PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5099J
PI to help diagnose A/C concern
PIP6113
This document provides the technician with a diagnostic tip if the vehicle stalls and set diagnostic trouble code P0191 and may also set P0172. The diagnostic tip has the technician inspect the high pressure fuel pump body markings to confirm it is an original manufacture part. If it is not an original manufacture part, they should install one and evaluate the vehicle.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIT6180A
This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
PIP4964F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
15-NA-010
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
25-NA-100
This warranty administration bulletin provides policy information on vehicles outside of a California Emissions State who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
13-02-32-001H
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
25-NA-065
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIT5994A
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
05-03-07-009L
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
11-00-89-005Y
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-08-51-001L
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
22-NA-244
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
01-08-42-001Q
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5696H
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT6261
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
24-NA-223
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PIP5621E
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
99-00-89-019Z
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
23-NA-154
This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIT5195H
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
21-NA-280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
24-NA-147
This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
18-NA-115
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
23-NA-125
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME) FAQs.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
22-NA-240
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
21-NA-147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminatedâ.
19-NA-256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States.
PIP4964E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
17-NA-281
This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope.
PIP5621D
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
01-08-42-001P
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIT5994
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
N192266181-01
Special Coverage. On certain 2010-2012 model year and 2016-2017 model year Chevrolet Equinox and GMC Terrain vehicles, the ball joints in the front windshield wiper modules of these vehicles may experience high corrosion and wear that could result in the separation of one or more ball joints from their sockets during wiper operation. If a ball joint were to separate, one or both of the windshield wipers could become inoperative. Dealers are to inspect the front wiper assembly and replace the wiper linkages or module as necessary. The repairs will be made at no charge to the customer.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
PIC5611H
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
22-NA-257
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PIT5698C
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5621C
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
N192266180-01
Special Coverage. On some vehicles, a link ball socket in the front wiper transmission may separate. If this were to occur, the driver would experience a sudden loss of front wiper function. Dealers are to replace the front wiper transmission kit or module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
18-NA-358
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
04-00-89-015X
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
PIT5195G
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIT5696F
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC6450
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
090604026V
Information.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
22NA018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
990089019W
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
18NA067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
18NA073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
20NA110
This service bulletin provides service information for a DEF pump that is unable to build pressure after replacement.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
070316004D
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
000090002L
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
18NA358
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
21NA280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT4916K
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
19NA256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
20NA132
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698B
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
21NA152
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.
21NA147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
110089002E
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
070089037Q
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
PIP5621B
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
18NA201
This technical bulletin provides a procedure to seal the bedplate bolt #621 if found the cause of the oil leak.
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
21NA068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
PIP5247A
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. P0651 may also be set in the ECM with the P06DE. Technician must follow published Service Information diagnostics for P06DE. If diagnostics lead to removing the oil pan or engine oil pressure is below specification when hot, to inspect the oil piston nozzles for damage. Technician should replace the broken oil nozzle(s) as long as the engine does not have any damage which warrants engine replacement.
PIP5803
This Preliminary information communicates to technician's if they remove the front timing cover when perprming a repair, they should inspect the timing chain guide upper bolt for being loose. This document is an attempt to collect parts so engineering can investigate the concern.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
070089036J
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIT5696E
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
010601011L
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
090604026S
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
040089015V
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
16NA019
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIC6208E
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
060089026Q
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
18NA115
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
990089019U
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
PIT4916J
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIP5180C
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
20NA128
This technical bulletin provides a procedure to replace the fuel filter drain or assembly if found the cause of the customers complaint.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698A
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
150089002B
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
PIP5095G
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5528F
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
PIP5740
This Preliminary information communicates to the dealer an issue where a customer may have incorrectly received a notification advising of a starting syetem issue with their veihcle. Dealer advised to inspect for a legitimate issue, if one found, diagnose accordingly.
990089019T
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
PIP5528E
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
20NA118
This technical bulletin advises that the code may be false and it should be cleared and then take the vehicle for a test drive to verify the code will not return and advise the customer of how the code may set during certain driving conditions.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
070604025M
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
20NA098
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
090089002R
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5195F
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
PIP4783B
This Prelimary information informs the dealer of a diagnotic trouble code that may set due to a failed high pressure fuel pump. Dealers are to check fuel pressure as per current testing outlined in GM service information and replace the fuel pump if needed.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
PIT5696D
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
N192273630-02
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year diesel engine vehicles. The engine control module (ECM) in these vehicles may not adequately diagnose or illuminate the malfunction indicator lamp (Check Engine Light) when frequent regeneration of the diesel particulate filter (DPF) occurs. Dealers are to program the engine control module (ECM) with corrected software.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
18NA072
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
060089026P
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
990089019S
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
040089015U
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
050307009J
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
150089005C
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
20NA029
This technical bulletin provides a Service Procedure to correct a Condition of Ticking, Tap or Rattle Noise from Engine.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
110089002D
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
15NA010
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT5696C
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
N192266180
N192266180 - Special Coverage - On some 2010-2012, and 2014-2017 model year Chevrolet Equinox and GMC Terrain vehicles, a link ball socket in the wiper transmission may separate. If this were to occur, the driver would experience a sudden loss of wiper function. Dealers are to replace the front wiper module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
PI0592F
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5621A
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
19NA259
This technical bulletin provides repair information to correct a customer concern of HVAC Pop Up on Infotainment Screen Blank, Displays Red Box, or Has Incomplete Information After Initial Start Up.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIT5699A
This preliminary information was released to point out a potential issue with a lack of A/C cooling due to an evaporator freeze up concern .
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP4670H
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP5676A
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP5676
This Preliminary information communicates to the technician information on what may be setting DTC P06DE. This is in addition to what is already in the service manual.
PIP5528D
This Preliminary information communicates the repair recommendations for misfire in HFV6 re-manufactured engines.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
18NA061
This technical bulletin provides a procedure on diagnosing and repair moisture/ice and possibly contamination/debris in the SAI system and how to clean it out.
19NA196
This diagnostic tip advises the tech to check if the upstream O2 sensor has been replaced with a faulty or aftermarket sensor and how to verify if the sensor is the cause of the concern.
PI0592E
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
090604026R
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
130089008B
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PIT5699
This preliminary information was released to point out a potential issue with a lack of A/C cooling due to an evaporator freeze up concern .
PIT5698
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIC6208D
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5528C
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIT4916H
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIP4964D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
18NA246
This technical bulletin provides a procedure to change the oil if excessive fuel has been found in the oil and the cause of the DTC set. Also replacing the PCV valve in camshaft cover and updating the ECM with latest software.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
PIP5549A
This Preliminary information communicates a diagnostic trail to a likely conclusion for lean codes on these vehicles.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5331H
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
PIT5205B
This Preliminary Information communication provides information to the technician about vehicles that have a blower speed knob only goes to 8 with less than expected high blower speed air flow. Technician should not replace any parts for this concern. Dealer should advise the customer to turn the ECO button Off and On at different blower speed settings 6 through 8 and note the change in the audible sound and air flow. This is a new enhancement to improve fuel economy when the ECO button is turned on.
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIT4916G
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIC6360
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
19NA065
This technical bulletin provides a procedure to replace the Aux fuel pump if found the cause of the customers concern.
PIP5122G
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
PIT5195E
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PIP5528B
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIP4670F
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004Y
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
PIT5402A
This Preliminary Information communication provides information to the technician for a forward collision alert or lane departure warning inoperative with no diagnostic trouble codes stored. This concern could be caused by an aftermarket windshield. Verify there is the General Motors logo in the lower right corner of the windshield.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5331G
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT5559A
This Preliminary Information communication provides information to the technician about vehicles that have a radio display were the HVAC Pop Up on the infotainment screen is blank, displays a red box, or contains incomplete information. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT4945H
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5302B
This Preliminary Information communication provides information to the technician about vehicles that may have turn signal indicators on the Instrument Panel Cluster do not match the audible warnings. Technician will need to test the battery using the GR8. Technician should also verify the charging system is operating correctly.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010310003R
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
120601003C
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying RTV Sealant.
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
PIT5444D
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5624
This Preliminary information communicates to the dealer an issue where the vehicle's engine may stumble and/or stall at startup. The dealer is to evaluate for a faulty aftermarket or incorrect upstream oxygen sensor.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
030603004X
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
18NA335
This informational bulletin provides to the technician the correct parts and the labor operation number in conjunction with the repair.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17NA066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
000310003X
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5427B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
PIT5625A
This preliminary information is to alert the service technician of a potential A/C evaporator freezing concern , engineering is investigating.
PIE0475A
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
PIP5601
This Preliminary information communicates
PIT4945G
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP3423P
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP5095F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5611G
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIT5625
This preliminary information is to alert the service technician of a potential A/C evaporator freezing concern , engineering is investigating.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP4495F
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5373B
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5569
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
18NA141
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
150603002M
This bulletin provides information on approved warranty part numbers for original equipment batteries.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
18NA125
This informational bulletin provides information for engine oil life monitor operation calculation.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
150603002L
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIC5611F
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5195D
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
010310003Q
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
110089002C
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIP5122F
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
16NA004
This technical bulletin provides a possible location and repair to a wiring harness that may be contacting the fuel pump cover.
PIP5095E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5331F
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PIP5180B
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIP4670E
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
150603002K
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIP5385D
This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes. New revision adds model year and removes the customer surveys.
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
18NA027
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5549
This Preliminary information communicates a diagnostic trail to a likely conclusion for lean codes on these vehicles.
PIP5331E
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100864002D
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
17NA348
This informational bulletin advises the new way required to tow a vehicle when using a dinghy or flat towing.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
PIE0433A
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 Fuel Trim System Lean Bank 2.
16NA214
This technical bulletin provides repair information to correct a condition of a left front drive shaft fluid leak.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP3535C
This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT5354B
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
16NA075
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
130232001E
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
PIP4959G
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
150603002J
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
16NA239
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
17NA386
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
150603002I
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
17NA344
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
PI1149A
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
17NA142
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
PIT5119F
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
17NA297
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
17NA334
This informational bulletin explains a normal condition caused by exhaust soot blowing by the VGT pivot seal.
PIE0399A
This engineering information bulletin ends the need for information from the field on vehicles that have the condition of Front Windshield Wipers Inoperative.
17NA331
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
PIC5650C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PI1043D
This preliminary informational bulletin adds the 2017 model year to information to correct a customer concern on opening hood when hood primary latch release cable is inoperative.
16NA249
Low Audible Whine Noise has been found to be transmitting from the balance shaft drive chain.
PI1067B
This preliminary informational bulletin adds the 2017 model year to repair information for a customer concern of Malfunction Indicator Lamp (MIL) on, Reduced Power Mode on, DTC(s) set, and/or poor performance/shifts.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP4495E
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
070849020M
IPC Odometer Programming Method Quick Reference Guide
140089004D
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
150603002H
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
16-NA-175
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
16-NA-249
LOW AUDIBLE WHINE NOISE FROM ENGINE
PI-1043D
Information on Opening Hood When Hood Primary Latch Release Cable is Inoperative Some customers or dealer personnel may comment that the inside hood release cable is not functioning and they are unable to open the hood.
PI-1067B
Malfunction Indicator Lamp (MIL) Light On, Reduced Power Mode, DTC Set, Poor Performance/Shifts In rare cases, some customers may comment that the malfunction indicator lamp is on, poor performance and reduced power mode on. Technicians may find DTC P0641 or various others set. Not all of the effects listed may be experienced. However, the different effects and driver notifications may be caused by one of the wires in the ECM harness being chafed or cut. Due to the cause of the condition, and the positions of the wires in the harness, it is unlikely that more than one circuit will be affected by the condition. This condition may be caused by the ECM wiring harness rubbing on the ECM bracket. The harness may have chafing or damage to the wires. Contact with the edge of the bracket may result in a rub-through of the wires within that harness.
PIE-0399A
Engineering Information Front Windshield Wipers Inoperative
PIE-0433A
Engineering Information Malfunction Indicator Lamp (MIL) On, DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 Fuel Trim System Lean Bank 2
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
17NA307
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being installed in the reman engines.
PIE0433
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Engineering Information ? Malfunction Indicator Lamp (MIL) On DTCs P0171 Fuel Trim System Lean Bank 1 and/or P0174 Fuel Trim System Lean Bank 2.
17NA281
This informational bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP3535B
This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
000601012H
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
150603002G
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIC6185A
This Preliminary Information communication provides information to the technician with a diagnostic tip for navigation radios that have inaccurate entries at times when using the voice recognition to input the address. When using the Navigation command "Address" or "Destination" this Allows an address to be stated as a one-shot method. When using the Navigation command "Directed Address" this Allows an address to be stated one step at a time. Directed address option may be a better choice for entering that address.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PIP4959F
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
03-08-46-004T
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
17-NA-211
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical connections that may set a DTC instead of just replacing a part.
PIT5119E
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIT5119E (1)
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
17-NA-242
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
PIT5444C
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
17-NA-237
This technical bulletin provides a procedure to replace the HVAC drain hose due to clogging causing a water leak within the vehicle.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
PI1385A
This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are installed on the vehicle.
PIP5507B
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
17-NA-230
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided.
PIC5611E
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
17-NA-223
This technical bulletin provides a procedure to replace the front speed sensor to correct the ABS and stabilitrak light on.
PIP5507A
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIP5507
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC6287
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5216F
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIC6283
This Preliminary Information communication provides information to the technician about vehicles that when watching a movie the audio does not match the video when playing though the vehicles speakers. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
17-NA-142
This informational bulletin provides information on Wireless Charging Module Diagnosis.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
16-NA-355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
17-NA-111
This technical bulletin advises to replace the radio if it blanks out and loses audio at times.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
PIP5389D
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P015A set. Dealers are directed to review Technical Service Bulletin17-NA-086 for repair information.
03-06-03-004U
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
15-06-03-002F
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIT5558
This Preliminary Information communication provides information to the technician about vehicles that have a faint beep noise in the background during Bluetooth phone conversations but everything sounds normal to the person inside of the vehicle. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5559
This Preliminary Information communication provides information to the technician about vehicles that have a radio display were the HVAC Pop Up on the infotainment screen is blank, displays a red box, or contains incomplete information. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
17-NA-099
This bulletin provides a procedure to replace the crankshaft balancer if found the cause of the customers concerns of noises or sparks.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
16-NA-007
This technical bulletin provides a procedure for reprogramming power steering control module due to a notchy or stick/slip feeling in the steering wheel near the center position.
17-NA-084
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
17-NA-086
This technical bulletin provides a procedure to reprogram the ECM to correct the MIL.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
PIE0399
This engineering information bulletin is requesting information from the field on vehicles that have the condition of Front Windshield Wipers Inoperative.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
10-00-89-006F
This informational bulletin provides information for dealers how to submit a product information report.
12-09-41-002D
This informational bulletin explains not to put anything metal or conductive on the passenger seat or it may set the reminder chime off.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4990D
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5095D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
17-NA-047
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5959C
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
02-00-89-002Q
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
PIP5331D
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 model year.
01-03-10-003O
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
07-06-04-025L
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
15-00-90-002A
This informational bulletin provides information on Installing the Correct Replacement Spin-On Oil Filter When Servicing.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP4902J
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5385C
This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes.
15-06-03-002E
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIP5180A
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
99-00-89-019O
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
PIT4915E
This Preliminary Information communication advises the technician that vehicles built with Regular Production Option Code (UW6) the subwoofer is only used for the Active Noise Cancellation.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIT5411G
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
99-00-89-019N
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
01-03-10-003N
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
02-00-89-002P
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIC6233
This Preliminary Information communication provides information to the technician about vehicles that when an incoming Bluetooth call will ring through the vehicle system, but the call can only be answered by using the handset. Technician can update the radio using the latest version of 15-NA-081 if the vehicle is 2014 or newer. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5354A
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
GCUS-3-760
16065 Service Update. Certain vehicles may have been assembled with a suspect gear set in the rear differential module (RDM). Specifically, the back face of the pinion gear in the RDM may have been cracked during the manufacturing process. If a crack propagates and a gear tooth fractures, it could wedge into the ring and pinion gear mesh interface and cause the rear wheels to lock up with the potential for loss of control of the vehicle. Dealers are to replace the rear differential module.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
16-NA-359
This technical bulletin provides a procedure to reprogram the ECM to the latest calibrations to correct the customers concern of the the MIL on with code P05CE set.
04-06-04-051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIP5122E
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
040604051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
150603002D
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
150603002C
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
16NA355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
PIP5413C
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P05CE stored. Clear code and test drive vehicle to ensure code does not return. If code is gone then release vehicle back to the customer or sales department. If code returns, follow SI service procedures to diagnose and correct concern.
030603004S
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
030603004T
Battery Testing and Warranty Replacement Requirements (North America ONLY)
040089015N
This warranty administration bulletin provide policy information on required operating procedures.
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
GCUS-3-711
16065 - Stop Delivery - Stop delivery of certain vehicles.
PIT4916F
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
PIT4995F
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5389C
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P015A set. After performing all published Service Information diagnostics for the Diagnostic Trouble Code and no resolution found, technician should check the engine oil level for being overfilled.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
07-00-89-037J
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
08-08-44-029G
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5282A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
PIP5413B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P05CE STORED. TECHNICIAN SHOULD REPLACE THE BANK 1 EXHAUST CAMSHAFT ACTUATOR.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
PIC5453B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. THE GENERAL MOTORS OF CANADA CUSTOMER CARE CENTRE IS THE SOLE AUTHORIZED PROVIDER OF A CERTIFICATION CONFIRMATION LETTER WHICH HELPS OUR CUSTOMERS IDENTIFY IF THEIR VEHICLES MEETS THE REQUIRED USA REGULATORY STANDARDS NECESSARY FOR IMPORTATION INTO THE USA.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
08-08-44-015G
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIP5244B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE POOR FUEL ECONOMY. DEALER SHOULD OBTAIN A DETAILED DESCRIPTION OF OUR CUSTOMERS DRIVING HABITS ON A DAILY BASIS, SUCH AS MILES DRIVEN, ROADS TAKEN, AND SPEEDS DRIVEN. TECHNICIAN SHOULD PERFORM AN INITIAL FUEL ECONOMY EVALUATION AND ACTUAL DRIVING EVALUATION.
01-00-89-010L
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
07-08-49-020K
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
01-03-10-003L
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
PIT5384B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.
PIC6073C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
PIC6208B
THIS PRELIMINARY INFORMATION COMMUNICATES THAT WHEN CUSTOMER OR TECHNICIAN MAY INDICATE WHEN ATTEMPTING TO ADD A NEW TRANSMITTER TO A VEHICLE FOLLOWING THE ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM PROCEDURE. THE PROCEDURE WILL NOT COMPLETE AND A MESSAGE "REMOTE LEARN PENDING" WILL BE DISPLAYED ON THE DRIVER INFORMATION CENTER. IN THE PAST TO PERFORM THE NEW TRANSMITTER PROCEDURE ONLY 1 PREVIOUSLY LEARNED TRANSMITTER WAS REQUIRED, THIS IS NO LONGER THE CASE NOW 2 PREVIOUSLY LEARNED TRANSMITTERS ARE REQUIRED AND PLACED INTO THE CUP HOLDER. IF THIS NEW PROCEDURE IS NOT FOLLOWED, THE "ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM" CANNOT BE PERFORMED. THE TECHNICIAN WILL BE FORCE TO ADD A TRANSMITTER USING SERVICE PROGRAMMING SYSTEM.
PIP5413A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABUT VEHICLES THAT MAY HAVE MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND P05CE SET. TECHNICIAN SHOULD CLEAR THE DIAGNOSTIC TROUBLE CODE WITH A SCAN TOOL AND TEST DRIVE TO ENSURE THE DIAGNOSTIC TROUBLE CODE DOES NOT RETURN.
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
PI1010A
THIS PRELIMINARY INFORMATIONAL BULLETIN ADDS 2015 - 2017 MY'S TO REPAIR INFORMATION FOR A CUSTOMER CONCERN OF ROUND DARK CIRCLES OF PAINT DISCOLORATION ON CENTER REAR AREA OF ROOF.
16NA043
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PIT5411F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
GCUS-3-657
60070 - Service Update. Vehicles have been built with front control arm mounting bolts which were produced with the wrong material, which may cause the lower control arm front bushing to separate from the cradle assembly. Dealers are to inspect the front cross member assembly lot code, and, if necessary, replace the nuts and bolts.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
16NA251
THIS INFORMATIONAL BULLETIN ADVISES THE DEALER THAT THE DIAGNOSTICS FOR PROACTIVE ALERTS ARE NOW PUBLISHED IN SERVICE INFORMATION AND THAT THE LABOR OPERATIONS FOR EACH PROACTIVE ALERT WILL ALSO TRANSITION INTO THE LABOR TIME GUIDE.
PIP5413
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABUT VEHICLES WITH A MALFUNCTION INDICATOR LAMP ON WITH LOW MILES. TECHNICIAN WILL FIND DIAGNOSTIC TROUBLE CODE P05CE STORED. TECHNICIAN SHOULD USE A SCAN TOOL TO CLEAR THE DIAGNOSTIC TROUBLE CODE AND TAKE THE VEHICLE FOR A TEST DRIVE TO ENSURE THE CODE DOES NOT RESET. IF THE DIAGNOSTIC TROUBLE CODE DOERS NOT RESET RELEASE THE VEHICLE. IF THE DIAGNOSTIC TROUBLE CODE RETURNS, FOLLOW THE PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5373A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
16NA246
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
16NA242
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
PI1259A
This informational bulletin explains the normal operation of the instrument panel automatic display brightness when the vehicle leaves a dark area.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
16-NA-214
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPLACE BOTH THE FRONT DRIVE SHAFT AND SEAL FOR VEHICLES WITH THE CONDITION OF A FLUID/TRANSMISSION FLUID LEAK FROM LEFT FRONT DRIVE SHAFT.
00-03-10-006M
THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT.
PIC5428G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. THE ELECTRONIC BRAKE CONTROL MODULE MAY HAVE ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES C0035-C0050 WITH SPECIFICALLY SYMPTOM 18, 5A, OR 0F. TECHNICIAN WILL GAIN ACCESS TO THE CORRECT WHEEL BEAR PER THE DIAGNOSTIC TROUBLE CODE THAT IS SET. IF DEBRIS IS FOUND ON THE MAGNETIC ENCODER RING IT WILL NEEDED TO BE CLEANED.
PI1521B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE POWER STEERING FUSE FOR A CONDITION OF LOSS OF POWER STEERING ASSIST AND/OR SERVICE POWER STEERING MESSAGE DISPLAYED.
PI0828C
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR APPLYING 2 WAY TAPE AND SPLASH GUARDS TO CORRECT A CONDITION OF DUST INTRUSION INTO THE PASSENGER COMPARTMENT.
PI1358B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO INSTALL RETAINERS TO THE CARPET TO CORRECT A CONDITION OF THE CARPET PULLING LOOSE FROM UNDER DRIVER SIDE BODY HINGE PILLAR TRIM PANEL .
PI1090B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR APPLYING SEAM SEALER TO THE OUTER FLOOR PANELS TO CORRECT A CONCERN REGARDING A WET FLOOR OR CARPET.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIP5277B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE A RESONANCE TYPE VIBRATION OCCURS BETWEEN 40 TO 60 MPH. IN MOST CASES THE ENGINE MUST BE UNDER A SLIGHT LOAD SUCH AS A/C COMPRESSOR ENGAGEMENT, LIGHT THROTTLE, AND IN 6TH GEAR TORQUE CONVERTER CLUTCH APPLIED. TECHNICIAN WILL RELAX THE ENGINE AND TRANSMISSION MOUNTS, THEN THE EXHAUST SYSTEM BY LOOSENING THE FRONT PIPE STUDS. ALSO WORK DOWN THE SYSTEM DISCONNECTING ONE EXHAUST HANGER AT A TIME. THEN TAKE THE VEHICLE ON A TEST DRIVE TO VERIFY THERE WAS IMPROVEMENT. IF ADDITIONAL STEPS ARE REQUIRED PLACE TWO SETS OF EXHAUST DAMPENERS ONE SET BEFORE AND ONE SET AFTER THE FRONT CATALYTIC CONVERTER. IT MAY BE REQUIRED TO MOVE THE PAIR OF DAMPENERS ALONG THE EXHAUST SYSTEM TO GET THE BEST RESULTS.
PI1023D
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION REGARDING THAT THE FLOOR FILLER TRIM PANEL WILL NO LONGER BE STANDARD EQUIPMENT.
09-06-04-026M
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
99-08-51-007G
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
10-00-89-005F
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
12-08-132-001D
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.
16-NA-146
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT ALL FOUR OF THE LIFT GATE MOUNTING BRACKETS AND REPLACE BRACKETS IF NECESSARY TO CORRECT A CUSTOMER CONCERN THAT AFTER OPENING THE POWER LIFT GATE, IT WILL NOT STAY IN THE FULL OPEN POSITION AND MAY DRIFT DOWN A FEW INCHES BEFORE COMING TO A REST CAUSED BY TO AN INCORRECT BALL STUD STRUT BRACKET BEING INSTALLED DURING ASSEMBLY.
PI1223B
This informational bulletin provides information on black smoke and rough idle on cold start.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
00-03-10-002J
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.
PI0360F
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications
08-00-89-014B
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics
07-00-89-037I
This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs
16-NA-069
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
03-00-89-006M
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores
03-06-03-004O
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)
06-00-89-029M
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
09-00-89-002M
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
04-00-89-015K
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
16-NA-055
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
16-NA-011
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.