Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
M1684
Service Bulletin/Repair Instructions
SERVICE BULLETIN M1684: MARKET SPECIFIC BATTERY INTRODUCTION. PURPOSE: Initial Release. This bulletin informs dealers of the availability of new batteries for new Original Equipment (OE) vehicle production and in the Parts and Accessories (P&A) catalog. Availability of the new Absorbed Glass Mat (AGM) batteries will vary by market and will be transitioning over the next few months. NOTE: The ring terminal screws are not compatible between Leoch and East Penn batteries. The new batteries will include new ring terminal screws, which must be used. The ring terminal screws from the old battery need to be discarded.
M1555
Warranty Program/Extension
SERVICE BULLETIN M1555 (REV E): BATTERY WARRANTY GUIDELINES. PURPOSE: Revision E. Added: Added procedures for the DCA-8000 E Battery Tester.* Updated: All sections. This bulletin informs the dealership network that Harley-Davidson has provided guidelines for battery warranty.
M1490
Service Bulletin/Repair Instructions
SERVICE BULLETIN M1490 (V 24.8.8): DIGITAL TECHNICIAN II - UPDATES AND RELEASE NOTES. PURPOSE: This bulletin informs dealers that Harley-Davidson has made a software update to Digital Technician II (DT II). DIGITAL TECHNICIAN II (PART NUMBER: HD-48650). Version 24.8.8. Release Date: Week of August 5, 2024. New Features for Harley-Davidson vehicles: Advanced Module Replace for 2021 and later Revolution Max; 2023 and later CVO Touring; and 2024 Street Glide (FLHX), Road Glide (FLTRX). New Features for LiveWire vehicles: Updated calibrations for 2024 S2DM EV1/ EV6; 2024 S2MH EV1; and 2024 S2DM, S2MH. Changes: Added Hand Control Module (HCM) (Part No. 71500522A and 71500536A) for reflash support.
PAB1158
Service Bulletin/Repair Instructions
GENUINE MOTOR PARTS AND MOTOR ACCESSORIES BULLETIN PAB1158: OIL FILTER PACKAGING AND CASE QUANTITY UPDATE. PURPOSE: To inform dealerships that Harley-Davidson has made updates to oil filters including new part numbers, packaging design, and bulk case quantity changes.
PAB1146
Service Bulletin/Repair Instructions
GENUINE MOTOR PARTS AND MOTOR ACCESSORIES BULLETIN PAB1146: 68193-95 BULB WEDGE, FENDER TIP LAMP. Purpose: To inform dealers of an issue with the bulb wire terminals not being to specification. The light bulbs were used in numerous front and rear fender tip light assemblies for domestic and international applications.
PAB1144
Service Bulletin/Repair Instructions
GENUINE MOTOR PARTS AND MOTOR ACCESSORIES BULLETIN PAB1144: 2021-2022 SCREAMIN' EAGLE STAGE I (CARB) EO APPROVALS. PURPOSE: Revision. To inform California dealers about the new California Air Resources Board (CARB) approvals for select 2021-2022 Harley-Davidson vehicles. Summary: Various Screamin' Eagle Air Cleaner Kits and Stage I calibrations have been approved for sale on select 2021 and 2022 Harley-Davidson models. Please see the table below that indicates which part numbers should be ordered for what models. Revision: Refer to Summary. Update non-Bluetooth calibrations availability.
1HDM5V2A05
Service Bulletin/Repair Instructions
TECH ARTICLE TA0023: TA0023: Crankshaft Rod Bearing. Purpose: Technicians have been falsely identifying connecting rod bearings as failed due to a perception of resistance as the rods are rotated. The clearance of the Twin Cam and Milwaukee-Eight® crank pin bearings are maintained to a very tight range. This optimizes performance and maintains low mechanical noise in operation. The connecting rod bore can also distort slightly in operation due to stress relaxation. As a result, bearing clearance decreases due to the contact zone broadening and the load being distributed over more rollers. The combination of a bore being slightly out of round and reduced bearing clearance can result in varying degrees of resistance through the range of motion. Axial clearance is also tightly controlled for proper alignment. For these reasons, zones of resistance can be found when the connecting rods are rotated by hand through their range of motion. Resistance during rod motion, by itself, is not an indication of a performance or durability concern.
TT451
Service Bulletin/Repair Instructions
Noise from the cam chest area possibly accompanied by milky engine oil. Moisture can cause slight swelling in the tensioner causing it to stick in the housing. A vehicle that makes repeated short trips can have this condition because the engine does not reach normal operating temperatures, allowing condensation and moisture to build up in the engine oil.