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
110089005H
dealer Empowerment Labor Operations and Customer Enthusiam
130089004J
Car and Truck Fix it Right the First Time Issues
14232
Special Coverage Adjustment ? Power Steering Stick-Slip
990420002I
Information on Driveline Clunk Noise
PIT5099A
A/C Blows Warm Or Poor Performance.
14-00-89-003A
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time
07-06-04-025K
This informational bulletin was provides information for the technician of cold start ticking noises in the engine compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
PI1218B
This preliminary bulletin provides information to reset the phone and factory reset of the radio to correct the customers concern of the iphone connection concerns.
06-08-43-003E
This informational bulletin explains how to care for wiper blades.
PIP5232A
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
04-00-89-015H
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
PI1098A
This preliminary bulletin provides a procedure on how to cold crank test a battery in a vehicle.
PIC6036
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC5611C
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP3333C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent engine misfire and a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0300, P0301, and/or P0304. Technician will need to follow published Service Information diagnostics first. If the Service Information diagnostics do not isolate a cause for this concern, inspect the inside of the fuel rail and/or fuel tank for fuel contamination. f fuel contamination is present, refer to the "Fuel System Cleaning" procedure in Service Information. Dealer will need to advise the customer to only use fuel from high quality high volume Top Tier fuel stations.
04-06-04-047M
This informational bulletin states that it no longer valid and refers to a new bulletin.
08-08-44-015E
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
This informational bulletin provides information on how to use floor mats.
12187C
12187C - CUSTOMER SATISFACTION PROGRAM (REVISED EXPIRATION DATE). CERTAIN VEHICLES THAT WERE SERVICED WITH AN INCORRECT CALIBRATION, MAY HAVE A CONDITION IN WHICH THE AUTOMATIC CRASH RESPONSE SYSTEM MAY NOT WORK AS INTENDED BECAUSE OF A SOFTWARE PROBLEM. THE AUTOMATIC CRASH RESPONSE SYSTEM IS INTENDED TO ENABLE THESE VEHICLES TO NOTIFY ONSTAR® IF THEY ARE INVOLVED IN CERTAIN TYPES OF CRASHES. THE SOFTWARE PROBLEM WE FOUND AFFECTS THE VEHICLES ABILITY TO NOTIFY ONSTAR® IN CRASHES THAT MEET THE SEVERITY PARAMETERS FOR AUTOMATIC CRASH NOTIFICATION BUT DO NOT TRIGGER AIRBAG DEPLOYMENT, SUCH AS CERTAIN REAR END CRASHES. IN CRASHES WITH AN AIRBAG DEPLOYMENT, THE AUTOMATIC CRASH RESPONSE SYSTEM WORKS AS DESIGNED. THIS CONDITION DOES NOT AFFECT THE DEPLOYMENT OF THE AIRBAGS OR THE SAFETY BELT PRETENSIONERS, WHICH REDUCE SLACK IN THE SAFETY BELT IMMEDIATELY AFTER IMPACT. THE AIRBAGS AND SAFETY BELT PRETENSIONERS WILL DEPLOY AS DESIGNED. A VEHICLE OCCUPANT WILL BE ABLE TO CONTACT AN ONSTAR® EMERGENCY ADVISOR BY PUSHING THE ONSTAR® EMERGENCY BUTTON. DEALERS ARE TO REPROGRAM THE SENSING AND DIAGNOSTIC MODULE (SDM).
05-06-04-022K
This informational bulletin provides information on top tier fuels and what brands are available.
10-08-44-006C
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.
07-00-89-036G
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
PIP5096C
This Preliminary Information communication provides information to the technician about vehicles with a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P011, P0014, P0021, and or P0024. During inspection if no other drivability concerns found inspect the engine EUN sticker for an (A) before the sequence number. If there is an "A" before the sequence number then replace the OCV/Cam Actuator Solenoid Valve with a replacement "service" valve.
02-00-89-002N
This informational bulletin provides additional information to the technicians and how to submit a field product report.
10-00-89-006E
This information bulletin provides the dealers on how to submit a product information report.
PB-12187-A
BUICK/CADILLAC/CHEVROLET/GMC: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOFTWARE PROBLEM FAILS TO WORK, AS INTENDED, IN AUTOMATIC CRASH RESPONSE SYSTEM AND MAY NOT MEET SEVERITY PARAMETERS FOR CRASH NOTIFICATION IN CERTAIN REAR END CRASHES. MODELS 2012 SRX; 2013 VERANO, CRUZE, EQUINOX, VOLT, TERRAIN. *PE UPDATED 11/28/12. *PE UPDATED 12/9/14. *PE
PIP-5096
CADILLAC/BUICK/CHEVROLET/GMC: DUE TO CAM ACTUATOR CODES SET - DTC P0011, DTC P0014, DTC 20024, DTC P0021 AND NO OTHER DRIVABILITY ISSUES, THE ENGINE EUN STICKER SHOULD BE INSPECTED, BEFORE REPLACING ACTUATOR. *PE
G-199041
14289 - SPECIAL COVERAGE. ON SOME VEHICLES, EQUIPPED WITH E85 FLEX FUEL CAPABILITY (FHS), THE FLEXIBLE FUEL SENSOR MAY BECOME INOPERATIVE DURING NORMAL OPERATION DUE TO AN ELECTRICAL FAILURE CAUSED BY ROAD SALT AND OTHER ENVIRONMENTAL CONTAMINANTS. WITH A FAULTY FLEX FUEL SENSOR, THE SERVICE ENGINE SOON LIGHT WILL ILLUMINATE AND REMOTE START WILL BE INOPERATIVE. DEALERS ARE TO REPLACE THE FUEL FLEX SENSOR. THE REPAIRS WILL BE MADE AT NO CHARGE TO THE CUSTOMER.
03-06-03-004M
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
09-00-89-002J
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
PI1218A
This preliminary bulletin provides information to reset the phone and factory reset of the radio to correct the customers concern of the iphone connection concerns.
PI1296
This preliminary bulletin provides additional diagnoses for engine misfires, popping noise after cylinder head or fuel rail repair.
00-03-10-006K
This informational bulletin provides the technician with information on tire radial force variations and how to use it.
13-02-32-001B
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.
PIC5901A
This Preliminary Information communication provides information to the technician about the Samsung Galaxy S III will lose connection to the vehicle or does not connect to the vehicle. Customer can update the phone with the latest Android system software which begins with Android 4.4 version.
PIP5209A
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIP5216
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
14-06-01-002
This technical bulletin provides a procedure to replace the crankshaft bearings and rear oil seal to correct the customers concer of an oil leak.
PI1290
This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose mirrior and/or bracket fell off.
13-02-32-001C
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.
PI1004A
This preliminary bulletin provides a procedure to repair the engine wiring harness if the customer states MIL on multipul service messages displayed.
PI-1004
GM: MALFUNCTION INDICATOR LAMP MAY BE ON. SERVICE POWER STEERING, SERVICE VEHICLE, OR SERVICE STABILITRAK MESSAGES MAY BE DISPLAYED ON DIC. *JS UPDATED 11/12/14. *PE
SB-13-02-32-001
BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE
SCB-14289
BUICK/GMC/CADILLAC/CHEVROLET: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO ELECTRICAL FAILURE, FLEXIBLE FUEL SENSOR IS INOPERATIVE DURING NORMAL OPERATION, CAUSED BY ENVIRONMENTAL CONTAMINANTS SUCH AS ROAD SALT. *PE
PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
99-01-39-004F
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5759A
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4911X
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
00-06-01-012E
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
12-03-10-001B
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
12-09-41-002B
The informational bulletin explains how items on the passenger seat may cause the PPS to chime or the passenger airbag light turns on if electronic devices or conductive objects are placed on the seat.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
02-00-89-002M
This informational bulletin provides additional information to the technicians and how to submit a field product report.
PI0938A
This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues.
10-00-89-006D
This information bulletin provides the dealers on how to submit a product information report.
07-06-04-025J
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment may be caused by the fuel pump and/or the fuel injectors and no
10-08-46-001B
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
PIP4902H
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
120310001B
Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip
120941002B
Passenger Presence System (PPS) May Command Seat Belt Reminder Chime Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
14-00-89-003
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.
PIC5869A
This Preliminary Information communication provides information to the technician that the compact disc player is unable to pause a song. These vehicles were not built with a pause button. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT5302
Turn Signal Indicator Does Not Match Audible Warnings
PIV5869A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Recalls
Vehicle Recalls
050308002F
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
PI1266
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.
PI0373B
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
PIP5207
This preliminary bulletin provides an procedure to reprogram the ECM for high altitude vehicles that have no start or long crank time.
PIC5088E
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
05-00-89-029C
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
12-00-89-002B
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PI1259
This preliminary bulletin provides information of a normal condition for the customers concern of the IPC and center instrument panel lighting isnt bright enough when vehicle is first started in a dark area.
03-00-89-006K
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
PIP4653E
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
PI0663F
Factory Settings Option Inoperable, Radio Display Information May Not Match.
09-03-10-013B
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
G-193017
13120C - SERVICE UPDATE (REVISED EXPIRATION DATE). THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO REPROGRAM THE TRANSMISSION CONTROL MODULE (TCM) ON CERTAIN VEHICLES, EQUIPPED WITH 6-SPEED AUTOMATIC TRANSMISSION. THE TORQUE CONVERTER CLUTCH SOLENOID IN THE TECHM CAN STICK DUE TO DEBRIS IN THE TRANSMISSION. WHEN THE VEHICLE IS AT THE END OF A COAST-DOWN, AS THE VEHICLE IS COMING TO A STOP, A STUCK SOLENOID WILL FAIL TO RELEASE THE TORQUE CONVERTER CLUTCH. THIS KEEPS THE ENGINE DIRECTLY CONNECTED TO THE DRIVEN WHEELS. AS THE VEHICLE STOPS, THE ENGINE SPEED WILL BE PULLED DOWN BELOW NORMAL IDLE SPEED AND THE ENGINE MAY STALL. THE VEHICLE CAN BE IMMEDIATELY RESTARTED AND DRIVEN. THE REPROGRAMMING WILL INSTALL A REVISED CALIBRATION TO CORRECT THIS CONDITION.
02-07-30-029W
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
12-07-30-001D
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
PI1223A
This preliminary bulletin explains a normal condition of a customers concern of a rough idle and black smoke on cold starts.
03-06-03-004L
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
00-03-10-006J
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
03-03-10-007I
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
13-06-01-003F
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs of consumption or oil leaks have been validated.
12-08-132-001B
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the cause if diagnostics finds no problems to that point.
13-00-89-004I
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
06-00-89-029J
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
PI1235
This preliminary bulletin provides information to the technician, to check for loose grounds and the correct labor op to use
PI1233
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
02-07-30-029V
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
10-03-08-003B
This technical bulletin provides a procedure to add greese to the strut and jounce bumper, to stop the customers concern of the front suspention or strut making noise.
PIP5062C
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
130601003F
Excessive Oil Consumption
13120C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI-1235
GENERAL MOTORS: DUE TO LOOSE GROUND TERMINAL CONNECTIONS, IN SOME VEHICLES AND TRUCKS EXPERIENCE, ACCESSORIES MALFUNCTIONS, DIC MESSAGES, IPC WARNING INDICATORS, SES LIGHT ON. *PE
PIC-5428
GM: THE BRAKE, TRACTION, OR STABILITY LIGHTS ARE ON BECAUSE OF DEBRIS STUCK ON THE WHEEL SPEED SENSOR. UPDATED ON 06/15/2011. *KB UPDATED ON 06/20/2011. *RM UPDATED 6/27/11. *PE UPDATED 10/3/11. *PE UPDATED 05/08/2013 *JS UPDATED ON 7/9/2013. *KB UPDATED 7/28/14. *PE
PIC5428F
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
09-00-89-002I
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
PIP4919C
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
01-08-42-001J
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
09-00-89-029L
This informational bulletin explains how to cut a new key or how to get a precut key from GM.
PI1223
This preliminary bulletin explains a normal condition of a customers concern of a rough idle and black smoke on cold starts.
PIP5191
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIC5491F
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT3099L
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1218
This preliminary bulletin provides information to reset the phone and factory reset of the radio to correct the customers concern of the iphone connection concerns.
PI0814D
This preliminary bulletin provides a procedure to replace the power steering hose, generator and evaporative hose to correct the customers concern of steering shudder at low speeds.
13-00-89-004H
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
130089004H
Car and Truck Fix it Right the First Time Issues
130601003E
Excessive Oil Consumption
1406130001
High Voltage Safety ? High Voltage Disabling
PI0663E
Factory Settings Option Inoperable, Radio Display Information May Not Match.
PIT4911W
Navigation Radio, Radio, Amplifier, Human Machine Interface.
03-06-03-004K
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
13-06-01-003E
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs of consumption or oil leaks have been validated.
SB-0000187949-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-00-89-004G
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIC5374C
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
PIC5959A
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIT5264
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIC4801F
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
130089004G
Car and Truck Fix it Right the First Time Issues
PI1186
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI1189
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
PIC5491E
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
12-07-30-001C
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
PIT5256
This Preliminary Information communication provides information to the technician about vehicles that the headlamps do not turn on during low ambient light conditions such as nighttime when unlocking their vehicle with the remote transmitter. Technician will need to ensure that the Vehicle Locator Light feature has been turned on in the Vehicle Personalization menu. If the feature is turned on then the technician will need to update the Body Control Module with the latest calibrations in Tis2Web.
PIT5119C
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
09-03-10-016B
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
10-08-64-002C
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
12-03-10-001A
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
12-03-10-002A
This informational bulletin provides the technician the proper way to install and torque the wheel.
PI0737A
This preliminary bulletin provides information on how to set the rear electric child locks.
PIP5122B
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
05-03-10-020E
This informational bulletin explains the use of Nitrogen in GM tires.
07-03-10-008D
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
08-03-10-006E
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
PI0388D
This preliminary information provides a procedure to repair the seat belt webbing and latch by rolling it back over.
03-08-46-004O
This informational bulletin provides information on part restriction and ordering of Onstar vehicle communication modules.
13-00-89-004F
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIP4990A
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
PIT4943C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIT4945F
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
02-08-98-002E
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
05-08-48-001D
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
99-01-39-004E
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
PI1120A
This preliminary information bulletin provides a procedure on how to correct the customers concern of a creak or popping from the windshield area when cold.
PIT5076D
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PI0360C
This preliminary informational bulletin provides service information to the dealer technicians that the remote start will not work with the ONSTAR REMOTE Link applcation
PIP5180
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIC5954
This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIC5453A
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
120310001A
Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip
120310002A
Proper Wheel Installation and Wheel Torque Techniques
130089004F
Car and Truck Fix it Right the First Time Issues
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
990851007F
Refinishing Aluminum Wheels
PIE0280
Engineering Information.
04-00-89-053F
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
PIC5959
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIP5093A
This Preliminary Information communication provides information to the technician about vehicles that may have an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures. The technician may find the oil leak is coming from the rear main seal. Technician will need to check for proper thermostat operation by following thermostat Diagnosis as outlined in Service Information and replace the thermostat as necessary. Also the technician will remove the cam cover, inspect the positive crankcase ventilation baffle inside, and replace the cam cover if obvious sludge build up is present. Any debris in the positive crankcase ventilation pipes, hoses, the positive crankcase ventilation nipple on the cam cover, and the throttle body should be cleaned out. Technician should inspect the related positive crankcase ventilation hoses/connections for potential damage and replace if necessary. Run the engine at operating temperature for 15 minutes at idle. Then turn the engine off, and drain the engine oil for at least 15 minutes to remove all oil and condensation or water from the crankcase. Follow Service Information repair procedures to repair any oil leaks that were induced as a result of the frozen positive crankcase ventilation system and excessive crankcase pressure. Technician should insure the Engine Control Module calibrations have been installed to adjust the engine oil life monitor to a maximum of 7,500 miles (12,070 KM) as well.
PIC5161D
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver's door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
11-00-89-002B
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
PIP4670D
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP4919B
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP4924D
This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and a misfire. Technician may find Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, and or P216D. Technician will need to inspect the fuel injector wiring harness for rub through or internal wire opens. If this concern is found repair or replace the injector harness as needed.
07-06-04-025I
This informational bulletin was provides information for the technician of cold start ticking noises in the engine compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
PIP4112N
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP3140F
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP4384H
This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website.
PIP4964C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
08-08-44-029D
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
04-00-89-015G
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
PIP4919A
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
04-00-89-015F
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
07-00-89-037G
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to its customers.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PIC5137P
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5598J
This Preliminary Information communication advises the technician that the part restriction on the electric power steering module for NJ1 part numbers has ended. Dealer can order parts directly through your parts department.
10-00-89-006C
This informational bulletin provides directions on submitting different PIRs
PI0324F
This preliminary bulletin provides a procedure to aid in diagnosing a possible faulty front transmission oil pump.
08-08-44-015D
This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.
13-00-89-004E
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
PI1128
This preliminary bulletin provides a procedure to replace the right rear hub bearings and seals to correct the customers concern of noises from that area.
PI0754A
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason.
05-00-89-072C
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
130089004E
Car and Truck Fix it Right the First Time Issues
PI1120
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0592C
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491).
PIT5063D
This Preliminary Information communication provides information to the technician with a diagnostic tip service steering message or service stability message. Technician may find a Diagnostic Trouble Code C056E Sym 42 and a Diagnostic Trouble Code C0569 Sym 3A setting after a new steering gear assembly was installed. If Diagnostic Trouble Code C0710 Sym 71 is set it must be addressed firth before performing a steering gear "set-up" in Service Programming System. Steering Angle Sensor module Diagnostic Trouble Code C056D Sym 00 and it must be address first. Technician should be advised that Diagnostic Trouble Codes DTC C056E Sym 42 or C0569 Sym 3A will set when a steering gear assembly was replaced without Service Programming System programming.
13-00-89-004D
This informational bulletin provides an update for 13-00-89-004C to include updated information.
PIC5611B
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
00-06-01-026E
This informational Bulletin provides a revision for 00-06-01-026D to add the 2014 model year.
PIP5029E
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PI0018B
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance.
PIT5200A
This Preliminary Information communication provides information to the technician about vehicles that have a Heater-Vent-Air Conditioning system will start blowing cold air without being requested. Technician may find Diagnostic Trouble Code B101E sym 4B. Technician will need to inspect and repair corrosion at the starter connections.
04-06-04-047L
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
PI1098
This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.
PIT4911V
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
09-06-04-015B
This informational bulletin provides a revision for 09-06-04-015A to add the 2012-2014 model years.
10-08-110-001A
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
110089005G
Recent information and updates for Enable and Empower Project
130089004D
Car and Truck Fix it Right the First Time Issues
PI-0018-B
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
PIC5932
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT4995C
Rear Wiper and/or Front Rain Sense Wipers.
PIC5862
This Preliminary Information communication provides information to the technician about vehicles that have brake lights remain on with the vehicle off and parked and/or the vehicle battery goes dead. Technician will need to inspect for aftermarket parts.
PIP4959D
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIC5491D
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIC5492B
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIP5095B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIT5236
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
110089005F
Enable and Empower Project
120601008
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to Enhance Customer Service Experience
120601008A
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to Enhance Customer Service Experience
130089004C
Car and Truck Fix it Right the First Time Issues
130089010
PAC Courtesy Transportation Assistance Program
PI0058A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0800C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC-5862
GM: SOME VEHICLES MAY EXPERIENCE A CONDITION IN WHICH THE BRAKE LIGHTS REMAIN WHEN THE VEHICLE IS OFF AND PARKED. THE BATTERY MAY ALSO GO DEAD. MAKE/MODELS ALSO INCLUDED: BUICK ENCORE/LACROSSE/REGAL MODEL YEAR 2014, CADILLAC SRX/XTS MODEL YEAR 2014, CHEVROLET EQUINOX/SILVERADO 1500/TRAX MODEL YEAR 2014, AND GMC SIERRA/TERRAIN MODEL YEAR 2014. *JS
PIT3237G
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
PIP5062B
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
PIC5491C
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIT3099K
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130601003C
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
130601003D
Excessive Oil Consumption
990940005G
Seat Belt Extender Availability
PI0814C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI1067
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4911U
Navigation Radio, Radio, and Integrated Center Stack.
PIT4994D
Liftgate Rattles Over Rough Roads.
SB-10-06-01-003C
CADILLAC/BUICK/SATURN/PONTIAC/CHEVROLET/ GMC: DUE TO AN ABNORMAL ENGINE NOISE OR INTERNAL BY AN OIL FILTER MISAPPLICATION, FILTER DEBRIS MAY BE TRANSFERRED THROUGHOUT ENGINE AND MAY RESULT IN ENGINE DAMAGE. MODEL 2004-06 RENDEZVOUS, 2005-14 LACROSSE, 2008-14 ENCLAVE, MALIBU, EQUINOX, 2010-14 SRX, TERRAIN, 2013-14 ATS, XTS, 2009-14 TRAVERSE, 2014 IMPALA, 2007-14 ACADIA, 2007-09 G6, AURA, 2008-09 TORRENT, VUE, 2007-10 OUTLOOK. *PE
03-08-46-004N
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM).
01-03-10-003K
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.
PI1043
This preliminary information bulletin provides information on opening the hood when the primary latch release cable is inoperative.
06-00-89-026L
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIC5904
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
06-06-01-010B
This informational bulletin provides information on close-coupled converter and engine replacement.
PIP5029D
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
99-09-40-005G
This informational bulletin provides information on availability for the seat belt extender.
PIC5901
This Preliminary Information communication provides information to the technician about the Samsung Galaxy S III will lose connection to the vehicle or does not connect to the vehicle. Customer can update the phone with the latest Android system software which begins with Android 4.4 version.
00-03-10-003R
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
PIE-0251-B
GM: THE ENGINE MAY BE LEAKING FROM THE FRONT COVER OR OIL FILTER ADAPTER. THIS IS NOT A RECALL. *JS
PIP4112M
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4112L
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIT5063C
Service Steering Message or Service Stability Message.
PI0233D
This preliminary information bulletin provides information on inaccurate or slow response of outside air temperature display.
13-06-01-003B
This technical bulletin provides a procedure for oil consumption test and set up including piston, connecting rod and bearing due to excessive oil consumption and/or need to add oil between oil changes.
03-06-03-004I
This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.
02-07-30-029U
This informational bulletin provides information for the PQC assembly replacement process.
PI1018
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
10-00-89-010C
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
13-00-89-008
This informational bulletin provides information for GM wiring repair.
10-00-89-009B
This informational bulletin provides information on key code security and information on GM key code look up applications.
130089008
GM Wiring Repair Strategy Information
130090001
Information for Engine Oils Used in 2014 Model Year Vehicles
130232001B
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
130601003A
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
130601003B
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
PI1010
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5257C
Service Stability Message With Code U0710
09-00-89-029K
This technical bulletin provides a revision for 09-00-89-029J to add the 2014 model year and to add the Impala, Spark, Spark EV, Silverado and Sierra.
PI1009
This preliminary informational bulletin provides information for Diagnostic Tips for DTCs P0097, P00F4, P0113, P2229 and/or P0102 Set
13-06-01-003
This technical bulletin provides a replacement for PIP5025F to advise engine replacement is no longer necessary if "zebra stripes" are present and to outline a related repair procedure.
PIT5216
This Preliminary Information communication provides information to the technician about vehicles that have a momentary or intermittent instrument panel cluster message or messages and would include a blank radio display. Technician will need to inspect the connector X401 for terminal corrosion due to water intrusion.
PI1004
This preliminary informational bulletin provides information for Malfunction Indicator Lamp (MIL) On, Service StabiliTrak, Power Steering or Vehicle Soon Message Displayed on DIC.
PIT3117H
This Preliminary Information communication provides information to the technician of part numbers that are missing from the service information documents. The following part numbers are for a cam nut that is available to adjust the rear toe 11519455, 11562237, 11570574.
04-00-89-015E
This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S. version of Bulletin 12-00-89-003.
03-00-89-006J
This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.
05-09-40-002G
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
PI0999
This preliminary informational bulletin provides information for Malfunction Indicator Lamp (MIL) On,Torque Converter Clutch Sticking, Engine Shudder When Stopping, DTC P0742 Set Concern.
PI0865C
This preliminary informational bulletin provides a revision for PI0865B to update the Parts Information table to include Usage and update the Warranty Information.
PI0880C
This preliminary informational bulletin provides a revision for PI0880B to update the Condition/Concerns and Warranty Information.
PI0855C
This preliminary informational bulletin provides a revision for PI0855B to update the Recommendation/Instructions.
12-09-41-002A
This technical bulletin provides information on a revision for 12-09-41-002 to add the 2014 model year and update the models.
PIP5122A
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
PI0800B
This preliminary informational bulletin provides a revision for PI0800A to update the Warranty Information.
07-08-49-020H
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
PIP5122
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
12-02-32-002A
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
13-02-32-001A
This technical bulletin provides a revision for 13-02-32-001 to update the models information.
PI0767B
This preliminary informational bulletin provides a revision for PI0767A to remove the build date and update the Recommendation/Instructions section and Warranty Information.
120232002A
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Pressure Hose During Extreme Low Temperature Operation (Replace Power Steering Fluid)
120941002A
Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
130089006
Changes in Powertrain Warranty Coverage Effective with 2010 Model Year
130232001A
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
PI-0011A
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
PI-0999
GM: SOME VEHICLES MAY EXPERIENCE AN ENGINE SHUDDER UPON STOPPING. MALFUNCTION INDICATOR LAMP IS ON. CLUTCH IS STICKING. *JS
PIC5869
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP-5122-A
GM: SOME VEHICLES MAY EXPERIENCE OCCASIONAL POP SOUNDS FROM THE FUEL TANK. THIS MAY OCCUR AFTER A COLD START OR EVAP PURGE. ALSO INCLUDED MODELS CHEVROLET EQUINOX AND GMC TERRAIN MY 2014 *JS
PIT4994C
Liftgate Rattles Over Rough Roads.
00-05-22-002N
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
PI0011C
This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update Warranty Information.
13-00-89-006
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year.
PI0086E
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry® Phone - Bluetooth® Issues Concern.
PI0574A
This preliminary informational bulletin provides a revision for PI0574A to include the 2013-2014 model year vehicles, update the covered models and the Recommendation/Instructions section.
08-06-01-006D
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
13-02-32-001
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
PIT5214
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
G-166208
13120B - Service Update (population added; expiration date extended). Reprogram the transmission control module (TCM). The torque converter clutch solenoid in the TECHM can stick due to debris in the transmission. When the vehicle is at the end of a coast-down, as the vehicle is coming to a stop, a stuck solenoid will fail to release the torque converter clutch. This keeps the engine directly connected to the driven wheels. As the vehicle stops, the engine speed will be pulled down below normal idle speed and the engine may stall. The vehicle can be immediately restarted and driven. The reprogramming will install a revised calibration to correct this condition.
SB-0000166208-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
02-08-98-002D
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
11-00-90-001B
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
09-00-89-008A
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
PI0592B
This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.
PI0602A
This preliminary informational bulletin provides a revision of PI0602 to add the 2013 and 2014 model years.
07-03-10-015C
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.
05-08-48-001C
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
05-03-07-009F
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.
13-00-89-004B
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PI0855B
This preliminary informational bulletin provides a revision of PI0855A to add the 2013 Buick Encore.
PIC5865
This Preliminary Information communication provides information to the technician about vehicles that have "There are Traffic Events Along the Route" voice prompt message while on a navigation route. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
06-00-89-026K
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.
10-00-89-016A
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the Labor Operation graphic.
09-03-16-002B
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.
09-07-30-018D
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.
PI0785B
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model and update the Parts and Warranty Information.
PIP4902G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PI0604C
This preliminary informational bulletin provides a revision to update the model information and information under Oil Pump Assembly.
10-00-89-005C
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
11-00-89-007C
This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation List.
PI0388C
This preliminary informational bulletin provides a revision of PI0388B to add the Cadillac XTS model, graphics, improved Instructions and Warranty Information.
07-00-89-037F
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
09-00-89-016C
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
03-08-48-006I
This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.
PIT4720C
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
03-06-03-004H
This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.
090730018D
Change in Automatic Transmission Add Condition Documentation and Claim Submission
110089005E
This bulletin is being revised to add additional Mandatory Minimum Tables and additional information concerning Policy decision making. Please discard Corporate Bulletin Number 11-00-89-005D (Section 00 ? General Information).
110090001B
Global Information for GM dexos 1? and dexos 2?, Engine Oil Specifications
130089004B
Car and Truck Fix it Right the First Time Issues
130232001
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
13120B
Service Update for Inventory Vehicles Only Torque Converter Clutch Sticking Expires April 30, 2014
PI-0388-C
GENERAL MOTORS: SEAT BELT COULD BECOME TWISTED WITH THE LATCH PLATE. *KB
PIC5322C
Heated Seat Operation After Performing A Remote Vehicle.
PIC5428E
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
PIE-0246A
GENERAL MOTORS: CUSTOMERS MAY COMMENT ABOUT THE TIRE PRESSURE MONITOR SYSTEM OR CHECK TIRE PRESSURE LAMP ILLUMINATED. *KB
PIE0246A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5030E
Intermittent No Crank When Ignition Key Is Turned To The Crank.
PIT5074G
Terminal Test Probe And Replacement Terminal.
PIT5171C
Service Stability, Traction, ABS Rear Wheel Speed DTC Or Chassis Expansion
13-00-89-005
This technical bulletin provides Warranty Administration - New Labor Codes information.
PI0855A
This preliminary information bulletin provides a revision of PI0855 to update Recomondation/Instructions.
G-164258
13120A - Service Update (revised population). The torque converter clutch solenoid in the TECHM can stick due to debris in the transmission. When the vehicle is at the end of a coast-down, as the vehicle is coming to a stop, a stuck solenoid will fail to release the torque converter clutch. This keeps the engine directly connected to the driven wheels. As the vehicle stops, the engine speed will be pulled down below normal idle speed and the engine may stall. The vehicle can be immediately restarted and driven. Dealers are to reprogram the transmission control module with a revised calibration to correct this condition.
SB-0000164258-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5029C
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
13-00-89-004A
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.
G-163817
13120 - Service Update. The torque converter clutch solenoid in the TECHM can stick due to debris in the transmission. When the vehicle is at the end of a coast-down, as the vehicle is coming to a stop, a stuck solenoid will fail to release the torque converter clutch. This keeps the engine directly connected to the driven wheels. As the vehicle stops, the engine speed will be pulled down below normal idle speed and the engine may stall. The vehicle can be immediately restarted and driven. Dealers are to reprogram the transmission control module with a revised calibration to correct this condition.
PIC4707D
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
PIC4788E
This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods.
SB-0000164278-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0958
This preliminary information bulletin provides a recomondation for an update when Hesitation During Launch and/or Step-in at Low to Moderate Speeds Condition is present.
03-06-03-003C
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
99-04-20-002H
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
PI0950
This preliminary information bulletin provides information on a concern of transmission fluid leak from torque converter housing area.
PIP4924C
This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and a misfire. Technician may find Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, and or P216D. Technician will need to inspect the fuel injector wiring harness for rub through or internal wire opens. If this concern is found repair or replace the injector harness as needed.
PIP4964B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
13-00-89-004
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
PI0572B
This preliminary information bulletin is for information on COAX Repair Kit Availability. Revised from PI0572A
130089003
Vehicle Software Enhancements
130089004
Car and Truck Fix it Right the First Time Issues
130089004A
Car and Truck Fix it Right the First Time Issues
130089005
New Global Labor Codes
13120
Service Update for Inventory Vehicles Only Torque Converter Clutch Sticking Expires April 30, 2014
13120A
Service Update for Inventory Vehicles Only Torque Converter Clutch Sticking Expires April 30, 2014
990420002H
Information on Driveline Clunk Noise
PI0716A
Road Debris (Mud) on Rocker Panel at Front Door Area.
PIE0255
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIE0255A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4913E
Normal Characteristic - Memory Seat Recall Inoperative From Key Fob.
PIT4915C
Normal Characteristic - Sub-woofer Is Inoperative.
PIT4916C
Wind Buffeting Noise With a Rear Window Down.
PIT5012E
Antenna Mast Broken Off From Antenna Base Mount Low Profile Antenna Available
PIT5063B
Service Steering Message or Service Stability Message.
PIT5119B
Intermittent Remote Keyless Entry Inoperative.
SB-13120
BUICK/CADILLAC/CHEVROLET/GMC: IN CERTAIN VEHICLES, THE TRANSMISSION CONTROL MODULE (TCM), 6 SPEED AUTOMATIC, TORQUE CONVERTER CLUTCH SOLENOID STICKS DUE TO DEBRIS, NEEDS REPROGRAMMING. MODELS 2013 ENCLAVE, MALIBU, TRAVERSE, ACADIA, TERRAIN, SRX, XTS. *PE UPDATED 7/1/13. *PE
SB12-08-132-001A
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE
PI0880B
This preliminary information bulletin provides a procedure for reprogramming the radio due to concerns with voice recognition, media data, guidance and DVD playback.
PI0942
This preliminary information bulletin provides a procedure for reprogramming the radio to correct the Bluetooth audio from not being heard, XM advisories from not being shown, voice recognition inoperative and the speaker static pop noise.
13-00-89-003
This technical bulletin provides information on Vehicle Software Enhancements for 2014 and prior GM Passenger Cars and Light Duty Trucks.
11-00-89-005D
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
12-08-132-001A
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to electrical systems that can be affected by devices that are plugged in by the customer.
09-00-89-002H
This informational bulletin provides information for dealers to properly maintain vehicle in inventory.
PI0938
This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
PIC5491B
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT5072D
This Preliminary Information communication provides information to the technician about vehicles that after opening the power liftgate, it will not stay in the full open position and may drift down a few inches before coming to a rest. Technician will ensure the vehicle does not have the incorrect strut mounting brackets installed.
06-00-89-029I
This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats carpet, vinyl.
13-08-116-001A
This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.
PI0934
This preliminary information bulletin provides a procedure for replacing a connector with leads assembly to eliminate the service stabilitrak or antilock brake system warning lamp from being illuminated.
PIT4945E
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
09-06-04-026G
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
PI0814B
This preliminary information bulletin provides a procedure to install a revised generator, power steering gear inlet hose and evap. hose to correct steering wheel shudder during low speed maneuvers.
PI0828A
This preliminary information bulletin provides a procedure for dust intrusion into the passenger compartment when the vehicle is driven in high dust areas.
10-00-89-017Z
This informational bulletin provides information on fix it right for first time issues.
PI0926
This preliminary information bulletin provides a procedure for installing a zip tie for the fuel level sensor to correct the fuel gauge intermittently not reading full when the fuel tank is filled.
PIP5095A
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
00-03-10-002G
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
1308116001A
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
PI0412B
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
PI0893A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5428D
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
PIT4992D
A Notchy Or Stick Slip Feel In The Steering When Turning Near The On-Center Position.
PIT5205
Reduced HVAC Blower Speed Or Reduced A/C Or Heating Performance.
PIP3140E
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
PIP5095
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
990851001C
Paint-less Dent Repair Process
PI0868A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0908
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIE0246
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4384G
This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website.
PIT5176B
Intermittent Theft Deterrent Alarm or Horn or Hood Ajar Message
PIT5199
Whistle Wind Noise From Drivers Side Mirror Area.
PIT5199A
Whistle Wind Noise From Drivers Side Mirror Area.
PIC5137N
This Preliminary Information communication advises the technician that the Electronic Brake Control Module and the Brake Pressure Modulator Valve parts restriction has ended. Dealer can now order the parts directly through your Parts Department without General Motors Technical Assistance Center authorization.
SB-0000157698-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0880A
This preliminary informational bulletin provides information on radio reprogramming due to voice recognition, media data, route guidance, DVD playback concerns.
PI0896
This preliminary informational bulletin provides information on replacement for the auxiliary floor mat retainer due to the floor mat retainer won't seat on the carpet.
00-03-10-006I
This informational bulletin provides information on tire radial force variation.
02-07-30-029T
This informational bulletin provides information on the replacement process for the product quality center.
12-07-30-001B
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
13-08-116-001
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues.
09-06-04-026F
This informational bulletin provides information on suspected tampering on vehicles modifications for identifying non GM ECM calibrations.
SB-0000157300-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0893
This preliminary informational bulletin provides diagnostic information for DTCs P0965, P2719 and P2728.
PIC5611A
This Preliminary Information communication provides information to the technician about the vehicles has no rear camera guideline selection. Technician should be advised that the guideline selection is only available on vehicles equipped with Regular Production Option Code UYS or UEW Navigation Radio. If equipped with UYS or UEW verify the guideline option is turned on.
08-08-51-002A
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
PI0388B
This preliminary informational bulletin provides information on properly repositioning the seat belt webbing/latch plate due to becoming twisted.
03-00-89-013H
This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)
PI0865A
This preliminary informational bulletin provides information on components that must be transferred over from the original engine for the Ecotec 2.4L.
PIP4495D
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
PI0645C
This preliminary informational bulletin provides information on the driver airbag light is flashing in the cluster and/or the passenger airbag ON indicator does not illuminate when the passenger is present when the SDM setup has not been completed after reprogramming.
12315
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty
12315A
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty - Eqluipped with Connected Navigation Radio (UHQ)
PI0882
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0880
this preliminary informational bulletin provides information to reprogram the radio to resolve Voice Recognition, Media Data, Route Guidance, DVD Playback Concerns caused by an internal software concern
11-00-90-001A
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
PIT5176A
This Preliminary Information communication provides information to the technician about vehicles that may have an intermittent "Hood Open" message displayed on the Driver Information Center, intermittent theft deterrent alarm or horn activation, and intermittent remote vehicle start event. Technician will need to replace the hood latch assembly if the vehicle is built before 09/06/2012.
11-00-89-005C
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PI0868
This preliminary information bulletin provides information on reprogramming the radio due to a comment on the radio locking up and becoming inoperative.
PIT5193
This Preliminary Information communication provides information to the technician about vehicles that have an audio pop during engine startup/engine crank. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIC5492A
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIP5062A
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
120941002
Passenger Presence System (PPS) May Command Seat Belt Reminder Chime Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
PI0324E
This preliminary information bulletin provides information on doing a pressure line test prior to replacement and removal of the transmission for conditions relating to No Forward, No Reverse, No Crank, Engine Cranks But Will Not Start.
PI0875
This preliminary information bulletin provides information on how to correctly re-attach the hook loop that keeps the rear compartment spare tire cover in place if one was to come unattached
10-00-89-017X
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
PI0124E
This preliminary information bulletin provides information the proper ways of adjusting the center trim bezel to correct the condition of the CD/DVD will not eject from the instrument panel mounted player.
PIC5161C
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver's door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
PIT5190
This Preliminary Information communication provides information to the technician about vehicles that may have an Antilock Braking System or Stability/Traction indicator lamp on followed by a "Service Stability" message on the instrument panel cluster Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0040 and or C0035 symptom 18 or 0F set in the Electronic Brake Control Module. Technician will need to remove and inspect the effected wheel speed sensor form the knuckle. Technician will replace the hub bearing washer if there is evidence that the tip of the wheel speed sensor has been rubbing.
12-09-41-002
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
PI0774B
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
PIT4911T
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
110090001A
Global Information for GM dexos 1? and dexos 2?, Engine Oil Specifications
SB-PI-0880
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-08-46-004A
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
080846004A
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
000089027G
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PI0865
This preliminary information bulletin provides information regarding all the components that are included when ordering a new service 2.4L Ecotec engine.
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT4733J
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
120310002
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
PIP3720D
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
060089026J
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
10-08-44-004C
This informational bulletin provides information on USB command and control multimedia player interface/list of supported devices.
100844004C
This informational bulletin provides information on USB command and control multimedia player interface/list of supported devices.
PIP5078
This Preliminary Information communication advises the technician that service replacement engine part number 12655766 may be received when a service replacement engine is ordered. Technician will need to part off the original engine.
100089010B
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
120089002A
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
PI0745C
This preliminary informational bulletin provides a procedure on how to correctly check and adjust fuses within the instrument panel fuse block for concerns with components fused through the instrument panel fuse block
PIT4945D
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
010089010J
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
100089017W
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
030846004M
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules.
PIT4907A
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
100864002B
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
PI0800A
This preliminary informational bulletin provides a procedure to reprogram the electronic power steering control module for comments regarding a indicator lamp illuminated and DTC C0544 and U0415 set.
PI0814A
This preliminary informational bulletin provides a procedure to install a revised generator, power steering gear inlet hose, evaporator hose to correct a steering wheel shudder during low speed manueuvers.
PIP4902F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4959C
This Preliminary Information communication provides information to the technician with information about vehicles that misfires or roughness on cold start up. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. If coolant is found in the cylinder technician will need to contact General Motors Product Quality Center for engine replacement.
PI0855
This preliminary informational bulletin provides a procedure to reprogram the navigation radio with the latest calibrations to correct a condition of th Navigation system being inopperative when using voice recognition to enter addresses.
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIC5491A
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIP4902E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
S8-10-08-44-004C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-PIE-0238
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4902D
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
PI0839
This preliminary informational bulletin provides information regarding a condition of the charging system light is illuminated and/or the Service Battery Charging System message is displayed, that might have been caused by oil being spilled into the generator while filling the engine oil level.
PI0086D
This preliminary informational bulletin provides a list of corrections for multiple concerns regarding Unexpected Loss of Radio Audio (Radio Goes Silent/No Sound) and Other Blackberry Phone - Bluetooth Issues
09-06-04-026E
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2
09-07-30-018C
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
12-00-89-007
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
PI0373A
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
PIT3237F
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
PIC5722A
This Preliminary Information communication provides information to the technician about customers that may comment of no map DVD, Compact Flash Card, or SD card supplied with the vehicle. Dealer should advise the customer that the map data is stored internal to the radio.
PIC5759
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
11-00-89-005B
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
07-00-89-037E
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM.
10-00-89-017V
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PI0828
This preliminary informational bulletin provides information on the guidelines and inspections for repair for dust intrusion into the passenger compartment
090730018C
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
PIT4931C
A Door May Not Open With The Outside Handle And/Or The Inside Handle.
PIT4995A
Rear Wiper and/or Front Rain Sense Wipers.
PIT4995B
Rear Wiper and/or Front Rain Sense Wipers.
PIT5076C
Learning Issues When Repairing Service Stability/Traction Message.
PI0745B
Information on Diagnosing Intermittent Electrical Concerns with Components Fused Through Instrument Panel Fuse Block.
PI0767A
Erratic or Insufficient Cooling when A/C Compressor is On
PI0814
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5598H
Guidelines For NJ1 Power Steering Powerpack
PIC5731
Date Displayed On The Radio Is One Day Ahead
PIT4911S
Navigation Radio Radio And Integrated Center Stack
PIT5176
Intermittent Hood Ajar Message.
SB-PIC-5731
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PC355B
ACDelco Return Parts Application
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.