Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
Z05 OL
Warranty Program/Extension
Certain vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
26-01-013H-2 DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
26-01-013H-2 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
9C2 060518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
9C2 DCS 260518
Service Campaign
Following completion of Service Campaign 9C2 (Theta II Emissions Improvement), certain vehicles may exhibit a brief hesitation or rough shifting condition during cold start operation. If present, this condition is expected to occur only within approximately the first 1-3 minutes after engine start, while the catalyst is reaching its normal operating temperature.
26-BD-002H DN
Warranty Program/Extension
Some Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.
26-BD-002H TSB
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners. The warranty extension does not apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer or has a branded or similar title under any state’s law.
9C2 OL
Service Campaign
Certain 2019 – 2020 model year Santa Fe, 2017 – 2018 model year Santa Fe Sport, 2015 – 2019 model year Sonata, and 2018 – 2021 model year Tucson vehicles may exhibit elevated engine-out emissions. Hyundai is conducting a service campaign to update the Engine Control Module (ECM) Software for vehicles equipped with the (2.4 GDI) Theta II engine to improve engine combustion and fuel trim adaptations.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
9C2 Susp DCS
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
9C2 Susp DN
Service Campaign
Hyundai Motor America is currently investigating an ongoing issue with software GDS event #1383 related to 2015MY Sonata (LFA) 2.4L vehicles. The matter is currently being investigated for a resolution as soon as possible. The impacted vehicles related to this event will not show open on the VIN in WebDCS while this event is under suspension.
26-01-033H DN
Warranty Program/Extension
This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.
26-01-033H TSB
Warranty Program/Extension
This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H-2 (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.
26-01-013H-1 DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H-1 TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DCS
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H provides instructions for updating the Engine Control Module (ECM) to address this condition.
26-01-013H DN
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
26-01-013H TSB
Service Campaign
Certain Santa Fe (TMA), Santa Fe Sport (AN), Sonata (LFA), and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
P33 OL
Other
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-087H-1 DCS
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 25-01-087H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-087H-1 DN
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.
25-01-087H-1 TSB
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-089H DCS
Other
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
Other
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
Other
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-01-087H DCS
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 25-01-087H provides instructions for updating the Engine Control Module (ECM) to address this condition.
25-01-087H DN
Service Campaign
Certain Santa Fe (TMA), Sonata (LFA) and Tucson (TL) vehicles equipped with Theta II engines may exhibit elevated engine-out emissions.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
25-BD-004H OL
Warranty Program/Extension
Certain 2015 – 2018 model year Elantra, 2015 – 2019 model year Sonata, 2017 – 2021 model year Tucson, 2017 – 2018 model year Santa Fe Sport, 2019 model year Santa Fe, 2021 – 2023 model year Santa Fe Hybrid, and 2020 – 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H EM
Warranty Program/Extension
Some vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.
25-BD-004H DN
Warranty Program/Extension
Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any state’s law.
25-BD-004H TSB
Warranty Program/Extension
Description: Certain Hyundai vehicles with exterior white paint may exhibit peeling or bubbling on metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any state’s law.
25-01-024H-1 TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
25-01-024H EM
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.
25-01-024H TSB
Service Campaign
Some vehicles may exhibit a loss of connectivity or interruptions in the middle of using Bluelink Service functions. This may be due to an irregular disconnection on Verizon’s communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.
24-01-068H
Service Campaign
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
24-01-009H-1
Service Campaign
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-AT-002H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
24-EM-002H
Service Bulletin/Repair Instructions
Certain 2016-2021MY Tucson (TL) 2.0L vehicles may experience continued DTC P1326 after the ECU update has been performed per TSB 22-01-028H-1 (or later) âENGINE MONITORING LOGIC (SERVICE CAMPAIGN 966)â.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-014H-5
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-BE-010H
Service Bulletin/Repair Instructions
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
22-01-023H-2
Service Bulletin/Repair Instructions
A class action lawsuit against Hyundai Motor America (âHMAâ) alleges that certain Hyundai vehicles (âClass Vehiclesâ) were manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the âSettlementâ) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.
23-FL-002H-1
Service Bulletin/Repair Instructions
This bulletin provides the diagnostic procedure for the GDI injector(s) in certain 21-23MY Sonata, 21-22MY Santa Fe, certain 22MY Santa Cruz, and certain 21-23MY Tucson equipped with 2.5L GDI engines with one or more misfire DTC(s) due to internally leaking GDI injector(s)
23-01-014H-4
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-01-014H-3
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-FL-002H
Service Bulletin/Repair Instructions
This bulletin provides the diagnostic procedure for the GDI injector(s) in certain 21-23MY Sonata, 21-22MY Santa Fe, certain 22MY Santa Cruz, and certain MY21-23 Tucson equipped with 2.5L GDI engines with one or more misfire DTC(s) due to internally leaking GDI injector(s).
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
22-01-023H-1
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-028H-1
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
22-EM-006H-1
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
DBP966
Service Bulletin/Repair Instructions
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
DBPT6G
Service Bulletin/Repair Instructions
Certain vehicles that have completed Service Campaign 966 may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
21-AT-017H
Service Bulletin/Repair Instructions
: Certain vehicles equipped with 8-speed automatic transmission may experience an automatic transmission fluid (ATF) leak at the rear cover. This type of leak is caused by a porous casting on the rear cover of the transmission.
21-EM-008H
Service Bulletin/Repair Instructions
This bulletin provides additional service diagnostic information and repair procedures related to Variable Charge Motion Controllers (VCM) equipped in the applicable vehicles listed below. This bulletin also provides information on the use of the Service Kit for 2.4L equipped engines, which enables replacing the VCM Lever Arm without replacing the complete Intake Manifold Assembly. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: ï Check Engine Light illumination with VCM related DTC. ï Unstable engine RPM and reduced engine power. ï Abnormal noise from the intake manifold whenever engine RPM is raised from idle speed.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-GI-003H
Service Bulletin/Repair Instructions
This bulletin provides information on the Launch Quality Monitoring Process (LQMP) for the 2022MY Hyundai Tucson. After a new vehicle launch, Hyundai uses the LQMP to monitor all customer and dealer activities at a minimum of 100 days. The Tucson LQMP helps improve model vehicle quality, and allows Hyundai to proactively respond to the Voice of the Customer (VOC).
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
20-BE-014H
Service Bulletin/Repair Instructions
When using Wireless CarPlay, the system may intermittently auto disconnect. When Wireless CarPlay is disconnected, a pop up message âPhone Not Responding. Please reconnect it and try againâ will appear on the radio screen.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-01-039H
Service Bulletin/Repair Instructions
This bulletin provides information and procedures for collecting OBD âIn Use Monitor Performance Ratioâ (IUMPR) data on certain 2019-2021MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board).
20-ST-001H-2
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.