Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9D3 OL
Hyundai has become aware that your Hyundai Elantra equipped with a 2.0 ATK engine may have been incorrectly updated with Cylinder Noise Detection System (CNDS) software intended only for Korean-built Elantra vehicles and may not meet specifications.
26-01-039H DN
Certain Elantra (ADA) vehicles may have been incorrectly updated with Cylinder Noise Detection System (CNDS) software that can set DTC P132700; this software was intended only for Korean-built Elantra (AD) vehicles. In addition, the California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
26-01-039H TSB
Certain Elantra (ADA) vehicles may have been incorrectly updated with Cylinder Noise Detection System (CNDS) software that can set DTC P132700; this software was intended only for Korean-built Elantra (AD) vehicles. This bulletin provides instructions to perform a software update for the Engine Control Module (ECM) to revert to the original ROM ID, apply the emissions label under the hood, and provide the vehicle owner with Proof of Correction.
26-EE-003H TSB
Some vehicles may exhibit difficulty starting in cold weather. This bulletin provides the procedure to perform an inspection on the starter magnetic switch for potential freezing and, if necessary, replace the starter magnetic switch (solenoid) assembly.
DTN DCS
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
P33 OL
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-089H DCS
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-BD-012H TSB
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-01-024H-1 TSB
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
25-01-024H EM
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.
25-01-024H TSB
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
24-01-009H-1
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-BD-001H
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-094H
This bulletin describes the procedure to repair a head lamp that has an inoperable high beam function.
23-01-014H-5
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-AT-010H
Certain vehicles equipped with the Intelligent Variable Transmission (IVT) may experience a check engine light or malfunction indicator light due to Diagnostic Trouble Codes (DTC) listed below. This bulletin provides information on replacing the oil pressure sensor to remedy these DTCs, rather than replacing the entire IVT assembly.
23-BE-010H
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
23-01-014H-4
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-01-014H-3
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-01-014H-2
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
23-01-014H-1
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-01-014H
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. Please note that all Hyundai vehicles meet or exceed Federal Motor Vehicle Safety Standards. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
23-BD-002H
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-EM-010H
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
218/231 amend
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
22-01-043H
Hyundai is conducting a service campaign to enhance the knock sensor logic with the Cylinder Noise Diagnostic System (CNDS) software update. CNDS is to detect abnormal cylinder wall scuffing or noise of the engine block before potentially severe engine damage occurs. If abnormal noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously. In addition, DTC P1327 will be recorded in the ECM.
22-EM-008H
Hyundai is conducting a service campaign 974 to enhance the knock sensor logic with the Cylinder Noise Diagnostic System (CNDS) software update. CNDS is to detect abnormal cylinder wall scuffing or noise of the engine block before potentially severe engine damage occurs. If abnormal noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously. In addition, DTC P1327 will be recorded in the ECM.
22-ST-005H
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
22-01-030H
Certain 20MY Elantra (AD/ADa) vehicles may experience an illuminated check engine warning light due to Diagnostic Trouble Codes (DTC) listed below. Perform the Transmission Control Unit (TCU) update, and, if necessary, replace the IVT (Intelligent Variable Transmission) to resolve this condition. This update also includes the software for optimizing CLR_DIST (distance traveled since DTCs cleared) display. ⢠TCU DTC Codes: P0730, P0731, P0741, P0867, P1603
21-ST-003H
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing
21-01-041H
This bulletin provides information related to the Engine Control Module (ECM) software update for 2020MY Elantra (AD/ADA) vehicles equipped with 2.0L engine to revise the logic for the DTCs listed below. ï· P0068 - Manifold Pressure (MAP) Sensor/Mass Air flow (MAF) Sensor - Throttle Position Correlation ï· P0101 - Mass Air flow (MAF) Sensor - Range/Performance ï· P0106 - MAP Sensor / Baro Pressure (BARO) Sensor B (#1) - Range/Performance
21-01-039H
Certain 20MY Elantra (AD/ADa) vehicles may experience an illuminated check engine warning light due to Diagnostic Trouble Codes (DTC) listed below. Perform the Transmission Control Unit (TCU) update, and, if necessary, replace the IVT (Intelligent Variable Transmission) to resolve this condition. This update also includes the software for optimizing CLR_DIST (distance traveled since DTCs cleared) display.
21-EM-004H
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures.
21-BE-004H
When using Wireless CarPlay, the system may intermittently auto disconnect. When Wireless CarPlay is disconnected, a pop up message âPhone Not Responding. Please reconnect it and try againâ will appear on the radio screen.
21-BE-006H
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with the front multifunction camera may exhibit one or more of the following warnings on the instrument cluster; Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB). This bulletin describes the procedure to replace the front camera/ multi-function camera.
21-EM-003H
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
21-01-004H
This bulletin describes the procedure to repair a headlamp that has an inoperable high beam function.
20-BE-014H
When using Wireless CarPlay, the system may intermittently auto disconnect. When Wireless CarPlay is disconnected, a pop up message âPhone Not Responding. Please reconnect it and try againâ will appear on the radio screen.
20-01-047H
Certain 20MY Elantra (AD/ADa) vehicles may experience an illuminated check engine warning light due to Diagnostic Trouble Codes (DTC) listed below. Perform the Transmission Control Unit (TCU) update, and, if necessary, replace the IVT (Intelligent Variable Transmission) to resolve this condition.
20-BR-002H
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-01-039H
This bulletin provides information and procedures for collecting OBD âIn Use Monitor Performance Ratioâ (IUMPR) data on certain 2019-2021MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board).
20-BE-006H-1
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with the front multifunction camera may exhibit one or more of the following warnings on the instrument cluster; Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB). This bulletin describes the procedure to replace the front camera/ multi-function camera.
20-ST-002H-2
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-ST-003H-1
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-ST-001H-1
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-002H-1
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-ST-003H
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
20-FL-007H
This bulletin provides information related to an ECM (Engine Control Module) software update for DTC P0128: Coolant Thermostat (Coolant Temp below Thermostat Regulating Temperature) logic revision. There are no drivability symptoms associated with DTC P0128.
20-01-028H
Certain vehicles may experience an illuminated warning light due to Diagnostic Trouble Codes (DTC). Perform the ECU and TCU update, and, if necessary, replace the IVT (Intelligent Variable Transmission) to resolve this condition. ï· TCU DTC Codes: P0730, P0731, P0741, P0867, P1603 ï· ECU DTC Codes: P0106, P0068, P0101
Campaign T5B Dea
Certain vehicles may experience an illuminated warning light due to Diagnostic Trouble Codes (DTC). This service campaign provides information on the procedures to perform the ECU and TCU update, and, if necessary, replace the IVT (Intelligent Variable Transmission) to resolve this condition. ⢠TCU DTC Codes: P0730, P0731, P0741, P0867, P1603 ⢠ECU DTC Codes: P0106, P0068, P0101
20-FL-004H
This bulletin describes the Idle Stop and Go (ISG) system operation, diagnostic and battery sensor recalibration procedure. Refer to applicable Shop Manual and Ownerâs Manual for additional information.
20-ST-002H
A bearing noise may develop within the Motor Driven Power Steering (MDPS) column of the housing worm gear assembly. If bearing noise is heard, follow the procedure in this bulletin and if necessary, replace the steering column and housing.
20-SS-002H(1)
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-BE-006H
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with front camera/multi-function camera may exhibit a series of Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB) warnings and function conditions on the instrument cluster. This bulletin describes the procedure to replace the front camera/ multi-function camera.
20-BD-007H
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-BE-004H
Some 2019 & 2020 Elantra (ADa) vehicles equipped with halogen headlights may experience intermittent operation of the high beam. This bulletin provides the service procedure to replace the left and right headlamp assemblies and perform aiming adjustments.
20-EE-002H(1)
This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.
20-SS-001H
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-BE-001H
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
19-01-042H
This bulletin provides information and procedures for collecting OBD ?In Use Monitor Performance Ratio? (IUMPR) data on certain 2019-2020MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board). Data is no longer submitted to Hyundai by datasheet and dealer email. Data is sent electronically by GDS when the procedure of this bulletin is followed.
19-AT-021H-1
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-GI-006H
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-AT-016H
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
19-AT-010H
This bulletin provides a procedure to transfer pressure data to the ECU/TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.