Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB23-023A
Service Bulletin/Repair Instructions
AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB17-060C
Service Bulletin/Repair Instructions
INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011Q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-011G
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-041
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-015
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-060B
Service Bulletin/Repair Instructions
INFINITI; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-026D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-012D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-055B
Service Bulletin/Repair Instructions
INFINITI; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-005B
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-055A
Service Bulletin/Repair Instructions
INFINITI; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB15-026C
Service Bulletin/Repair Instructions
INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-012C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB12-011P
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-023a
Service Bulletin/Repair Instructions
2018 Q50, Q50 HYBRID, AND Q60; POI DOES NOT DISPLAY AFTER VOICE MENU CALL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB18-040d
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-002c
Service Bulletin/Repair Instructions
2018-2020 INFINITI; DISPLAY CONTROL UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-005a
Service Bulletin/Repair Instructions
CLOCK, AUDIO, HVAC OR NAVIGATION SETTINGS INTERMITTENTLY CHANGE ON THEIR OWN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042c
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB19-002b
Service Bulletin/Repair Instructions
2018-2020 INFINITI; DISPLAY CONTROL UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on the next page. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
ITB18-040c
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB14-011d
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-002a
Service Bulletin/Repair Instructions
2018-2019 INFINITI; DISPLAY CONTROL UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB18-040b
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. Please see Amendment History on the last page. Please discard previous versions of this bulletin.
ITB19-006
Service Bulletin/Repair Instructions
INFINITI; MIL ON WITH DTC P219A AND/OR P219B STORED SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
ITB19-005
Service Bulletin/Repair Instructions
CLOCK, AUDIO, HVAC OR NAVIGATION SETTINGS INTERMITTENTLY CHANGE ON THEIR OWN This bulletin applies only to vehicles equipped with INFINITI InTouch (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with INFINITI InTouch?, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.
ITB16-012b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-042b
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB12-011m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-002
Service Bulletin/Repair Instructions
2018-2019 INFINITI VEHICLES; DISPLAY CONTROL UNIT SERVICE INFORMATION SERVICE INFORMATION If the Display Control Unit (DCU) needs to be replaced on an APPLIED VEHICLE for any reason, follow the steps in the Service Procedure to: - Confirm proper diagnosis and repair with TECH LINE to obtain DCU order approval, then place the order with DENSO. NOTE: The DCU order approval process does not apply to 2017 model year and earlier models. TECH LINE authorization is not needed for 2017 model year and earlier models. - Configure the Multi AV system. - 2018-2019 QX30 vehicles only: Register the replacement DCU. DCU registration is necessary whether or not the vehicle has an active Infiniti InTouch Apps subscription. NOTE: The original DCU must be installed in the vehicle while performing part of this procedure. DO NOT remove the original DCU until instructed.
ITB19-001
Service Bulletin/Repair Instructions
CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 - (CHASSIS CONTROL BRAKE SYSTEM) - C1B90-00 - (DIRECT ADAPTIVE STEERING SYSTEM) - C1B92-00 - (BRAKE CONTROL SYSTEM) - C1B93-00 - (ENGINE/HEV SYSTEM) - C1B94-00 - (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
ITB18-040a
Service Bulletin/Repair Instructions
INFINITI; SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. Please see Amendment History on the last page. Please discard previous versions of this bulletin.
ITB18-040
Service Bulletin/Repair Instructions
INFINITI; SOFTWARE UPDATES FOR INFOTAINMENT ISSUES IF YOU CONFIRM Any one or a combination of the following on an applied vehicle: - Reverse camera is blank (vehicles manufactured before May 1, 2018) - Reverse camera remains ON when in Drive (vehicles manufactured before May 1, 2018) - Average fuel economy displays 99.9 MPG - Display screen flickers at higher ambient interior temperatures - SXM Info Apps (Weather, Stocks, Fuel Prices) inoperative ACTION 1. Refer to page 4, step 8 in the SERVICE PROCEDURE to confirm an update applies to the Display Control Unit (DCU) of the vehicle being worked on. - Confirmation is determined by comparing the DCU part number with those listed in Table on page 5. 2. If this bulletin applies, update the DCU software. - See REQUIRED SPECIAL TOOL on page 2. NOTE: The updated software resolves the items above along with improving software stability.
ITB18-039
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
ITB15-026b
Service Bulletin/Repair Instructions
INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
ITB12-011l
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.