Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
Z01 Letter
Warranty Program/Extension
Certain 2012 – 2017 model year Accent, 2012 – 2017 model year Azera, 2013 – 2018 model year Santa Fe Sport, 2013 – 2019 model year Santa Fe, and 2012 – 2017 model year Veloster vehicles may exhibit an intermittent airbag warning light and diagnostic trouble codes (DTCs) may be set. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the Occupant Classification System (OCS)/Occupant Detection System (ODS) under these conditions has been extended to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.
26-01-013H-2 DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
26-01-013H-2 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
9C2 060518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
9C2 DCS 260518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
26-BD-002H DN
Warranty Program/Extension
Some Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.
26-BD-002H TSB
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners. The warranty extension does not apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer or has a branded or similar title under any state’s law.
9C2 OL
Service Campaign
Certain 2019 – 2020 model year Santa Fe, 2017 – 2018 model year Santa Fe Sport, 2015 – 2019 model year Sonata, and 2018 – 2021 model year Tucson vehicles may exhibit elevated engine-out emissions. Hyundai is conducting a service campaign to update the Engine Control Module (ECM) Software for vehicles equipped with the (2.4 GDI) Theta II engine to improve engine combustion and fuel trim adaptations.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
9C2 Susp DCS
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
9C2 Susp DN
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
26-01-013H-1 DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H-1 DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
26-01-013H-1 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
26-01-013H TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
P33 OL
Other
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-087H-1 DCS
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 25-01-087H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-087H-1 DN
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
25-01-087H-1 TSB
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-089H DCS
Other
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
Other
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
Other
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-01-087H DCS
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 25-01-087H provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-087H DN
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-BD-004H OL
Warranty Program/Extension
Certain 2015 – 2018 model year Elantra, 2015 – 2019 model year Sonata, 2017 – 2021 model year Tucson, 2017 – 2018 model year Santa Fe Sport, 2019 model year Santa Fe, 2021 – 2023 model year Santa Fe Hybrid, and 2020 – 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H EM
Warranty Program/Extension
Some vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H DN
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any state’s law.
25-BD-004H TSB
Warranty Program/Extension
Description: Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any state’s law.
25-01-024H EM
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.
25-01-024H TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
TXX8 OL
Warranty Program/Extension
Certain 2013 – 2019 model year Santa Fe/Santa Fe XL vehicles equipped with 3.3L Lambda II GDI engines may experience abnormal engine noise or engine damage. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for certain engine repairs and/or replacement related to eligible conditions has been extended to 15 years/150,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Eligibility for this warranty coverage is determined upon an inspection of the vehicle’s engine.
24-01-050H-1
Service Campaign
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-050H
Service Bulletin/Repair Instructions
This bulletin provides instructions to update the 4th generation AVN head unit software to ensure the SIM Over The Air function for the Bluelink service is operating properly.
24-01-009H-1
Service Campaign
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-014H-5
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-AT-003H-1
Service Bulletin/Repair Instructions
If you are servicing an 8-speed vehicle with a âCheck Engineâ light on and one or more of the DTC listed, follow the service procedure and replace the related solenoid and harness.
23-BE-010H
Service Bulletin/Repair Instructions
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
23-BE-007H
Service Bulletin/Repair Instructions
This Service Information bulletin provides information on how to update the Apple Carplay software from Hyundaiâs Navigation Updates page. The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.
23-AT-005H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to update the TCU to revise the logic for P0741 (Torque converter clutch circuit).
23-01-014H-4
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-AT-003H
Service Bulletin/Repair Instructions
If you are servicing an 8-speed vehicle with a âCheck Engineâ light on and one or more of the DTC listed, follow the service procedure and replace the related solenoid and harness.
23-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information related to the ECU software update for improvement of: - ISG operation in relation to the battery SOH (State Of Health) condition will be removed - ISG engagement with satisfied battery SOC (State Of Charge) will remain
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
23-BE-001H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to diagnose and repair tire pressure monitoring system (TPMS) DTC(s) on some 19MY and newer Santa Fe (TMA), 2021MY and newer Santa Fe Hybrid (TM HEV), 2022MY and newer Santa Fe Plug-In Hybrid (TM PHEV), and 2019MY and newer Palisade (LX2) vehicles equipped with surround view monitoring (SVM) system.
22-SS-003H-1
Service Bulletin/Repair Instructions
This bulletin describes the procedure to refinish 19â wheels equipped on some 19-20MY Santa Fe (TMA) 2.0T vehicles with peeling clear coat.
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
218/231 amend
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
22-AT-006H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related input/output speed sensor and harness.
22-AT-005H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and valve body harness.
22-01-033H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
22-EM-001H-1
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
22-EM-002H-1
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Warranty coverage is valid for original and subsequent owners.
DBPT3G
Service Bulletin/Repair Instructions
Certain vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit abnormal noise or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.
22-ST-005H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.
22-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Electric Waste Gate Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ⢠Check Engine Light illumination with EWGA related DTC. ⢠Intermittently high/low turbocharger boost pressures. ⢠Abnormal noise from the turbocharger.
22-EM-001H
Service Bulletin/Repair Instructions
The warranty coverage for engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
TXXI DBP
Service Bulletin/Repair Instructions
The warranty coverage for certain Theta II engine long block repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.
21-01-066H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L T-GDI and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
T3GDBP20211103
Service Bulletin/Repair Instructions
Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P1326.
21-ST-003H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing
21-EM-009H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Electric Waste Gate Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ⢠Check Engine Light illumination with EWGA related DTC. ⢠Intermittently high/low turbocharger boost pressures. ⢠Abnormal noise from the turbocharger. ⢠Reduced engine power.
21-EM-008H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Variable Charge Motion Controllers (VCM) equipped in the applicable vehicles listed below. This bulletin also provides information on the use of the Service Kit for 2.4L equipped engines, which enables replacing the VCM Lever Arm without replacing the complete Intake Manifold Assembly. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ï Check Engine Light illumination with VCM related DTC. ï Unstable engine RPM and reduced engine power. ï Abnormal noise from the intake manifold whenever engine RPM is raised from idle speed.
21-01-037H-1
Service Bulletin/Repair Instructions
2013-2019MY Santa Fe/Santa Fe XL (NC) Onboard Refueling Vapor Recovery (ORVR) system may exceed its capacity in certain situations. This bulletin provides the procedure to install an Auxiliary Canister and kit to increase the ORVR system capacity. There are no drivability concerns associated with the condition.
21-BE-008H
Service Bulletin/Repair Instructions
Certain vehicles may experience 504 Time Out errors when using the Blue Link Mobile App. When asked to provide Modem Information (IMEI/USIM), the Head Unit (HU) displays all zeros. This bulletin describes the procedure to update the Head Unit Software to correct this condition.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-BE-006H
Service Bulletin/Repair Instructions
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with the front multifunction camera may exhibit one or more of the following warnings on the instrument cluster; Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB). This bulletin describes the procedure to replace the front camera/ multi-function camera.
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
21-01-002H
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block for engine repairs or replacement related to connecting rod bearing damage as described in Campaign T3G (Seized and/or BCT No Pass Result Only) has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Please refer to TSB # 20-01-024H-2 (or latest revision) for applicable part numbers and labor ops.
20-01-004H-3
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H-2
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
20-BD-016H-1
Service Bulletin/Repair Instructions
Certain Santa Fe (TMa) and Palisade (LX2) vehicles may exhibit noise coming from the second row seat track. This bulletin provides information on how to inspect and if necessary repair the condition.
20-FL-011H
Service Bulletin/Repair Instructions
This bulletin provides information related to an Electronic Control Module (ECM) software update which revises DTC P00D2: Oxygen Sensor Heater Control Circuit Range/Performance Bank 1 diagnostic logic.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-01-004H-2
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H-1
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
20-AT-005H-1
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and valve body harness.
20-01-039H
Service Bulletin/Repair Instructions
This bulletin provides information and procedures for collecting OBD âIn Use Monitor Performance Ratioâ (IUMPR) data on certain 2019-2021MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board).
20-BE-006H-1
Service Bulletin/Repair Instructions
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with the front multifunction camera may exhibit one or more of the following warnings on the instrument cluster; Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB). This bulletin describes the procedure to replace the front camera/ multi-function camera.
20-01-037H
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
20-AT-022H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to update the TCU for a shift flare and shock on reacceleration when driving in Sport Mode.
20-ST-001H-2
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-003H-1
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-01-022H-2
Service Bulletin/Repair Instructions
Some 2019-2020 Nexo (FE), and 2020 Palisade (LX2) vehicles equipped with the power tailgate may not operate. This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.
20-AT-020H
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the transmission learning time and improve the shift quality.
20-ST-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-003H
Service Bulletin/Repair Instructions
Certain vehicles may develop a bearing noise within the Motor Driven Power Steering (MDPS) column worm shaft assembly. If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
TXXI Dealer Best
Service Bulletin/Repair Instructions
This Dealer Best Practice intends to inform dealers of a proposed settlement (âSettlementâ) for a class action lawsuit filed against Hyundai Motor America (âHMAâ). Beginning in July 2020, customers affected by the proposed settlement will begin becoming informed of the settlement by mailed notice and email, and they may direct questions to dealers. Please go to HyundaiThetaEngineSettlement.com for full details. In addition, customer questions can also be directed to 1-866-944-7620 (Monday to Friday 7am-5pm PST).
20-01-022H-1
Service Bulletin/Repair Instructions
Some 2019 - 2020 Nexo (FE), 2020 Palisade (LX2), and 2019 - 2020 Santa Fe (TM) vehicles equipped with the power tailgate may not operate. This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.
Campaign T4X Dea
Service Bulletin/Repair Instructions
Certain 2019-2020 Nexo (FE), 2020 Palisade (LX2), and 2019 - 2020 Santa Fe (TM) vehicles equipped with the power tailgate may experience a nonoperational condition. This campaign provides service procedures to inspect and when necessary, perform the power tailgate spindle wire harness revision.
20-01-004H-1
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-024H
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.
Campaign T3G Dea
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedures on TSB #20-01-004H-1 (supersedes TSB #20-01-004H) to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-BD-016H
Service Bulletin/Repair Instructions
Certain Santa Fe (TM) and Palisade (LX2) vehicles may exhibit noise coming from the second row seat track. This bulletin provides information on how to inspect and if necessary repair the condition.
20-AT-017H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 4. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Reverse and Drive
20-AT-019H
Service Bulletin/Repair Instructions
If you are servicing any of the vehicles listed below with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time.
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-014H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-BE-006H
Service Bulletin/Repair Instructions
Certain 2019-2020MY Santa Fe and 2018-2020MY Elantra equipped with front camera/multi-function camera may exhibit a series of Lane Keep Assist System (LKAS), Front Collision Avoidance Assist (FCA), High Beam Assist (HBA), Smart Cruise Control (SCC), and Autonomous Emergency Braking (AEB) warnings and function conditions on the instrument cluster. This bulletin describes the procedure to replace the front camera/ multi-function camera.
20-BE-005H
Service Bulletin/Repair Instructions
This bulletin provides information on how to properly replace the Drive Unit Power Tailgate Assembly (LH or RH or LH and RH) when the tailgate exhibits difficulty opening/closing and/or noisy operation.
20-EE-005H
Service Bulletin/Repair Instructions
Hyundai vehicles are equipped with Dark Current Control logic to help reduce amperage draw amount and conserve Battery State of Charge (SOC%). A selected Dark Current Control Mode will function when the vehicle is in the key off state, and will not affect vehicle functionality or performance.
20-AT-011H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-EE-002H(1)
Service Bulletin/Repair Instructions
This bulletin describes the mandatory procedure to submit battery test data electronically for battery warranty claims by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.
20 AT-009H
Service Bulletin/Repair Instructions
If you are servicing a 2019 Santa Fe (2.0T) with a harsh 2-3 or 3-4 upshift when cold, follow the Service Procedure below.
Campaign T3G DBP
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedures on TSB #20-01-004H (supersedes TSB #19-01-006H-4) rotate the crankshaft, perform the bearing inspection (if crankshaft does rotate) and/or replace the engine based on the crankshaft/bearing inspection results.
20-AT-008H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-01-004H - The
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.
20-01-006H
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
Campaign 953 Dea
Service Bulletin/Repair Instructions
Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P1326 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-AT-003H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a Check Engine light on and one or more of the DTC listed below, follow the repair procedure and replace the related input/output speed sensor and oil pressure harness.
20-AT-004H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a Check Engine light on and one or more of the DTC listed below, follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.
20-AT-005H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a Check Engine light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-BE-001H
Service Bulletin/Repair Instructions
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-AT-001H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-01-042H
Service Bulletin/Repair Instructions
This bulletin provides information and procedures for collecting OBD ?In Use Monitor Performance Ratio? (IUMPR) data on certain 2019-2020MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board). Data is no longer submitted to Hyundai by datasheet and dealer email. Data is sent electronically by GDS when the procedure of this bulletin is followed.
19-AT-021H-1
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-01-002H-4
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
19-01-005H-1
Service Bulletin/Repair Instructions
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
19-01-006H-4
Service Bulletin/Repair Instructions
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.
19-BD-008H
Service Bulletin/Repair Instructions
This bulletin provides instructions on the replacement of a cup holder with retaining tabs which cannot stabilize a cup due to inner O-ring displacement.
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-EM-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines.
19-AT-019H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.
19-AT-017H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
19-AT-018H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related input/output speed sensor and oil pressure harness.
19-BR-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
19-AT-013H
Service Bulletin/Repair Instructions
If you are servicing a 2019 Santa Fe (2.0T) with a harsh 2-3 or 3-4 upshift when cold, follow the Service Procedure below.
19-BR-001H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
19-AT-012H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-BE-008H
Service Bulletin/Repair Instructions
This bulletin provides information for replacement of the Blind-Spot Collision Warning (BCW) module. Whenever the left or right side BCW module is being replaced, it is required to perform the variant coding procedure. If the variant coding procedure is not performed, a DTC C1743 (S/W mismatch) will be triggered.
19-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-BE-004H
Service Bulletin/Repair Instructions
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
19-FL-002H
Service Bulletin/Repair Instructions
This bulletin describes the Santa Fe (TM) Idle Stop and Go (ISG) system operations and battery sensor recalibration procedure. Refer to applicable Work Shop Manual and Owner?s Manual for additional information
19-FL-001H
Service Bulletin/Repair Instructions
In a gasoline direct injection (GDI) engine, highly pressurized gasoline is injected via a common rail fuel line and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-point fuel injection (MPI) engine, relatively low pressure gasoline is injected into the intake port of each cylinder. Due to high fuel pressures in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specification for the GDI fuel system components.
5NP-T3D4X-01
Service Bulletin/Repair Instructions
This bulletin provides information related to the Engine Control Module (ECM) and Electronic Stability Control (ESC) software updates for certain 2019MY Santa Fe (TM) equipped with 2.4L engine. The ECM update is revised for starting performance and Idle Stop & Go (ISG) control logic. In addition, the ESC update is revised for hold timing of Hill-start Assist Control (HAC) function to optimized ISG operation.
5NP-X7C8Z-01
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to update the ECM & ESC on certain 2019 model year Santa Fe 2.4L vehicles. Service Campaign T3M provides a service procedure to update the ECM & ESC software.
5NP-T3A9N-12
Service Bulletin/Repair Instructions
The vehicles listed below are equipped with an 8-speed front-wheel drive transmission. Do not replace the transmission for any of the solenoid DTC listed below. Instead, follow the Service Procedure on Page 2 and replace the related part.
5NP-Z4J8U-12
Service Bulletin/Repair Instructions
This bulletin provides a procedure to transfer pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the transmission learning time and improve the shift quality.