PIP5601C
Service Bulletin/Repair Instructions
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP5601C
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
03-06-01-023I
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
03-06-01-023H
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
16-NA-383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-144
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full Turns.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
03-06-01-023G
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT3665M
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3665L
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
03-06-01-023E
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
RFI20201207_599-
This SKU is a Climate Control Module. The customer communication requested return of unsold inventory to inspect for a software issue. If the software issue exists it can cause a fan in the climate control system to stay on even when the ignition is turned off. The fan staying on even though the ignition is off can drain the battery, making the vehicle unable to start.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3665J
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
030601023D
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
19NA219
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
DOR-K2S2K-10
This SKU is a Pitman Arm. The customer communication requested return of unsold inventory to inspect for the spline size. If the spline size is incorrect it will not have a tight fit with the mating component, and would lead to detectable play and/or noise when steering.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
PIT3665H
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIT3665G
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3472A
This Preliminary Information communication advises the Dealer that the rear end of the vehicle may appear to sag after the vehicle sits overnight or longer. After the vehicle is started, the compressor will engage and the rear of the vehicle will rise to normal operating level. This is normal and no parts should be replaced for this concern.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
This Preliminary information communicates
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP3366C
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5338B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3665F
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
10-00-89-006F
This informational bulletin provides information for dealers how to submit a product information report.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
07-07-30-010D
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIT3665E
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIP3119N
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP4138P
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
07-08-49-020K
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
15-08-44-001H
THIS INFORMATIONAL BULLETIN PROVODES INFORMATION ON THE GM OF CANADA ONSTAR CELLULAR COMMUNICATION UPGRADE.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIT-3665-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HYDRO-BOOST IS NOT SERVICEABLE AND WILL NEED TO BE REPLACED IF THE BRAKE PEDAL MOVES OR APPLIES ON ITS OWN AT A FULL TURN.
PIT-5485-B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5484A
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT3046G
This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
16-NA-025
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIC6140B
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT5353A
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5484
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT5486
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT4943D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIC6140A
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIC5953B
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5464
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIT3137C
This Preliminary Information communication provides information to the technician about the replacement new version compressor will be a dual stage compressor. Technician should not Service Programming System program the replacement module, the module comes preprogrammed.
09-09-40-001C
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIC6107
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6101
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIT5384A
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
02-07-30-052J
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
05-06-04-035E
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
02-08-42-001H
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
05-08-46-006T
This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.
15-08-44-001
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PI02003D
This preliminary informational bulletin provides technicians a recommendation for when they are performing a front end alignment and find an alignment dowel pin missing .
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
05-00-89-055E
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
06-08-47-001K
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
03-00-91-001G
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
030848006J
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
This information provides the proper way to install the floor mats .
PIT5353
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5029F
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT3330G
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option. For vehicles that are 2007 and later a cabin air filter may be able to be added. Refer to the latest version of PI1216.
PIT5264B
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5099A
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
03-06-01-023B
This information bulletin explains how to measure for oil consumpsion and possible reasons for loss of oil.
PIP5232A
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIC6036
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
This informational bulletin provides information on how to use floor mats.
10-00-89-006E
This information bulletin provides the dealers on how to submit a product information report.
PI02003C
This preliminary bulletin provides a diagnostic tip to install a temporary dowl rod to perform an alignment.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
05-02-32-008F
This technical bulletin provides a procedure to replace the power steering pump and line to correct the customers concern of lack of steering assit when stopped or parking lot manuvers.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
10-00-89-006D
This information bulletin provides the dealers on how to submit a product information report.
Recalls
Vehicle Recalls
PIC5088E
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
Programming And Activation Of Replacement OnStar Modules.
05-08-46-006S
This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.
13-00-89-004I
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIP3119M
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
PIT3099L
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
13-00-89-004H
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
PIP3343E
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
PIP3343D
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
13-00-89-004G
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5264
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
13-00-89-004F
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT4943C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
050310020
USE OF NITROGEN GAS IN TIRES. *AK 2015 AND PRIOR GM PASSENGER CARS & TRUCKS (INCLUDING SATURN) ALSO 2008 AND PRIOR HUMMER H2, H3, SAAB 9-7X. UPDATED 5/12/08. *NJ UPDATED 04/15/2014 *JS
08-03-10-006
TIRE SLOWLY GOES FLAT, TIRE AIR LOSS, LOW TIRE PRESSURE WARNING LIGHT ILLUMINATED, ALUMINUM WHEEL BEAD SEAT CORROSION (CLEAN AND RESURFACE WHEEL BEAD SEAT) FOR CERTAIN 2000-2009 GM PASSENGER CARS AND LIGHT DUTY TRUCKS (INCLUDING SATURN). *PE UPDATED 04/15/2014 *JS
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
This informational bulletin provides directions on submitting different PIRs
13-00-89-004E
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
05-00-89-072C
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
13-00-89-004D
This informational bulletin provides an update for 13-00-89-004C to include updated information.
04-06-04-047L
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
10-08-110-001A
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT3099K
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130089009
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIC5904
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
00-03-10-003R
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
PIP4138N
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
10-00-89-010C
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
This informational bulletin provides information on key code security and information on GM key code look up applications.
PIP3119L
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
07-08-49-020H
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
02-07-30-052I
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
08-06-01-006D
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
02-08-98-002D
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
09-00-89-008A
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
05-08-48-001C
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
13-00-89-004B
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PIT4720C
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
13-00-89-005
This technical bulletin provides Warranty Administration - New Labor Codes information.
99-04-20-002H
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
13-00-89-004
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
11-00-89-005D
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
10-00-89-017Z
This informational bulletin provides information on fix it right for first time issues.
00-03-10-002G
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
PIP3140E
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
PIP3119K
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
08-08-51-002A
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
PIP4138L
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT5194
This Preliminary Information communication provides information to the technician about vehicles that will no longer sit level after rear suspension has been serviced. Technician should correctly install the air spring lines that are incorrectly connected.
11-00-89-005C
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIC3718E
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
10-00-89-017X
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
08-08-46-004A
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
080846004A
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
PIT3330F
This Preliminary Information communication provides information to the technician about customers may inquire about the availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.
000089027G
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP3720D
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
06-00-89-026J
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
100089010B
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
12-00-89-002A
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
01-00-89-010J
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
010089010J
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
100089017W
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
PIT4907A
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT3665C
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
PIT4208D
This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available.
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIT3078F
This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.
PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
11-00-89-005B
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
10-00-89-017V
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
PIT-3749D
GM: ON SOME TRUCK MODELS THERE IS SOME FRAME CORROSION. *RM UPDATED ON 5/2/2012. *KB
SB-020842001B
GENERAL MOTORS VEHICLES AND TRUCKS: SUBJECT REGARDING, 2002 AND PRIOR PASSENGER CARS AND TRUCKS, CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. *SLC UPDATED *EH UPDATED 3/30/11. HEADLAMP LENS OVERHEATING WHEN COVERED AND CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. CAN CAUSE CRAZING OR CRACKING OF HEADLAMP LENS. *PE UPDATED 6/24/11. *PE UPDATED 5/14/12. INCLUDING 2013 MODEL YEAR. *PE
09-09-40-001A
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
PIP-4492P
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE
PIP-4138K
GM: THE SERVICE ENGINE SOON LIGHT IS ON, THERE IS ALSO A MISFIRE OR ENGINE NOISE. THERE ARE MULTIPLE POSSIBLE CAUSES. *RM
PIT-3665-A
GENERAL MOTORS: ON ALL 1988-2009 FULL SIZE CHEVROLET/GMC PICKUPS, UTILITIES AND VANS, THE BRAKE PEDAL WILL MOVE DOWN OR SELF APPLY DURING FULL LOCK TURNS OR NEAR FULL LOCK TURNS. CHEVROLET ASTRO AND GMC SAFARI VANS; HUMMER 2 ARE INCLUDED. *PE UPDATED 5/24/11. *PE
SB-10-02-33-001
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. TECHNICIANS HAVE BEEN REPLACING ENTIRE STEERING GEARS DUE TO NOT BEING ABLE TO SERVICE JUST LEAKING PITMAN SHAFT SEAL. *PE UPDATED 5/9/11. *PE
SB-06-02-32-013B
SAAB/HUMMER/GM: DIAGNOSTIC TIPS/RECOMMENDATIONS WHEN POWER STEERING PUMP REPLACEMENT IS NECESSARY. ANALYSIS OF RETURNED POWER STEERING (PS) PUMPS THAT HAD BEEN REPLACED FOR NOISE, NO POWER ASSIST, NO OR LOW PRESSURE AND LEAKING CONDITIONS HAS INDICATED A HIGH NUMBER OF NO TROUBLE FOUND RESULTS. ALL 1997-2010 VEHICLES AND LIGHT TRUCKS; 2010 AND PRIOR HUMMERS H2/H3 AND SAAB 9-7X VEHICLES. *PE
030525007
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS (CLEAN WHEEL SPEED SENSOR MOUNTING SURFACE). *TT UPDATED 10/23/09. *PE
040310001
TIRE PUNCTURE REPAIR PROCEDURES FOR ALL CARS AND LIGHT DUTY TRUCKS. 2008 AND PRIOR GM PASSENGER CARS & LIGHT DUTY TRUCKS (INCLUDING SATURN) AND HUMMER H2, H3 AND SAAB 9-7X. *TT UPDATED. *KB UPDATED 4/11/08. *NJ UPDATED 8/4/09. *PE
TB-090940001
GENERAL MOTORS: THE SEAT BELT BUCKLES NOT OPERATING AND /OR SEAT BELT WARNING LIGHT ILLUMINATION, AS WELL AS DIFFICULTY LATCHING AND UNLATCHING THE BUCKLE OR THE BUCKLE RELEASE BUTTON STICKING. AFFECTS 2010 AND PRIOR GM PASSENGER CARS AND TRUCKS, INCLUDING SATURN.) *PE
000310006
INFORMATION ON TIRE RADIAL FORCE VARIATION (RFV). 2008 AND PRIOR GM PASSENGER CARS AND LIGHT DUTY TRUCKS INCLUDING 2008 AND PRIOR HUMMER H2, H3 AND 2005-08 SAAB 9-7X AND 2000-05 SATURN L SERIES AND 2003-07 SATURN ION. *KB UPDATED 4/11/08. *NJ UPDATED 5/27/09. *PE
08089-B
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
PIT-4722
GMC: FLUID LEAK FROM TRANSMISSION OIL COOLER LINES DUE TO CORROSION. ALL 2000-2006 LIGHT DUTY TRUCKS EQUIPPED WITH THE LIGHT DUTY AUTOMATIC TRANSMISSION. *PE
PIT3504D
SOME CUSTOMERS MAY COMMENT ON VARIOUS HVAC CONCERNS INCLUDING TEMPERATURE DOORS DEFAULTING TO FULL HOT POSITION OR UNABLE TO OBTAIN DEFROST POSITION. *PE
PIT-3046E
GMC: FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL, CAUSING THE LOW FUEL LIGHT TO ILLUMINATE. *PE
000235003N
CLUNKING NOISE UNDER HOOD AND CAN BE FELT IN STEERING WHEEL AND/OR STEERING COLUMN (REPLACE UPPER INTERMEDIATE STEERING SHAFT [I-SHAFT] ASSEMBLY). *PE
04-06-01-029
UNNECESSARY ENGINE CRANKCASE AND SUBSYSTEMS FLUSHING SERVICES, ADDITIVE RECOMMENDATIONS AND PROPER UTILIZATION OF GM SIMPLIFIED MAINTENANCE SCHEDULE TO ENHANCE CUSTOMER SERVICE EXPERIENCE. 2008 AND PRIOR GM CARS AND TRUCKS. *TT UPDATED 3/31/08. *NJ
SB-00-03-10-006C
GENERAL MOTORS: INFORMATION ON TIRE RADIAL FORCE VARIATION. VEHICLE MUST BE DRIVEN BEFORE MEASURING TIRES ON EQUIPMENT HUNTER GSP9700 TOENSURE REMOVAL OF ANY FLATSPOTTING. MODELS INCLUDE ALL GM PASSENGER CARS AND LIGHT TRUCKS, AS WELL AS CERTAIN HUMMERS, SAABS, AND SATURNS. *PE
010842001
HEADLAMPS CONDENSATION AND REPLACEMENT GUIDELINES. KAPERII. *TT 1993-2008 GM PASSENGER CARS AND TRUCKS INCLUDING SATURN. *KB UPDATED 2/26/08. *NJ
070845002
SERVICE ALERT: CONCERNS WITH AFTERMARKET FUSES IN GM VEHICLES 2008 AND PRIOR GM PASSENGER CARS AND LIGHT DUTY TRUCKS (INCLUDING SATURN) *NJ
050604035
USAGE OF E85 FUELS IN GM VEHICLES. 1997 - 2008 ALL GM CARS AND TRUCKS. 1997 - 2008 ALL SATURN VEHICLES. *TT UPDATED. *KB UPDATED ON 10/22/07. *NJ
020603008
LOW VOLTAGE DISPLAY ON IP GAUGE, LIGHTS DIM AT STOP LIGHTS, BATTERY DISCHARGED, NO START, SLOW CRANKING, DIM LIGHTS AT IDLE, LOW GENERATOR OUTPUT. NLM *AR INCLUDES 1990-2008 PASSENGER CARS AND LIGHT DUTY TRUCKS INCLUDING SATURN. UPDATED 07-24-07. *KB UPDATED 11/29/07. *NJ
000090002
INFORMATION ON PROPER TIRE PRESSURE. ALL GM PASSENGER CARS AND LIGHT DUTY TRUCKS FROM 2007 AND PRIOR. *KB
060139002
FRONT BLOWER MOTOR INOPERATIVE OR MAY NOT SHUT OFF IN EXTREMELY LOW AMBIENT TEMPERATURE CONDITIONS. *KB
030604030
MULTIPLE DRIVEABILITY SYMPTOMS OF LONG OR HARD STARTS, CHUGGLE, ROUGH IDLE AND LIGHT OR INTERMITTENT MISFIRE DUE TO CLOGGED FUEL INJECTORS. *TT
000235003
CLUNKING NOISE UNDER HOOD AND CAN BE FELT IN STEERING WHEEL. *EH UPDATED *EH UPDATED. *KB
030730007
DELAYED ENGAGEMENT WHEN SHIFTING INTO THESE POSITIONS. PARK INTO REVERSE, NUETRAL INTO DRIVE, NUETRAL INTO REVERSE, AND PARK INTO DRIVE. THIS BULLETIN INCLUDES ALL 2000 - 2007 GM LIGHT DUTY TRUCKS. *KB
060089024
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES. THIS BULLETIN INCLUDES 2007 AND PRIOR PASSENGER CARS AND TRUCKS INCLUDING SATURN. *KB
990940005
INFORMATION ON THE AVAILABILITY OF SEAT BELT EXTENDERS FOR 2000 AND PRIOR PASSENGER CARS AND TRUCKS. *TT UPDATED THIS BULLETIN CONTAINS 2007 AND PRIOR PASSENGER CARS AND TRUCKS INCLUDING SATURNS. *KB
3340
LEFT FRONT AXLE SHAFT DIFFICULT TO REMOVE. AXLE DIFFERENTIAL LEAK SEAL SHAFT. *KB
050089078
FUEL SYSTEM TREATMENT PLUS, FUEL SENDING UNIT CORROSION AND FUEL SYSTEM DEPOSITS. 2007 AND PRIOR GM PASSENGER CARS AND TRUCKS INCLUDING SATURNS. *KB
060310010
INFORMATION ON PROPER WHEEL CHANGING PROCEDURES AND CAUTIONS. 2007 AND PRIOR GM PASSENGER CARS AND TRUCKS INCLUDING SATURN. *KB
990851007
THIS BULLETIN UPDATES GMCS POSITION ON REFINISHING ALUMINUM WHEELS FOR 2003 AND PRIOR PASSENGER CAR AND TRUCKS. *TT 2007 AND PRIOR PASSENGER CARS AND TRUCKS INCLUDING SATURN. UPDATED. *KB
010730042
SOME VEHICLES MAY EXHIBIT A CLUNK NOISE THAT CAN BE HEARD ON A 2-3 UPSHIFT ON 2002 AND PRIOR LIGHT DUTY TRUCKS. *TT UPDATE. 2007 AND PRIOR PASSENGER CARS AND LIGHT DUTY TRUCKS. *KB
030730043
INFORMATION REGARDING AUTOMATIC TRANSMISSION SHIFT LOCK CONTROL FUNCTION. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT UPDATING TO 2007 AND PRIOR PASSENGER CARS AND TRUCKS. *KB
060421001
UPDATED TRANSFER CASE CONNECTOR SERVICE KIT NOW AVAILABLE FOR TRANSFER CASE SPEED SENSOR WIRE HARNESS CONNECTOR THAT COMES LOOSE OR CONNECTOR RETAINER CLIP BREAKS. 2007 AND PRIOR GM LIGHT DUTY TRUCKS. *KB
060845004
INSTRUMENT PANEL, BODY AND GENERAL WIRING HARNESS REPAIR. 2007 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
020603009
BATTERY CHARGING TIPS - 1990-2003 PASSENGER CARS AND LIGHT DUTY TRUCKS, 1990-2003 ISUZU LIGHT DUTY TRUCKS, 2003 HUMMER H2. NLM 1990 - 2007 GM PASSENGER CARS AND LIGHT DUTY TRUCKS (INCLUDING SATURN); 1990 - 2007 ISUZU LIGHT DUTY TRUCKS. *TT
020604015
INTERMITTENT NO CRANK, NO START CONDITION FOR 2001-2002 PASSENGER CARS AND TRUCKS. *SLC 2001-2007 GM PASSENGER CARS AND LIGHT-DUTY TRUCKS (INCLUDING SATURN). *TT
060308002
REVISED UPPER CONTROL ARM REPLACEMENT. *TT
030605008B
ADVANCE SERVICE INFORMATION - EXHAUST SYSTEM POPPING/SNAPPING NOISE WHEN VEHICLE IS HOT, AT IDLE OR IMMEDIATELY AFTER VEHICLE IS SHUT OFF. *TT BULLETIN 03-06-05-008, DATED 11/01/2003 REPLACED. *TT
000089008E
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
010730030A
DIAGNOSTIC INFORMATION ON HARSH 1-2 UPSHIFT. 2001-2002 PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *YH TO INCLUDE 2003-2006 PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT
010730036D
DIAGNOSTIC TIPS FOR DIAGNOSTIC TROUBLE CODE P0756. 2006 AND PRIOR PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT
010730038B
THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
050850012
UNWANTED/LOOSE SEAT MOVEMENT. *TT
000604033
I/M READINESS AS PART OF EMISSION INSPECTION AND MAINTENANCE PROGRAM FOR OBD II VEHICLES. *TT
030844022
PARTS RESTRICTION ON ORDERING XM DIGITAL RADIO RECEIVER. 2002-2004 CARS AND TRUCKS. *TT 2002-2006 PASSENGER CARS AND TRUCKS (INCLUDING SATURN). *TT
040844009A
XM DIGITAL RADIO RECEIVER ORDERING PROCESS. *MJ PARTS RESTRICTION ON ORDERING XM DIGITAL RADIO RECEIVER. 2002-2006 PASSENGER CARS AND TRUCKS (INCLUDING SATURN). *TT
050846006A
INFORMATION ON UPGRADING CERTAIN ONSTAR GENERATION 5 ANALOG/DIGITAL-READY SYSTEMS TO ONSTAR GENERATION 6 DUAL-MODE (ANALOG/DIGITAL). *TT
020730024A
DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
030604012
INSPECTION OF ALL RELATED WIRING HARNESS CONNECTIONS WHEN DIAGNOSING MISCELLANEOUS DIAGNOSTIC TROUBLE CODES, INTERMITTENT DRIVEABILITY CONCERNS, HARD START, NO START, INCORRECT GAUGES, INOPERATIVE AIR CONDITIONING SYSTEMS, SERVICE ENGINE SOON LAMPS ILLUMINATED, 4WD LAMP ILLUMINATED, INSTRUMENT PANEL GAUGES INOPERATIVE, CRUISE INOPERATIVE. 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
030730007A
ENGAGEMENT TIME OF ELECTRONICALLY CONTROLLED TRANSMISSIONS IN GENERAL MOTORS VEHICLES. VARIOUS MODELS INCLUDING 2000-2006 ALL LIGHT DUTY TRUCKS. *TT
040850016B
MEMORY SEAT MAY NOT RETURN TO REQUESTED POSITION. *EH
050307009
VEHICLE WHEEL ALIGNMENT REQUIREMENTS AND RECOMMENDATIONS. 2006 AND PRIOR PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT
050850008
INTERMITTENT HEATED SEATS INOPERATIVE, DIAGNOSTIC TROUBLE CODE B3941 SET. *TT
990940005B
SEAT BELT EXTENDER AVAILABILITY. GM MODELS 2014 AND PRIOR GM CARS AND TRUCK. *TT
050603002
BATTERY AND CHARGING SYSTEM ELECTRICAL DIAGNOSTICS. 1997 - 2006 ALL GM CARS AND TRUCKS. *TT
010418001C
DRIVELINE CHARACTERISTICS FOR ALL-WHEEL DRIVE (AWD) AND FOUR-WHEEL DRIVE (4WD) SYSTEMS. *TT UPDATED *EH
050309007
REVISED SHOCK ABSORBER BOLT TIGHTENING SPECIFICATION. *TT
050866004
NEW LIFTGATE STRUT BALL STUD TIGHTENING SPECIFICATION. *TT
010842001B
EXTERIOR LAMP CONDENSATION AND REPLACEMENT GUIDELINES. VARIOUS MODELS INCLUDING 1993-2006 PASSENGER CARS AND LIGHT AND MEDIUM DUTY TRUCKS. *TT
050090004
REVISED FRONT AND REAR DRIVE AXLE FLUID CAPACITIES AND WHEEL NUT TORQUE SPECIFICATION. *TT
050601014
OIL LEAK UNDER EXTREME COLD TEMPERATURES (-34 DEGREES C) (-30 DEGREES F) OR COLDER). *TT
050730013
4L60-E/4L65-E AUTOMATIC TRANSMISSION SECOND GEAR START, LACK/LOSS OF POWER WHEN ACCELERATING FROM A STOP. *TT
010526001
LOW EFFORT PARKING BRAKE APPLY SYSTEM. *TT
050308006
REVISED STABILIZER SHAFT LINK REPLACEMENT PROCEDURE AND FASTENER TIGHTENING SPECIFICATIONS. 1999 - 2005 CHEVROLET AND GMC FULL SIZE PICKUP AND UTILITY MODELS. *TT
03102005
THE A PILLAR SUNROOF DRAIN HOSE MAY BE MISROUTED AND WATER MAY BE ENTERING THE AIR INLET OF THE HVAC CASE. *EH
020307002
REVISED FRONT CASTER AND CAMBER ADJUSTMENT PROCEDURE. ORIGINAL NOT YET RECEIVED. *TT
020846006
INCORRECT ONSTAR GLOBAL POSITION SYSTEM (GPS) LOCATION REPORTED DURING ONSTAR CALL FOR 2000 - 2002 PASSENGER CARS AND LIGHT DUTY TRUCKS WITH ONSTAR. *TT UPDATE TO ADD 2005 MODELS. *TT
030848005A
COMPASS ZONE ADJUSTMENT AND CALIBRATION PROCEDURE DURING PRE-DELIVERY INSPECTION. VARIOUS MODELS INCLUDING 2002-2004 LIGHT DUTY TRUCKS. *TT UPDATE TO INCLUDE 2005 BUICK ALLURE. *TT
040604047C
TOP TIER DETERGENT GASOLINE. 2005 AND PRIOR ALL GENERAL MOTORS PASSENGER CARS AND TRUCKS ALSO INCLUDED. *TT UPDATE. *TT
040844005
UTILIZING TECH 2 TO RETRIEVE PART NUMBERS FOR RADIOS, COMPACT DISC (CD) CHANGERS AND INSTRUMENT PANEL CLUSTERS (IPC). 2000-2004 PASSENGER CARS AND TRUCKS. *MJ 2005 MODELS ADDED. *TT
050089018
GM PARTS ORDERING SYSTEM. ALL 2005 AND PRIOR GM AND TRUCKS. *TT
050604021
REVISED INSPECTION/MAINTENANCE (I/M) EVAPORATIVE EMISSION (EVAP) SYSTEM SET PROCEDURE. *TT
050604022
TOP TIER DETERGENT GASOLINE (DEPOSITS, FUEL ECONOMY, NO START, POWER, PERFORMANCE, STALL CONCERNS). 2005 AND PRIOR ALL GENERAL, SAAB AND SATURN CARS AND TRUCKS. *TT
050846004
ONSTAR PHONE NUMBER CONCERNS (PHONE NUMBER INCORRECT/ASSIGNED TO ANOTHER VEHICLE/PHONE) THAT OCCUR DURING DIAGNOSIS OF ONSTAR SYSTEM. 2000-2005 GM PASSENGER CARS AND TRUCKS AND 2003-2005 SATURN VEHICLES WITH ONSTAR. *TT
050846005
ONSTAR LABOR OPERATION CODES. 1996-2005 GM PASSENGER CARS AND TRUCKS AND SATURN VEHICLES. *TT
000846003
GLOBAL POSITION SENSOR (GPS) PERFORMANCE DEGRADATION. 1996 - 2005 PASSENGER CARS AND TRUCKS. 2002 - 2005 SATURN VEHICLES. *TT
702
NAVIGATION RADIO HUM. THIS APPLIES TO 2003-05 CHEVROLET/GMC/CADILLAC/HUMMER H2 FULL SIZE UTILITIES. GM TECH LINKS. *TT
01202005
WINDSHIELD WIPER PULSE FUNCTION. *TT
000310003G
GM NEW VEHICLE TIRE WARRANTY PROGRAM. *TT 1996-2005 PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT
030844018A
REAR SEAT AUDIO (RSA) AND/OR REAR HVAC INOPERATIVE. *TT UPDATE. *TT
040601034
INSTRUCTIONS TO BE FOLLOWED TO AID IN OBTAINING ROOT CAUSE ANALYSIS ON BOTH OEM AND GOODWRENCH ENGINES TRANSMISSIONS AND TRANSFER CASES. THIS INCLUDES 2005 AND PRIOR GM PASSENGER CARS AND TRUCKS. *EH
040730013
AUTOMATIC TRANSMISSION SHIFT, ENGINE DRIVEABILITY CONCERNS OR SERVICE ENGINE SOON (SRS) LIGHT ON AS A RESULT OF THE INSTALLATION OF AN AFTERMARKET REUSABLE, EXCESSIVELY OILED AIR FILTER. 2004 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *MJ 2005 AND PRIOR. *TT
040849018D
CRANKS BUT NO START STALL INACCURATE INCORRECT FUEL GAUGE READING NO FUEL VEHICLE IS OUT OF FUEL AND FUEL GAUGE READS ABOVE EMPTY. THIS INCLUDES 2001 -04 CADILLAC TRUCKS AND 1999-05 CHEVROLET AND GMC TRUCKS. *EH
050308002
REPLACEMENT OF SHOCK ABSORBERS AND STRUTS AND USE OF LABOR OPERATION. THIS ALSO INCLUDES 2005 AND PRIOR PASSENGERS CARS AND TRUCKS ALSO INCLUDE SATURN VEHICLES. *EH
050844001
COMPACT DISC OR DVD PLAYER SKIPPING INOPERATIVE SLUGGISH AND OR LONG SEARCH TIMES. THIS INCLUDES 2005 AND PRIOR GM PASSENGER CARS TRUCKS AND SATURN MODELS.*EH
000522002D
BRAKE WARRANTY SERVICE PROCEDURES. 1999-2004 ALL GM, ISUZU, SAAB AND SATURN PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT UPDATE. *TT UPDATE. *TT
030089047
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF DECEMBER 1, 2003 AND DECEMBER 8, 2003. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
040849018C
CRANKS BUT NO START, STALL, INACCURATE / INCORRECT FUEL GAUGE READING, NO FUEL, VEHICLE IS OUT OF FUEL AND FUEL GAUGE READS ABOVE EMPTY. 1999-2004 CHEVROLET, GMC AND CADILLAC TRUCKS. *MJ UPDATE. *TT
020730001A
DIAGNOSTIC INFORMATION ON DIAGNOSTIC TROUBLE CODE P1870, TRANSMISSION COMPONENT SLIPPING FOR 2000 - 2002 PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT UPDATE TO INCLUDE 2004 MODELS. *TT UPDATED *EH
020846010E
PROGRAMMING ONSTAR MODULE FOR CANADIAN FRENCH VOICE RECOGNITION. *TT UPDATE. *TT UPDATED *EH
000601012
USE OF SURFACE CONDITIONING DISKS. *EH
010844005A
INFORMATION ON ERROR CODES ON RADIO DISPLAY THEIR CAUSE AND CORRECTIVE ACTION. *EH
030089006B
NEW VEHICLE PRE-DELIVERY INSPECTION - GENERATING HIGHER CSI SCORES. 2003 - 2004 HUMMER H2 AND ALL 2003-2004 CARS AND TRUCKS. *TT UPDATED *EH
030861003A
PAINT PEELING FROM SIDE ASSIST STEP. *TT UPDATED *EH
030898002A
SQUEEZE TYPE RESISTANCE SPOT WELDING/EQUIPMENT. *TT UPDATED *EH
040138013
HVAC NOT COLD ENOUGH A/C COMPRESSOR DOES NOT ENGAGE . *EH
040138014
HIGH PITCHED TONE HEARD INSIDE VEHICLE WHEN AC COMPRESSOR IS ENGAGED. *EH
040138015
DIAGNOSTIC INFORMATION FOR MOAN GROAN OR BOOM NOISE AT IDLE VIBRATION IN STEERING WHEEL OR FELT THROUGH FLOOR WHEN AC COMPRESSOR ENGAGES DO NOT REPLACE AC COMPRESSOR. *EH
040604065
ENGINEERING INVESTIGATION (EI #04073) HIGH, LOW OR ERRATIC OIL PRESSURE GAUGE READING SETTING DIAGNOSTIC TROUBLE CODES P0522 AND/OR P0523. 2004 ISUZU W4 ALSO INCLUDED. *TT UPDATE. *TT
040849008
MIDDLE EAST EXPORT HUMMER H2 TIRES SERVICE AND CLUSTER ENHANCEMENT SPECIAL SERVICE PROCEDURES. *EH UPDATE. *TT
610
WINDSHIELD UPPER REVEAL MOLDING WHICH MAY CONTRIBUTE TO WIND NOISE IN THE WINDSHIELD AREA. GM TECH LINK. *TT
839605
RADIO TELEPHONE/MOBILE RADIO (TRANSCEIVER) INSTALLATION AND TROUBLESHOOTING GUIDELINES. 1990-2005 PASSENGER CARS AND TRUCKS. ORIGINAL NOT YET RECEIVED. *TT
010138006C
CONTAMINATED R-134A AIR CONDITIONING SYSTEMS -AIR CONDITIONING SYSTEM FLUSHING PROCEDURES AND UNIVERSAL IN-LINE AIR CONDITIONING FILTER INSTALLATION. 1993 - 2005 PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT
030138019
UNDERHOOD AIR CONDITIONER RATTLE NOISE HEARD ON ACCELERATION OR A SUDDEN LOSS OF AIR CONDITIONER SYSTEM PERFORMANCE. *TT THIS BULLETIN REPLACES 03-01-38-019 DATED 11-01-2003. TO INCLUDE VARIOUS MODLES INCLUDING 2002-2004 COMMERCIAL UPFITTER CHASSIS VEHICLES. *TT
040307002
NEW ALIGNMENT PROCEDURE FOR LABOR OPERATION NUMBERS E2020 AND E2000. 2001-2005 PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT
040310012
PITTING AND BRAKE DUST ON CHROME WHEELS. ALSO INCLUDES 2005 AND PRIOR GM CARS AND TRUCKS. *TT
040604051
MAINTENANCE CLEANING OF FUEL INJECTORS. 2005 AND PRIOR ALL GENERAL MOTORS PASSENGER CARS AND TRUCKS INCLUDED. *TT
040730037
RELEASE OF DEXRON III (H-REVISION) AUTOMATIC TRANSMISSION FLUID (ATF). 2005 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
040868002
CRUISE CONTROL OPERATION -- INCREASING SET SPEED. INCLUDING 2004-2005 PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT
609
A/C LOW PRESSURE SWITCH DIAGNOSIS. *SC
08182004
SINGLE REAR AIR SUSPENSION COMPRESSOR DISCONTINUED AND IS REPLACED WITH THE DUAL AIR COMPRESSOR USED ON THE 2005 MODEL. *TT
010089015
DEALER INSTALLED REGULAR PRODUCTION OPTIONS (RPO) AND REGULAR PRODUCTION ACCESSORIES (RPA). 2005 AND PRIOR PASSENGER <A TITLE="CLICK FOR MORE INFORMATION ABOUT CAR" STYLE="TEXT-DECORATION: NONE; BORDER-BOTTOM: MEDIUM SOLID GREEN;" HREF="HTTP://SEARCH.TARGETWORDS.COM/U.SEARCH?X=5977|1||||CARS|AA1VDW">CAR</A>S AND LIGHT DUTY TRUCKS. *TT
020089002B
INFORMATION FOR DEALERS ON HOW TO SUBMIT A FIELD PRODUCT REPORT. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT *AR
020139007
AUTOMATIC DUAL ZONE HVAC BATTERY DRAW. *AR
030091001A
VIBRATION ANALYSIS WORKSHEET. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT *AR
030730002A
TRANSMISSION COOLING SYSTEM SERVICE TOOL J 45096 - TRANSFLOW INFORMATION. *TT
040089030
FIELD PRODUCT REMINDER - CAR AND TRUCK "FIX IT RIGHT THE FIRST TIME" ISSUES AND BULLETINS RELEASED WEEKS OF JUNE 28, 2004 AND JULY 19, 2004. *AR
040089035
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF AUGUST 9, 2004 AND AUGUST 16, 2004. *TT
040138010
DIAGNOSTIC INFORMATION TO ACCURATELY DIAGNOSE A/C LOW PRESSURE SWITCH USING NEW KENT MOORE SPECIAL TOOL GE-47742. *TT
040139009
HVAC BLOWER MOTOR INOPERATIVE OR STAYS RUNNING. *TT
040604054
NON-GM PARTS AND ACCESSORIES (AFTERMARKET). 2005 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
07082004
GM SERVICE TECHNICAL COLLEGE. *EH
000089027
ELIMINATING UNWANTED ODORS IN VEHICLES. *EH
000310002
CHEMICAL STAINING OF CHROME WHEELS. *EH
010138006B
CONTAMINATED R134A A/C SYSTEMS - AIR CONDITIONING SYSTEM FLUSHING PROCEDURES AND GUIDELINES. INCLUDING 1993-2004 PASSENGER CARS AND LIGHT DUTY TRUCKS. *EH
020603010
BATTERY PARASITIC DRAIN. THIS SERVICE BULLETIN REPLACES 020603010. *EH
040089026
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF JUNE 14 2004 AND JUNE 21 2004. *EH
07012004
OIL LIFE SYSTEM RESET PROCEDURES-TRUCKS. BUICK TERAZZA 2005, GMC SIERRA DENALI 2002-2003, GMC B7 CHASSIS MEDIUM DUTY 2003-2005 AND GMC 560 C-SERIES 2003-2005 *SC
0040089021
FIELD PRODUCT REMINDER CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF MAY 17, 2004 AND MAY 24, 2004. *EH
020730029D
PRODUCT QUALITY CENTER FOR ENGINE AND TRANSMISSION ASSEMBLY AND TRANSFER CASE REPLACEMENT. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT 2005 AND PRIOR PASSENGER VEHICLES AND LIGHT DUTY TRUCKS. *TT
020844007
NEGATIVE IMPACT OF DEALER INSTALLED CLOTH VINYL ROOFS ON XM RADIO AND OR ONSTAR SYSTEMS. THIS SERVICE BULLETIN REPLACES 020844007. *EH
040089024
FIELD PRODUCT REMINDER CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF MAY 31, 2004 AND JUNE 7, 2004. *EH
040399001
NEW AIR SUSPENSION PRESSURIZATION PROCEDURE. *EH
040601019
GM PERFORMANCE PARTS ENGINE WARRANTY Q & A. 2004 AND PRIOR GM PASSENGER CANS AND TRUCKS. *TT
040604043
UNABLE TO RESET ENGINE OIL LIFE MONITOR. *TT
0406040445
OIL LIFE MONITORING SYSTEM - PCM RESET. 2004 ALL GM PASSENGER CARS AND TRUCKS. *TT
040852005
REMOTE KEYLESS ENTRY (RKE) SYSTEM INOPERATIVE. *TT
040898001
ADDITIONAL MATERIAL AND SOURCE FOR METAL PANEL BONDING ADHESIVES. 2004 PRIOR PASSENGER VEHICLES AND TRUCKS. *MJ
990138006A
J-43600 ACR 2000 ESSENTIAL REFRIGERANT RECOVER/RECHARGE EQUIPMENT. 1993-2005 PASSENGER CARS AND LIGHT TRUCKS. *TT
01881
ENGINE CONTINUES TO RUN WHEN YOU TAKE THE KEY OUT OF THE IGNITION. *TT
05022004
OPTION B2E VICTORY RED PACKAGE. *EH
000310002A
CHEMICAL STAINING OF CHROME WHEELS. 2004 AND PRIOR PASSENGER VEHICLES AND TRUCKS. *TT
030864010
OUTSIDE REARVIEW MIRRORS MAY BLOW IN AT HIGHWAY SPEEDS OR POWER FOLDING FEATURE APPEARS INOPERATIVE. ALSO TO INCLUDE 2005 MODELS. *TT
040089016
FIELD PRODUCT REMINDER - FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF APRIL 19, 2004 AND APRIL 26, 2004. ALSO INCLUDES 2005 AND PRIOR PASSENGER VEHICLES AND TRUCKS. *TT
040089019
VEHICLE AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS WEEKS OF MAY 3, 2004 AND MAY 10, 2004. PRIOR PASSENGER VEHICLES AND TRUCKS. *MJ
040601013
INFORMATION ON SERPENTINE BELT WEAR. *EH
040604036
WARRANTY COVERAGE CHANGE FOR EMISSION-RELATED REPROGRAMMING EVENTS. 2005 AND PRIOR GM PASSENGER VEHICLES AND TRUCKS. *MJ
040842009
AVAILABILITY OF REPLACEMENT REAR TAIL LAMP OUTBOARD RETAINER CLIPS AFTER LAMP ASSEMBLY REMOVAL/REPOSITIONING FOR BULB REPLACEMENT OR SERVICE. *MJ
04202004
WHEN SWITCHING THE WINDSHIELD WIPER SPEED FROM LOW TO INTERMITTENT, THE SPEED REMAINS IN THE LOW. GM VOICEMAIL EXPRESS. *TT
000235003C
CLUNKING NOISE UNDER HOOD AND CAN BE FELT IN THE STEERING WHEEL. *TT
000310003F
GM NEW VEHICLE TIRE WARRANTY PROGRAM. INCLUDING 1996 - 2004 PASSENGER CARS AND LIGHT DUTY TRUCKS AND 2003-2004 HUMMER H2. THIS BULLETIN REPLACED BULLETIN 00-03-10-003D DATED 01/2003. *TT THIS BULLETIN REPLACED BULLETIN 00-03-10-003F. *TT
010310003A
GM OF CANADA NEW VEHICLE LIMITED WARRANTY TIRE PROGRAM. 1996-2005 ALL PASSENGER CARS AND LIGHT DUTY TRUCKS. ORIGINAL WAS NOT RECEIVED. *TT
010310012A
GUIDELINES FOR USING E2020-WHEEL ALIGNMENTS, E2000-TOE ADJUST AND E0200, E0201, E0203, E0204-WHEEL BALANCE. 1989-2005 PASSENGER CARS AND LIGHT DUTY TRUCKS. BULLETIN 01-03-10-012A NOT YET RECEIVED. *TT
040089010
NEW SERVICE BULLETIN APPEARANCE AND PRINTING INFORMATION. OTHER MODELS INCLUDING 2005 AND PRIOR PASSENGER AUTOMOBILES AND TRUCKS. *TT
040089011
PART AND ACCESSORY REPLACEMENT POLICY. 2004 AND PRIOR PASSENGER AUTOMOBILES AND TRUCKS AND 2004 AND PRIOR HUMMER H2. *TT
040089013
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF MARCH 22, 2004 AND MARCH 29, 2004. *TT
040089014
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF APRIL 5, 2004 AND APRIL 12, 2004. *TT
040843003
REPLACEMENT OF WINDSHIELD WIPER INSERTS. THIS INCLUDES 2002-04 GM PASSENGER CARS AND LIGHT DUTY TRUCKS. *EH
620504A
OPERATING PROCEDURES - 18 POINTS. BULLETIN 62-05-04A NOT YET RECEIVED. 2005 AND PRIOR PASSENGER CARS AND TRUCKS INCLUDED. *TT
03092004
ROOF RACK RATTLE. *TT
020089017A
ESSENTIAL TOOLS THAT INCLUDE CONSUMABLE PARTS/ELECTRICAL TERMINALS. 2004 AND PRIOR GM PASSENGER VEHICLES AND TRUCKS AND 2004 AND PRIOR ISUZU LIGHT AND MEDIUM DUTY TRUCKS. *TT
030604033
REVISED DIAGNOSTIC TROUBLE CODE P0336. *TT UPDATE. TO INCLUDE 2004 ISUZU NQR COMMERCIAL MODELS. *TT
040089008
AUTOMOBILE AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF FEBRUARY 23, 2004 AND MARCH 1, 2004. 2004 AND PRIOR PASSENGER VEHICLES AND TRUCKS AND 2004 AND PRIOR HUMMER H2. *TT
040089009
FIELD PRODUCT REMINDER - AUTOMOBILE AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF MARCH 8, 2004 AND MARCH 15, 2004. 2005 AND PRIOR PASSENGER AUTOMOBILES AND TRUCKS AND 2004 AND PRIOR HUMMER H2. *TT
040495001
REVISED WHEEL DRIVE SHAFT NUT TORQUE SPECIFICATION. *TT
040850003
ENABLING MEMORY SEAT FEATURE VIA DIC IF FEATURE APPEARS INOPERATIVE. *EH
040850006
MINOR WRINKLES/CREASES, DISCOLORATION, CIGARETTE BURNS AND CUSTOMER INDUCED CUTS AND STRAINS ON FRONT AND REAR DRIVER AND PASSENGER SEATS WITH LEATHER, VINYL OR CLOTH SEAT COVERS. 2004 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *MJ
040850007
SERVICE INFORMATION FOR FRONT HEATED SEAT INOPERATIVE/COLD. *MJ
02262004
WIND WHISTLE HEARD COMING FROM THE ROOF AREA. *TT REVISED INFORMATION. *TT
02232004
LABORINSTALLED RPA B57, THE UP LEVEL CHROME APPEARANCE PACKAGE IS .7 HOURS. 2004 VICTORY RED LIMITED EDITION H2S.
02132004
IGNITION KEY CAN NOT BE REMOVED FROM THE LOCK CYLINDER - SERVICE TIP. *TT
02092004
ICE BUILDUP IN THE AREA OF THE FRONT LOWER DOOR HINGE PILLARS. *TT
000602006
DEX-COOL ENGINE COOLANT INFORMATION. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
010730031
1-2, 2-3, 3-4, 4-5 SHIFT AND TORQUE CONVERTER CLUTCH (TCC) CHARACTERISTICS DURING COLD WEATHER OPERATION ON 4L60-E, 4L80-E OR ALLISON TRANSMISSIONS. TO INCLUDE 2001-2004 CHEVROLET AND GMC LIGHT DUTY FULL-SIZE PICKUP AND UTILITY MODELS. *TT
020089005
DEALER DISCLOSURE REQUIREMENTS. TO INCLUDE 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
040089002
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF JANUARY 12, 2004 AND JANUARY 19, 2004. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. 2004 AND PRIOR HUMMER H2. *TT
040089003
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF JANUARY 26, 2004 AND FEBRUARY 2, 2004. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
040089004
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF FEBRUARY 9, 2004 AND FEBRUARY 16, 2004. 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
040603001
INCORRECT AMP CODE GENERATOR. *EH
040603002
DIAGNOSTIC INFORMATION FOR INTERMITTENT VEHICLE NO CRANK DEAD BATTERY. *EH
040730006
4L65 4L60E 4L60 AND 2004R AUTOMATIC TRANSMISSION OIL PUMP SPRING FIRST AND SECOND DESIGN IDENTIFICATION. *EH
01292004
TIRE PUNCTURE REPAIR PROCEDURES FOR GM VEHICLES, BOTH CARS AND LIGHT-DUTY TRUCKS, DUE TO ROAD DEBRIS BEING ENCOUNTERED. *TT
01232004
RATTLE IN THE REAR STOWAGE COMPARTMENT OF THE VEHICLE. GM VOICEMAIL EXPRESS. *TT
00372D
ONSTAR SYSTEM IS ATTEMPTING AND/OR COMPLETING PHONE CALLS WHICH THE OPERATOR OF THE VEHICLE DID NOT INITIATE. *TT
00702
SLIP CONDITION IN 2ND, 3RD OR 4TH DAMAGED 2-4 BAND 3-4 CLUTCH ON THE 4L60E/4L65E AUTOMATIC TRANSMISSION. *TT *MJ
00823A
POWER STEERING FLUID LEAKING AT HYDRAULIC BRAKE BOOSTER. *TT
00872A
OIL PAN OR OIL COOLER LINE LEAK ON GEN III V-8 ENGINES EQUIPPED WITH AN OIL COOLER. *TT
00993
OUTSIDE REARVIEW MIRROR GLASS MAY CRACK. *TT
01004A
DIAGNOSTIC TROUBLE CODE (DTC) C0660 STORED IN VEHICLE HISTORY. SERVICE VME. *TT 2005 HUMMER H2 ADDED. *TT
01012004
GENERAL INFORMATION ON RESETTING THE GM OIL LIFE SYSTEM. 03-05 CHEVROLET ALL FULL SIZE TRUCKS AND UTILITIES AND 03-05 GMC ALL FULL SIZE TRUCKS AND UTILITIES AND 03-05 CADILLAC FULL SIZE UTILITIES AND 2005 HUMMER H2. *TT
010730042A
INFORMATION ON 2-3 UPSHIFT OR 3-2 DONWSHIFT CLUNK NOISE FOR 2003 AND PRIOR LIGHT DUTY TRUCKS. *TT THIS BULLETIN REPLACES 01-07-30-042A DATED 10/01/2002. 2004 AND PRIOR LIGHT DUTY TRUCKS. *TT
01353
ENGINE MISFIRE DUE TO INJECTOR FRETTING CORROSION. *TT
01483
VEHICLE HAS NO PCM (POWER TRAIN CONTROL MODULE) COMMUNICATION WITH TECH 2. SIT BULLETIN 1400427. *TT
01502
4L65E TRANSMISSION SHIFTS FREQUENTLY. SERVICE VME. SIT BULLETIN 1402886. *TT
01555
D HEIGHT SPECIFICATION MISSING FROM SI. SIT BULLETIN 1410632. *TT
01592
2003-2004 GENERATION 5 ONSTAR STEERING WHEEL CONTROL FUNCTION EXPLANATION. SIT BULLETIN 1416474. *TT
01599
4L60E, 4L65E FORWARD AND LOW REVERSE WAVED STEEL CLUTCH PLATE APPEARANCE CHANGE. *TT
01634
INTERMEDIATE STEERING SHAFT SERVICE KIT. SERVICE VME. *TT
01634A
SUPPLEMENT TO 00-02-35-003D - CLUNKING NOISE UNDER HOOD AND CAN BE FELT IN THE STEERING WHEEL. *TT
01654
SQUAWK OR GRUNT NOISE THAT OCCURS ON THE 2-3 UPSHIFT ON VEHICLES WITH 4L60E - M30, 4L60E M32 TRANSMISSION. *TT
01669
SQUEAK AT REAR OF VEHICLE.*MR
01691
REAR LIFTGATE RATTLE, CHUCKING NOISE. SIT BULLETIN 1442699. *TT
01704
PROGRAMMING CONTROL HEADS - HVAC AC. *TT
01710
RATTLE IN REAR STOWAGE. SERVICE VME. SIT BULLETIN 1454806. *TT
01714
THE 4L60E/4L65E AUTOMATIC TRANSMISSION MAY EXPERIENCE A LEAK, INOPERATIVE/SLIPPING IN 2ND, 3RD AND 4TH GEARS OR NO MOVEMENT (NO FORWARD OR REVERSE) DUE TO EXCESS FLUID LOSS. SIT BULLETIN 1455088. *TT
01718
STARTER CLICKS - NO CRANK CONDITION. *TT
01729
ONSTAR WHITE DOT BUTTON VISUAL CHANGE BUILD SCHEDULE. SIT BULLETIN 1459145. *TT
01743
SERVICE VME - ICE ACCUMULATION AT THE LOWER FRONT DOOR HINGE PILLARS. SIT BULLETIN 1460391. *TT
01839A
ROOF RACK CROSS BAR WIND WHISTLE NOISE. SERVICE VME. *TT
01864
RADIO CD SKIPS/EJECTS OR CLOCK RESETS TO 12:00. *MR *TT
01890
ROOF RACK CROSS BAR RATTLE. *TT
01919
REPLACEMENT RADIO READS CAL ERROR, HAS NO AUDIO OR WILL NOT PROGRAM. *TT
01919A
REPLACEMENT RADIO READS CAL ERROR, HAS NO AUDIO OR WILL NOT PROGRAM. *TT
01924
FRONT LOWER CONTROL ARM CHANGE. *MR
01939
4.3 4.8 5.3 6.0 LR4 LU3 LM7 L59 LQ4 LQ9 ENGINES- EVAP CODE P0442. *MR
01955
PASSENGER DOOR MODULE LOCK UP.*MR
01958
PRODUCT INFORMATION REGARDING RADIO PERSONALIZATION. *MR
01997B
ONE OR SEVERAL OF THE FASTENING NUTS ON THE BACKSIDE OF THE FUEL FILLER DOOR ASSEMBLY WERE NOT ORIENTED PROPERLY CAUSING AN INTERFERENCE WITH THE VEHICLE'S FUEL FILLER DOOR OPENING WHEN ATTEMPTING TO INSTALL THIS ACCESSORY ONTO THE VEHICLE. SERVICE VMW CONCERNING CHROME FUEL FILLER DOOR ASSEMBLY INSTALLATION. *NM
02003
MISSING ALIGNMENT DOWEL PIN. ALL 1999-2004 CHEVROLET FULL SIZE TRUCKS AND UTILITIES, 1999-2004 GMC FULL SIZE TRUCKS AND UTILITIES, 2002-2004 CADILLAC FULL SIZE TRUCKS AND UTILITIES. *MR
02007
POWER FOLDING MIRRORS WILL NOT FOLD INWARD.*MR
02041
PASSENGER SIDE AIR BAG DISCOLORATION - SIR ON 2004 CHEVROLET, GMC AND CADILLAC ALL FULL SIZE TRUCKS AND UTILITIES AS WELL. *TT
02045
INFORMATION ON OPTION B2E VICTORY RED BICYCLE. SERVICE VME. *TT
02046
NAVIGATION SCREEN LOCKS UP. *TT
02054
ELIMINATION OF LOW COOLANT MESSAGE FROM DIC. SERVICE VME. *TT
02060
NO AUDIO AND RADIO DISPLAY INOPERATIVE OR CLOCK RESETS. *TT
02068
NO START WITH DIAGNOSTIC TROUBLE CODE (DTC) P1626 OR P1631. ALSO INCLUDES 1998-2004 CHEVROLET, GMC FULL SIZE TRUCKS/ UTILITIES/ VANS. *TT
02078
POWER STEERING PUMPS - NOT PAINTED. SERVICE VME. *TT
02080
REPEAT HVAC ACTUATOR REPLACEMENT. *TT
02082
PASSENGER DOOR FUNCTIONS INOPERATIVE AND/OR SERVICE TIRE PRESSURE MONITOR MESSAGE. ALSO INCLUDES 2004 CHEVROLET, GMC AND CADILLAC FULL SIZE TRUCKS AND UTILITIES. *TT
02149
CLOCK NOT KEEPING PROPER TIME ON VEHICLES WITH NAVIGATION RADIO. *TT
040089001
FIELD PRODUCT REMINDER - <A TITLE="CLICK FOR MORE INFORMATION ABOUT CAR" STYLE="TEXT-DECORATION: NONE; BORDER-BOTTOM: MEDIUM SOLID GREEN;" HREF="HTTP://SEARCH.TARGETWORDS.COM/U.SEARCH?X=5977|1||||CARS|AA1VDW">CAR</A> AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF DECEMBER 15, 2003 AND JANUARY 5, 2004. 2004 AND PRIOR PASSENGERS CARS AND TRUCKS. 2004 AND PRIOR HUMMER H2. *TT
040848001
REAR WINDOW DEFOGGER - BROKEN HEATING GRID DETECTION METHOD. 2004 AND PRIOR PASSENGER CARS AND LIGHT DUTY TRUCKS. *TT UPDATED *EH
1530076
VEHICLES AND HUMMER H2 WITH A HIGH ALTITUDE STALL. *MJ
3000
SERVICE VME - 03 - 04 FULL SIZE TRUCK, UTILITIES AND HUMMER H2 PASSENGER DOOR MODULE INOPERATIVE. *MJ
3000A
REAR AXLE LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS. *MJ
3015
6.0L LQ4 VIN U ENGINE RESTRICTION. *TT
3018
ENGINE CYLINDER HEAD CUP PLUG COOLANT LEAK. *MJ
3022A
04 FULL SIZE TRUCKS AND UTILITIES WITH VIN G, N, T, V AND U ENGINES MAY HAVE A HIGH ALTITUDE, HIGH AMBIENT TEMPERATURE STALL. *TT
3024
RADIO PRESET READS SOMETHINGF OTHER THAN THE STATION ID OR STATION CALL LETTERS. *MJ
3025
04 MODEL YEAR 4.8.5.3.7.6.0 GEN III ENGINE PISTON PIN INFORMATION. *MJ
3031
UPDATES TO SI AND THE PI NUMBERING PROCESS. SERVICE VME. 2004-05 PASSENGER VEHICLES AND LIGHT DUTY TRUCKS INCLUDING HUMMER H2). *TT
3038
ENGINE TICK, RATTLE OR KNOCK NOISE AFTER CYLINDER HEAD GASKET REPLACEMENT ON THE 6.0L ENGINE. *TT
3039
AUTO VOLUME INOPERATIVE AFTER IGNITION KEY IS CYCLED. VARIOUS MODELS INCLUDING 03-04 CADILLAC ALL FULL SIZE UTILITIES. *TT
3045A
4485 4484 SHUDDER OR BIND ON TURNS IN 4 HI. *SC
3050A
02-05 ONSTAR EQUIPPED VEHICLES EMITTING BEEPING NOISE BEFORE CONNECTING TO ONSTAR. *TT
3052
PROPANE OR NATURAL GAS TYPE ODOR FROM VEHICLE. *TT
3054
REPLACEMENT FLEXPLATE MAY HAVE LARGER BOLT HOLES THAN THE ORIGINAL FLEXPLATE. *TT
3055
SERVICE ENGINE SOON LIGHT WITH A P0300 MISFIRE DUE TO MISFIRES MAINLY ON CYLINDER 7. *TT
3058
GOODWRENCH ENGINE AND REPLACEMENT CRANKSHAFT INFORMATION. *TT
3060
KEY CODE LOOK-UP. 1990-2005 ALL MAKES/MODELS INCLUDING HUMMER H2. *TT
3086
WHISTLE NOISE FROM THE THROTTLE BODY AREA ON LIGHT THROTTLE ACCELERATION ON VEHICLES WITH GEN III ENGINES AND ELECTRONIC THROTTLE. *TT
3087
CRANK NO START WITH NO CRANKING RPM SPARK OR INJECTOR PULSE. *TT
3090
UNABLE TO PERFORM SET UP NEW ONSTAR ON VEHICLES WITH GEN 6.05 HARDWARE. *SC
3097
OIL PAN OR OIL COOLER LINE LEAK. *SC
3106
XM RADIO WAS WORKING PRIOR TO JULY 26, 2004 AND IT IS INOPERATIVE NOW. *JB
3107
P0420 AND P0430 DTSC IN THE DETROIT, MICHIGAN AREA WITH GEN III V-8 ENGINES. *SC
3111
NAVIGATION SYSTEM COVERAGE OF CANADA. (2004-2005 CHEVROLET TRAILBLAZER, 2004-2005 GMC ENVOY, 2004-2005 BUICK RAINIER/RENDEZVOUS, 2004-2005 CADILLAC ESCALADE, 2005 CHEVROLET AVALANCHE/SUBURBAN/TAHOE, 2004-2005 GMC DENALI, 2005 GMC YUKON, AND 2005 HUMMER H2) *SC
3113
GEN 6 VEHICLES IN MOUNT AIRY, NC CANNOT CONNECT TO ONSTAR OR EMERGENCY SERVICES. *SC
3119
ENGINEERING INVESTIGATION - CATALYTIC CONVERTER REPLACEMENT. *SC
3120
ONSTAR CENTER UNABLE TO PERFORM REMOTE DIAGNOSTIC. (2004-2005 CHEVROLET YUKON, 2005 CHEVROLET TRAILBLAZER, 2002, 2003, 2005 BUICK RAINIER, 2005 CHEVROLET EXPRESS VAN, AND 2005 CADILLAC SEVILLE) *SC
3121
EXHAUST VIBRATION RESONANCE OR MOAN IN VEHICLES WITH GEN III V8 ENGINES. *TC
3121A
EXHAUST VIBRATION RESONANCE OR MOAN 99-05 FULL SIZE TRUCKS AND UTILITY VEHICLES WITH GEN 3 V-8 ENGINES. *TC
3137
REAR AIR SUSPENSION COMPRESSOR SERVICE PART CHANGE. *SC
3146
ALL GENERAL MOTORS LIGHT DUTY TRUCKS AND HUMMER H2 BRIDGESTONE DUELER A/T TIRES SIZE LT285/75R16 LOAD RANGE D. *TC
3148
WINDSHIELD MOLDING REPLACEMENT. *TC
3161
EXCESSIVE BRAKE OR SPONGY BRAKE PEDAL. 03-05 CHEVROLET FULL SIZE TRUCKS AND UTILITIES. 03-05 GMC FULL SIZE TRUCKS AND UTILITIES. 03-05 CADILLAC/HUMMER H2 ALL FULL SIZE TRUCKS AND UTILITIES. *TC
3179
AUTOMATIC DUAL ZONE HVAC BATTERY DRAW SUPPLEMENT TO 02-01-39-007A. *TT
020848001A
URETHANE ADHESIVES FOR STATIONARY GLASS AND OTHER APPLICATIONS. 2004 AND PRIOR PASSENGER CARS AND TRUCKS AND 2004 AND PRIOR ISUZU TRUCKS. *TT
030089045
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF NOVEMBER 17, 2003 AND NOVEMBER 24, 2003. 2004 AND PRIOR PASSENGER CARS AND TRUCKS INCLUDED. *TT
00843C
REPLACEMENT (RKE) TRANSMITTER IS INOPERATIVE - SERVICE VME. *TT
01339
HVAC BLOWER MOTOR FAN STAYS ON IN THE HIGH BLOWER POSITION. SERVICE VME. *TT
01456
THE NAV RADIO SYSTEM NOT AVAILABLE WITH CD CHANGER INFORMATION. SERVICE VME. *TT
020089006A
NEW ADD TIME FOR LABOR OPERATION L2300 - CONVERTER, OXIDATION CATALYTIC - REPLACE. OTHER MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS . *TT
020604057D
LABOR OPERATION ASSIGNMENTS FOR CONTROL MODULE PROGRAMMING. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS, 2003-2004 KODIAK C4500-C8500 AND TOPKICK C4500-C8500 SERIES MODELS. *TT
030089038
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF OCTOBER 20, 2003 AND OCTOBER 27, 2003. *TT
030089039
SEARCH TIPS FOR LOCATING PRELIMINARY INFORMATION (PI) DOCUMENTS IN SERVICE INFORMATION (SI). VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
030089043
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF NOVEMBER 3, 2003 AND NOVEMBER 10, 2003. VARIOUS OTHER MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
030730056
4L60-E AUTOMATIC TRANSMISSION OIL PUMP FIRST AND SECOND DESIGN IDENTIFICATION. *TT
100803
IMPORTANT POINTS RELATIVE TO THE H2 NAVIGATION RADIO SYSTEM. GM VOICEMIAL LOG. *TT
010089010A
INFORMATION ON USE OF DIAGNOSTIC WORKSHEET. 2004 AND PRIOR MODEL YEAR PASSENGER CARS AND TRUCKS. *TT
020604057C
LABOR OPERATION ASSIGNMENTS FOR CONTROL MODULE PROGRAMMING. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS, 2003-2004 KODIAK C4500-C8500 AND TOPKICK C4500-C8500 SERIES MODELS. *TT
030089031
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF SEPTEMBER 22, 2003 AND SEPTEMBER 29, 2003. 2004 AND PRIOR PASSENGER CARS AND TRUCKS AS WELL AS 2004 AND PRIOR HUMMER H2. *TT
030089034
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES, PARTS RESTRICTION INFORMATION AND BULLETINS RELEASED WEEKS OF OCTOBER 6, 2003 AND OCTOBER 13, 2003. 2004 AND PRIOR PASSENGER CARS AND TRUCKS AS WELL AS 2004 AND PRIOR HUMMER H2. *TT
030234001A
INNER TIE ROD RELEASED FOR SERVICE. *TT
030604060
INFORMATION ON NEW SPARK PLUGS AND GAPPING. VARIOUS MODELS INCLUDING PONTIAC GTO 2004. *TT
030848006
REPAIR INFORMATION FOR RECONNECTION OF REAR WINDOW DEFROSTER CONTACT OR TAB. 2000-2004 LIGHT AND MEDIUM DUTY TRUCKS AND 2003-2004 HUMMER H2 WITH ELECTRIC REAR WINDOW DEFROSTER. *TT
030851002
CHANGES TO PAINT CLAIM SUBMISSION PROCESS. *TT
030866011
STINGER MAC ACCESSORIES (SMA) SPARE TIRE CARRIER MAY RATTLE OVER ROUGH SURFACES, T-PIN LOCK DIFFICULT TO REMOVE. *TT
092303
FRONT PASSENGER SEATBELT ASSEMBLY REPLACEMENT. GM VOICEMAIL LOG. *TT
092603
WHEN REPLACING THE INNER TIE ROD IT IS NOT NECESSARY TO REPLACE THE ENTIRE STEERING LINKAGE RELAY ROD KIT. GM VOICEMAIL LOG. *TT
090803
DEALER INSTALLED OPTIONS AND AFTERMARKET ACCESSORIES INSTALLATION IMPROVEMENTS. GM VOICEMAIL LOG. *TT
000089008B
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
030089024
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF AUGUST 4, 2003, AUGUST 11, 2003 AND AUGUST 18, 2003. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
030089027
SUBLET ADMINISTRATIVE ALLOWANCE (COVERAGE S) LABOR OPERATIONS. VARIOUS MODELS INCLUDING 2004 AND PRIOR GM PASSENGER CARS AND TRUCKS. *TT
030089028
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF AUGUST 25, 2003 AND SEPTEMBER 1, 2003. 2004 AND PRIOR PASSENGER CARS, TRUCKS AND 2004 AND PRIOR HUMMER H2. *TT
030089029
OPTIMIZING CUSTOMER SATISFACTION WITH DEALER INSTALLED OPTIONS AND ACCESSORIES. *TT
030089030
FIELD PRODUCT REMINDER - CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF SEPTEMBER 8, 2003 AND SEPTEMBER 15, 2003. 2004 AND PRIOR PASSENGER CARS, TRUCKS AND 2004 AND PRIOR HUMMER H2. *TT
030846004
PROPER DIAGNOSIS OF ONSTAR SYSTEM AND INFORMATION NECESSARY WHEN CONTACTING GM TECHNICAL ASSISTANCE CENTER (TAC) REGARDING ONSTAR PARTS RESTRICTION PROGRAM CONCERNS ON VARIOUS MODELS INCLUDING 1996-2004 PASSENGER CARS AND TRUCKS. *TT
030852005
DIAGNOSTIC INFORMATION FOR REPLACEMENT REMOTE KEYLESS ENTRY (RKE) TRANSMITTER INOPERATIVE - UNABLE TO SYNCHRONIZE. *TT
082903
INSTALLATION OF TAIL LAMP BRUSH GUARDS. VME MESSAGE. *TT
030089008A
CORROSION PROTECTION FOR DEALER INSTALLED ACCESSORIES FASTENED TO METAL PANELS. THIS INCLUDES 2004 AND PRIOR PASSENGER CARS AND TRUCKS. THIS SERVICE BULLETIN REPLACES 030089008. *EH
030089021
NEW VEHICLE PRE DELIVERY INSPECTION PERCEIVED FUEL ECONOMY AND DRIVER INFORMATION CENTER SETTINGS. *EH
030089022
CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF JULY 21, 2003 AND JULY 28, 2003. VARIOUS MODELS INCLUDING 2004 AND PRIOR PASSENGER CARS AND TRUCKS. *TT
030601023
HIGHER THAN EXPECTED OIL CONSUMPTION <8500 GVW. VARIOUS MODELS INCLUDING 2003-2004 CHEVROLET KODIAK (C4500-C5500 SERIES MODELS)AND GMC TOPKICK (C4500-C5500 SERIES MODELS). *TT
990420002B
DRIVELINE CLUNK. VARIOUS MODELS INCLUDING 2004 AND PRIOR LIGHT DUTY TRUCK MODELS. *TT
010897001B
HOMELINK TRANSCEIVER GARAGE DOOR OPENER TRANSMITTER TEST KIT AVAILABLE AS ESSENTIAL TOOL. THIS SERVICE BULLETIN REPLACES 010897001. THIS ALSO INCLUDES 2004 AND PRIOR GM PASSENGER CARS AND TRUCKS. *EH
030089017
FIELD PRODUCT REMINDER CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF JUNE 16 2003 AND JUNE 23 2003. *EH
030089019
FIELD PRODUCT REMINDER CAR AND TRUCK FIX IT RIGHT THE FIRST TIME ISSUES AND BULLETINS RELEASED WEEKS OF JULY 7 2003 AND JULY 14 2003. *EH
062303
OFF ROAD STOP LAMP PACKAGE - A REVISED HARNESS TO BE SHIPPED. *TT
030139008
CHANGES IN AIR CONDITIONING COMPESSOR ON/OFF INSTRUMENT PANEL DISPLAY SYMBOL FROM 2003 TO 2004 MODEL YEAR AND SYNCHRONIZING THE DRIVER AND PASSENGER SET TEMPERATURES. *TT
030730027
MOST FREQUENTLY ASKED QUESTIONS AND ANSWERS FOR J 45096 TRANSFLOW TRANSMISSION OIL COOLING SYSTEM FLUSHING MACHINE. 2004 AND PRIOR PASSENGER CARS AND LIGHT DUTY TRUCKS WITH AUTOMATIC TRANSMISSION/TRANSAXLE AND 2004 AND PRIOR HUMMER H2. *TT
990089021D
EXPEDITING WARRANTY PARTS. 2004 AND PRIOR PASSENGER CARS, TRUCKS AND HUMMER H2. *TT
990730022A
SHIFT STABILIZATION AND TOW/HAUL MODE FEATURE FOR HYDRA-MATIC 4L60-E/4L65-E AND 4L80-E/4L85-E TRANSMISSIONS. *TT
01432
AUTOMATIC TRANSMISSION POOR ACCELERATION, PERFORMANCE. *TT
01479
TUBULAR SIDE STEPS EXHIBIT CORROSION. SERVICE VME. *TT
10142002
EXTERIOR MIRROR CURB VIEW ASSIST PROGRAMMING FUNCTIONS AND FEATURES. *TT
3044
GENERATION 5 ONSTAR STEERING WHEEL CONTROL FUNCTION. *TT
3045
SHUDDER OR BIND ON TRUNS IN 4 HI. *EH UPDATED 03-01-07. *KB
3046A
FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL. *TT
3056
CHECK ENGINE LIGHT WITH A P0300 DUE TO 2-4 CYLINDERS MISFIRING ON THE SAME BANK OF THE ENGINE. *TT
3078
SOME 2004 FULL SIZE TRUCKS AND UTILITIES MAY EXPERIENCE A DIAGNOSTIC TROUBLE CODE P0442. *TT
3089
SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT
3136
THE 4L60E/4L65E AUTOMATIC TRANSMISSION SLIP CONDITION IN 2ND, 3RD, OR 4TH GEAR. ALSO TO INCLUDE THE PONTIAC GTO 2005. *TC
3170
HARSH 1-2 SHIFT. *EH
3215
INSTRUMENT PANEL CLUSTER GUAGES FLOAT UP AFTER IGNITION KEY TURNED OFF. VARIOUS MODELS INCLUDING 99-05 CHEVROLET, GMC AND CADILLAC FULL SIZE UTILITIES. *TT
3232
1999 - 2005 GEN II COLD ENGINE MISFIRE AT IDLE WITH POSSIBLE P0171 AND/OR P0174. *TT
3280
RUST FOUND IN THE INJECTOR INLET FILTER DURING INJECTOR REPAIRS. *TT
3287B
HEATED SEAT INOPERATIVE OR SHUT OFF IN 30 SECONDS. DIAGNOSTIC TROUBLE CODES B2435, B2440, B3606 AND/OR B1825 SET IN THE DRIVERS SEAT MODULE. *TT
3288
POWER FOLDING MIRRORS WILL NOT FOLD INWARD. THIS ALSO INCLUDES 03-05 CHEVROLET GMC AND CADILLAC FULL SIZE TRUCKS AND UTILITIES WITH DL3. *EH
3310
LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE MANEUVERS. 99 - 05 CHEVROLET/GMC/CADILLAC/HUMMER H2 ALL FULL SIZE TRUCKS UTILITIES AND VANS. *TT
3324
SERVICE AIR SUSPENSION MESSAGE AFTER REPLACING THE AIR SUSPENSION COMPRESSOR ASSEMBLY FROM A SINGLE STAGE COMPRESSOR TO A DUAL STAGE COMPRESSOR. MAY ALSO HAVE A CURRENT OR HISTORY CODE C0660 AND/OR C0712. *TT
3367A
REAR AIR SUSPENSION - TRIM HEIGHT TOOL SET. *TT
3382
IGNITION KEY CAN NOT BE ROTATED IN STEERING COLUM LOCK CYLINDER. THIS INCLUDES 1999-05 CHEVROLET AND GMC FULL SIZE TRUCKS AND UTILITY. *EH
3386
LACK OF STEERING ASSIST OR SHUDDER DURING PARKING LOT TYPE MANEUVERS. *TT
3405
WINDSHIELD WIPER PULSE FUNCTION. *TT
3424
ELECTRONIC TRANSFER CASE UNABLE TO COMPLETE SHIFT. *TT
3461
REAR AIR SUSPENSION IN-OP DTC C0563. *TT
3472
REAR END OF THE VEHICLE APPEARS TO SAG AFTER THE VEHICLE SITS OVERNIGHT OR LONGER. *TT
3499
STEERING IDLER ARM INSPECTION PROCEDURE. *TT
3503
REAR AIR SUSPENSION LEAK-DOWN. *TT
3509
VEHICLE SITS LOW OR THE SUSPENSION SAGS OVERNIGHT. *TT
3521
ANTI-LOCK BRAKING SYSTEM (ABS) LIGHT ON SPEEDOMETER MAY BE ERRATIC. DIAGNOSTIC TROUBLE CODE (DTC) C0055 C0235 C0236 OR C0237 STORED IN THE EBCM. *TT 1998-2008 ALL CHEVROLET, GMC, BUICK, AND OLDSMOBILE MID-SIZED TRUCKS AND UTILITIES. 1998-2008 ALL CHEVROLET, GMC, AND CADILLAC FULL SIZED TRUCKS AND UTILITIES. *KB UPDATED ON 09/20/07. *NJ
3600
SERVICE VME - SUNROOF MOTOR REPLACEMENT INFORMATION. *TT
4231
SERVICE VME. SUPPLEMENT TO 00-02-35-003L. UPDATE ON NEW I-SHAFT. *KB
4486
ONE OF THE FOLLOWING CONCERNS WHEN PROGRAMMING THE MILEAGE OR THE HOURS INTO AN EXCHANGE INSTRUMENT PANEL CLUSTER THAT IS RECEIVED FROM AN ELECTRONIC SERVICE CENTER (ESC). *NJ
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.