Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011Q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008D
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008C
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008B
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-015B
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB17-005A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
ITB12-041D
Service Bulletin/Repair Instructions
SIRIUSXM SATELLITE RADIO / WEATHER / TRAFFIC / TRAVEL LINK ACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB10-017E
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT REQUIRES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-003F
Service Bulletin/Repair Instructions
NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011P
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-042a
Service Bulletin/Repair Instructions
2013 M AND 2014-2017 Q70; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH® HANDS-FREE PHONE FEATURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-007a
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT Customer Satisfaction Initiative ID # PC451, PC452 and PC454 are no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC451, PC452 or PC454. ï· Please discard all previous versions of ITB17-007.
ITB15-024a
Service Bulletin/Repair Instructions
2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB17-042c
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB13-008a
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-019
Service Bulletin/Repair Instructions
FRONT PASSENGER SEAT VIBRATION AT HIGHWAY SPEEDS WHILE UNOCCUPIED IF YOU CONFIRM The front passenger seat back vibrates at highway speeds while unoccupied. AND There are no other shake or vibration concerns with the vehicle. ACTION Replace the front passenger seat back frame with the new one listed in PARTS INFORMATION on the last page of this bulletin.
ITB12-011n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-042b
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB12-011m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-042
Service Bulletin/Repair Instructions
2013 M AND 2014-2017 Q70; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH® HANDS-FREE PHONE FEATURE IF YOU CONFIRM While using the Bluetooth® Hands-Free Phone Feature: - The call recipient (the person receiving the phone call) hears a whistle noise through their phone?s speaker during the call. - The whistle noise is not heard by the call sender (Infiniti customer) during the call. - The whistle noise increases when the engine RPM of the call sender?s vehicle is raised. ACTION Repair the related electrical harness wiring at the Telematics Control Unit (TCU).
ITB18-039
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
IPSB18-218 Retai
Service Bulletin/Repair Instructions
DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
ITB12-011l
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
Revision 1-IEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin The announcement from March 21, 2017 has been revised to include: o Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps o Client expense may be applicable if the vehicle is out of warranty
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
ITB13-044f
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.
ITB17-015a
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended: The Applied Vehicles section has been amended. No other changes have been made. Please discard previous versions of this bulletin.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB13-052b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB11-005d
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB03-051L
Service Bulletin/Repair Instructions
HEADLAMP FOGGING This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
IPSB15-286a
Service Bulletin/Repair Instructions
DBS Enhancement ? Checking Inventory for Open Campaigns UPDATE February 26, 2018 Please discard earlier versions of this bulletin The announcement from December 21, 2015 has been revised to include: 1. New functionality for identifying stop sales and parts restrictions for vehicles in dealer inventory 2. RDR warning messages when vehicles affected by a stop sale are submitted for retail delivery
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
ITB12-011k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
ITB18-003
Service Bulletin/Repair Instructions
REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
ITB12-011j
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.
ITB17-057
Service Bulletin/Repair Instructions
2011 - 2013 M AND M HYBRID, 2014-2015 Q70 AND Q70 HYBRID; POOR HEATER PERFORMANCE FROM THE PASSENGER SIDE IF YOU CONFIRM With the engine running at full operating temperature and the HVAC set to VENT (face) and 90°F on both sides, the VENT air temperature on the passenger side is more than 10°F colder than the VENT air temperature on the driver side, AND THEN When the HVAC control is adjusted to 60°F on both sides, there is a noticeable change from warm air to cool (A/C) air discharged from VENT on both sides. This confirms proper MIX door operation, NOTE: If the MIX door operation is abnormal, this bulletin does not apply. Refer to ASIST for further diagnostic information. AND No HVAC DTCs are stored. ACTION 1. Drain the engine coolant. 2. Modify the thermostat. 3. Flush the cooling system 3 times with Long Life Coolant. 4. Replace the heater core. 5. Replace the thermostat with gasket.
ITB09-039e
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-009a
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g
Service Bulletin/Repair Instructions
BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
ITB12-011i
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with factory Navigation system. This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.
ITB12-011h
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with factory Navigation system. This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.
ITB11-005c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-042a
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.
ITB17-015
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
ITB17-018
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
ITB17-007
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT This bulletin applies to vehcile equipped with navigation systems only. SERVICE INFORMATION On February 26, 2016 Infiniti announced that it was sending a reminder notification to clients affected by AT&T?s planned discontinuation of the 2G cellular network. In June 2016, Infiniti communicated instructions to retailers to update new vehicles in their inventory with 3G compatible telematics control units. At this time, Infiniti is beginning the process of making 3G compatible hardware available to owners of affected vehicles as identified above. This upgrade may require an owner to make a co-payment in order to receive the 3G hardware update. Please refer to the Claims Information below to determine if an owner co-pay is required. This client satisfaction initiative includes both the hardware upgrade and a complimentary one-year subscription to Infiniti Connection Plus telematics service; this does not apply to PC454 (see page 2 for details). You MUST use Service Comm to confirm bulletin Applicability. NOTE: - Vehicle eligibility will be viewed on the second page of Service Comm. This activity is not displayed on the main page of Service Comm because it is optional for customers to participate. - Vehicles without Navigation are ineligible as they are not equipped with TCUs. Retailer?s Responsibility It is the retailer?s responsibility to check SERVICE COMM using the appropriate Service Comm I.D. for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB13-052a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB16-047
Service Bulletin/Repair Instructions
INFINITI; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
ITB12-011g
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB12-011F
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION VEHICLES EQUIPPED WITH FACTORY NAVIGATION SYSTEM THIS BULLETIN HAS BEEN AMENDED. MODIFICATIONS HAVE BEEN MADE TO INCLUDE QX30. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
PC454
Service Bulletin/Repair Instructions
ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS SHOULD NOT SELL OR TRADE ANY AFFECTED VEHICLES IN RETAILER INVENTORY SUBJECT TO THIS SERVICE ACTION UNTIL THE 3G-COMPATIBLE TELEMATICS CONTROL UNIT HAS BEEN INSTALLED.
REVISION1-PC454
Service Bulletin/Repair Instructions
THIS ANNOUNCEMENT HAS BEEN REVISED TO CLARIFY THIS ACTIVITY IS NOT AN OFFICIAL STOP SALE. RETAILERS MAY SELL VEHICLES THAT HAVE NOT BEEN UPGRADED. PLEASE REFER TO ADDITIONAL Q&A SUPPLIED IN THIS DOCUMENT. PLEASE DISCARD EARLIER VERSIONS OF THIS BULLETIN. ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS ARE REQUESTED TO INSTALL A 3G-COMPATIBLE TELEMATICS CONTROL UNIT IN VEHICLES AFFECTED BY THIS SERVICE ACTION PRIOR TO RETAIL TO ENSURE CLIENT SATISFACTION.
ITB15021A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
ITB14044
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The rear brakes squeak when braking while the brakes are at normal operating temperature AND the applied vehicle is equipped with single piston rear brake calipers. ACTION: Replace the hardware on both rear brake calipers with the kit listed in PARTS INFORMATION in this bulletin. NOTE: Machining of the rotors is not necessary. Refer to the Electronic Service Manual (ESM), section BR-Brake System, for removal and installation. See this bulletin for further detail.
ITB14014
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.