167-T2406-1
Service Bulletin/Repair Instructions
After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
Vehicle report
2015 HINO NJ8J
Service bulletins
43 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
167-T2406-2
Service Bulletin/Repair Instructions
This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
167-B1904-01
Service Bulletin/Repair Instructions
SA-19-011 AACL0 CONVENTIONAL ALP DRUM AND DUST SHIELD PROCEDURE CHANGES
167-R1701-03
Service Bulletin/Repair Instructions
17MY vehicles contain the function to monitor PM sensor performance, however because the threshold for detection logic is not appropriate, the engine ECU may not detect a malfunction of the PM sensor. The following procedure provides direction for reprogramming the PM sensor. Certain 17MYCOE Trucks equipped with a J05 engine
167-T1701-03
Service Bulletin/Repair Instructions
Beginning with the 2017 model year, Hino changed the standard battery from a group 27 to a group 31. In the event that a group 27 battery must be replaced, it is recommended to use the group 31 as the service replacement for 2014MY and newer units. 2014MY-2016MY Hino Conventional trucks
167-B1426-12
Service Bulletin/Repair Instructions
SA-14-026 The broken hood grille procedure (SB-14-020) has been revised to reuse the grille nuts (SZ17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised procedure has been posted on HinoNet. Please see the picture below on which area of the procedure has been updated.
167-R1603-12
Service Bulletin/Repair Instructions
SCB-001-16 A subject vehicle may exhibit an illuminated check engine lamp with DTC (Diagnostic Trouble Code) P14BF ?EGR (Exhaust Gas Recirculation) Valve Controller Temperature Sensor 1, 2 Rationality. The EGR valve may falsely detect this rationality fault, causing the P14BF DTC to be set and stored in the engine ECU. Enhanced EGR valve software is available to prevent this false detection.
167-B0502-12
Service Bulletin/Repair Instructions
SB - 05 - 004 SPEEDOMETER RECALIBRATION. This document is to inform of the procedure to calibrate the Pulse Adjust Module whenneeded (ex. tire size change, rear carrier ratio change).
167-B1623-12
Service Bulletin/Repair Instructions
SB-16-019 An enhanced fuel cut valve is available to address a potential sticking condition that results in excess residual pressure in the dosing injector (7thinjector) supply pipe. A sticking fuel cut valve may result in the following DTC?s (diagnostic trouble codes) setting: 1. If DTC P0005 (fuel cut valve stuck closed) sets in the engine ECU, replace the fuel cut valve with the part number listed below. 2. If DTC P20DE (pressure sensor performance invalid) or DTC P20DF (pressure sensor signal too low) set in the engine ECU, this could be a result of the fuel cut valve sticking. Follow the workshop manual diagnostic procedure in section 4 of the Hino Workshop Manual (J08E Engine Control System) for the DTC. Also, inspect for signs of fuel contamination that could restrict the fuel filter or bubble separator filter. If no issues are identified with fuel contamination, and the workshop manual procedure does not identify a concern, replace the fuel cut valve with the part number listed below.
167-B1621-12
Service Bulletin/Repair Instructions
SB-16-010 Correction of the inspection of the DPR filter.
167-B1616-12
Service Bulletin/Repair Instructions
SB-16-004 1. In the event that a subject vehicle exhibits an illuminated check engine lamp and DTC?s P2201, P2214, P206B, P207F, or P20EE are stored in the DCU, the NOX sensor may have failed due to a cracked NOX sensor heating element. Follow the revised Workshop Manual diagnostic procedure to determine if the NOX sensor has failed. 2. Enhanced DCU software is available to prevent the NOX sensor heating element from cracking due to exposure of condensation on the heating element. 3. The enhanced DCU software will also prevent false detections of DTC P142A being set in the DCU.
167-B1528-12
Service Bulletin/Repair Instructions
SB-15-031 Foreign debris in the DEF (Diesel Exhaust Fluid) tank may cause the SCR (Selective Catalyst Reduction) system to malfunction. This can result in DTC?s (Diagnostic Trouble Codes) P20E8 or P20E9 - DEF Pressure Abnormality. An inlet strainer for the DEF tank has been made available to prevent foreign material from entering the DEF tank.
167-B1527-12
Service Bulletin/Repair Instructions
SB-15-030 On subject vehicles, the MIL (Malfunction Indicator Lamp) may illuminate with DTC (Diagnostic Trouble Code) U02A2 stored in the engine ECU. This may be due to a malfunction of the DEF (Diesel Exhaust Fluid) tank sensor assembly. Perform the diagnostic procedure for DTC U02A2 as outlined by the Workshop Manual (DEF SCR System Section for Conventional Vehicles, Engine Troubleshooting Section for COE Vehicles). If the diagnostic procedure leads to DEF tank sensor replacement, a more robust DEF tank sensor has been made available.
167-T1514-12
Service Bulletin/Repair Instructions
TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards the driver side or passenger side. The following publication can be referenced to obtain the manufacture?s measurement positions and specifications. Should the truck not meet the specifications, you should consider the following potential causes noted in the inspection guideline section below.
167-B1523-12
Service Bulletin/Repair Instructions
SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a service part and should be used if replacement of the head gasket is necessary. Improvement of the head gasket includes the addition of rubber seals around the engine oil and engine coolant port holes.
167-T1513-12
Service Bulletin/Repair Instructions
TT-15-014 The transmission DTC?s P0974 and P0986, may be found on 12MY-15MY COE models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case and the battery post.
167-B1312-12
Service Bulletin/Repair Instructions
SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
167-B1515-12
Service Bulletin/Repair Instructions
SB-15-016 New parts are available to prevent repeat exhaust manifold stud failures on the J05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
167-B1511-12
Service Bulletin/Repair Instructions
SB-15-011 The following TSB (Technical Service Bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
167-B1510-12
Service Bulletin/Repair Instructions
SB-15-010 Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated EGR valve has been made available to prevent this occurrence.
167-B1503-12
Service Bulletin/Repair Instructions
SB-15-002 CORRECTION OF WORKSHOP MANUAL FOR 2013 - 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P2123)
167-B1504-12
Service Bulletin/Repair Instructions
SB-15-003 CORRECTION OF WORKSHOP MANUAL FOR HINO 2015MY (REVISION OF TROUBLESHOOTING PROCEDURE FOR THE DTC P0421)
PA-2014-073
Service Bulletin/Repair Instructions
2015 All-Makes Marketing and Advertising Support Package
TT-14-033
Service Bulletin/Repair Instructions
When replacing an engine block with service part no., 11401E0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 oil passage plugs, you will need to install them before proceeding
SB-14-020
Service Bulletin/Repair Instructions
When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
167-B1418-12
Service Bulletin/Repair Instructions
SB-14-012 A subject vehicle may exhibit an illuminated check engine lamp with DTC (Diagnostic Trouble Code) P0421 (Catalyst efficiency below threshold). The engine ECU may falsely detect an issue with the ATC (After Turbo Catalyst) with the current ECU software. If DTC P0421 is stored in the engine ECU, reprogram the ECU to the latest software level prior to suspecting a fault with the ATC.
SB-14-012
Service Bulletin/Repair Instructions
A subject vehicle may exhibit an illuminated check engine lamp with DTC (Diagnostic Trouble Code) P0421 (Catalyst efficiency below threshold). The engine ECU may falsely detect an issue with the ATC (After Turbo Catalyst) with the current ECU software. If DTC P0421 is stored in the engine ECU, reprogram the ECU to the latest software level prior to suspecting a fault with the ATC.
167-R1407-12
Service Bulletin/Repair Instructions
T0280 During installation of the air pressure sensors on the air tanks, it is possible that they could have been damaged causing incorrect air pressure readings.
TT-14-017
Service Bulletin/Repair Instructions
Bendix® Air Dryer Service
167-B1423-12
Service Bulletin/Repair Instructions
SB-14-005 2011MY-2015MY Conventional Keyless Entry Programming
SB-15-010
Service Bulletin/Repair Instructions
Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the EGR (Exhaust Gas Recirculation) butterfly plate with a repeat P1604 DTC (Diagnostic Trouble Code) stored in the engine ECU. A heated EGR valve has been made available to prevent this occurrence. Hino Conventional NE8J, NJ8J and NV8J trucks built before 10/15/2014
167-B1307-12
Service Bulletin/Repair Instructions
13-008 Design Change of the Idler Gear Case and Idler Gear Bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idler gear case and bolt were changed to increase the robustness for the abnormal load. The details are as follows.
167-B0803-12
Service Bulletin/Repair Instructions
SB - 08 - 005 This document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
167-T0706-12
Service Bulletin/Repair Instructions
07 - 006 VOLTAGE DROP TEST
167-B0602-12
Service Bulletin/Repair Instructions
SB ? 06 - 002 Fuel Filter Usage. This bulletin provides technical information for proper Fuel Filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
167-B0601-12
Service Bulletin/Repair Instructions
SB ? 06 - 001 DESIGN CHANGE OF ENGINE OIL COOLER HOUSING. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retention of liquid gasket used during engine production. This changed the appearance of the engine oil cooler housing but does not affect function or applicability.
167-T0610-12
Service Bulletin/Repair Instructions
06 - 002 No Throttle Response. Once a burnt out tail lamp filament touches a stop lamp filament, the current goes thru the stop lamp circuit causing the ECU to think that the brakes are applied. Therefore stopping acceleration control.
167-B0501-12
Service Bulletin/Repair Instructions
05 - 011 CORRECTIONS TO WORKSHOP MANUALS FOR J08 ENGINES. The standard gap between ends of the second piston ring and the oil ring.
167-B0503-12
Service Bulletin/Repair Instructions
SB ? 05 - 010 CORRECTION TO WORKSHOP MANUALS FOR THE J08E ENGINE. a) Resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 Ohms b) Illustration of the air intake pre-heater terminal should be revised. c) Resistance between terminals of the main relay should be 111 Ohms
167-B0505-12
Service Bulletin/Repair Instructions
SB ? 05 - 007 DESIGN CHANGE OF WATER PIPE FOR J08E
167-B0506-12
Service Bulletin/Repair Instructions
SB ? 05 - 008 This document is to inform the dealers about the addition of the pressure sensor cover and related part for the J08E engine.
167-B0508-12
Service Bulletin/Repair Instructions
SB - 05 - 005 PROPER MAINTENANCE PROCEDURES FOR GREASE LUBRICATED FRONT AXLES
167-B0504-12
Service Bulletin/Repair Instructions
SB - 05 - 003 This document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.