Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
I-22-03-02
Indian Motorcycle identified that on Indian Scout Models there is a potential for damage to occur to electrical hardware or the vehicle harness if the battery ground cable and ground joint is not connected properly. Damage can occur during procedures that require the battery cable to be disconnected or during battery removal and installation.
IND-02-14-2022
Best practices for gauges, speedometers, and tachometers providing information regarding how to clean and maintain. The version has been translated into French.
I-20-06 R02
Indian Motorcycle has determined that some 2014-2020 FullâSize (111 c.i. / 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.
IDH-HOLD
EFFECTIVE IMMEDIATELY: STOP SALE on affected motorcycle(s) identified in your inventory until further notice.
I-20-06 R01
Indian Motorcycle has determined that some 2014-2020 FullâSize (111 c.i. / 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.
I-20-12-01
This Team Tip has been released by Indian Motorcycle to provide information regarding odometer maintenance and address concerns about correct odometer value.
ISA-20-03
Indian Motorcycle has identified a potential calibration issue affecting some 111/116 c.i. motorcycles. When active, the P1530 fault causes the motorcycle to operate in a reduced power (limp) mode.
I-19-09-01
This Team Tip identifies differences between crankcases used throughout Indian Motorcycle 111 C.I. engine production, and introduces a new service crankcase for 2014-2020 models.
I-19-09-02
Updated information has been added to all Indian Motorcycle Service Manuals to provide dealers with clear directions when servicing the fuel system. Be sure to reference the applicable Service Manual for the most accurate information.
I-19-03-01
This Team Tip has been released to assist dealers when servicing vehicles that have, or are suspected to have, aftermarket (non-OEM) modifications. It is critical for expedient and accurate diagnosis of a motorcycle, to identify and disclose all existing modifications to Indian Technical Service. Use of aftermarket components can create operating characteristics and sensor feedback that do not align with factory parameters. These cases can send our technicians down the wrong path and result in longer diagnostic time and a poor customer experience.
ISA-19-01
Indian Motorcycle has identified a quality concern affecting some 2017â2019 full size motorcycles with chrome trim built from 7/18/2016 through 11/27/2018. The chrome trim strips applied to the front and rear fenders may exhibit a wrinkling finish shortly after installation.
I-18-11-01 R03
Indian Motorcycle has introduced new software and map updates for the Ride Command display. Dealers should encourage Indian Motorcycle riders using Ride Command to bring their bikes in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map files may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of, and has practiced both update processes so they can provide a positive customer experience.
I-18-11-01 R02
Indian Motorcycle has introduced new software and map updates for the Ride Command display. Dealers should encourage Indian Motorcycle riders using Ride Command to bring their bikes in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map files may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of, and has practiced both update processes so they can provide a positive customer experience.
I-18-11-03
This Team Tip is designed to inform dealers about updated information regarding gear position switches for all 2014- 2019 Indian Motorcycle (111 c. i.) models. Updated information has been added to the Service Manual to provide dealers with clear direction on how to properly maintain and service gear position switches. We have also updated the maintenance interval chart to include the inspection and cleaning of the gear position switch at 10,000 mile intervals.
I-18-11-01 R01
Indian Motorcycle has introduced new software and map updates for the Ride Command display. Dealers should encourage Indian Motorcycle riders using Ride Command to bring their bikes in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map files may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of, and has practiced both update processes so they can provide a positive customer experience.
I-18-03
Indian Motorcycle has identified three separate calibration concerns currently affecting 2017 and 2018 full-size Indian Motorcycles. The Indian Motorcycle engineering team has released updated ECM and cluster calibrations to correct these concerns. Gear Position Fault, Coil Driver Fault, and Battery Drain issues will all be resolved with this reflash. Refer to Team Tip I-17-11-01 for more details.
I-18-05-01
2014-2018 Indian Motorcycles utilize Absorbent Glass Mat (AGM) batteries which are selected for their superior vibration resistance, weight savings, and high output. This Team Tip is being released to provide the Indian dealer network with specific recommendations to help maintain and restore the AGM type batteries used in Indian Motorcycles.
I-18-06 R01
Indian Motorcycle is actively investigating a potential concern affecting 111 ci engines that have been equipped with the Thunder Stroke 116 ci Stage 3 Big Bore accessory kit. Investigation is currently planned to conclude by 5/7/18, and at that time this communication will be re-issued with additional information. In the interim, Big Bore Kits and vehicles equipped with kits should not be sold.
I-18-02
Indian Motorcycle has identified three separate calibration concerns currently affecting 2017 and 2018 full-size Indian Motorcycles. The Indian Motorcycle engineering team has released updated ECM and cluster calibrations to correct these concerns. Gear Position Fault, Coil Driver Fault, and Battery Drain issues will all be resolved with this reflash. Refer to Team Tip I-17-11-01 for more details.
I-17-11-01
Indian Motorcycle has identified three separate calibration concerns currently affecting 2017 and 2018 full-size Indian Motorcycles. The Indian Motorcycle engineering team is working quickly to develop and release updated ECM and cluster calibrations to correct these concerns, but during the interim, the strategies outlined below can reduce customer frustration and unnecessary diagnostic time.
G-17-10-02
At Polaris, we are committed to the safety of our customers and riders. Through product design, dedicated safety engineering, and increased consumer awareness, Polaris continues to work toward a safe riding experience and proper operation of our products. The following information can be used to help identify and report Product Safety Concerns.
I-17-02
Indian Motorcycle has determined that some Chieftain and Roadmaster models, produced between 6/21/2017 and 7/27/2017, may experience functional issues with the Ride Command navigation system and compass feature. When using navigation on affected bikes, the heading will always show the vehicle traveling North, causing turn-by-turn to continuously reroute. Additionally, the compass image on the Ride Data screen will not be shown.
ISA-17-02
Indian Motorcycle has determined that some 2014-2017 111ci motorcycles equipped with Stage 2 Performance Cams, Part Number 2881676, may experience intermittent drivability issues.
G-16-11-01
Polaris has released Team Tip G-16-10-01 to inform dealers that Polaris Mobile Digital Wrench (PMDW) version 3.28 or later requires dealers to enter a valid 10-digit Digital Wrench serial number to operate the app. The serial number requirement has been added to improve visibility to app downloads and usage.
I-16-10-01
The Purpose of this Team Tip is to call attention to the importance of proper Ride Command set-up prior to retail, and to answer a few questions about basic troubleshooting and system operation. It is important to understand how Ride Command operates and what to expect during normal operation. When delivering an Indian Motorcycle equipped with Ride Command, make sure the customer understands each of the points outlined in this communication. Additional Ride Command information can be found under âTraining and Resourcesâ under âNews, Forms & Linksâ on your dealer homepage and also at https://my.indianmotorcycle.com/ridecommand/tutorials
G-15-12-01 R03
There is no doubt that for a Polaris customer the process of picking up a brand new vehicle is one of the most exciting times in the ownership experience. To ensure that all Polaris dealers are equipped to deliver a world-class experience that matches the high quality and excitement of the products, PCDX was developed to create a mobile streamlined dealership delivery experience. PCDX combines the setup, registration, and delivery process into one easy to use application.
G-15-12-01 R02
PCDX is an online and mobile interface for providing a consistent dealer setup and customer delivery experience. The interface walks the dealer and the customer through a standardized online form that includes the PDI (pre-delivery inspection), general warnings, assembly and inspection, safety bulletins, test ride, customer information, customer walkaround and discussion, and customer acceptance. This application has been proven in dealerships to automate document retention, streamline vehicle setup, and provide a consistent, professional customer experience. Vehicles shipped after 11/1/2015 no longer include a paper PDI form with the vehicle setup material; instead dealers should complete the vehicle setup and PDI using the PCDX application, which can be located on the Dealer Website under Service and Warranty â PCDX.
G-15-12-01
This Team Tip is being released to dealers to provide information regarding the required transition to online PCDX and PCDX training.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.