Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011Q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-055D
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008D
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-040
Service Bulletin/Repair Instructions
3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. INFINITI Connection with InTouch⢠Services are no longer available on the APPLIED VEHICLES listed above.
ITB12-072I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008C
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-072H
Service Bulletin/Repair Instructions
INFINITI AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-011C
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT JUDDER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-072G
Service Bulletin/Repair Instructions
INFINITI AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-053C
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013 JX35; METER BACK LIGHT ILLUMINATION AND DISTANCE TO EMPTY INACCURACY Service Campaign ID # P2538 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # P2538. ï· Discard all previous versions of ITB12-053.
PC835 - R1606 Ca
Service Bulletin/Repair Instructions
R1606 Occupant Classification System (OCS) Campaign Quality Review ***** Retailer Announcement ***** INFINITI is committed to the safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1606). If the VIN displays QA campaign ID PC835, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIâs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC835. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. ⢠Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.
ITB13-008B
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-037E
Service Bulletin/Repair Instructions
RADIO PRESETS / CLIMATE CONTROL SETTINGS / NAVIGATION SETTINGS CHANGE WITH INTELLIGENT KEY MEMORY This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-006B
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2017 QX60; VDC WARNING LAMP ON WITH DTC C1116 STORED This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-021B
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-015B
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-059B
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK INTERMITTENTLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB13-057B
Service Bulletin/Repair Instructions
2013 JX35, 2014-2015 Q50 & QX60; ONE OR BOTH INTELLIGENT KEYS LOST PRIOR TO CUSTOMER DELIVERY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB17-005A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
ITB12-041D
Service Bulletin/Repair Instructions
SIRIUSXM SATELLITE RADIO / WEATHER / TRAFFIC / TRAVEL LINK ACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB17-041A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB10-017E
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT REQUIRES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-003F
Service Bulletin/Repair Instructions
NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011P
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-014A
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 QX60 AWD ERROR DISPLAYED AND DTC C1204 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-034B
Service Bulletin/Repair Instructions
CVT OIL LEAK DIAGNOSIS USING FLUORESCENT DYE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-012i
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 â 2018 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
EXPIRATION NOTIF
Service Bulletin/Repair Instructions
Expiration Notification - 2G Telematics Hardware Replacement Campaign Summary In 2016, INFINITI launched a Client Satisfaction Initiative (CSI) that provided clients with an opportunity to update the Telematics Control Unit (TCU) in vehicles equipped with a TCU designed to connect to the 2G cellular network. AT&T stopped accepting enrollments on the 2G cellular network, and discontinued its 2G cellular network coverage on December 31, 2016. Once the 2G cellular network was discontinued, there was no access to the INFINITI Connection features without a TCU hardware upgrade. Because AT&T will shut down its 3G network on December 31, 2021, INFINITI is discontinuing this Client Satisfaction Initiative to upgrade from 2G to 3G compatible hardware effective immediately. 3G services will continue to be provided until December 31, 2021. Vehicles equipped with a TCU that connects to the 3G cellular network will have no access to the INFINITI Connection features, including Emergency Calling and Automatic Collision Notification after that time. What Retailers Should Do Service Comm will deactivate PC451, PC452 and PC454 on any VINs on December 22, 2020. No further retailer action is required.
ITB17-007a
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT Customer Satisfaction Initiative ID # PC451, PC452 and PC454 are no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC451, PC452 or PC454. ï· Please discard all previous versions of ITB17-007.
ITB15-024a
Service Bulletin/Repair Instructions
2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB12-072f
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2019 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-066f
Service Bulletin/Repair Instructions
PREMIUM NAVI/AUDIO VISUAL CONTROL UNIT DIAGNOSIS AND ORDERING This bulletin is no longer applicable. Discard previous versions of ITB11-066.
ITB18-026c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB13-008a
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-012h
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 â 2018 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB12-011o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on the next page. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
ITB14-011d
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-014
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2020 QX60; REMOVAL OF HEADLIGHT ASSEMBLY LOCATING BRACKET SERVICE INFORMATION If replacement of a Front Combination Headlamp assembly (headlight assembly) is necessary, for the applied vehicles, the locating bracket (if present) on the new replacement headlight assembly must first be removed before installation. Inspect the new replacement headlight assembly and confirm if a locating bracket is attached, with a Torx screw, on top in the center (see Figure 1). Is a locating bracket present? - NO: This bulletin does not apply. Continue with the installation of the new replacement headlight assembly. - YES 1. Using a T10 Torx screwdriver, remove the locating bracket attached to the topcenter of the replacement headlight assembly (see Figure 1). 2. Discard the locating bracket and Torx screw. 3. Continue the installation of the replacement headlight assembly. NOTE: Refer to the Electronic Service Manual (ESM) for the procedure to remove or install a headlight assembly. CAUTION: Take care when installing the headlight assembly so that the painted surface of the fender is not damaged. - Black electrical tape can be used to protect the edge of the fender while installing the headlight assembly.
ITB14-053b
Service Bulletin/Repair Instructions
ABNORMAL NOISE FROM FRONT ENGINE MOUNT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-011
Service Bulletin/Repair Instructions
DEAD PEDAL REPLACEMENT SERVICE INFORMATION If the dead pedal needs to be replaced for anyreason, it is no longer necessary to replace the front floor trim (carpet). The dead pedal is now available as a service part. NOTE: Do not replace the carpet if only the dead pedal is needed. ACTION Follow the SERVICE PROCEDURE on the next page to replace ONLY the dead pedal. NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB13-055c
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-026b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB18-006a
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2017 QX60; VDC WARNING LAMP ON WITH DTC C1116 STORED This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB12-011m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-026b
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
Revision 1-IEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
ITB18-039
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
ITB12-072e
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2017 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies to AWD (All-Wheel Drive) vehicles only. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-026a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
REVISION 4-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative UPDATE October 12, 2018 Please discard earlier versions of this bulletin. The announcement from February 17, 2017 has been revised to include: - ~397 retailed vehicles have been added to campaign ID PC454
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
IPSB18-218 Retai
Service Bulletin/Repair Instructions
DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
ITB12-072d
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2017 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB12-011l
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
ITB17-026a
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL IF CUSTOMER REPORTS: Customer routinely experiences difficulty fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.
ITB13-035c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB13-044f
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.
ITB18-026
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each retailer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
PC501
Service Bulletin/Repair Instructions
CVT Software Update/Warranty Extension Voluntary Service Campaign UPDATE April 6, 2018 Please discard earlier versions of this bulletin The announcement from December 7, 2016 has been revised to include: - The campaign repair has been revised to be software update only - Retailers must submit any open campaign claims for diagnosis or repair for CVT concerns no later than April 20, 2018 in order to have covered by this service campaign. After this date, all claims for diagnosis or repair related to CVT concerns on vehicles affected by PC501 will be administered under the Warranty Extension if still applicable
ITB16-048c
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013 JX35 AND 2014 QX60; CVT This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB13-052b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB11-005d
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB03-051L
Service Bulletin/Repair Instructions
HEADLAMP FOGGING This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
ITB12-011k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
ITB18-003
Service Bulletin/Repair Instructions
REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
ITB12-011j
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.
ITB09-039e
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-009a
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g
Service Bulletin/Repair Instructions
BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
ITB12-011i
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with factory Navigation system. This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.
ITB12-011h
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with factory Navigation system. This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.
ITB11-005c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-016c
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2016 QX60 OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 15 and 17 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-002b
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-016b
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2016 QX60 OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB14-053a
Service Bulletin/Repair Instructions
THUNK SOUND ON FIRST FEW ACCELERATIONS OF THE DAY This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
ITB16-021a
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
P7331
Service Bulletin/Repair Instructions
Disabling the 2G TCU Voluntary Service Campaign ***** Campaign Summary ***** Infiniti is conducting a Voluntary Service Campaign to disable (turn off) the 2G Telematics Control Unit (?2G TCU?). The subject QX56/QX80, JX35/QX60, M37/M56/Q70, and 2014-15 Q50 vehicles are equipped with Continental GEN1 TCU devices transmitting at 2/2.5G (GSM/GPRS/UMTS) frequencies and are designed to work with 2G cellular service. The 2G cellular service is no longer active in the United States. The subject 2G TCUs are no longer connected to telematics services and no longer perform any function in the affected vehicles. This campaign is being performed out of an abundance of caution to help safeguard against potential cybersecurity issues. - All eligible vehicles that enter the service department for any reason should have the subject 2G TCU deactivated. This campaign will be performed at no charge to the client for parts and labor. - Vehicles that have been upgraded to 3G TCUs are not subject to this campaign. - For clients interested in the 3G TCU upgrade as opposed to deactivation, please refer to ITB17-007 (PC451, PC452, or PC454)
ITB17-041
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION INTRODUCTION Infiniti is conducting a Voluntary Service Campaign (in the U.S. ONLY) on certain specific 2013-2016 Infiniti vehicles equipped with 2G Telematics Hardware to disable the 2G Telematics Control Unit (TCU). The 2G cellular service is no longer active in the United States and the subject TCUs are no longer connected to telematics services (Infiniti ConnectTM) and no longer perform any function in the affected vehicles. This campaign is being performed out of abundance of caution to help prevent potential cybersecurity issues. - Applied vehicles equipped with the 2G Telematics Control Unit (TCU) that enter the service department for any reason should have the subject TCU deactivated. This campaign will be performed at no charge to the customer for parts or labor. - For customers interested in the TCU update as opposed to deactivation, please refer to ITB17-007. IDENTIFICATION NUMBER Infiniti has assigned identification number P7331 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer?s inventory.
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.
ITB13-055b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.
ITB15-010c
Service Bulletin/Repair Instructions
INFINITI; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard previous versions of this bulletin.
ITB17-002a
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin does not apply to hybrid vehicles. This bulletin has been amended. The Title has been changed. The PARTS INFORMATION and CLAIMS INFORMATION sections have been amended. Discard previous versions of this bulletin.
ITB17-015
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
ITB15-012g
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2017 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehciles equipped with a 6 cylinder engine. This bulletin has been amended to add model years to the Applied Vehicles and change the parts information. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-048b
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013 JX35 AND 2014 QX60; CVT This bulletin has been amended. A correction was made to the DTC number on page 16. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-026
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
PC501 - 2013 JX3
Service Bulletin/Repair Instructions
CVT Software Update/Warranty Extension Parts Update 2 ***** Parts Update ***** Campaign Bulletin ITB16-048 has been revised to address a part change (in the event that parts are needed) and is now available on NNAnet & ASIST. o Valve Body Kit (3170E29X9C) will now include the Control Valve Assembly, Automatic Transmission Oil Strainer Assembly, Bracket, Band, Oil Pan Gasket, and Lip Seal. o The control valve assembly is only available in kit form, but the oil strainer assembly, bracket, band, oil pan gasket and lip seal will remain available for purchase separately The previously announced restriction on remanufactured CVT assemblies will be lifted on March 24, 2017. Parts will be available for order via normal process after that date. Orders placed via DCS prior to that date will be filled.
ITB16-048a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013 JX35 AND 2014 QX60; CVT The Parts Information in this bulletin has been amended. No other changes have been made. Please discard previous versions of this bulletin.
REVISION 3-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from January 3, 2017 has been revised to include: - Campaign repair bulletin, ITB17-007 has been developed and is now available on NNAnet, and ASIST. Please discard earlier versions of this bulletin.
ITB17-007
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT This bulletin applies to vehcile equipped with navigation systems only. SERVICE INFORMATION On February 26, 2016 Infiniti announced that it was sending a reminder notification to clients affected by AT&T?s planned discontinuation of the 2G cellular network. In June 2016, Infiniti communicated instructions to retailers to update new vehicles in their inventory with 3G compatible telematics control units. At this time, Infiniti is beginning the process of making 3G compatible hardware available to owners of affected vehicles as identified above. This upgrade may require an owner to make a co-payment in order to receive the 3G hardware update. Please refer to the Claims Information below to determine if an owner co-pay is required. This client satisfaction initiative includes both the hardware upgrade and a complimentary one-year subscription to Infiniti Connection Plus telematics service; this does not apply to PC454 (see page 2 for details). You MUST use Service Comm to confirm bulletin Applicability. NOTE: - Vehicle eligibility will be viewed on the second page of Service Comm. This activity is not displayed on the main page of Service Comm because it is optional for customers to participate. - Vehicles without Navigation are ineligible as they are not equipped with TCUs. Retailer?s Responsibility It is the retailer?s responsibility to check SERVICE COMM using the appropriate Service Comm I.D. for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB17-005
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL SERVICE INFORMATION The Enhanced Multi-Media Interface Tester (EMMIT) J-51922 is a new special tool that tests the functionality of the following features: Bluetooth o Pairing/Connecting o Phonebook Access Profile o Hands Free Profile (for calls) o Bluetooth Audio test o Message Access Profile (for text messages, if so equipped) USB o Tests USB music playback o Tests USB music browsing capability AUX o Tests AUX Jack playback Use EMMIT to diagnose symptoms related to Bluetooth, USB, and AUX. If EMMIT passes diagnostic tests, the symptom is caused by the customer?s phone and not caused by the AV control unit. DO NOT replace the AV control unit. NOTE: If an AV control unit is replaced for multi-media issues that can be tested with EMMIT, a printed copy of the EMMIT diagnostic results must be included with the returned unit. See page 2 for more information about the EMMIT tool.
ITB17-002
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND TIMING CONTROL SOLENOID VALVE This bulletin does not apply to hybrid vehicles. IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve. And The valve timing control solenoid valve operates correctly and is not externally damaged, ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.
ITB12-076c
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. Step 15 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
REVISION 2-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from November 3, 2016 has been revised to include: - 283B0-3JA6A is the part number being used for all vehicles, except Q50 o This part supersedes the previous part (283B0-3JA5A). Retailers may continue to use the previous part until existing stock is exhausted. - 283B0-3JA7A is used for Q50 - These parts are not restricted and can be ordered through normal process Please discard previous versions of this announcement.
ITB12-076b
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION The Applied Vehicles in this bulletin have been amended. No other charges have been made. Please discard previous versions of this bulletin.
ITB16-048
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013 JX35 AND 2014 QX60; CVT INTRODUCTION Infiniti is conducting this voluntary service campaign on certain specific 2013 JX35 and 2014 QX60 vehicles to reprogram the TCM and, if needed, inspect and replace the CVT or CVT control valve. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number PC501 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
ITB13-052a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB16-047
Service Bulletin/Repair Instructions
INFINITI; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
ITB16-040a
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2015 QX60; DOOR MIRROR WILL NOT RETURN TO SET POSITION AFTER SHIFTING FROM REVERSE TO DRIVE This bulletin has been amended. The Title has been modified, and references to Automatic Drive Positioner have been changed to Seat Control Unit. No other changes have been made. Please discard all previous versions.
REVISION 1-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from September 2, 2016 has been revised to include: - The telematics upgrade for 2014-15 Q50 is now available. The procedure and part information has been added to this announcement.. - Second page of Service Comm is not VIN specific, service personnel should check vehicle repair history prior to offering clients an opportunity to upgrade - In lieu of repair history, TCU version can be checked on the information screen (see page 2) Please discard previous versions of this announcement.
ITB13-035b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB12-011g
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-040
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 ? 2015 QX60; DOOR MIRROR GLASS WILL NOT RETURN AFTER SHIFTING REVERSE TO DRIVE Applies to vehicles equipped with Automatic Drive Positioner IF YOU CONFIRM The door mirror glass (LH and RH) automatic tilt down-up feature does not return the glass to original position after shifting from reverse to drive. ACTION Replace the Automatic Drive Positioner (ADP) Control Unit. - Use the new part listed in the Parts Information. - Refer to the Electronic Service Manual (ESM), section ADP-Automatic Drive Positioner, for replacement information.
PC451_PC452 2G T
Service Bulletin/Repair Instructions
PC451_PC452 2G TCU UPDATE - MAIL NOTIFICATION THE PURPOSE OF THIS ANNOUNCEMENT IS TO LET FIELD PERSONNEL KNOW THAT THE FIRST 22K OWNER MAILINGS HAVE BEEN SENT OUT TODAY. THIS FIRST MAILING WAS DIRECTED TOWARDS CURRENT INFINITI CONNECTION SUBSCRIBERS OR TRIAL PARTICIPANTS. THE REMAINING OWNER NOTIFICATIONS WILL BE SENT OUT BETWEEN NOW AND DECEMBER 1, 2016. OWNER NOTIFICATION TIMING FOR Q50 OWNERS IS STILL TBD BASED ON PARTS AVAILABILITY TIMING.
ITB12-054B
Service Bulletin/Repair Instructions
THIS BULLETIN HAS BEEN AMENDED. THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
PC451_PC452_PC45
Service Bulletin/Repair Instructions
2G TELEMATICS HARDWARE REPLACEMENT CLIENT SATISFACTION INITIATIVE ON FEBRUARY 26TH, 2016 INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN JUNE 2016, INFINITI COMMUNICATED INSTRUCTIONS TO RETAILERS TO UPDATE NEW VEHICLES IN THEIR INVENTORY WITH 3G COMPATIBLE TELEMATICS CONTROL UNITS. AT THIS TIME, INFINITI IS BEGINNING THE PROCESS OF MAKING 3G COMPATIBLE HARDWARE AVAILABLE TO OWNERS OF AFFECTED VEHICLES AS IDENTIFIED ABOVE. THIS UPGRADE MAY REQUIRE AN OWNER MAKE A CO-PAYMENT IN ORDER TO RECEIVE THE 3G HARDWARE UPDATE. PLEASE REFER TO THE CHART PROVIDED ON PAGE 2 TO DETERMINE IF AN OWNER CO-PAY IS REQUIRED. THIS CLIENT SATISFACTION INITIATIVE INCLUDES BOTH THE HARDWARE UPGRADE AND A COMPLIMENTARY ONE-YEAR SUBSCRIPTION TO INFINITI CONNECTION PLUS TELEMATICS SERVICE; THIS DOES NOT APPLY TO PC454 (SEE PAGE 2 FOR DETAILS). NOTE: VEHICLE ELIGIBILITY WILL BE VIEWED ON THE SECOND PAGE OF SERVICE COMM (EXCEPT PC454). THIS ACTIVITY IS NOT DISPLAYED ON THE MAIN PAGE OF SERVICE COMM BECAUSE IT IS OPTIONAL FOR CLIENTS TO PARTICIPATE.
ITB12-011F
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION VEHICLES EQUIPPED WITH FACTORY NAVIGATION SYSTEM THIS BULLETIN HAS BEEN AMENDED. MODIFICATIONS HAVE BEEN MADE TO INCLUDE QX30. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
ITB14-011C
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 4 AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: "PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM.
ITB15012F
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - ITB15-010, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on the next page. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
ITB15-011B
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB15011B
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE: The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module See this bulletin for further detail.
ITB13-055A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB13055A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. Please see this bulletin for further information.
ITB15021A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
AT15-007E
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB-14-051
Service Bulletin/Repair Instructions
INFINITI: ON SOME VEHICLES, THE FORWARD COLLISION WARNING (FCW) MALFUNCTION HAS BEEN OR IS ON AND FLUID LEVEL FOR BRAKES IS NORMAL AND THE ABS CONTROL UNIT NEEDS PROGRAMMING, PER SERVICE PROCEDURE. MODEL 2013-14 JX35, QX60, 2014-15 Q50. *PE UPDATED 9/10/15. *PE
PC358
Service Bulletin/Repair Instructions
Infiniti is informing affected clients that their vehicles (non-Hybrid models) are eligible for Continually Variable Transmission (CVT) Transmission Control Module (?TCM?) software programming update to improve CVT service diagnostics
ITB13035A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual (ESM)). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.
ITB-14-036
Service Bulletin/Repair Instructions
INFINITI: WHILE DRIVING, UNEXPECTEDLY AND ABRUPTLY, OR UP AND DOWN, AND DISTANCE TO EMPTY (FUEL) FAILS TO GIVE CORRECT READING OF FUEL GAUGE. MODEL 2013-2014 JX35, QX60. *PE UPDATED 9/29/14. *PE
PC284A
Service Bulletin/Repair Instructions
As a result of delayed retail delivery reporting and some other factors, some retailers received CVTs they do not need. The attached excel file shows the CVTs that were shipped and also include the retailer inventory on 5/23/14 for reference.
PC284
Service Bulletin/Repair Instructions
Infiniti is conducting a Retailer Service Action to replace the CVT and reprogram/calibrate the TCM on a limited number of certain specific 2013-14 JX35/QX60 vehicles that are currently in retailer inventory.
ITB14024
Service Bulletin/Repair Instructions
SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
ITB12051C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The rear seat headphones have a "LEFT" channel and a "RIGHT" channel. The channel switch is on the headphone ear pad case. If a person is sitting on the left side (driver side) of the vehicle and their headphones are set to "RIGHT", the headphones may have static or intermittently operate (cut in and out). OR If a person is sitting on the right side (passenger of the vehicle and their headphones are set to "LEFT", the headphones may have static or intermittently operate (cut in and out). NOTE: If the headphones are set to the "correct channel" for the seating position, but still have static or do not operate, check the condition of the "AAA" headphone batteries located under the left side headphone cover. Do not replace the headphones for the above issues. See this bulletin for further detail.
ITB-13-050
Service Bulletin/Repair Instructions
INFINITI: ONCE BCM GOES INTO SLEEP MODE AND ALL DOORS ARE LOCKED, ALL OF APPLIED VEHICLES REMOTE FUNCTIONS FAILS WORK FOR APPROXIMATELY 15-20 MINUTES. MODEL 2013 JX35. *PE
ITB-13-044
Service Bulletin/Repair Instructions
INFINITI: THE INSTRUMENT CLUSTER HAS A WARNING INDICATOR, THAT ILLUMINATES, OF A LOOSE FUEL FILL CAP. MODEL YEARS 2012 AND UP. NO MODELS LISTED. *PE
PC251
Service Bulletin/Repair Instructions
Infiniti is conducting a Retailer service action to inspect and, if necessary, replace one or both of the front brake torque members on certain specific 2013 Infiniti JX35 or 2014 Infiniti QX60 vehicles currently in Retailer inventory
ITB-13-039
Service Bulletin/Repair Instructions
INFINITI: SERVICE BULLETIN CONCERNING LOW TIRE PRESSURE WARNING SYSTEM INFORMATION. *JS
ITB-13-020
Service Bulletin/Repair Instructions
INFINITI: MAY BE SHUDDER FROM THE TORQUE CONVERTER. *KB UPDATED 7/22/13. *PE UPDATED 09/23/2013 *JS UPDATED 10/24/13. *PE
ITB-92-069-D
Service Bulletin/Repair Instructions
INFINITI: DUE TO USE OF AFTERMARKET CHROMING OF ALLOY WHEELS, FOR SOME VEHICLES, THE STANDARDS ARE NO LONGER ARE MET AND ARE SERIOUSLY DAMAGED AND NOT GUARANTEE OR WARRANTY THE MODIFIED WHEELS OR PERFORMANCE. MODELS ALL. NO YEARS LISTED. *PE
ITB-13-13
Service Bulletin/Repair Instructions
INFINTI: CRUISE CONTROL WILL NOT SET AND DTC P0605 IS STORED. IF A MALFUNCTION IN THE ASCD SYSTEM IS DETECTED, THE CRUISE INDICATOR MAY STAY ON AND THE SET INDICATOR MAY FLASH. *JS
ITB-13-12
Service Bulletin/Repair Instructions
INFINITI: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE DOOR HANDLE OUTSIDE DOOR HANDLE DOES NOT RESPOND. LOCK/UNLOCK REQUEST BUTTON LOCATED ON OUTSIDE DOOR HANDLES OF VEHICLES CAN BE DISABLED (OR ENABLED) THROUGH EITHER THE "COMFORT & CONV" SETTINGS OF THE AUDIO/VISUAL/NAVIGATION SYSTEM OR THROUGH THE "COMBINATION METER SETTINGS" DEPENDING ON THE VEHICLE MODEL, YEAR, AND TRIM LEVEL. *JS
ITB-12-053
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON SOME VEHICLES, THE SUPPLEMENTAL, DTE, TO FUEL GAUGE, MAY BE INACCURATE AND SHOULD BE REPROGRAM; WHILE THE COMBINATION METER MAY NOT ILLUMINATE. MODEL 2013 JX35. *PE UPDATED 9/24/12. *PE UPDATED 4/1/13. *PE
PC193
Service Bulletin/Repair Instructions
Infiniti is conducting a Retailer Inventory Inspection on certain specific 2013 Infiniti JX35 vehicles to verify that the armatures behind both the front and rear bumper fascias are installed.
ITB-12-067
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO POSSIBLE DAMAGE TO AIR FUEL (A/F) SENSORS, CAUSED BY ENGINE CONTROL MODULE (ECM) IMPROPER CALIBRATION, THE A/F SENSORS WILL BE REPLACED, IF NEEDED. MODEL 2013 JX35. *PE
ITB-09-011-A
Service Bulletin/Repair Instructions
INFINITI: WHEN INSECTS, DIRT, FINGER PRINTS, OIL FILM, MOISTURE OR EXHAUST GAS IS NEAR OR AROUND RAIN SENSOR, THIS CAUSES THE RAIN SENSOR, WHEN WIPER LEVER IS PUSHED DOWN, TO EITHER MAKE A SINGLE STROKE OR OPERATE UNEXPECTEDLY. NO MODELS OR MODEL YEARS LISTED. *PE
ITB-12-044
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON CERTAIN VEHICLES, THE ADAS CONTROL UNITS AND RADAR ARE BEING REPROGRAMMED WITH NO CHARGE TO LABOR OR PARTS. *PE UPDATED 8/28/12. *PE
ITB-11-049-B
Service Bulletin/Repair Instructions
INFINITI: REPROGRAMMING ELECTRONIC CONTROL UNIT (ECU) ON ALL QUALIFYING VEHICLES. NO MODELS LISTED. MODEL YEARS 1998-2013. *PE
ITB-12-013
Service Bulletin/Repair Instructions
INFINITI: PERFORMING MILLIMETER WAVE (RADAR) SENSOR ADJUSTMENT SERVICE WILL REQUIRE A SPECIAL SERVICE TOOL KIT. *PE
ITB-12-005
Service Bulletin/Repair Instructions
INFINITI: VEHICLES USING INTELLIGENT KEY SYSTEM AND/OR DOOR REQUEST SWITCH CAN NOT LOCK OR UNLOCK VEHICLE DOORS. *PE