Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
26-01-033H DN
Warranty Program/Extension
This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.
26-01-033H TSB
Warranty Program/Extension
This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H-2 (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
24-01-068H
Service Campaign
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
24-AT-002H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-012H
Service Bulletin/Repair Instructions
In some areas, a vehicleâs underbody may exhibit corrosion due to road salt usage. As a preventative measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the bottom exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain Tucson (LM) vehicles.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
22-01-023H-2
Service Bulletin/Repair Instructions
A class action lawsuit against Hyundai Motor America (âHMAâ) alleges that certain Hyundai vehicles (âClass Vehiclesâ) were manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the âSettlementâ) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-01-024H-2
Service Bulletin/Repair Instructions
OP CODE/PART NUMBER (REFERENCE GUIDE FOR SERVICE CAMPAIGN T6G)
22-EM-006H-2
Service Bulletin/Repair Instructions
The warranty coverage for engine repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
22-01-023H-1
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-028H-1
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
22-EM-006H-1
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
DBP966
Service Bulletin/Repair Instructions
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
DBPT6G
Service Bulletin/Repair Instructions
Certain vehicles that have completed Service Campaign 966 may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-023H
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-028H
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-023H-4
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-EM-005H-1
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
21-01-023H-3
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-023H-2
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
966DBP
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-ST-001H-2
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
20-AT-017H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 4. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Reverse and Drive
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-014H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-AT-011H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-01-012H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to inspect the evaporative systemâs existing canister for loose charcoal, and if confirmed the new Auxiliary Canister Kit of this bulletin will be installed to improve evaporative system performance. The existing canister will not be replaced.
Campaign 958 Dea
Service Bulletin/Repair Instructions
Hyundai is conducting a Service Campaign to inspect the existing charcoal canister for loose charcoal, and if confirmed a new auxiliary canister kit will be installed. The affected vehicles include: ⢠All 2010-2015 Tucson (LM) 2.4L Engine with ULEV emissions.
20-AT-008H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-BE-001H
Service Bulletin/Repair Instructions
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-AT-001H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-021H-1
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-BD-007H
Service Bulletin/Repair Instructions
The warranty coverage for the panoramic sunroof moving glass has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
19-AT-015H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness
19-AT-012H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
5NP-F6W6P-05
Service Bulletin/Repair Instructions
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition.
5NP-P5L7D-05
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time.
5NP-V3F8T-09
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
5NP-H2S7R-12
Service Bulletin/Repair Instructions
In some areas, a vehicle?s underbody may exhibit corrosion due to road salt usage. As a precautionary measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the bottom exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain Tucson (LM) vehicles.
5NP-U4R7N-11
Service Bulletin/Repair Instructions
SOME TUCSON (LM) AND SANTA FE SPORT (AN) MAY EXPERIENCE A ROUGH IDLE IN DRIVE AFTER DECELERATING TO A STOP WHEN NEUTRAL CONTROL IS ENABLED. THIS BULLETIN PROVIDES A DIAGNOSIS AND REPAIR PROCEDURE FOR THIS CONDITION.
5NP-M6C8D-10
Service Bulletin/Repair Instructions
THIS BULLETIN DESCRIBES THE PROCEDURE TO VERIFY THAT THE FUSE AND JUMPER SETTINGS FOR THE REMOTE ENGINE START CONTROL MODULE ARE SET FOR THE APPLICABLE VEHICLE, AND IF NECESSARY, HOW TO MAKE ADJUSTMENTS TO THESE SETTINGS.
5NP-S9D9P-10
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES INFORMATION ON COMPONENTS, ATTRIBUTES, AND PRECAUTIONS OF THE 7-SPEED DRY-TYPE DUAL CLUTCH TRANSMISSION (DCT).
5NP-B6E2P-10
Service Bulletin/Repair Instructions
THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE
5NP-Q7S7E-09
Service Bulletin/Repair Instructions
THE SHIFT LEVER ON SOME 6-SPEED VEHICLES MAY INTERMITTENTLY NOT SHIFT OUT OF PARK. THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.
5NP-E2D7G-09
Service Bulletin/Repair Instructions
THE FOLLOWING VEHICLES ARE EQUIPPED WITH A 6-SPEED AUTOMATIC TRANSMISSION. THE ATF LEVEL MUST BE CHECKED BY THE FOLLOWING PROCEDURE.
16-AT-004
Service Bulletin/Repair Instructions
AUTOMATIC TRANSAXLE (6-SPEED) ATM FLUID LEVEL CHECK Description: The following vehicles are equipped with a 6-speed automatic transmission. The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.
TSB-15-TC-001
Service Bulletin/Repair Instructions
HYUNDAI: PROCEDURE INFORMATION FOR REPAIR AND REPLACEMENT OF HARNESS 4WD AND ACTUATOR MOTOR COUPLING AND COMPONENTS FOR COUPLING ASSEMBLY CAN BE SEPARATELY REPLACED AS SERVICE PARTS. MODEL 2010-15 TUCSON. *PE
SC-932
Service Bulletin/Repair Instructions
HYUNDAI: ON CERTAIN MODEL VEHICLES, A REQUIRED INSPECTION OF THE FRONT AXLE SHAFTS AND MAY BE REPLACEMENT OF FRONT AXLE SHAFT, IF NEEDED. MODEL 2010-14 TUCSON. *PE
14-FL-007
Service Bulletin/Repair Instructions
HYUNDAI 2010-2011 MY TUCSON 2.4L: PROVIDED INFORMATION REGARDING THE ECM SOFTWARE UPDATE. CHECK ENGINE LIGHT SHOWS WITH CERTAIN DTC'S : P0300-P0304. *LJ
14-AT-013
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
14-AT-012
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
14-AT-010
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
14-AT-003
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-AT-012-2
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-AT-014-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
FIR-0909
Service Bulletin/Repair Instructions
HYUNDAI: PROCEDURE INFORMATION PROVIDED ON SYMPTOMS AND INSPECTION OF FUEL LEVEL SENDER WITH CERTAIN SYMPTOMS. MODELS 2006-2011 SONATA, 2012 GENESIS, 2010 TUCSON. *PE
13-AT-012-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-AT-012
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-AT-014
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-AT-009
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-13-FL-003
Service Bulletin/Repair Instructions
HYUNDAI: INFORMATION REGARDING THE INSPECTION PROCEDURE FOR FUEL LEVEL SENDER AND SYMPTOMS OF CHECK ENGINE LIGHT ON, ERRATIC OR UNRESPONSIVE FUEL GAUGE OR FUEL GAUGE DOES NOT REACH FULL LEVEL AFTER FILLING UP. MODELS 2012-2014 GENESIS, 2006-2014 SONATA, 2010-2014 TUCSON. *PE
TSB-13-AT-008
Service Bulletin/Repair Instructions
HYUNDAI: INFORMATION HAS BEEN PROVIDED REGARDING PROCEDURE IN REPAIRING AND REPLACING RELATED PART TO TRANSMISSION SOLENOID DTC FOR CERTAIN VEHICLES. MODELS 2010-2013 TUCSON, SANTA FE, 2011-2013 SONATA, ELANTRA, AZERA, 2012-2013 ACCENT, 2013 VELOSTER. *PE
TSB-13-FL-002
Service Bulletin/Repair Instructions
HYUNDAI: THE THROTTLE CONTROL (ETC) BODY, ON SOME VEHIICLES, NEEDS TO BE CLEANED AND PROCEDURAL INFORMATION IS BEING PROVIDED, DUE TO DEPOSITS FOUND AT VALVE-TO-BORE INTERFACE. MODELS 2011-2013 ELANTRA, 2010-2013 GENESIS COUPE, 2010-2013 SANTA FE, 2006-2013 SONATA, 2010-2013 TUCSON. *PE
13-AT-006
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-13-FL-001
Service Bulletin/Repair Instructions
HYUNDAI: DUE TO AN ERROR IN THE INTERNAL CONTROL MODULE READ ONLY MEMORY, INFORMATION IS PROVIDED REGARDING THE REPLACING OF THE PCM AND A POSSIBLE WARRANTY CLAIM. MODELS 2011-2013 ELANTRA, 2010-2013 GENESIS COUPE, 2010-2013 SANTA FE, 2006-2013 SONATA, 2010-2013 TUCSON. *PE
12-AT-009-4
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
12-AT-016-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
12-AT-021-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-12-01-021
Service Bulletin/Repair Instructions
HYUNDAI: INFORMATION PROVIDED REGARDING INSTALLATION OF INHIBITOR SWITCH BRACKET TO PREVENT SHOCK WHEN SHIFTING VEHICLE TO DRIVE OR REVERSE. MODELS 2010-11 TUCSON AND 2009-10 SONATA. *PE
12-AT-009-2
Service Bulletin/Repair Instructions
HYUNDAI: ATM INPUT AND OUTPUT SPEED SENSOR DTC P0717, P0721 AND P0722. DO NOT REPLACE TRANSMISSION FOR THE DTC. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE RELATED PART. ALSO INCLUDED MODEL AZERA MODEL YEAR 2012. *JS
12-AT-012
Service Bulletin/Repair Instructions
HYUNDAI: AUTOMATIC TRANSAXLE HARSH AND/OR DELAYED SHIFT- GDS ANALYSIS. ALSO INCLUDED MODEL ELANTRA MODEL YEAR 2013. *JS
TSB-11-AT-009
Service Bulletin/Repair Instructions
HYUNDAI: OPERATION OF THE TRANSMISSION SOLENOID MAY LEAD TO CHECK ENGINE LIGHT, TRANSAXLE HELD IN 4TH GEAR SAFE, AND DIAGNOSTIC TROUBLE CODES. *RM
10-AT-005
Service Bulletin/Repair Instructions
HYUNDAI: CHECK ENGINE LIGHT ON, TRANSAXLE HELD IN THIRD GEAR, AND TROUBLE CODES STORED. THIS IS CAUSED BY INCORRECT INPUT AND OUTPUT SPEED SENSORS. *RM
TSB-10AT003-1
Service Bulletin/Repair Instructions
HYUNDAI: AUTOMATIC TRANSMISSION SOLENOID DTC P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773 AND P2709. INCORRECT OPERATION OF THE TRANSMISSION SOLENOIDS MAY RESULT IN THE FOLLOWING: CHECK ENGINE LIGHT ILLUMINATED; TRANSAXLE HELD IN 4TH GEAR FAIL SAFE. *PE UPDATED 6/10/11. *PE
TSB-10B005
Service Bulletin/Repair Instructions
HYUNDAI: SMART JUNCTION BOX REPLACEMENT. IF A VEHICLE EXHIBITS ALL OF THE FOLLOWING SIX CONDITIONS, REPLACE THE SMART JUNCTION BOX-REAR TAILGATE RELEASE BUTTON INOPERABLE; KEY REMINDER INOPERABLE; DOOR AJAR WARNING LIGHT IN INSTRUMENT CLUSTER ILLUMINATES WITH ALL DOORS CLOSED; DOME LAMP REMAINS ON WILL DOORS CLOSED; CENTRAL DOOR LOCK SWITCH INOPERABLE; AND AUTO DOOR LOCK FUNCTION INOPERABLE. *PE
TSB-10-GI-001
Service Bulletin/Repair Instructions
HYUNDAI: LABEL REQUIREMENTS FOR VEHICLE LOADING TO COMPLY WITH FMVSS 110. EFFECTIVE 6/2/08, FMVSS 110 (FMVSS 110) SETS A THRESHOLD FOR CORRECTING LOAD CAPACITY INFORMATION INDICATED ON TIRE PLACARDS WHEN VEHICLE WEIGHT HAS BEEN INCREASED BEFORE RETAIL SALE. ALL MODELS INCLUDED AFTER 6/2/08. *PE
TSB-10-AT-006
Service Bulletin/Repair Instructions
HYUNDAI: A 6 SPEED AUTOMATIC TRANSAXLE WITH A HARSH AND/OR DELAYED SHIFT; GDS ANALYSIS. *PE
TSB-09-BE-028
Service Bulletin/Repair Instructions
HYUNDAI: SRS CONTROL MODULE ROLLOVER SENSOR. A ROLLOVER SENSOR HAS BEEN INCORPORATED INTO THE SRS CONTROL MODULE (SRSCM) BEGINNING WITH THE 2010 MODEL YEAR SANTA FE AND TUCSON. THE ROLLOVER SENSOR DETERMINES IF IT IS NECESSARY TO DEPLOY SIDE AIR BAGS, CURTAIN AIR BAGS AND SEAT BELT PRETENSIONERS IF A VEHICLE ROLLOVER OCCURS. *PE