PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC6551C
This Preliminary information communicates to dealer to perform a MEC reset for wireless projection issues
PIT5099J
PI to help diagnose A/C concern
PIT5966F
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message.
PIT6519
This preliminary information is to inform technicians and customers that the voice command will be inoperative when trying to open applications. Engineering is investigating and this PI will be converted to a bulletin when a repair is available.
PIC6423A
Pi created to provide GM dealers with information on gathering information for projection issue
PIC6551B
This Preliminary information communicates to dealer to perform a MEC reset for wireless projection issues
PIC6626A
PI created to guide technicians through radio restriction process
PIT5812G
This preliminary information announces the end of an engineering investigation into a brake pad noise.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIT5992B
This preliminary information discusses a condition that may arise from the drivers window switch sending an errant message causing the vehicle to enter manual fob learn mode.
N25-250552
Improvements to OnStar functionality.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIT6425D
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC'ss
N252516900-01
Emission Recall. General Motors has decided to conduct a Voluntary Emission Recall. Certain vehicles listed above may have a condition which can cause the fuel pump power control module to fail. If this were to occur, fuel flow to the engine could be interrupted. Dealers will replace the fuel pump power control module.
N252516900
Emission Recall. Additional VINs moved to Open status.
PIT5812F
This preliminary information announces the end of an engineering investigation into a brake pad noise.
PIC6626
PI created to guide technicians through radio restriction process
PIT6425C
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
PIP6098
This PI advised dealer technicians of possible causes of diesel fuel contamination in gasoline powered vehicles and advises of warranty direction.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIT6425B
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
PIT6425A
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
PIC6551A
This Preliminary information communicates to dealer to perform a MEC reset for wireless projection issues
PIT6440
The Driver Information Center may display a message of Transport Mode On after the ignition is cycled.
13598
New Vehicle Monitoring Programs Section in IVH
PIT5578E
This preliminary information advises technicians the heater hose clamps are one time use only.
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT6059C
This Preliminary information communicates an issue with super cruise unavailable due to the driver's monitoring camera and dealers to replace the camera.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIP5601B
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
PIP5601C
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
N252494770-01
Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the affected vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.
N252494770
Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the applicable vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.
PIT6180A
This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
PIT5966E
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
25-NA-118
This service bulletin provides information for the technicians to use a Customer Concern Verification sheet to facilitate the questions needing to be answered by the customer regarding Automatic Emergency Braking (AEB) issues.
15-NA-010
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
25-NA-100
This warranty administration bulletin provides policy information on vehicles outside of a California Emissions State who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
24-NA-139
This service bulletin provides a procedure to replace the FPDCM if found to cause customers concerns of Crank No Start, Stalling, Malfunction Indicator Lamp (MIL) Illuminated – DTC P023F or P129F Set.
PIT5551R
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
24-NA-229
This bulletin provides a procedure on how to check for a battery drain utilizing the Picoscope and how to measure the load on the system that may be causing a drain.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
25-NA-065
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
23-NA-164
This service bulletin provides repair information to correct a customer concern of Vehicle Will Lock and Unlock (Active Functions Work) but Will Not Crank or Start (Loss of Passive Functions Do Not Work).
23-NA-163
This service bulletin provides repair information to correct a customer concern of No Crank, No Start, Quick Start/Stall, No FOB Detected, Key FOBs Inoperative, B3924 00, B3925 00, B3926 00, B3927 00, B3928 00 Set.
23-NA-165
This service bulletin provides repair information to correct a customer concern of Vehicle Will Not Lock and Unlock (Loss of Active Functions) Crank or Start (Loss of Passive Functions) with DTC P0513 Set.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIC6591A
This Preliminary information communicates to dealer to contact TAC for a specific display issue.
PIT5994A
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
05-03-07-009L
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
11-00-89-005Y
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-08-51-001L
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
PIT5551Q
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
PIT6328A
This Preliminary information communicates to dealership technicians to contact Techline support to data wipe the radio to clear the PIN.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
PIT6059B
This Preliminary information communicates an issue with super cruise unavailable due to the drivers monitoring camera and dealers to replace the camera.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
22-NA-244
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
PIT6328
This Preliminary information communicates to dealership technicians to contact Techline support to data wipe the radio to clear the PIN.
23-NA-064
This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships.
21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content.
01-08-42-001Q
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
PIC6591
This Preliminary information communicates to dealer to contact TAC for a specific display issue.
24-NA-239
This informational bulletin provides a guide on how to diagnose and test for vibrations utilizing the PicoScope.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
22-NA-038
This warranty bulletin provides information on Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
22-NA-053
This service bulletin provides information for dealers/technicians on Labor Operations for Limited Production Option (LPO) Calibrated Accessories.
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5696H
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
22-NA-238
This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
21-NA-181
This service bulletin provides 9th gear operation information to respond to customers that may comment on transmission shift operation.
18-NA-210
This technical bulletin provides a procedure to correct a customer concern of a High Pitch Whine Noise Coming from Front Instrument Panel (IP) Speakers.
23-NA-021
This service bulletin advises the tech that the rotational Clicking Noise Heard After Engine Shut Down may be normal characteristics of the vehicle.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5812E
This preliminary information addresses a brake noise concern engineering is investigating at this time.
21-NA-169
This service bulletin provides diagnostic information/procedures to aid the service technician in diagnosing 9T45/50/60 automatic transmissions with low mileage and DTCs current or history related to the control solenoids and valves.
PIC6486H
This Preliminary information communicates to dealer that GM is aware of the issue and is working on a resolution.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
24-NA-108
This service bulletin provides a procedure to correct radio software concerns.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PIP5621E
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
99-00-89-019Z
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
23-NA-154
This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).
24-NA-209
A new radio software update, version C157/C158, was released to service vehicles equipped with Infotainment system RPO IOR to correct conditions of radio software related issues.
PIT5551P
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIT5966D
This Preliminary information communicates an issue with an OTA pending message still displayed after an OTA event and how to reset/clear the message.
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP5964D
This Preliminary information communicates a vehicle may come to the dealer with a complaint of no start, stalling, rough idle, no acceleration, loss of power, erratic shifting, fuel gauge inoperative, MIL illuminated with various codes stored. Technicians are directed to replace the K111FPDCM if any of these conditions can be validated and code P023F or P129F is found.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIC6486G
This Preliminary information communicates the part ordering restriction of the 6.2L L87 engine.
PIT6181
This preliminary information discusses driver assist functions that may be disabled due to incorrect tire size.
PIC6486F
This Preliminary information communicates to dealer that GM is aware of the issue and is working on a resolution.
PIC6551
This Preliminary information communicates to dealer to perform a MEC reset for wireless projection issues
PIT5195H
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
PIT6170
This Preliminary information communicates a no crank issue caused by a loose ground at G100.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
21-NA-268
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated or Possible Increased Brake Pedal Effort.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
18-NA-020
This technical bulletin provides a procedure to replace the charge air cooler due to moisture getting inside of it and causing a malfunction indicator lamp illuminated with DTC P0300 and/or P0299/P2227.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
23-NA-125
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME) FAQs.
21-NA-054
This service bulletin provides repair information to correct various functional concerns of the Instrument Cluster and DTC U0155.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
24-NA-060
This service bulletin provides repair information to correct a customer concerns of Radio Software issues.
17-NA-106
This technical bulletin provides repair information to correct a customer concern of an interior boom noise heard while driving low speeds in high gear.
24-NA-054
This service bulletin provides information on No Heated Seats or Heated Steering Wheel During Remote Start.
PIE0773B
This engineering information (EI) closure ends the need for gathering further information from technicians in regard to Melted Burn Marks and/or Smoke Smell Coming from the Height Adjuster Motor Under the Front Row Seat.
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
23-NA-055
This service bulletin provides information on the EL-52800 Diagnostic & Charge Battery Station (DCBS) â FAQs.
21-NA-122
This technical bulletin provides a procedure to replace the radiator brackets if found loose to correct a customer concern of excessive vibration in the steering wheel or seat or floor at idle or at low to moderate speeds.
23-NA-189
This service bulletin assists technicians in setting up PicoScope hardware/software to monitor CAN bus traffic (voltage patterns) to aid Technical Assistance (TAC) and Field Service Engineers (FSEs) in diagnosing electrical issues present on network communication circuits.
18-NA-035
This service bulletin provides information on a normal characteristic of a transmission that will not shift into overdrive range during cold ambient temperatures.
22-NA-166
This technical bulletin provides repair information to correct a customer concern of finding a water leak inside the interior of the vehicle.
23-NA-046
This service bulletin provides a procedure to check for water intrusion at the door electrical connectors and repair the wiring if found the cause of customer concerns of Power Windows and/or Mirrors Inoperative, Power Seat Movement Inoperative and/or Moving On Its Own, Side Object Detection Inoperative and/or Unwanted Activation, Power Door Lock Cycle Inoperative, Keyless Entry Inoperative.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
18-NA-162
This technical bulletin provides a procedure for air conditioning refrigerant desiccant replacement due to A/C Not Cooling or refrigerant loss.
18-NA-176
This technical bulletin provides a procedure to add reflective butyl tape to the rear driver's side module to correct the radar reflection being detected and triggering the false alerts.
PIE0773A
This engineering information (EI) s requesting information from technicians to perform the check list provided and contact the engineer listed in regard to Melted Burn Marks and/or Smoke Smell Coming from the Height Adjuster Motor Under the Front Row Seat.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
19-NA-181
This service bulletin provides a procedure to locate and repair the engine wiring harness to correct customer concerns of multiple electrical issues.
PIE0773
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regard to Melted Burn Marks and/or Smoke Smell Coming from the Height Adjuster Motor Under the Front Row Seat.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
22-NA-170
This bulletin offers Information on Possible Crank No Start or Extended Crank with DTC P12A6 or Service Safety Restraints message on DIC, with B0073.
17-NA-281
This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
22-NA-023
This service bulletin provides repair information to correct a customer concern of Instrument Cluster DIC Displays Programming in Progress Message and Progress Bar.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
23-NA-042
This service bulletin provides repair information to update radio software to correct customer concerns of Software related issues.
23-NA-108
This service bulletin provides repair information to dealers to Replace Video Processing Module (VPM) When Programming Fails.
21-NA-061
This service bulletin provides information for dealers on Using EL-52545 When Diagnosing PEPs Transmitter Key Fobs.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
23-NA-062
This service bulletin provides repair information to correct a customer concern of Rear View Camera Issues - DTCs B395A, B395B, B395C, B101E, B101D.
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
01-08-42-001P
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
N222381840-01
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the side blind zone alert feature is not functional on certain 2022 model year vehicles listed above, built beginning June 28, 2022. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to perform a configuration and setup on the instrument cluster, install side object sensing alert modules, and replace the outside rear view mirror glass.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
N222381840
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the side blind zone alert feature is not functional on certain 2022 model year vehicles listed above, built beginning June 28, 2022. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to perform a configuration and setup on the instrument cluster, install side object sensing alert modules, and replace the outside rear view mirror glass.
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
22-NA-235
This service bulletin provides repair information to correct a customer concern of Wireless Charging Intermittent When Using iPhone and Samsung Phones at Offset Positions.
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
23-NA-039
This technical bulletin provides a provides a procedure to replace the mirror caps for a condition of Outside Rearview Mirrors Incorrect Color.
23-NA-047
This informational bulletin provides information for dealers/technicians on Dust, Snow or Water Around Fuel Filler Area.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
N222377150
Service Update. Certain vehicles were built with body color external mirrors instead of high gloss black as part of the Midnight package. Dealers are to install the correct left and right outside rear view mirror housing upper covers.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
22-NA-045
This technical bulletin provides repair information to correct a customer concern of Air Conditioning Odor During Restart After Auto-Stop.
22-NA-127
This service bulletin provides repair information on release of Radio Software Version V160 Update to correct customer concerns of radio software issues.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
N222372590-02
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less).
19-NA-076
This service bulletin provides repair information to correct a customer concern of Blue or Black Screen and Service Rear Vision System Message on Radio Display Shifting into Reverse.
N212354520-06
Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module and heater and air conditioning user interface control. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 04O. Use IVH to verify if the vehicle is currently eligible in the Front Seat Cushion Vent Blowers Retrofit bulletin N222378560. If so, both retrofits should be performed at the same time.
N212354522-05
We are pleased to announce that additional 2022-2023 model year Buick Envision vehicles have been moved to Open status in IVH.
22-NA-115
This service bulletin provides information for U.S. dealers ONLY to refer to the Battery Maintenance Report to identify vehicles in dealer inventory that require attention.
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
20-NA-047
This service bulletin provides a service procedure to correct customer concerns of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set.
N212354520-05
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module and heater and air conditioning user interface control. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 04O. Use IVH to verify if the vehicle is currently eligible in the Front Seat Cushion Vent Blowers Retrofit bulletin N222378560. If so, both retrofits should be performed at the same time.
N222372590-01
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less). Dealers will install a TCV thermal wrap and, if applicable, reprogram the Engine Control Module.
22-NA-257
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
N222372590
Service Update. Certain vehicles listed above may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less). Dealers will install a TCV thermal wrap and, if applicable, reprogram the Engine Control Module.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
N212354520-04
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature.
PIE0730A
This engineering information (EI) closure ends the need for gathering information from technicians in regards to the malfunction indicator lamp (MIL) illuminated on driver information center (DIC), vehicle does not start and/or stalls, DTC P129F set.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
N212354520-03
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 04O. Use IVH to verify if the vehicle is currently eligible in the Front Seat Cushion Vent Blowers Retrofit bulletin N222378560. If so, both retrofits should be performed at the same time.
22-NA-250
This service bulletin provides repair information to correct a customer concern of Rear View Camera Display Gridlines Dim.
PIE0730
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to the malfunction indicator lamp (MIL) illuminated on driver information center (DIC), vehicle does not start and/or stalls, DTC P129F set.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
N212354520-02
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 04O. Use IVH to verify if the vehicle is currently eligible in the Front Seat Cushion Vent Blowers Retrofit bulletin N222378560. If so, both retrofits should be performed at the same time.
22-NA-224
This service bulletin provides a repair procedure to correct a customer concern of Reduced Engine Power, Malfunction Indicator Lamp (MIL) Illuminated - DTCs P0101, P0172, P0299, P0506, and/or P1101 Set.
N212354522-03
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front and rear seat heater control modules, reprogram the body control module and on some vehicles, reprogram the HVAC control module. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 04O. Use IVH to verify if the vehicle is currently eligible in the Front Seat Cushion Vent Blowers Retrofit bulletin N222378560. If so, both retrofits should be performed at the same time.
15-NA-087
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system.
22-NA-205
This service bulletin provides information on Module Harvesting.
PIE0703B
This engineering information (EI) closure ends the need for gathering information from the field in regards to Intermittent No Start But Vehicle Has Power.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
N212354520-01
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 040. DO NOT replace the Left or Right Front Seat Cushion Ventilation Blower at this time.
N212354522-01
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front and rear seat heater control modules, reprogram the body control module and on some vehicles, reprogram the HVAC control module. Note: Some vehicles may also require an additional retrofit of the Left and Right Front Seat Cushion Ventilation Blower in order to restore full functionality of the ventilated seats. Vehicles built with this condition can be identified by RPO 040. DO NOT replace the Left or Right Front Seat Cushion Ventilation Blower at this time.
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
N212354520
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022-2023 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front seat heater control module, reprogram the body control module and on some vehicles, reprogram the HVAC control module.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-177
This informational bulletin provides information for dealers/technicians on Intermittent or Inoperable Rearview Camera, May Display Blue or Black Screen With Error Message.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
19-NA-013
This technical bulletin provides repair information to correct a customer concern of hearing a ticking or popping noise at roof rail assist handle(s).
N222379030-01
Product Emission Recall - certain vehicles with a 1.5L (RPO LYX) engine. A small number of these vehicles may have been built with an incorrect catalytic converter. Dealers are to inspect the catalytic converter and replace it if the correct one was not originally installed.
N212354522
Customer Satisfaction Program. Due to the industry-wide semiconductor shortage, the front heated/ventilated seats, front heated seats, or rear heated seats are not functional on certain 2022 model year vehicles listed above, built beginning November 15, 2021. The affected vehicle owners should have been made aware of the condition at sale, and notified that once parts are available, they would be eligible for a no additional cost retrofit to enable the feature. Dealers are to replace the front and rear seat heater control modules, reprogram the body control module and on some vehicles, reprogram the HVAC control module.
22-NA-174
This service bulletin provides information on Terms and Conditions/Privacy Statement App (TCPS App) Guide for infotainment systems in a default factory demo mode.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIE0708B
This engineering information (EI Lite) ends the need for further information from the field in regards to having a intermittent and/or inoperable rear camera and blue or black screen may be present with error message present.
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
N222375370
Certain vehicles require the replacement of the left front seatbelt retractor as part of an internal investigation.
04-00-89-015X
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
22-NA-107
This service bulletin provides repair information to correct a customer concern of a Service AWD Message in DIC at Ignition On with DTC C056D Set.
N222376920
Cancellation of Stop Delivery Order for 2022MY GMC Terrain â N222376920 â Wheelhouse Liner Build Shy â 2022MY GMC TERRAIN VINS REMOVED
22-NA-138
This informational bulletin provides information for dealers/technicians on the appearance of the male buckle on the front seat belt retractor being different in side to side comparison.
22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
21-NA-188
This service bulletin provides service information/procedures on continuous improvement Radio Software Version V158 Update to address customer comments on software related issues.
PIE0708A
This engineering informational bulletin is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to having a intermittent and/or inoperable rear camera and blue or black screen may be present with error message present.
PIE0703A
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Intermittent No Start But Vehicle Has Power.
PIT5921
This Preliminary information communicates diagnostics aids for rear view camera issues that may be encountered.
PIE0703
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to Intermittent No Start But Vehicle Has Power.
20-NA-227
This service bulletin provides a procedure to correct a customer concern of a Wobble Vibration on Hard Acceleration.
21-NA-277
This service bulletin provides repair information to correct a customer concern of No Crank, No Start, Quick Start/Stall, Key Fobs Inoperative with DTCs B2924 00, B3925 00, B3926 00, B3927 00, or P0513 set.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
22-NA-065
This technical bulletin provides a procedure to install a CAC and a Grille Cover to correct the customers concern of a Malfunction Indicator Lamp Illuminated or Flashing - DTC P0300 Set When Driving In High Humidity Or In Heavy Rain.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
22-NA-050
This service bulletin provides information for dealers/technicians on Changes to Front Heated and/or Ventilated Seats, and Second Row Outboard Heated Seats for Certain 2022 Passenger Car, Crossover, SUV, and Truck Models Equipped with RPO 00V, 00R and/or RGJ produced without front Heated/Ventilated Seat Module and/or rear Heated Seat Module.
04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
05-00-89-072E
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
N222360940
Customer Satisfaction Program. On some vehicles with LPO AAK (Premium All-Weather Floor Liners), the purchased rear floor liner was not included in the vehicle. Dealers are to ask the customer if they want the rear all-weather floor liner installed in the rear seat location, taking the place of any existing mats, or placed in the rear cargo compartment for future use. If the rear all-weather floor liner takes the place of any existing mats, the existing mats will be placed in the rear cargo compartment.
22-NA-020
This warranty administration service bulletin provides warranty labor operation restriction information for dealers/technicians on Park Assist, Heated/Vented Seats, and/or Heated Steering Wheel Options and Features are Inoperative for vehicles that may have had options built without modules due to semiconductor shortage.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
060089029U
Information.
090604026V
Information.
18NA235
This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in performance in regards to the customers concerns.
18NA103
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
18NA361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part.
18NA150
This informational bulletin provides information on 6.6L Duramax Possible Oil Leak Path Information.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.