167-T2406-1
Service Bulletin/Repair Instructions
After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
Vehicle report
2017 HINO NE8J
Service bulletins
19 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
167-T2406-2
Service Bulletin/Repair Instructions
This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
167-R1701-11
Service Bulletin/Repair Instructions
The engine ECU (Engine Control Unit) on all 2016MY-2018MY trucks contained in dealer inventory need to be reprogrammed prior to delivery. Subject vehicles contain an error in the DEF monitoring program. To eliminate this situation, it is necessary to reprogram the engine ECU with improved software prior to sale of the vehicle.
167-T1702-05
Service Bulletin/Repair Instructions
TT-17-009 Beginning with 2017 model year, all Hino vehicles are equipped with a particulate matter (PM) sensor near the exhaust exit. A ceramic sensing element is used in the PM sensor and can be damaged or broken if the sensor is dropped or impact occurs to the head of the sensor. If removal or replacement of the PM sensor is necessary, care should be taken with both the old and new sensors to prevent any damage or additional damage to the sensor. For warranty consideration, the PM sensor MUST be returned in the original box and the plastic protective cap installed. 2017 and 2018 model year Conventional trucks and COE (Cab Over Engine) trucks.
167-B0502-12
Service Bulletin/Repair Instructions
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B1605-12
Service Bulletin/Repair Instructions
SB-16-012 In the event that a subject vehicle exhibits a (MIL) malfunction indicator lamp and a P0300 (All Injector Misfire) is stored in the engine ECU, enhanced ECU software is available to correct this concern.
167-B1621-12
Service Bulletin/Repair Instructions
SB-16-010 Correction of the inspection of the DPR filter.
167-B1503-12
Service Bulletin/Repair Instructions
SB-15-002 CORRECTION OF WORKSHOP MANUAL FOR 2013 - 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P2123)
167-B1504-12
Service Bulletin/Repair Instructions
SB-15-003 CORRECTION OF WORKSHOP MANUAL FOR HINO 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P0421)
SB-09-001
Service Bulletin/Repair Instructions
This bulletin provides diagnostic information for monitoring the engine running data to determine if the Suction Control Valve is defective, and a service procedure for replacing the Suction Control Valve when necessary. The SCV should be tested and replaced when necessary before replacing the supply pump assembly for a fuel pressure related concern.
167-B0803-12
Service Bulletin/Repair Instructions
SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-B0602-12
Service Bulletin/Repair Instructions
SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
167-B0601-12
Service Bulletin/Repair Instructions
SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retention of liquid gasket used during engine production. This changed the appearance of the engine oil cooler housing but does not affect function or applicability.
167-B0501-12
Service Bulletin/Repair Instructions
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0503-12
Service Bulletin/Repair Instructions
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) Resistance between terminals of the main relay should be 111 Ohms
167-B0505-12
Service Bulletin/Repair Instructions
SB ? 05 - 007 DESIGN CHANGE OF WATER PIPE FOR J08E
167-B0506-12
Service Bulletin/Repair Instructions
SB ? 05 - 008 This document is to inform the dealers about the addition of the pressure sensor cover and related part for the J08E engine.
167-B0508-12
Service Bulletin/Repair Instructions
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0504-12
Service Bulletin/Repair Instructions
SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.