Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
Z05 OL
Warranty Program/Extension
Certain vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
Z01 Letter
Warranty Program/Extension
Certain 2012 – 2017 model year Accent, 2012 – 2017 model year Azera, 2013 – 2018 model year Santa Fe Sport, 2013 – 2019 model year Santa Fe, and 2012 – 2017 model year Veloster vehicles may exhibit an intermittent airbag warning light and diagnostic trouble codes (DTCs) may be set. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the Occupant Classification System (OCS)/Occupant Detection System (ODS) under these conditions has been extended to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.
26-01-013H-2 DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
26-01-013H-2 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
9C2 060518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
9C2 DCS 260518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
26-BD-002H DN
Warranty Program/Extension
Some Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.
26-BD-002H TSB
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners. The warranty extension does not apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer or has a branded or similar title under any state’s law.
26-BE-011H DN
Warranty Program/Extension
Some vehicles listed below may exhibit an intermittent airbag warning light and DTC(s) B1763 (OCS ECU Defect), and/or B1764 (OCS Mat Defect) may be stored. Hyundai is extending the warranty coverage of the sensor for the Occupant Classification System (OCS) / Occupant Detection System (ODS) to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Refer to the warranty and parts information outlined in this bulletin.
26-BE-011H TSB
Warranty Program/Extension
Some vehicles listed below may exhibit an intermittent airbag warning light and DTC(s) B1763 (OCS ECU Defect), and/or B1764 (OCS Mat Defect) may be stored. Hyundai is extending the warranty coverage of the sensor for the Occupant Classification System (OCS) / Occupant Detection System (ODS) to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Refer to the warranty and parts information outlilned in this bulletin. This bulletin contains the procedure to inspect for the airbag warning light and DTC(s), replace the OCS (ODS) unit or wire harness, reset the OCS (ODS), and initialize the power seat module (if applicable). This TSB also contains the procedure to replace the OCS (ODS) mat if DTCs exist after replacement of the OCS (ODS) wire harness.
9C2 OL
Service Campaign
Certain 2019 – 2020 model year Santa Fe, 2017 – 2018 model year Santa Fe Sport, 2015 – 2019 model year Sonata, and 2018 – 2021 model year Tucson vehicles may exhibit elevated engine-out emissions. Hyundai is conducting a service campaign to update the Engine Control Module (ECM) Software for vehicles equipped with the (2.4 GDI) Theta II engine to improve engine combustion and fuel trim adaptations.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
9C2 Susp DCS
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
9C2 Susp DN
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
26-01-013H-1 DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H-1 DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
26-01-013H-1 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
26-01-013H TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
P33 OL
Other
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-089H DCS
Other
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
Other
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
Other
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-BD-004H OL
Warranty Program/Extension
Certain 2015 – 2018 model year Elantra, 2015 – 2019 model year Sonata, 2017 – 2021 model year Tucson, 2017 – 2018 model year Santa Fe Sport, 2019 model year Santa Fe, 2021 – 2023 model year Santa Fe Hybrid, and 2020 – 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H EM
Warranty Program/Extension
Some vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H DN
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any state’s law.
25-BD-004H TSB
Warranty Program/Extension
Description: Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any state’s law.
25-01-024H-1 TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
24-01-050H-1
Service Campaign
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-050H
Service Bulletin/Repair Instructions
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-009H-1
Service Campaign
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-AT-002H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-014H-5
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-01-063H
Service Bulletin/Repair Instructions
In some areas, a vehicleâs underbody may exhibit corrosion due to road salt usage. As a preventative measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the bottom exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain Santa Fe Sport (AN) vehicles.
23-BE-010H
Service Bulletin/Repair Instructions
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
23-01-014H-4
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-01-014H-3
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-BD-010H
Service Bulletin/Repair Instructions
Certain 2017-2018MY Elantra (ADa), Sonata (LFa), and Santa Fe Sport (AN) vehicles manufactured by Hyundai Motor Manufacturing Alabama (âHMMAâ) may exhibit peeling or bubbling of the white paint in various areas of the vehicle, most commonly on or around the hood, fender, and roof. The paint warranty coverage for these vehicles with white exterior paint has been extended to the following: ⢠2017MY vehicles â 6 years with unlimited miles from the date of original retail delivery or date of first use, whichever occurred first, and is valid for original and subsequent owners ⢠2018MY vehicles â 5 years with unlimited miles from the date of original retail delivery or date of first use, whichever occurred first, and is valid for original and subsequent owners
22-01-073H
Service Bulletin/Repair Instructions
Certain 2017-2018MY Santa Fe Sport (AN) vehicles received an incorrectly labeled fuse cover during Recall 218.
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
22-01-033H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
22-EM-001H-1
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
22-EM-002H-1
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Warranty coverage is valid for original and subsequent owners.
DBPT3G
Service Bulletin/Repair Instructions
Certain vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.
22-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Electric Waste Gate Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ⢠Check Engine Light illumination with EWGA related DTC. ⢠Intermittently high/low turbocharger boost pressures. ⢠Abnormal noise from the turbocharger.
22-EM-001H
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
TXXI DBP
Service Bulletin/Repair Instructions
The warranty coverage for certain Theta II engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
DBP972
Service Bulletin/Repair Instructions
When asked to provide the Modem Information, the Universal Subscriber Identity Module (USIM) may not be available. This TSB# 21-01-080H describes the 3-part software to correct this condition and activate Blue Link Services.
21-01-066H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
T3GDBP20211103
Service Bulletin/Repair Instructions
Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P1326.
21-EM-009H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Electric Waste Gate Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ⢠Check Engine Light illumination with EWGA related DTC. ⢠Intermittently high/low turbocharger boost pressures. ⢠Abnormal noise from the turbocharger. ⢠Reduced engine power.
21-EM-008H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Variable Charge Motion Controllers (VCM) equipped in the applicable vehicles listed below. This bulletin also provides information on the use of the Service Kit for 2.4L equipped engines, which enables replacing the VCM Lever Arm without replacing the complete Intake Manifold Assembly. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ï Check Engine Light illumination with VCM related DTC. ï Unstable engine RPM and reduced engine power. ï Abnormal noise from the intake manifold whenever engine RPM is raised from idle speed.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
21-01-002H
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block for engine repairs or replacement related to connecting rod bearing damage as described in Campaign T3G (Seized and/or BCT No Pass Result Only) has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Please refer to TSB # 20-01-024H-2 (or latest revision) for applicable part numbers and labor ops.
20-01-004H-3
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H-2
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-01-004H-2
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H-1
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
20-01-037H
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
20-ST-001H-2
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
TXXI Dealer Best
Service Bulletin/Repair Instructions
This Dealer Best Practice intends to inform dealers of a proposed settlement (âSettlementâ) for a class action lawsuit filed against Hyundai Motor America (âHMAâ). Beginning in July 2020, customers affected by the proposed settlement will begin becoming informed of the settlement by mailed notice and email, and they may direct questions to dealers. Please go to HyundaiThetaEngineSettlement.com for full details. In addition, customer questions can also be directed to 1-866-944-7620 (Monday to Friday 7am-5pm PST).
20-01-004H-1
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
Campaign T3G Dea
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedures on TSB #20-01-004H-1 (supersedes TSB #20-01-004H) to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-AT-017H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 4. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Reverse and Drive
20-AT-018H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 3. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Drive and Reverse
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-014H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-AT-015H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the oil pressure harness.
20-AT-011H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-AT-012H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a (Check Engine Light on) and one or more of the DTC listed below, follow the repair procedure and replace the input/output speed sensor and oil pressure harness.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-EE-002H(1)
Service Bulletin/Repair Instructions
This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.
Campaign T3G DBP
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedures on TSB #20-01-004H (supersedes TSB #19-01-006H-4) rotate the crankshaft, perform the bearing inspection (if crankshaft does rotate) and/or replace the engine based on the crankshaft/bearing inspection results.
20-AT-007H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-01-004H - The
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-006H
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
Campaign 953 Dea
Service Bulletin/Repair Instructions
Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P1326 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-BE-001H
Service Bulletin/Repair Instructions
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-AT-001H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-021H-1
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-01-002H-4
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
19-01-005H-1
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
19-01-006H-4
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.
19-BE-015H-1
Service Bulletin/Repair Instructions
This bulletin contains information regarding the clock display on certain Navigation (AVN 4.0) head units. This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-AT-016H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
19-BR-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
19-BR-001H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
19-AT-012H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-BE-009H
Service Bulletin/Repair Instructions
This bulletin provides information for troubleshooting of the Blind-Spot Collision Warning (BCW/BSD) system whenever it exhibits Diagnostic Trouble Code (DTC) C120B/D or C160A.
19-AT-010H
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer pressure data to the ECU/TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality.
19-01-006H-2
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
19-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
DTC P1326 from 9
Service Bulletin/Repair Instructions
Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L engines that may experience the Check Engine warning lamp illuminated with DTC P1326.
Dealer Best Prac
Service Bulletin/Repair Instructions
Hyundai has refined the engine inspection for vehicles that experienced the Check Engine light with DTC P132600 to eliminate the interference caused by the wiring harness. As a result, we need the vehicles currently waiting for an engine replacement to be re-tested with the new software update using the GDS-mobile.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
Campaign 953 ECM
Service Bulletin/Repair Instructions
Hyundai has launched a Product Improvement Campaign to perform a knock sensor software update on applicable vehicles.
19-BE-004H
Service Bulletin/Repair Instructions
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
Campaign T3G - S
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to update the display audio software on certain 2019 Veloster vehicles. Service Campaign T3Q provides a procedure to update the display audio software for blank home screen.
19-FL-001H
Service Bulletin/Repair Instructions
In a gasoline direct injection (GDI) engine, highly pressurized gasoline is injected via a common rail fuel line and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-point fuel injection (MPI) engine, relatively low pressure gasoline is injected into the intake port of each cylinder. Due to high fuel pressures in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specification for the GDI fuel system components.
19-01-005H
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
19-01-006H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
953 Dealer Best
Service Bulletin/Repair Instructions
Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P132600 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.
T3G Dealer Best
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure on TSB #19-01-006H (supersedes TSB# 18-01-032-2) to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
19-01-002H-1
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
5NP-H9R6R-02
Service Bulletin/Repair Instructions
The software update installs a newly developed Knock Sensor Detection System (KSDS) that detects vibrations indicating the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM. The update will be done free of charge to customers and will only involve the addition of the KSDS software update.
5NP-E8E9D-02
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
5NP-Y4N3B-08
Service Bulletin/Repair Instructions
This bulletin describes the procedure to diagnose the vehicle?s D-Audio unit as a result of the inability to set the clock or view it on the top of the screen.
5NP-C5F9C-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a Check Engine light on and one or more of the DTC listed below, follow the repair procedure and replace the oil pressure harness.
5NP-P4Y7D-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine Light on? and one or more of the DTC listed below, follow the repair procedure and replace the input/output speed sensor and oil pressure harness.
5NP-M5G2M-08
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a complaint of ?Check Engine Light on? and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
5NP-G7C2D-06
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle?s display audio radio unit needs to be replaced as a result of the clock time inaccuracy (i.e. Resets overnight, loses/gains time).
5NP-F6W6P-05
Service Bulletin/Repair Instructions
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition.
5NP-P5L7D-05
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time.
5NP-G7W3S-05
Service Bulletin/Repair Instructions
If a vehicle exhibits a harsh and/or delayed shift, follow the Service Procedure below to measure the shift engagement time.
5NP-A4C8N-03
Service Bulletin/Repair Instructions
This TSB provides information on the headlight pattern changes on certain 2018 MY Sonata (LFa), Elantra (ADa)(AD), Elantra GT (PD), Santa Fe Sport (AN), and Santa Fe (NC).
5NP-F8K5A-02
Service Bulletin/Repair Instructions
Hyundai Motor America is adding additional models to Service Campaign T2M. Service campaign T2M provides a service procedure to replace the inhibitor switch on certain 2017-18 Santa Fe Sport, 2017 Santa Fe, 2017-18 Tucson, 2017 Azera, 2017 Sonata, Sonata Hybrid & Plug-in.
5NP-G7B2Q-02
Service Bulletin/Repair Instructions
This bulletin describes the service procedure to replace the inhibitor switch. A possible symptom is Diagnostic Trouble Code P0705 (Transmission Range Sensor Circuit).
5NP-T5B2D-02
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle?s head unit needs to be replaced as a result of the system frequently losing a Bluetooth connection with Apple iPhone devices.
5NP-G8S6L-01
Service Bulletin/Repair Instructions
This bulletin describes the procedure to determine if the vehicle's navigation unit needs to be replaced as a result of the inability to set the clock or view it on the top of the screen.
5NP-Q9G9X-12
Service Bulletin/Repair Instructions
This bulletin describes the service procedure to replace the inhibitor switch. A possible symptom is Diagnostic Trouble Code P0705 (Transmission Range Sensor Circuit).
5NP-Y3H5F-12
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to replace the inhibitor switch on certain 2017 Year Sonata, & 2017-18 Santa Fe Sport. Service Campaign T2M provides a service procedure to replace the inhibitor switch.
5NP-D4K7P-12
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to replace the gear indicator lens cover on certain 2017-18 model years Santa Fe and Santa Fe Sport vehicles. Service Campaign T2L provides a service procedure to replace the gear indicator lens cover.
5NP-F8W2R-12
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to replace the gear indicator lens cover on certain 2017-18 model years Santa Fe and Santa Fe Sport vehicles. Service Campaign T2L provides a service procedure to replace the gear indicator lens cover.
5NP-A2D2E-12
Service Bulletin/Repair Instructions
This bulletin describes the procedure to update the Traction Control System (TCS) logic on some 2017-2018MY Santa Fe Sport (AN) 2.0T and Santa Fe (NC) 3.3L vehicles. This update helps reduce unnecessary TCS engagement during low speed / dry road acceleration.
5NP-V3F8T-09
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.