167-T2406-1
Service Bulletin/Repair Instructions
After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
Vehicle report
2007 HINO NC6J
Service bulletins
40 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
167-T2406-2
Service Bulletin/Repair Instructions
This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
167-B0502-12
Service Bulletin/Repair Instructions
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-P1602-12
Service Bulletin/Repair Instructions
13-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified to make the below changes into a kit that consist of the correct parts when ordering the kit ID number. The below information illustrates the kit components per engine and date ranges.
167-T1514-12
Service Bulletin/Repair Instructions
TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards the driver side or passenger side. The following publication can be referenced to obtain the manufacture?s measurement positions and specifications. Should the truck not meet the specifications, you should consider the following potential causes noted in the inspection guideline section below.
167-B1523-12
Service Bulletin/Repair Instructions
SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a service part and should be used if replacement of the head gasket is necessary. Improvement of the head gasket includes the addition of rubber seals around the engine oil and engine coolant port holes.
167-B1312-12
Service Bulletin/Repair Instructions
SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
167-B1509-12
Service Bulletin/Repair Instructions
SB-15-009 This bulletin provides the corrective action for a fluid overflow condition from the main housing breather at startup in cold ambient temperatures at or below +5F (-15C).
167-B1415-12
Service Bulletin/Repair Instructions
SB-14-003 The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
167-B1307-12
Service Bulletin/Repair Instructions
13-008 Design Change of the Idler Gear Case and Idler Gear Bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idler gear case and bolt were changed to increase the robustness for the abnormal load. The details are as follows.
167-B0902-12
Service Bulletin/Repair Instructions
SB ? 09 - 002 This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be tested and replaced when necessary before replacing the supply pump assembly for a fuel pressure related concern.
LT-0010
Service Bulletin/Repair Instructions
Hino Quick Reference Guide 2005-2010 Model Years
SB-09-002
Service Bulletin/Repair Instructions
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary.
167-B0803-12
Service Bulletin/Repair Instructions
SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-P0805-12
Service Bulletin/Repair Instructions
PTB 08-08 2005-2008 Quick Reference Guide Correction to Page 60
167-P0802-12
Service Bulletin/Repair Instructions
PTB 03-08 Spring Assemblies.
167-P0803-12
Service Bulletin/Repair Instructions
PTB 01-08 Complete Engine Assembly Part Numbers
167-T0707-12
Service Bulletin/Repair Instructions
07 - 008 DX REPORT ? EXPORTING, SAVING AND PRINTING FROM PAST WORK INFORMATION
167-P0702-12
Service Bulletin/Repair Instructions
Revised Warranty Process ? Denso Fuel Pumps & Injector Nozzles Exchange Denso Fuel Pumps & Injector Nozzles. Effective immediately, fuel pumps and injector nozzles replaced under warranty are to be purchased from the Memphis PDC. It is no longer necessary to order warranty replacement pumps and nozzles from Denso.
167-T0706-12
Service Bulletin/Repair Instructions
07 - 006 VOLTAGE DROP TEST
167-P0701-12
Service Bulletin/Repair Instructions
Introduction of Exchange Turbocharger Program. Hino Trucks is pleased to announce the introduction of the Turbocharger Exchange Program for its 2005 ? 2008 Model Year trucks. Effective June 21, 2007, the following turbocharger part numbers will become new exchange products: 2005 ? 2008 Model Year trucks.
167-T0705-12
Service Bulletin/Repair Instructions
07 - 005 No Throttle Response (brake light switch)
167-T0704-12
Service Bulletin/Repair Instructions
07 - 004 ABS Wheel Sensor (active fault 3-1 thru 3-4)
167-T0703-12
Service Bulletin/Repair Instructions
07 - 003 ELECTRIC TRAILER BRAKE CONTROLLER APPLICATION
167-B0702-12
Service Bulletin/Repair Instructions
SB - 07 - 005 The document is to inform the dealers about the change in material and tightening torque of the rocker arm support bolts and camshaft bearing cap bolts.
167-T0708-12
Service Bulletin/Repair Instructions
06 - 012 SPEEDOMETER PULSE ADAPTER CONVERSION FORM
SB-07-003
Service Bulletin/Repair Instructions
This bulletin provides technical information on the redesigned axle breather that replaced the old (current) axle breather P/N A1199P1394.
07-001
Service Bulletin/Repair Instructions
This Tech Tip provides information concerning the updated torque specification found in the Hino Workshop Manual regarding the Arvin Meritor front non-drive steer axles MFS-06 and MFS-08
SB-07-002
Service Bulletin/Repair Instructions
This bulletin provides information concerning the updated torque specification found in the Hino Workshop Manual regarding the Arvin Meritor front non-drive steer axles MFS-06 and MFS-08
167-P0703-12
Service Bulletin/Repair Instructions
TB-001-07 Hino uses both Davco and Racor fuel/water separators on its vehicles. To determine the correct filter you must know which one is on the vehicle. The Davco is shown on the left. The Racor is shown on the right and has a primer button.
167-P0704-12
Service Bulletin/Repair Instructions
TB-04-07 An engineering change in connecting rods was made from a stud with nuts to fasten the cap, to a bolt only to fasten the cap. The connecting rods with the stud and nuts are no longer available. The two different styles are interchangeable however the bearings are not. The bearing ?tang? was relocated as well as a difference in the width.
06-011
Service Bulletin/Repair Instructions
Fuel diluting engine oil
167-T0605-12
Service Bulletin/Repair Instructions
06 - 010 LOW POWER (fuel restriction)
167-T0606-12
Service Bulletin/Repair Instructions
06-011 HIGH PRESSURE FUEL PUMP FRONT SEAL FAILURE
167-T0603-12
Service Bulletin/Repair Instructions
06 - 008 ABS EXTENSION HARNESS No throttle response on 2007 air brake chassis with automatic transmissions when selector placed in drive. No cruise control on 2007 air brake chassis with manual transmissions.
167-B0602-12
Service Bulletin/Repair Instructions
SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
167-B0601-12
Service Bulletin/Repair Instructions
SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retention of liquid gasket used during engine production. This changed the appearance of the engine oil cooler housing but does not affect function or applicability.
167-B0508-12
Service Bulletin/Repair Instructions
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0509-12
Service Bulletin/Repair Instructions
SB ? 05 - 006 Upon removal of a transmission assembly from the vehicle, inspection is required to confirm the presence and correct installation of the two dowel pins in the rear engine housing. In some rare cases one or both dowel pins may have come out with the transmission during removal. These pins need to be positioned in the engine housing prior to the installation of a replacement transmission assembly. If flex plate is broken, please confirm that the two dowel pins can be found either on the rear engine housing or on the transmission housing.
167-B0504-12
Service Bulletin/Repair Instructions
SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.