Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011Q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-040
Service Bulletin/Repair Instructions
3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. INFINITI Connection with InTouch⢠Services are no longer available on the APPLIED VEHICLES listed above.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC835 - R1606 Ca
Service Bulletin/Repair Instructions
R1606 Occupant Classification System (OCS) Campaign Quality Review ***** Retailer Announcement ***** INFINITI is committed to the safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1606). If the VIN displays QA campaign ID PC835, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIâs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC835. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. ⢠Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.
ITB10-037E
Service Bulletin/Repair Instructions
RADIO PRESETS / CLIMATE CONTROL SETTINGS / NAVIGATION SETTINGS CHANGE WITH INTELLIGENT KEY MEMORY This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-017B
Service Bulletin/Repair Instructions
2014 â 2015 Q50; CONFIGURING INFINITI INTOUCH SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-021B
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-059B
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK INTERMITTENTLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB13-057B
Service Bulletin/Repair Instructions
2013 JX35, 2014-2015 Q50 & QX60; ONE OR BOTH INTELLIGENT KEYS LOST PRIOR TO CUSTOMER DELIVERY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB17-005A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
ITB12-041D
Service Bulletin/Repair Instructions
SIRIUSXM SATELLITE RADIO / WEATHER / TRAFFIC / TRAVEL LINK ACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB13-026L
Service Bulletin/Repair Instructions
2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-041A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB11-003F
Service Bulletin/Repair Instructions
NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011P
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-005a
Service Bulletin/Repair Instructions
CLOCK, AUDIO, HVAC OR NAVIGATION SETTINGS INTERMITTENTLY CHANGE ON THEIR OWN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-009a
Service Bulletin/Repair Instructions
INFINITI; THEFT ALARM TRIGGER HISTORY FUNCTION This bulletin is no longer active. Please discard previous versions of ITB16-009.
ITB14-043b
Service Bulletin/Repair Instructions
CUSTOMER SATISFACTION INITIATIVE 2014 Q50 AUDIO SOFTWARE UPDATE Service Campaign ID # P4248 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # P4248. Please discard all previous versions of ITB14-043.
EXPIRATION NOTIF
Service Bulletin/Repair Instructions
Expiration Notification - 2G Telematics Hardware Replacement Campaign Summary In 2016, INFINITI launched a Client Satisfaction Initiative (CSI) that provided clients with an opportunity to update the Telematics Control Unit (TCU) in vehicles equipped with a TCU designed to connect to the 2G cellular network. AT&T stopped accepting enrollments on the 2G cellular network, and discontinued its 2G cellular network coverage on December 31, 2016. Once the 2G cellular network was discontinued, there was no access to the INFINITI Connection features without a TCU hardware upgrade. Because AT&T will shut down its 3G network on December 31, 2021, INFINITI is discontinuing this Client Satisfaction Initiative to upgrade from 2G to 3G compatible hardware effective immediately. 3G services will continue to be provided until December 31, 2021. Vehicles equipped with a TCU that connects to the 3G cellular network will have no access to the INFINITI Connection features, including Emergency Calling and Automatic Collision Notification after that time. What Retailers Should Do Service Comm will deactivate PC451, PC452 and PC454 on any VINs on December 22, 2020. No further retailer action is required.
ITB17-007a
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT Customer Satisfaction Initiative ID # PC451, PC452 and PC454 are no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC451, PC452 or PC454. ï· Please discard all previous versions of ITB17-007.
ITB15-024a
Service Bulletin/Repair Instructions
2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB17-042c
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB20-003
Service Bulletin/Repair Instructions
2014-2020 Q50 AND 2017-2020 Q60; TPMS SENSOR LEAKING AIR IF YOU CONFIRM The vehicle has the original equipment wheels and TPMS sensors (tire pressure sensors) installed. AND The owner states that one or more tires has a continuous air leak or looses air pressure multiple times over a 30 day period (approximatively 1 psi every 3 days). NOTE: The TPMS warning lamp may be ON (not flashing) with one or more of the following DTCs stored: ï· - C1704, C1705, C1706, C1707, C1730, C1731, C1732, C1733 ï· - If the TPMS warning lamp is flashing for more than one (1) minute this bulletin does not apply. Refer to the Electronic Service Manual (ESM) for further diagnostic information. ACTION 1. Confirm that air is leaking between the tire pressure sensorâs valve stem and valve nut of the affected wheel/tire. 2. Replace the valve stem washer/seal and the valve nut and then torque to the new specification.
ITB13-026k
Service Bulletin/Repair Instructions
2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-040
Service Bulletin/Repair Instructions
2014-2015 Q50; MIL ON WITH DTC P0720 AND MAY HAVE HARSH SHIFTING AND/OR LACK OF POWER SERVICE INFORMATION If DTC P0720 OUTPUT SPEED SENSOR is stored, follow the diagnostic procedure in the ESM. If the diagnosis leads to output speed sensor replacement, replace the control valve. Do NOT replace the output speed sensor. ï· - Refer to the ESM for control valve replacement: TRANSMISSION DRIVELINE> TRANSAXLE TRANSMISSION > 7 AT: RE7R01A > REMOVAL AND INSTALLATION > CONTROL VALVE TCM. HINT: The vehicle may also have harsh shifting and/or lack of power.
ITB12-011o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on the next page. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
ITB13-026J
Service Bulletin/Repair Instructions
2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB19-005
Service Bulletin/Repair Instructions
CLOCK, AUDIO, HVAC OR NAVIGATION SETTINGS INTERMITTENTLY CHANGE ON THEIR OWN This bulletin applies only to vehicles equipped with INFINITI InTouch (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with INFINITI InTouch?, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-042b
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB12-011m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-026i
Service Bulletin/Repair Instructions
2014-2017 INFINITI VEHICLES; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-001
Service Bulletin/Repair Instructions
CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 - (CHASSIS CONTROL BRAKE SYSTEM) - C1B90-00 - (DIRECT ADAPTIVE STEERING SYSTEM) - C1B92-00 - (BRAKE CONTROL SYSTEM) - C1B93-00 - (ENGINE/HEV SYSTEM) - C1B94-00 - (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
ITB17-026b
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
Revision 1-IEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
ITB18-039
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
REVISION 4-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative UPDATE October 12, 2018 Please discard earlier versions of this bulletin. The announcement from February 17, 2017 has been revised to include: - ~397 retailed vehicles have been added to campaign ID PC454
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
IPSB18-218 Retai
Service Bulletin/Repair Instructions
DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
ITB12-011l
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
ITB17-026a
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL IF CUSTOMER REPORTS: Customer routinely experiences difficulty fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.
ITB13-044f
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.
ITB18-021
Service Bulletin/Repair Instructions
DAST CALIBRATION (MODE1) INCOMPLETE OR C13E9-00/C13EB-00 UNABLE TO ERASE This bulletin applies only to vehicles equipped with Direct Adaptive Steering (DAST). SERVICE INFORMATION This bulletin has information for two services for which a technician may need additional help: - While performing DAST CALIBRATION (MODE1), the calibration may stop or will not start. - DTC C13E9-00 (BOOTING ANGLE PROCESSING) and C13EB-00 (BOOTING ANGLE PROCESSING) are stored and cannot be erased. The above conditions may indicate that DAST CALIBRATION (MODE1) was not performed correctly or was not completed correctly. Use the SERVICE PROCEDURE in this bulletin as an aid to correctly perform and complete DAST CALIBRATION MODE 1. NOTE: - The SERVICE PROCEDURE in this bulletin does not contain all of the required steps. - The Electronic Service Manual (ESM) must be used together with this bulletin. - This bulletin contains additional clarification as an aid to perform DAST CALIBRATION MODE 1.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB13-052b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB11-005d
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB03-051L
Service Bulletin/Repair Instructions
HEADLAMP FOGGING This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
IPSB15-286a
Service Bulletin/Repair Instructions
DBS Enhancement ? Checking Inventory for Open Campaigns UPDATE February 26, 2018 Please discard earlier versions of this bulletin The announcement from December 21, 2015 has been revised to include: 1. New functionality for identifying stop sales and parts restrictions for vehicles in dealer inventory 2. RDR warning messages when vehicles affected by a stop sale are submitted for retail delivery
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
ITB12-011k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
ITB13-026h
Service Bulletin/Repair Instructions
DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. The Applied Vehicles section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB18-003
Service Bulletin/Repair Instructions
REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
ITB12-011j
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.
ITB13-026g
Service Bulletin/Repair Instructions
DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. The Applied Vehicles section and Part 1 of the Service Procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB09-039e
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-009a
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g
Service Bulletin/Repair Instructions
BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
ITB12-011i
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with factory Navigation system. This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.
ITB12-011h
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with factory Navigation system. This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.
ITB11-005c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-030b
Service Bulletin/Repair Instructions
2014-2016 Q50; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 20 and 22 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-042a
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-030a
Service Bulletin/Repair Instructions
2014-2016 Q50; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB16-021a
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
P7331
Service Bulletin/Repair Instructions
Disabling the 2G TCU Voluntary Service Campaign ***** Campaign Summary ***** Infiniti is conducting a Voluntary Service Campaign to disable (turn off) the 2G Telematics Control Unit (?2G TCU?). The subject QX56/QX80, JX35/QX60, M37/M56/Q70, and 2014-15 Q50 vehicles are equipped with Continental GEN1 TCU devices transmitting at 2/2.5G (GSM/GPRS/UMTS) frequencies and are designed to work with 2G cellular service. The 2G cellular service is no longer active in the United States. The subject 2G TCUs are no longer connected to telematics services and no longer perform any function in the affected vehicles. This campaign is being performed out of an abundance of caution to help safeguard against potential cybersecurity issues. - All eligible vehicles that enter the service department for any reason should have the subject 2G TCU deactivated. This campaign will be performed at no charge to the client for parts and labor. - Vehicles that have been upgraded to 3G TCUs are not subject to this campaign. - For clients interested in the 3G TCU upgrade as opposed to deactivation, please refer to ITB17-007 (PC451, PC452, or PC454)
ITB17-041
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION INTRODUCTION Infiniti is conducting a Voluntary Service Campaign (in the U.S. ONLY) on certain specific 2013-2016 Infiniti vehicles equipped with 2G Telematics Hardware to disable the 2G Telematics Control Unit (TCU). The 2G cellular service is no longer active in the United States and the subject TCUs are no longer connected to telematics services (Infiniti ConnectTM) and no longer perform any function in the affected vehicles. This campaign is being performed out of abundance of caution to help prevent potential cybersecurity issues. - Applied vehicles equipped with the 2G Telematics Control Unit (TCU) that enter the service department for any reason should have the subject TCU deactivated. This campaign will be performed at no charge to the customer for parts or labor. - For customers interested in the TCU update as opposed to deactivation, please refer to ITB17-007. IDENTIFICATION NUMBER Infiniti has assigned identification number P7331 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer?s inventory.
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.
ITB17-015
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
ITB17-030
Service Bulletin/Repair Instructions
2014-2016 Q50; OCCUPANT CLASSIFICATION SYSTEM RETROFIT SERVICE INFORMATION The information in this bulletin is provided for customers who have concerns with their vehicle's Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on.
ITB17-026
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
ITB17-018
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
REVISION 3-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from January 3, 2017 has been revised to include: - Campaign repair bulletin, ITB17-007 has been developed and is now available on NNAnet, and ASIST. Please discard earlier versions of this bulletin.
ITB17-007
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT This bulletin applies to vehcile equipped with navigation systems only. SERVICE INFORMATION On February 26, 2016 Infiniti announced that it was sending a reminder notification to clients affected by AT&T?s planned discontinuation of the 2G cellular network. In June 2016, Infiniti communicated instructions to retailers to update new vehicles in their inventory with 3G compatible telematics control units. At this time, Infiniti is beginning the process of making 3G compatible hardware available to owners of affected vehicles as identified above. This upgrade may require an owner to make a co-payment in order to receive the 3G hardware update. Please refer to the Claims Information below to determine if an owner co-pay is required. This client satisfaction initiative includes both the hardware upgrade and a complimentary one-year subscription to Infiniti Connection Plus telematics service; this does not apply to PC454 (see page 2 for details). You MUST use Service Comm to confirm bulletin Applicability. NOTE: - Vehicle eligibility will be viewed on the second page of Service Comm. This activity is not displayed on the main page of Service Comm because it is optional for customers to participate. - Vehicles without Navigation are ineligible as they are not equipped with TCUs. Retailer?s Responsibility It is the retailer?s responsibility to check SERVICE COMM using the appropriate Service Comm I.D. for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB16-037c
Service Bulletin/Repair Instructions
2014-2016 Q50; INCORRECT DIFFERENCE IN HVAC VENT TEMPERATURES This bulletin has been amended throughout. Discard all previous versions of this bulletin.
REVISION 2-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from November 3, 2016 has been revised to include: - 283B0-3JA6A is the part number being used for all vehicles, except Q50 o This part supersedes the previous part (283B0-3JA5A). Retailers may continue to use the previous part until existing stock is exhausted. - 283B0-3JA7A is used for Q50 - These parts are not restricted and can be ordered through normal process Please discard previous versions of this announcement.
ITB13-052a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB16-047
Service Bulletin/Repair Instructions
INFINITI; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
ITB16-037b
Service Bulletin/Repair Instructions
2014-2016 Q50; AIR MIX DOOR MOTOR LH SERVICE INFORMATION This bulletin has been amended throughout. Discard all previous versions of this bulletin.
ITB16-042a
Service Bulletin/Repair Instructions
2014-2017 Q60 AND Q50; POWER WINDOWS DO NOT OPERATE CORRECTLY SERVICE INFORMATION If power is interrupted to the power window system, it may cause one or more of the following symptoms to occur on one or more power windows: - AUTO-UP does not work, but window will move up and down with manual operation of the switch. - When door is opened (only applies to Q60), window will lower a small amount (normal operation) but will not raise when door is closed. - Window will move down when operating the window switch, but will not move up. NOTE: - If any of the above symptoms should occur, it may indicate that Window Initialization is needed (see page 2). Initialization should be done before attempting any repairs. - If needed, refer to the applicable Electronic Service Manual (ESM) to perform electrical diagnosis. - After electrical repairs to the vehicle (including repairs to the power windows), make sure to perform the Window Initialization and Anti-pinch Function Check procedures on page 2.
ITB13-026f
Service Bulletin/Repair Instructions
DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. Modifications have been made to include 2017 Q50, Q50 Hybrid, Q60, QX30, QX60 and QX60 Hybrid vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
REVISION 1-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from September 2, 2016 has been revised to include: - The telematics upgrade for 2014-15 Q50 is now available. The procedure and part information has been added to this announcement.. - Second page of Service Comm is not VIN specific, service personnel should check vehicle repair history prior to offering clients an opportunity to upgrade - In lieu of repair history, TCU version can be checked on the information screen (see page 2) Please discard previous versions of this announcement.
ITB12-011g
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-037a
Service Bulletin/Repair Instructions
2014-2016 Q50; INCORRECT DIFFERENCE IN HVAC VENT TEMPERATURES The information in the previous version of this bulletin is no longer valid. Please discard the previous version of this bulletin.
ITB16-037
Service Bulletin/Repair Instructions
2014-2016 Q50; INCORRECT DIFFERENCE IN HVAC VENT TEMPERATURES IF YOU CONFIRM: THE DRIVER SIDE VENT IS WARMER BY 10°F OR MORE THAN THE PASSENGER SIDE WITH THE HVACS DUAL TEMP MODE SELECTED AND THE A/C SET ON BOTH SIDES AT 60°F. - THIS INCIDENT, IF IT SHOULD OCCUR, MAY BE INTERMITTENT. ACTION: USING THE SERVICE PROCEDURE IN THIS BULLETIN, REPLACE THE AIR MIX DOOR MOTOR LH AND THE AIR MIX DOOR LEVER LH WITH THE ONES FROM THE PARTS INFORMATION SECTION OF THIS BULLETIN.
ITB12-011F
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION VEHICLES EQUIPPED WITH FACTORY NAVIGATION SYSTEM THIS BULLETIN HAS BEEN AMENDED. MODIFICATIONS HAVE BEEN MADE TO INCLUDE QX30. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
ITB16021
Service Bulletin/Repair Instructions
2014 - 2015 Q50; THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED
ITB11021B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.
ITB09041A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
ITB09063B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
ITB16-014
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB15021A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
EL13-023E
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB13026E
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the Display Control Unit (DCU) needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure of this bulletin. See this bulletin for further detail.
ITB16014
Service Bulletin/Repair Instructions
IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 2. If it applies, reprogram the ECM. See this bulletin for further detail.
ITB15018A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: "Brake Judder" during braking, especially when braking at highway speeds. Symptoms of "brake judder": - steering wheel shake - body vibration - brake pedal pulsation IMPORTANT NOTES: If any symptom above occurs when cruising or coasting (not braking), it is not "Brake Judder" and may be tire/wheel related. DO NOT CONFUSE "Brake Judder" with the rapid consistent-speed pedal pulsation that may be felt and only occurs when ABS is activated during hard braking or on slippery road surfaces. ACTION: 1. Inspect the front brake rotors to determine if "machining" ("turning") is possible or if replacement is necessary. 2. Replace both pad pins in both front 4-piston calipers (see PARTS INFORMATION). 3. Replace the front brake pads (see PARTS INFORMATION). See this bulletin for further detail.
ITB03051J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
ITB15034B
Service Bulletin/Repair Instructions
INTRODUCTION Infiniti is conducting a Voluntary Service Campaign on certain specific 2014-2015 Q50 Hybrid cold state vehicles (listed below) to replace the 12 volt battery. This service will be performed at no cost to the customer for parts or labor. This campaign will apply to vehicles in the following States, only: Colorado, Connecticut, Idaho, Illinois, Indiana, Iowa, Kansas, Maine, Massachusetts, Michigan, Minnesota, Montana, Nebraska, Nevada, New Hampshire, New York, North Dakota, Ohio, Pennsylvania, South Dakota, Utah, Vermont, Washington, Wisconsin, Wyoming. IDENTIFICATION NUMBER Infiniti has assigned identification number P5326 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. See this bulletin for further detail.
P5323B
Service Bulletin/Repair Instructions
This announcement has been updated to include New battery replacement instructions due to the parts shortage New Claims Information
P5326B
Service Bulletin/Repair Instructions
This announcement has been updated to include New battery replacement instructions due to the parts shortage New Claims Information
ITB16006
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing the front sonar parking sensor for potentially unwanted activation (e.g. sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if: The front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.
ITB09039C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Infiniti dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
P5323A
Service Bulletin/Repair Instructions
12-volt batteries necessary for replacement under P5323 or P5326 are currently on back order. We expect additional parts to arrive in late April.
P5326A
Service Bulletin/Repair Instructions
12-volt batteries necessary for replacement under P5323 or P5326 are currently on back order. We expect additional parts to arrive in late April.
PC405A
Service Bulletin/Repair Instructions
Infiniti would like to remind retailers that the ?Q50 Client Appreciation? program (PC405) will expire on January 30th, 2016. Vehicles serviced on or after that date will no longer be eligible for the program.
ITB16009
Service Bulletin/Repair Instructions
SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG See this bulletin for further details.
ITB16005
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
P5323OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P5326OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P5323
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P5326
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
ITB13007A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.
ITB09015G
Service Bulletin/Repair Instructions
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
ITB14059A
Service Bulletin/Repair Instructions
IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
P5325OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain MY 2014-15 Q50 vehicles equipped with Direct Adaptive SteeringTM (DAS) system to update the DAS software to the latest production standards
P5325
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain MY 2014-15 Q50 vehicles equipped with Direct Adaptive SteeringTM (DAS) system to update the DAS software to the latest production standards
PC405
Service Bulletin/Repair Instructions
Beginning October 14th, 2015 Infiniti USA will be asking retailers to provide additional client satisfaction activities on specific vehicles identified through Service Comm as PC405 ?Q50 Client Appreciation?.
ITB11042D
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
ITB13039A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
ITB15027
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the glove box is removed for any reason (for example, installing an accessory kick plate, replacing an in-cabin microfilter, etc.), verify the trunk release power cancel switch operates normally after installing the glove box. See this bulletin for further detail.
ITB11011A
Service Bulletin/Repair Instructions
SERVICE INFORMATION For QX60 Hybrid Vehicles, go to page 4. Q50, Q70, and M35 Hybrid Vehicles The internal combustion (IC) engine in the Q50, Q70, and M35 Hybrid vehicles is started using a high voltage motor that is integrated into the transmission. The high voltage motor gets its power from the high voltage Lithium-Ion (Li-ion) battery that is mounted between the trunk room and the rear seat. The Li-ion battery cannot be recharged using an external battery charger; therefore it is very important that the battery state of charge (SOC) is properly maintained during extended storage periods. Action must to be taken in order to prevent excessive discharge of the high voltage Li-ion battery during an extended storage period. If the reserve capacity of the Li-ion battery is not sufficient, the hybrid system cannot be started. Perform the Battery Discharge Prevention During Extended Storage procedure in this bulletin once a month (every 30 days). NOTE: A discharged high voltage Li-ion battery is not a warrantable issue. See this bulletin for further detail.
ITB14028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
ITB-14-051
Service Bulletin/Repair Instructions
INFINITI: ON SOME VEHICLES, THE FORWARD COLLISION WARNING (FCW) MALFUNCTION HAS BEEN OR IS ON AND FLUID LEVEL FOR BRAKES IS NORMAL AND THE ABS CONTROL UNIT NEEDS PROGRAMMING, PER SERVICE PROCEDURE. MODEL 2013-14 JX35, QX60, 2014-15 Q50. *PE UPDATED 9/10/15. *PE
ITB14051A
Service Bulletin/Repair Instructions
IF YOU CONFIRM All of the following: The FCW (Forward Collision Warning) malfunction is ON or reported to have been ON, and DTC C1A27 (ECD POWER SUPPLY CIRCUIT) is stored (Past or Current), and the brake fluid level is normal. NOTE: C1A27 is an ICC (Intelligent Cruise Control) DTC. ACTION Reprogram the ABS control unit (ABS) per the Service Procedure in this bulletin. - Part of the Service Procedure, step 20 on page 8, is a confirmation that reprogramming is needed to resolve the incident shown in Figure A and B on page 1. See this bulletin for further detail.
ITB13054D
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is ON with DTC P0101 and/or P010B (MAF SEN/CIRCUIT-B1/B2) and there are no drivability issues. ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. NOTE: If this bulletin does apply (the ECM needs to be reprogrammed), do NOT replace the mass air flow sensor(s). See this bulletin for further detail.
ITB15001A
Service Bulletin/Repair Instructions
IF YOU CONFIRM The steering wheel makes a faint squeaking/ticking noise when turned left or right. NOTE: Due to the faint nature of this noise it may be necessary to lift front wheels off of the ground so that it can be isolated. ACTION Remove driver?s side airbag and apply felt tape with the SERVICE PROCEDURE starting on page 2. See this bulletin for further detail.
ITB10037D
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
ITB15025
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
ITB15020
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
ITB15016
Service Bulletin/Repair Instructions
SERVICE INFORMATION If you confirm there is a need to replace the combination meter front cover (lens) on an Applied Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.
ITB10062E
Service Bulletin/Repair Instructions
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
ITB99043G
Service Bulletin/Repair Instructions
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
ITB14039B
Service Bulletin/Repair Instructions
IF YOU CONFIRM A strong sulfur like odor is coming from the Moonroof drain hoses after a hot soak (after sitting with doors and windows closed). - Odor is most noticeable if the Moonroof shade is left closed while the vehicle sits in the direct sunlight and then after a hot soak the Moonroof shade is opened. NOTE - The Moonroof drain hoses MUST be the cause of the strong sulfur like odor for this bulletin to apply. ACTION Replace the Moonroof drain hoses with the Service Procedure starting on the next page AND deodorize with an ozone generator as needed AND THEN replace in-cabin microfilter. See this bulletin for further detail.
ITB15007
Service Bulletin/Repair Instructions
IF YOU CONFIRM A power window auto-up does not work for one or more power windows. ACTION Replace the left front (driver) door finisher with the new one listed in the Parts Information. While replacing the door finisher, also replace the main power window switch. See this bulletin for further detail.
ITB15004
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is ON after the engine has been idling a while and one or both of the following DTCs are found stored in the ECM: - P0171 (FUEL SYS-LEAN-B1) - P0174 (FUEL SYS-LEAN-B2) ACTION: 1. Confirm this bulletin applies. - Compare the vehicle?s current ECM part number to those listed in Table A (see page 5). 2. If the ECM part number does not match one listed in Table A, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. 3. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
ITB00031D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
ITB13002A
Service Bulletin/Repair Instructions
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
ITB11003E
Service Bulletin/Repair Instructions
SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
ITB12041C
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather or Travel Link OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
ITB13047A
Service Bulletin/Repair Instructions
SERVICE INFORMATION In an Applied Vehicle, maintenance reminders (when set) are displayed in the following two locations: - Meter (Information Display) - APPS Screen (Maintenance Note App) Maintenance reminders set in the meter settings will display on the Information Display. Maintenance reminders set in the Maintenance Note App will display on the APPS screen. See this bulletin for more detail.
ITB14017A
Service Bulletin/Repair Instructions
SERVICE INFORMATION MULTI A/V Configuration using CONSULT-III plus (C-III plus) There are many configurations of the Infiniti InTouch system. Typically, if the MULTI A/V is not configured properly on a navi equipped vehicle, you will see a clock with no hands on the upper display. If in a situation where the MULTI A/V needs to be manually configured. Please see this bulletin for further details.
ITB13057A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ----- Page 2 - Two (2) Intelligent Keys Are Lost ----- Page 3 See this bulletin for further detail.
ITB-14-043
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON SOME VEHICLES, A PRODUCT UPDATE, FOR IN TOUCH AUDIO SYSTEM SOFTWARE, IS BEING OFFERED AND IS DESIGNED TO IMPROVE FUNCTIONALITY OF IN TOUCH SYSTEM. MODEL 2014 Q50. *PE UPDATE 12/12/14. *PE UPDATED 3/31/15. *PE
ITB14-043A
Service Bulletin/Repair Instructions
INFINITI: 2014 Q50(V37) : OWNERS ARE OFFERED TO HAVE THE AUDIO SYSTEM SOFTWARE UPGRADED. INFINITI DEALERS ARE PERFORMING THIS UPGRADE AT NO COST. *LJ
ITB14043A
Service Bulletin/Repair Instructions
SERVICE INFORMATION As part of Infiniti?s commitment to continually improve both the quality and durability of our products, Infiniti is offering owners of the 2014 Q50 the opportunity to have their vehicle?s InTouch Audio system software upgraded with a production change that has been incorporated in the Q50 manufactured after their vehicle was produced. With this Q50 Customer Satisfaction Initiative, all Infiniti retailers are authorized to perform this service upgrade at no cost to the customer for parts or labor. This Customer Satisfaction Initiative is intended to improve the overall driving experience, and to add additional features, to maximize the driving experience of Q50 owners. See this bulletin for further details.
P4248A
Service Bulletin/Repair Instructions
Infiniti is offering owners of the 2014 Q50 the opportunity to have their vehicle?s InTouch Audio system software upgraded with a production change that has been incorporated in the Q50 manufactured after their vehicle was produced.
ITB14057
Service Bulletin/Repair Instructions
SERVICE INFORMATION After replacement of a CAN Gateway Module, the new module must be configured with the correct part number to complete the repair. Use the part number listed in this bulletin for all trim levels of the Applied Vehicles. See this bulletin for further details.
ITB14056
Service Bulletin/Repair Instructions
SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
ITB14055
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
ITB13038B
Service Bulletin/Repair Instructions
IF YOU COFIRM The driver and front passenger doors will not unlock using the one-touch door unlock sensor, and the Touch Sensitive Door Sensor feature is set to ON. ACTION 1. Use Signal Tech-II to check/test signals from the BCM and the Intelligent Key. 2. Replace the Intelligent Key or BCM based on the test result. See this bulletin for further detail.
ITB14045
Service Bulletin/Repair Instructions
IF YOU CONFIRM One or both steering wheel switch chrome finishers on an Applied Vehicle has come off. ACTION Follow the procedure in this bulletin to install the new steering wheel switch chrome finisher(s) listed in the Parts Information section. NOTE - Do not replace the steering wheel assembly for this incident, if it should occur. See this bulletin for further detail.
P4248OL
Service Bulletin/Repair Instructions
Infiniti is offering owners of the 2014 Q50 the opportunity to have their vehicle?s InTouch Audio system software upgraded with a production change that has been incorporated in the Q50 manufactured after their vehicle was produced.
P4249OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on 2014 Q50 and Q50 Hybrid vehicles to install a Fuse Box B+ Terminal Cover.
P4248
Service Bulletin/Repair Instructions
Infiniti is offering owners of the 2014 Q50 the opportunity to have their vehicle?s InTouch Audio system software upgraded with a production change that has been incorporated in the Q50 manufactured after their vehicle was produced.
P4249
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on 2014 Q50 and Q50 Hybrid vehicles to install a Fuse Box B+ Terminal Cover.
ITB-14-047
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A FUSE BOX B+ TERMINAL COVER IS BEING INSTALL ON CERTAIN HYBRID VEHICLES. MODEL 2014 Q50, Q50 HYBRID. *PE
ITB14047
Service Bulletin/Repair Instructions
INTRODUCTION Infiniti is conducting a Voluntary Service Campaign on 2014 Q50 and Q50 Hybrid vehicles to install a Fuse Box B+ Terminal Cover. This service will be performed at no charge for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number P4249 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign.
ITB14046
Service Bulletin/Repair Instructions
SERVICE INFORMATION When performing Direct Adaptive Steering (DAST) Calibration (Mode 1): Always use an alignment rack with the front wheels positioned on the turntables and the pins removed. The front wheels must be allowed to move freely. DO NOT perform DAST Calibration (MODE 1) with the front wheels in any other position then listed above. To prevent damaging the spiral cable during DAST Calibration (MODE 1), follow instruction in the ESM. See this bulletin for further detail.
ITB14044
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The rear brakes squeak when braking while the brakes are at normal operating temperature AND the applied vehicle is equipped with single piston rear brake calipers. ACTION: Replace the hardware on both rear brake calipers with the kit listed in PARTS INFORMATION in this bulletin. NOTE: Machining of the rotors is not necessary. Refer to the Electronic Service Manual (ESM), section BR-Brake System, for removal and installation. See this bulletin for further detail.
ITB-14-042
Service Bulletin/Repair Instructions
INFINITI: INFORMATION REGARDING TWO STAIN GAUGE OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSORS AND OPERATION EXPLANATION OF DIFFERENT RESPONSE TO OCCUPANT SEATING POSTURE. MODEL 2013-2014 JX, QX60, QX50. *PE
ITB14038
Service Bulletin/Repair Instructions
SERVICE INFORMATION When replacing a BCM for any reason and the original BCM?s configuration cannot be accessed with CONSULT-III plus (C-III plus), the new BCM must be manually configured. Configuration settings are not "spelled out" in C-III plus. For example, under Intelligent Key Type the designation "0" is used in place of "without I-KEY". Currently, the Electronic Service Manual (ESM) does not have a definition chart. The ESM will be updated with this information. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the chart on the next page to assist in performing a manual configuration on the applied vehicles listed above. See this bulletin for further detail.
ITB14029
Service Bulletin/Repair Instructions
IF YOU CONFIRM Using chassis ear, a rattle noise coming from the rear propeller shaft center bearing under the following conditions - Light to moderate acceleration, and between 2,000 and 2,800 rpm. ACTION Replace the rear propeller shaft with the new one (new style) listed in the Parts Information of this bulletin. See this bulletin for further detail.
ITB10029A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
ITB14026
Service Bulletin/Repair Instructions
IF YOU CONFIRM When initially applying the brakes: * The brakes are too sensitive and may unexpectedly grab with a lower than normal pedal pressure. AND * Only occurs at ambient temperatures below 40°F (4°C). NOTE: This Service Procedure will not change or affect any braking sensitivity above 40°F (4°C). ACTION 1. Bleed the brake hydraulic system. 2. Reprogram the Brake Controller. 3. Erase all DTCs present. Please see this bulletin for further details.
SM442014
Service Bulletin/Repair Instructions
Fuel sender
ITB14024
Service Bulletin/Repair Instructions
SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
ITB14020
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
ITB14019
Service Bulletin/Repair Instructions
IF YOU CONFIRM: While driving, the Vehicle Dynamic Control (VDC) activates when conditions do not call for VDC activation (VDC activation is not needed). ACTION: 1. Check F/B ANGLE 2 in EPS/DAST3. 2. If needed, perform Calibration and Confirmation Procedure. See this bulletin for further detail.
ITB14014
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.
ITB14012
Service Bulletin/Repair Instructions
SERVICE INFORMATION When a BCM is replaced for any reason, TPMS (Tire Pressure Monitor System) configuration must be performed. TPMS configuration is in addition to any other BCM configurations that may be performed. If TPMS configuration is not performed, TPMS transmitter ID registration will not complete. Follow the Service Procedure in this bulletin to perform TPMS configuration. See this bulletin for further detail.
ITB-14-004
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE CURRENT PRODUCTION LEVEL OF THE INFINITI INTOUCH SYSTEM SOFTWARE IS BEING UPDATED. MODEL 2014 Q50, Q50 HYBRID. *PE UPDATED 3/20/14. *PE
ITB-14-005
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE INFINITI INTOUCH SYSTEM ALLOWS SOFTWARE UPDATES TO BE INSTALLED TO CURRENT PRODUCTION LEVEL. MODEL 2014 Q50, Q50 HYBRID. *PE UPDATED 3/14/14. *PE
ITB13056A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is ON and one or both of the following DTCs are found stored in the ECM: - P0139 (heated oxygen sensor 2 (B1) circuit slow response) - P0159 (heated oxygen sensor 2 (B2) circuit slow response) ACTION: 1. Confirm this bulletin applies. - Compare the vehicle's current ECM part number to those listed in Table A (see page 4). 2. If the ECM part number does not match one listed in Table A, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. 3. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
PC262
Service Bulletin/Repair Instructions
Beginning February 11th, 2014 Infiniti USA will be asking retailers to provide additional client satisfaction activities on specific vehicles identified through Service Comm as PC262 ?Q50 Quality Assurance?.
ITB-14-006
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE DIRECT ADAPTIVE STEERING (DAST), IS BEING REPROGRAMMED. MODEL 2014 Q50, Q50 HYBRID. *PE UPDATED 2/24/14. *PE
ITB-14-007
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. REPROGRAMMING AND RECALIBRATING THE DIRECT ADAPTIVE STEERING (DAST) ON CERTAIN VEHICLES. MODEL 2014 Q50, Q50 HYBRID. *PE UPDATED 2/24/14. *PE
ITB-14-009
Service Bulletin/Repair Instructions
INFINITI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE DIRECT ADAPTIVE STEERING SYSTEM (DAST) CONTROL MODULES, ON CERTAIN VEHICLES, ARE BEING REPLACED, REPROGRAMMED AND RECALIBRATED. MODEL 2014 Q50. *PE UPDATED 2/24/14. *PE
ITB08024C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
P4201OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to reprogram the Direct Adaptive Steering (DAST).
P4202OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to reprogram and calibrate the Direct Adaptive Steering (DAST).
P4203OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to replace 3 control units, reprogram, and calibrate the Direct Adaptive Steering (DAST).
P4204OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to replace 3 control units, reprogram, calibrate and reset the Direct Adaptive Steering (DAST).
P4205OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to update the Infiniti InTouch software and Sirius XM Activation Signal Refresh.
P4206OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to update the Infiniti InTouch software.
P4201
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to reprogram the Direct Adaptive Steering (DAST).
P4202
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to reprogram and calibrate the Direct Adaptive Steering (DAST).
P4203
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to replace 3 control units, reprogram, and calibrate the Direct Adaptive Steering (DAST).
P4204
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to replace 3 control units, reprogram, calibrate and reset the Direct Adaptive Steering (DAST).
P4205
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to update the Infiniti InTouch software and Sirius XM Activation Signal Refresh.
P4206
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 Q50 and Q50 Hybrid vehicles to update the Infiniti InTouch software.
ITB14002
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
ITB13040A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The vehicle information display stays ON with the message "Warning No Key Detected" even though the ignition is OFF, doors are closed, transmission is in Park, and the Intelligent Key is removed from the vehicle. ACTION: Perform A/T POSITION ADJUSTMENT per the Service Manual. - In the TM section of the Service Manual, go to A/T POSITION, and perform the ADJUSTMENT procedure. - Make sure the incident is resolved. See this bulletin for further detail.
ITB14001
Service Bulletin/Repair Instructions
SERVICE INFORMATION If for any reason the lower touch screen display, NAVI control unit, or AV control unit needs to be replaced, refer to the Electronic Service Manual (ESM) for replacement procedure, if needed. After replacement, always refer to (and use as it applies) the "Infiniti InTouch Software Update" General Procedure. See this bulletin for further information.
ITB-13-046
Service Bulletin/Repair Instructions
INFINITI: INFORMATION PROVIDED REGARDING THE LOW POWER ASSIST FOR POWER STEERING REPAIR, ON SOME VEHICLES. MODEL 2014 Q50. *PE
ITB-13-034-A
Service Bulletin/Repair Instructions
INFINITI: INFORMATION PROVIDED REGARDING SIGNAL TECH II, BEING USED, TO PERFORM TIRE PRESSURE MONITORING SYSTEM (TPMS) ID PROCEDURE REGISTRATION. MODEL 2014 Q50. *PE
ITB13034A
Service Bulletin/Repair Instructions
SERVICE INFORMATION As of the publication date of this bulletin, the 2014 Q50 and Q50 Hybrid require the use of CONSULT-III plus to perform the TPMS (Tire Pressure Monitoring System) ID registration procedure. TPMS ID registration can be performed using one of the following procedures: - Transmitter Activation tool (J-45295-A) with CONSULT-III plus (preferred method) - Signal Tech II (J-50190) with CONSULT-III plus NOTE: As of the publication date of this bulletin, Signal Tech II cannot be used on its own (without CONSULT-III plus) to perform TPMS registration. Software updates for Signal Tech II will be available at a later date. Use the TPMS ID registration instructions in this bulletin as needed. NOTE: Tire Pressure Sensor Activation Tool J-45295 will not work on the 2014 Q50 or Q50 Hybrid. See this bulletin for further detail.
ITB-13-044
Service Bulletin/Repair Instructions
INFINITI: THE INSTRUMENT CLUSTER HAS A WARNING INDICATOR, THAT ILLUMINATES, OF A LOOSE FUEL FILL CAP. MODEL YEARS 2012 AND UP. NO MODELS LISTED. *PE
P3258
Service Bulletin/Repair Instructions
Infiniti is conducting an update to the SiriusXM software on certain specific MY14 Q50 vehicles.
P3257A
Service Bulletin/Repair Instructions
Additional USBs shipped to all retailers for Q50 IT Gen 5 Product Performance Enhancement
ITB13029A
Service Bulletin/Repair Instructions
SERVICE INFORMATION: During the Pre-Delivery Inspection (PDI) test drive, you may experience the following conditions: - While driving straight the steering wheel is off-center, and - While driving straight, if you relax your grip on the steering wheel, the steering wheel will return to center and the vehicle will pull, as if making a turn. The above condition indicates that the Direct Adaptive Steering (DAST) needs to be trained (recalibrated). NOTE: Do not perform a wheel alignment for a steering wheel off-center or pull condition at PDI. See this bulletin for further detail.
ITB-13-039
Service Bulletin/Repair Instructions
INFINITI: SERVICE BULLETIN CONCERNING LOW TIRE PRESSURE WARNING SYSTEM INFORMATION. *JS
ITB07047D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Scratch Shield is a scratch-resistant clear coat which "heals" by itself when the vehicle gets a small scratch in the clear coat. If the scratch reaches the color base coat, however, it will not "heal". Scratch Shield was implemented for the first time in the U.S. with the 2008 EX35. NOTE: Scratch Shield is applied to body panels and fasicas only. Scratch Shield Label Vehicles equipped with Scratch Shield have a label (see Figure 1) which is typically located underneath the hood. Vehicles that DO NOT have the Scratch Shield label shown in Figure 1 are not equipped with Scratch Shield. See this bulletin for further detail.
ITB-13-033A
Service Bulletin/Repair Instructions
INFINITI: SOME VEHICLES MAY EXPERIENCE THE POWER STEERING LIGHT TO BE ON PAIRED WITH DTC C13EB AND C13E9. THE STEERING WHEEL MAY BE OFF-CENTER AND POWER STEERING WILL GO INTO REDUCED POWER ASSIST MODE. THIS IS DUE TO LOW BATTERY VOLTAGE CONDITION. *JS
ITB13033A
Service Bulletin/Repair Instructions
SERVICE INFORMATION: At engine start up, if a low 12 volt battery condition (approximately 8 volts) occurs with an Applied Vehicle, the following conditions may happen: * The Power Steering Warning Light is, or may have been ON. * DTC codes C13EB (DAST1, DAST2) and C13E9 (DAST1) may be stored as current or past. * Power steering will go to EPS mode (reduced power assist). Additionally, * The steering wheel may be off-center when starting to drive. Please see this bulletin for futher details.
ITB-92-069-D
Service Bulletin/Repair Instructions
INFINITI: DUE TO USE OF AFTERMARKET CHROMING OF ALLOY WHEELS, FOR SOME VEHICLES, THE STANDARDS ARE NO LONGER ARE MET AND ARE SERIOUSLY DAMAGED AND NOT GUARANTEE OR WARRANTY THE MODIFIED WHEELS OR PERFORMANCE. MODELS ALL. NO YEARS LISTED. *PE
ITB92069D
Service Bulletin/Repair Instructions
Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
P3237B
Service Bulletin/Repair Instructions
Infiniti has released an Owner?s Manual Supplement which revises or adds three (3) pages in the 2014 Infiniti InTouch Owner?s Manual.
P3237A
Service Bulletin/Repair Instructions
Infiniti is conducting a Retailer Service Action to reprogram the IT GEN5 software on certain specific MY14 Q50 vehicles.
ITB00024F
Service Bulletin/Repair Instructions
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
ITB04038A
Service Bulletin/Repair Instructions
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
P3237
Service Bulletin/Repair Instructions
Infiniti is placing certain specific 2014 Q50 vehicles in retailer inventory on a temporary QA Hold.