Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
Z01 Letter
Warranty Program/Extension
Certain 2012 – 2017 model year Accent, 2012 – 2017 model year Azera, 2013 – 2018 model year Santa Fe Sport, 2013 – 2019 model year Santa Fe, and 2012 – 2017 model year Veloster vehicles may exhibit an intermittent airbag warning light and diagnostic trouble codes (DTCs) may be set. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the Occupant Classification System (OCS)/Occupant Detection System (ODS) under these conditions has been extended to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.
26-BE-011H DN
Warranty Program/Extension
Some vehicles listed below may exhibit an intermittent airbag warning light and DTC(s) B1763 (OCS ECU Defect), and/or B1764 (OCS Mat Defect) may be stored. Hyundai is extending the warranty coverage of the sensor for the Occupant Classification System (OCS) / Occupant Detection System (ODS) to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Refer to the warranty and parts information outlined in this bulletin.
26-BE-011H TSB
Warranty Program/Extension
Some vehicles listed below may exhibit an intermittent airbag warning light and DTC(s) B1763 (OCS ECU Defect), and/or B1764 (OCS Mat Defect) may be stored. Hyundai is extending the warranty coverage of the sensor for the Occupant Classification System (OCS) / Occupant Detection System (ODS) to 18 years/unlimited mileage from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Refer to the warranty and parts information outlilned in this bulletin. This bulletin contains the procedure to inspect for the airbag warning light and DTC(s), replace the OCS (ODS) unit or wire harness, reset the OCS (ODS), and initialize the power seat module (if applicable). This TSB also contains the procedure to replace the OCS (ODS) mat if DTCs exist after replacement of the OCS (ODS) wire harness.
DTN DCS
Other
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.
DTN DL
Other
The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.
26-01-033H DN
Warranty Program/Extension
This TSB references the Op codes to use for claim submission and the Parts required based on the vehicle’s inspection results from TSB 22-01-023H (DTC P1326 – Engine Bearing Inspection/Engine Replacement) or the latest version.
P33 OL
Other
In response to this trend, we engineered a software upgrade that addresses the social media theft method and made it available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, we’ve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (“Subject Vehicle”) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed — if you request it — at no cost to you through an authorized Hyundai dealership.
25-01-089H DCS
Other
Upon customer's request ONLY, the Technical Service Bulletin (TSB) 25-01-089H provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).
25-01-089H DN
Other
In addition to the Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1), a zinc reinforced ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.
25-01-089H TSB
Other
This bulletin provides the service procedure for installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows.
25-BD-012H TSB
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
24-01-068H
Service Campaign
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
24-01-009H-1
Service Campaign
A class settlement against Hyundai Motor America (“HMA”) that had alleged that certain 2011 – 2022 model year Hyundai vehicles that were not equipped with an engine immobilizer (called the “Class Vehicles”) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional “turn-key-to-start” ignition systems.
24-AT-002H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2.
24-BD-001H
Service Bulletin/Repair Instructions
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.
24-01-009H
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.
23-01-014H-6
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-01-014H-5
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993), combined with an anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.
23-EM-005H
Service Bulletin/Repair Instructions
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.
23-BE-010H
Service Bulletin/Repair Instructions
Some models from service campaign 993 (IBU/BCM Software Update and Decals Application) equipped with the Hyundai OEM remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.
22-01-023H-2
Service Bulletin/Repair Instructions
A class action lawsuit against Hyundai Motor America (âHMAâ) alleges that certain Hyundai vehicles (âClass Vehiclesâ) were manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the âSettlementâ) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.
23-01-014H-4
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-BD-007H
Service Bulletin/Repair Instructions
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.
23-01-014H-3
Service Bulletin/Repair Instructions
Certain Hyundai vehicles may not be equipped with an immobilizer. This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.
23-01-014H-2
Service Bulletin/Repair Instructions
Hyundai has launched an anti-theft software upgrade and window decal campaign (Campaign 993) in response to an increase in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.
23-BD-002H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.
22-01-092H
Service Bulletin/Repair Instructions
In certain areas, a vehicleâs underbody may exhibit corrosion due to road-salt usage. As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain 2012 â 2017MY Velosters (FS).
22-01-024H-2
Service Bulletin/Repair Instructions
OP CODE/PART NUMBER (REFERENCE GUIDE FOR SERVICE CAMPAIGN T6G)
22-EM-006H-2
Service Bulletin/Repair Instructions
The warranty coverage for engine repair or replacement regarding engine damage or malfunction from connecting rod bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.
22-EM-010H
Service Bulletin/Repair Instructions
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement.
22-GI-006H
Service Bulletin/Repair Instructions
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.
22-01-023H-1
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-028H-1
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
22-EM-006H-1
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
DBP966
Service Bulletin/Repair Instructions
Hyundai is conducting a service campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
DBPT6G
Service Bulletin/Repair Instructions
Certain vehicles that have completed Service Campaign 966 may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-023H
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
22-01-028H
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-023H-4
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-EM-005H-1
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage or malfunction is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
21-01-023H-3
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-023H-2
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
966DBP
Service Bulletin/Repair Instructions
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-023H-1
Service Bulletin/Repair Instructions
Hyundai is conducting a campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
21-01-024H
Service Bulletin/Repair Instructions
Certain vehicles listed below may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.
21-01-025H
Service Bulletin/Repair Instructions
Consult the Hyundai Warranty Policy & Procedures and the below tables to determine New or Reman engine usage. Please note that a Reman engine may not be available for certain vehicle models/model years listed in this TSB.
21-EM-004H
Service Bulletin/Repair Instructions
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.
21-EM-005H
Service Bulletin/Repair Instructions
The Powertrain warranty coverage for certain engine repairs and/or replacement where the engine damage, defect, or failure is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
21-BR-002H
Service Bulletin/Repair Instructions
This bulletin provides best practice recommendations when performing brake service procedures.
21-EM-003H
Service Bulletin/Repair Instructions
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below.
20-BR-002H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area.
20-SS-004H
Service Bulletin/Repair Instructions
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. For all wheel/tire balance claims, the âTire Balance Data Sheetâ must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.
20-ST-001H-2
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-ST-001H-1
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-BD-014H
Service Bulletin/Repair Instructions
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.
20-AT-017H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with the following symptoms and DTC, follow the Service Procedure on Page 4. ï· Check Engine light on ï· DTC P0880/P088000 - TCM Power signal error open/short ï· Transmission stuck in 4th gear fail-safe ï· Harsh shift into Reverse and Drive
20-SS-002H(1)
Service Bulletin/Repair Instructions
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance.
20-BD-007H-1
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products.
20-EE-003H
Service Bulletin/Repair Instructions
This bulletin provides information on identifying dealer stock vehicles with either: ⢠A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. ⢠A 30 Day alert - vehicle has not started and reported an SOC in 30 days.
20-AT-016H
Service Bulletin/Repair Instructions
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions:
20-AT-014H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-AT-011H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-BD-007H
Service Bulletin/Repair Instructions
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products.
20-BD-006H
Service Bulletin/Repair Instructions
This bulletin describes the procedure to apply grease to the coupling lever of a door latch that has difficulty opening.
20-AT-008H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a âCheck Engineâ light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
20-SS-001H
Service Bulletin/Repair Instructions
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years.
20-BE-001H
Service Bulletin/Repair Instructions
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.
20-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
20-AT-001H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-AT-021H-1
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-024H
Service Bulletin/Repair Instructions
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-BE-011H-1
Service Bulletin/Repair Instructions
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.
19-GI-006H
Service Bulletin/Repair Instructions
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
19-BD-007H
Service Bulletin/Repair Instructions
The warranty coverage for the panoramic sunroof moving glass has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
19-AT-015H
Service Bulletin/Repair Instructions
If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness
19-AT-012H
Service Bulletin/Repair Instructions
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
19-BE-010H
Service Bulletin/Repair Instructions
This bulletin provides information related to clearing all Diagnostic codes for vehicles equipped with the Blue Link system (Gen 1).
19-01-009H
Service Bulletin/Repair Instructions
Some subject vehicles may experience the illumination of various warning lamps including the brake warning lamp and other lamps. This bulletin describes the procedure to apply sealant to the vacuum pump or replace the vacuum pump cap based on vehicle inspection.
Campaign T3F FS
Service Bulletin/Repair Instructions
Hyundai has launched a Service Campaign to inspect and repair or replace the vacuum pump cap on certain Veloster (FS) vehicles.
19-ST-001H
Service Bulletin/Repair Instructions
This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
19-FL-003H
Service Bulletin/Repair Instructions
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-BE-004H
Service Bulletin/Repair Instructions
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
5NP-P9V7R-11
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to inspect and (if necessary) replace the vacuum pump cap on certain 2015-17 Veloster vehicles. Service Campaign T3F provides a service procedure to inspect and apply sealant or replace the vacuum pump cap.
5NP-Y3H4E-11
Service Bulletin/Repair Instructions
On certain 2015-2017MY Veloster (FS) vehicles with 1.6L Turbo engines may experience the illumination of various warning lamps including the brake warning lamp and other lamps. This bulletin describes the procedure to apply sealant to the vacuum pump or replace the vacuum pump cap based on vehicle inspection.
5NP-Q7J2C-07
Service Bulletin/Repair Instructions
Certain 2012-2016 1.6L VELOSTER (FS) vehicles may experience a check engine warning light with the following DTC(s) found stored in the Engine Control Module (ECM): ? DTC P0455 - Evaporative emission system-Leak detected (Large leak) ? DTC P0456 - Evaporative System (EVAP) - Very Small Leak ? DTC P0449 - Canister Closed Valve (CCV) - Restricted Vent Circuit ? DTC P0451 - Fuel Tank PSI Sensor (FTPS / DPS) - Range Performance (No FTPS Change) There are no drivability symptoms associated with these DTC(s).
5NP-H6P9S-06
Service Bulletin/Repair Instructions
On some Elantra (MD/UD), Elantra GT (GD) and Veloster (FS) vehicles, a noise may develop in the steering rack. This bulletin does not address any steering function related concerns. This bulletin provides information on replacement of the steering rack support yoke assembly.
5NP-F6W6P-05
Service Bulletin/Repair Instructions
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition.
5NP-P5L7D-05
Service Bulletin/Repair Instructions
If you are servicing a vehicle with a harsh and/or delayed shift, use the GDS as shown in the Service Procedure to measure shift engagement time.
5NP-Z2J3V-04
Service Bulletin/Repair Instructions
Some Veloster (FS) and Sonata Hybrid (YF HEV) vehicles may experience a check engine warning light ON with any of the following DTCs found stored: ? P0442 - Evaporative System (EVAP) - Small Leak ? P0455 - Evaporative System (EVAP) - Large Leak ? P0456 - Evaporative System (EVAP) - Very Small Leak
5NP-S5Y6V-04
Service Bulletin/Repair Instructions
This bulletin provides information related to ECM (Engine Control Module) software update for diagnostic trouble code (DTC) P0441 - Canister Purge Valve (CPV) - Incorrect CPV Flow. There is no vehicle performance concern associated with this condition.
5NP-P5G8M-03
Service Bulletin/Repair Instructions
The MDPS (motor driven power steering) assembly contains a flexible rubber coupling which may wear over time resulting in a slight "clicking" or "thud" type noise when turning the steering wheel. This bulletin describes the service procedure to replace the coupling. Refer to the warranty and service parts information outlined in this bulletin whenever MDPS coupling replacement is required.
5NP-L6Q7E-03
Service Bulletin/Repair Instructions
This bulletin provides information related to ECM (Engine Control Module) software update for diagnostic trouble code (DTC) P0441 - Canister Purge Valve (CPV) - Incorrect CPV Flow. There is no vehicle performance concern associated with this condition.
5NPU7G9E02
Service Bulletin/Repair Instructions
Some Veloster (FS) and Sonata Hybrid (YF HEV) vehicles may experience a check engine warning light ON with any of the following DTCs found stored: ? P0442 - Evaporative System (EVAP) - Small Leak ? P0455 - Evaporative System (EVAP) - Large Leak ? P0456 - Evaporative System (EVAP) - Very Small Leak This bulletin provides the service procedure to inspect vehicles for a potential crack found at the evaporative canister insert nuts: ? If crack is not found at canister insert nut: Bracket Kit (includes bracket bolts & rubber washers) and Bolts (and a nut for FS) as listed in the Part Information table (page 2) are to be installed. ? If crack is confirmed at the canister insert nut: Replacement Canister Kit, Bolts (and a Nut for FS) as listed in the Parts Information table (pages 2-3) are to be installed.
5NPH9L4R02
Service Bulletin/Repair Instructions
Hyundai has launched a service campaign to inspect and if needed, repair the evaporative emissions canister and bracket on certain model year 2011? 2015 Hyundai Sonata Hybrid and 2012 ? 2016 Veloster vehicles. This campaign affects such vehicles registered in and operated in Alaska, Connecticut, Delaware, Illinois, Indiana, Iowa, Kansas, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Hampshire, New Jersey, New York, North Dakota, Ohio, Pennsylvania, Rhode Island, South Dakota, Utah, Vermont, West Virginia, and Wisconsin, and the District of Columbia. Reason for this Service Campaign During winter months, large quantities of salt are used to de-ice roads in the states noted above. Road salt and water can corrode the bracket holding the canister in place; as well as the seal within the canister. This can result in the need to replace these components and if necessary, the canister itself.
5NP-D7T2K-01
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE TAILGATE SWITCH ON CERTAIN 2015-16 MODEL YEAR VELOSTER VEHICLES. SERVICE CAMPAIGN T1O PROVIDES A PROCEDURE TO REPLACE THE TAILGATE SWITCH.
5NP-N3T9R-01
Service Bulletin/Repair Instructions
ON CERTAIN 2015-16MY VELOSTER (FS) THE TAILGATE HANDLE MAY NOT FUNCTION PROPERLY DUE TO AN INTERNAL ISSUE WITH THE TAILGATE SWITCH. THIS CONDITION MAY AFFECT THE TAILGATE OPEN AND CLOSING FUNCTIONALITY.
5NP-F2Q9S-01
Service Bulletin/Repair Instructions
HYUNDAI MOTOR AMERICA HAS ADDED 2015MY VELOSTER VEHICLES TO SERVICE CAMPAIGN TY6. SERVICE CAMPAIGN TY6 PROVIDES A SERVICE PROCEDURE TO REPLACE THE MANUAL HEATER CONTROL UNIT ON CERTAIN 2014-15 MODEL YEAR VELOSTER VEHICLES.
5NP-A4B3R-01
Service Bulletin/Repair Instructions
ON SOME VELOSTER (FS) VEHICLES EQUIPPED WITH THE MANUAL HEATER CONTROL UNIT, THE INTERNAL SWITCH FOR THE BLOWER (FAN) SPEED CONTROL MAY BECOME INOPERATIVE.
5NP-M6C8D-10
Service Bulletin/Repair Instructions
THIS BULLETIN DESCRIBES THE PROCEDURE TO VERIFY THAT THE FUSE AND JUMPER SETTINGS FOR THE REMOTE ENGINE START CONTROL MODULE ARE SET FOR THE APPLICABLE VEHICLE, AND IF NECESSARY, HOW TO MAKE ADJUSTMENTS TO THESE SETTINGS.
5NP-S9D9P-10
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES INFORMATION ON COMPONENTS, ATTRIBUTES, AND PRECAUTIONS OF THE 7-SPEED DRY-TYPE DUAL CLUTCH TRANSMISSION (DCT).
5NP-B3N9F-09
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES INFORMATION FOR NEW SOFTWARE TO UPDATE THE NAVIGATION AND DISPLAY AUDIO SYSTEM TO INCLUDE THE APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.
5NP-B6E2P-10
Service Bulletin/Repair Instructions
THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE
5NP-Q7S7E-09
Service Bulletin/Repair Instructions
THE SHIFT LEVER ON SOME 6-SPEED VEHICLES MAY INTERMITTENTLY NOT SHIFT OUT OF PARK. THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.
5NP-F9E3D-09
Service Bulletin/Repair Instructions
THIS BULLETIN DESCRIBES STEPS TO ACTIVATE APPLICABLE VEHICLES WITH NAVIGATION OR DISPLAY AUDIO RADIOS THAT HAVE BEEN DE-ACTIVATED FOR THE FOLLOWING REASONS: H A CUSTOMER WHO INITIALLY WAIVES BLUE LINK ENROLLMENT, AND THEN DECIDES TO ENROLL AFTER PURCHASE OF VEHICLE. H A CUSTOMER WHO ALLOWS ALL PACKAGES OF THEIR BLUE LINK SUBSCRIPTION TO EXPIRE AND THEN WISHES TO RE-SUBSCRIBE TO BLUE LINK. H A CUSTOMER WHO DID NOT ENROLL IN BLUE LINK WITHIN THE FIRST 30 DAYS OF OWNERSHIP (AT WHICH TIME THE DEVICE BECOMES INACTIVE), BUT THEN DECIDES TO ENROLL. H A SUBSEQUENT OWNER WHO WISHES TO ENROLL IN BLUE LINK.
5NP-E2D7G-09
Service Bulletin/Repair Instructions
THE FOLLOWING VEHICLES ARE EQUIPPED WITH A 6-SPEED AUTOMATIC TRANSMISSION. THE ATF LEVEL MUST BE CHECKED BY THE FOLLOWING PROCEDURE.
16-FL-002
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
5NP-J5E3D-03
Service Bulletin/Repair Instructions
Hyundai Motor America is conducting a Service Campaign to update the ECM software on certain 2016 Model Year Accent and Veloster vehicles. Service Campaign T1S provides a procedure to update the ECM software.
15-01-001
Service Bulletin/Repair Instructions
HYUNDAI 15 MY VELOSTER: THIS BULLETIN INFORMATION SUPERSEDES TSB 14-01-059. INFORMATION IS PROVIDED ON ENGINE CONTROL MODULE (ECM) SOFTWARE UPDATE WHERE NO DRIVABILITY SYMPTOMS INVOLVED BUT EXPERIENCE CHECK ENGINE LIGHT ON. *LJ UPDATED 9/15/15. *PE
15-01-006
Service Bulletin/Repair Instructions
HYUNDAI VELOSTER TURBO: SOME 15 MY VELOSTER TURBO VEHICLES, THE INTERCOOLER MAY REQUIRE REPLACEMENT DUE TO A RESTRICTION IN THE PRESSURE PORT WHICH COULD REDUCE ENGINE POWER & CHECK ENGINE LIGHT COULD ILLUMINATE WITH DTC P0299. *LJ
15-AT-001
Service Bulletin/Repair Instructions
HYUNDAI ACCENT, ELANTRA, SANTA FE, SONATA, TUCSON, VELOSTER , AZERA: IMPROPERLY OPERATING THE RANGE SWITCH MAY RESULT IN SOME TROUBLE CODES RELATING TO THE RANGE SWITCH. *LJ
14-01-059
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
14-01-047
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.