Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1201493
The purpose of this article is to provide updated repair guidelines for the engine oil pan leak on all 8.8L gasoline and LPG engines. Engine oil can leak from the rear of the engine oil pan due to an excessive gap in the sealing area between the engine oil pan and the engine block.
IK1900198
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK2600090
New CARB Idle Reduction Change Request
IK4300035
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600255
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2600047
Engine replacements for all International engines will need to follow this procedure.
IK1600272
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK1500112
This article will guide the reader through steps to help gain a general understanding of the LPG Gen 1 and Gen 2 fuel supply systems, as well as proper fuel system checks to obtain boost pressure.
IK0600030
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK2200169
This document will guide the user through repairing a Next Gen CE Bus Driver's Window with loose, displaced, or falling-out upper or lower seals. See symptoms below for an example of the issue.
IK2200119
IC Bus Operator's Manuals
IK1201009
In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of humidity, an operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK1201521
This document will guide users through supplemental oil consumption diagnostics for 8.8L PSI gas and propane engines.
IK1201490
The purpose of this article is to provide updated guidance regarding PSI 8.8L repair versus engine replacement.
IK3400001
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK2300017
Title: Electric Vehicle Air Dryer Operation
IK1400005
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK0800686
Title: Radio Clock is Freezing Applies To: Next Gen CE Bus
IK1900022
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK2200170
Title: Next Gen CE Bus Starter Interlock Dash Chime Applies To: Next Gen CE Bus with starter interlock feature built prior to 2/19/25
IK2300021
Title: Servicing Air Conditioning Systems on Electric Vehicles
IK0500054
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK2200088
Title: Factory Installed Air Conditioning, EC4.0 System BE, CE, FE, RE Bus Models
IK2300041
Title: 6090/6091 Connector Damage Applies To: IC Bus® Electric CE Series, International® eMV™ Series
IK1400023
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0900141
This document will guide a user to replace and reroute Charge Air Cooler (CAC) for vehicles built with the Cummins ISB and B6.7 engines.
iK1201485
This document will guide the user through the exhaust manifold inspection process and cover the change in the exhaust manifold installation procedure to prevent damage due to thermal expansion.
IK0400037
This document is to guide users to eliminate brake pedal rattle noise.
IK08000403
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
IK0800482
This document covers battery diagnostics, maintenance and storage requirement.
IK0800351
J1939 Data Link Source Address Information
IK0300010
Diagnosis of chassis wander complaints.
IK0400040
General Wheel Speed Sensor Troubleshooting
IK2200109
Bus seat back foam inspection guidelines
IK1201457
Cummins B6.7 Grid Heater Relay
IK2200154
Luggage rack upholstery repair; only busses equipped with luggage rack.
IKo800080
J1939 Data Link Troubleshooting
IK0700120
QLS Emergency Calibration Revert Process
22502
Per agreement with EPA and CARB, Cummins, Inc. provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
IK1200101
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK0800554
Telematics installation guidelines - Only units with 500K data link
IK0800407
Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
IK0700115
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
IK1201472
Pico Scope CCOS (Crankcase Separator Test)
IK0800607
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
PicoScope Test Resistance and Ohmmeter
IK1201469
PicoScope Test One Channel RCT
IK0800080
J1939 Data Link Troubleshooting
IK1000003
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK2600251
How to obtain As built parameter list
IK2600254
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
IK1201299
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
21506
Certain school buses may not conform to Federal Motor Vehicle Safety Standard (FMVSS) 217 â the exit opening configuration may not meet the minimum exit opening criteria.
IK0700112
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK1201459
Cummins engine vibration with aftermarket air conditioning installed
IK1900263
Bus with Cummins B6.7 engine and Dual A/C - Cylinder Head Failures
IK1500103
Acceptable Propane Fill Adapter for Refueling
IK1201452
CPA RCT (relative compression test) for PSI propane or gasoline V8 8.8L engines; School bus models
IK1500074
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
IK0800504
Repair Procedures for Vehicles Struck by Lightning
IK0800591
CE Bus Cowl Panel Relay Kit
IK2200150
This document will guide the user through determining if there is a sealing issue with the rear emergency door on a CE Bus.
IK2200149
This article is for adding additional protection to the driver's area of the bus to help mitigate the transmission of germs.
IK0800475
Radio Diagnostics and Information
IK2200147
CE Bus fuel sending access hole in wrong location; only models with feature 47AEU built between 5/7/19 and 2/19/20
IK2200001
Bus Air Conditioning Service Contacts for HVAC Information
IK1600258
Cleaning and Disinfecting Trucks and Buses
IK1300185
Reduced ISB Engine Exhaust Brake Efficiency; Only vehicles with Allison 1000/2000 series transmissions
IK1201398
ISB 6.7 Frequent Regeneration
IK0700097
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK2200145
Bus Strobe Light Replacements
IK2200073
Bus Body Entry Door Switch, LH Panel Mounted
IK1201389
Cummins ISB Fan Drive Belt Chirp; Cummins ISB and Cummins B6.7
K0500061
CE Bus Steering Returnability Diagnostics. Only CE buses built during 1/29/2018 thru 6/11/2019 with Tilt Columns, ESP, and Steering Switch Controls. 2019 and 2020 Model year only
19506
The ADB22X caliper on the left (driver side) rear corner on school bus applications may experience an unintended reduction in running clearance during operation, which can lead to a dragging brake. The problem occurs intermittently.
19101
The required Evaporative Emission label may have been printed with an incorrect engine family and/or model year for the engine installed at time of manufacture. Only models with PSI gasoline or propane engines.
IK0700079
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
IK0500061
This document will guide the user through diagnosing steering wheels not returning to center on IC CE Buses. Only models with feature code 0005708 (tilt column P/N 4095815C91 or 4110141C91), with 0004AZS (air brake ABS with ESP) or 0004JNX (hydraulic brakes), with 0047DNK or 0047DNU or 0047DWC (steering wheel switch).
IK0200013
Suggested alignment target values when performing a vehicle axle alignment
IK0800484
Voltage gauge drops on cold engine start-up; Only models built with Cummins ISB, B6.7, ISL, or L9 engines
K1200716
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
IK2200116
Bus Door Adjustment procedure for Electric and Air; only models built 09/15/11 or later
18117
Certain buses may have been built without a CH545 Key (matched key) Vandal Lock as ordered by the customer.
18520
The brake pressure switch on these buses may become stuck which results in a false fault code and brake warning light.
IK1500097
Gasoline Engine Bus Fuel System Issues; only models built with PSI 8.8 Gasoline Engine
IK0900077
Fuel Fired Engine Coolant Heaters
IK0800503
ISB Starting System Diagnostics; Only models built with cummins ISB engines
REC18517
The brake air line tube from the relay valve port to the left brake modulator valve may be improperly routed resulting in a kinked air line.
IK0900132
Bus coolant hose kink; only models with propane or gasoline engines
IK1300169
Bus Lacking Power Climbing a Hill; only models with PSI 8.8L gasoline engine
IK0400016
Aggressive Brakes with Air Brake Foot Valve Leak on Bus; only models with feature code 04WEA - Parking Brake Interlock - With Air Brakes Only
IK0800522
Repair Information for Damaged Headlight Connector
IK2600007
How to Get from History and Program a BCM or ESC; only models equipped with a BCM or ESC
IK2600215
Applying Advanced Logic Templates; only models equipped with a BCM or ESC
REC18512
The spring actuated parking brake chamber may have been improperly crimped to the service brake chamber section of the brake chamber assembly resulting in an air leak in the service brake and possible separation of the spring brake chamber.
REC18513
The spring actuated parking brake chamber may have been improperly crimped to the service brake chamber section of the brake chamber assembly resulting in an air leak in the service brake and possible separation of the spring brake chamber.
IK0800445
Body Controller Updates for 500k Baud Data link
REC18V-563-18E-0
The wheelchair lift positioning input cam may fail while the lift is in use resulting in a disabled cutoff switch.
FSC18110
The Cummins ISB engine may have been assembled with a modified fuel filter mounting bracket resulting in possible improperly routed engine grid heater harness.
IK2200143
Diagnosis and repair of intermittent operation of the Child Checkmate reset button.
IK1201360
Cylinder Performance Analyzer (CPA) Resource Center
IK1600246
Hood Cable replacement; only models with Gas or Propane engines
FSC18105
Certain CE Series school bus models may have been built with an incorrect slot location and size for the vandal lock door header.
IK1500096
Gasoline Bus - 60gal Fuel Tank Baffles in Incorrect Locations; only models with gasoline engine
IK1900220
Geotab with WYE Cable Installation; only models equipped with OnCommand Connection
REC18508
Certain school buses may not conform to Federal Motor Vehicle Safety Standard (FMVSS) 217 The force necessary to operate the emergency window release latch may exceed the maximum allowable force of 20 lbs.
REC18506
The roll stability valve air supply line may be incorrectly routed. This condition does not affect normal brake operation. However, during a stability control oversteer event and with slippery road conditions, the parking brakes may be modulated unintentionally.
REC18501
A fuel system relay for the propane booster pump and scavenge pump may experience intermittent continuity causing the fuel pump to stop running resulting in unintended stalling condition, no start, or hard start condition.
IK2200070
Bus Body Tie Down, Floor Sill Repair
IK4300001
Updating OnCommand Link with Accelerator
IK2200137
Bus Passenger Window Troubleshooting; only buses built after 4/17/17
IK2700100
OnCommand EZ-Tech
IK2200139
Driver?s seat belt tongue button; Only with Seat Belt Part numbers 4091405c1 thru 4091408c1
IK2500511
Using Supplier Software to Check DTCs
IK2200087
Bus Entrance Door Adjustment Procedures; only models built prior to 9/15/2011
IK2700065
EZ-Tech Download Center
IK0800374
How To Get A Helios Capture
IK2500127
Using Vehicle Health Report Faults
IK2700090
OnCommand EZ-Tech Download Center
IK1900203
Troubleshooting & Resetting HVAC Doors; only vehicles with Feature Codes 0016WCT and 0016WCS
IK2900029
Diagnostic Interface Cable Reference Guide
IK0400155
IC Bus Service Brake Switch Inspection; only models with Hydraulic Brakes
IK0400154
Hydraulic Brake System Park Brake Inspection and Adjustment Procedures; only models with Hydraulic Brake system equipped with 04GBJ Park Brake
REC17505
The hydraulic brake drop hose to the brake calipers on the steer axle wheel ends may be improperly routed resulting in possible contact with the tire.
IK0700096
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
IK0800546
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
IK2600008
How to Diagnose Electrical Problems with Diamond Logic Builder; only models equipped with a BCM or ESC
IK0500058
Steering Fluids
IK1201248
Cooling System Flush Procedure
IK2200016
Post Trip Inspection System Will Not Disarm or Does Not Operate Correctly; excludes Child Reminder System or Child Check Mate.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.