Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008D
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008C
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008B
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-037E
Service Bulletin/Repair Instructions
RADIO PRESETS / CLIMATE CONTROL SETTINGS / NAVIGATION SETTINGS CHANGE WITH INTELLIGENT KEY MEMORY This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-015B
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB12-041D
Service Bulletin/Repair Instructions
SIRIUSXM SATELLITE RADIO / WEATHER / TRAFFIC / TRAVEL LINK ACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB10-017E
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT REQUIRES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-003F
Service Bulletin/Repair Instructions
NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-043a
Service Bulletin/Repair Instructions
2012 QX56; DOOR REQUEST SWITCH INOPERABLE AND NO START AT PDI This bulletin is no longer active. Please discard previous versions of ITB12-043.
ITB15-024a
Service Bulletin/Repair Instructions
2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB17-042c
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
DOR-M3J3F-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
DOR-M9J4S-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
ITB11-066f
Service Bulletin/Repair Instructions
PREMIUM NAVI/AUDIO VISUAL CONTROL UNIT DIAGNOSIS AND ORDERING This bulletin is no longer applicable. Discard previous versions of ITB11-066.
ITB19-023a
Service Bulletin/Repair Instructions
TAKATA DRIVERS AIR BAG MODULE REPLACEMENT COLLECTION INITIATIVE This bulletin has been superseded by ITB20-015. Please discard previous versions of this bulletin.
ITB13-008a
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
White Paint Dela
Service Bulletin/Repair Instructions
White Paint Delamination Warranty Extension On October 17, 2019, INFINITI distributed a retailer announcement notifying retailers of a proposed class action settlement (Nelson v. Nissan North America, Inc., Case No. 3:17-cv-01114 (M.D. Tenn.)), concerning paint peeling on INFINITI QX56 vehicles. The announcement provided a copy of notices sent to affected owners. A court hearing occurred on December 19, 2019 and the proposed settlement was approved by the presiding court for owners of pearl white INFINITI QX56 produced between November 20, 2009 and December 12, 2012. Owners of eligible vehicles will receive a notification of the settlement from the third party settlement administrator indicating their eligibility for the following: ï· - Warranty extension of 48 months and unlimited miles to their current 48 month/60,000 mile new vehicle limited warranty for a total of 96 months/unlimited mile warranty coverage for the pearl white paint for delamination. ï· - The paint warranty extension will allow for a one-time full vehicle repaint (subject to a client copayment). ï· - Eligible owners can also obtain coverage for rental car ($600 max) arising from the repaint. ï· - Eligibility for INFINITI's Vehicle Purchase Program (A-Plan) until April 30, 2020. Settlement details for this warranty extension can be found at the following website: www.vehiclepaintsettlement.com
ITB19-024
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on the next page. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
PC712 QX56 Healt
Service Bulletin/Repair Instructions
Driver Airbag Module Field Quality Parts Collection Initiative ***** Collection Initiative Summary ***** INFINITI is conducting a special parts collection activity on certain specific 2011-2012 QX56 (Z62) vehicles to replace the driver side airbag module free of charge. These vehicles are not subject to a recall. Instead, INFINITI is collecting a limited number of modules for engineering study. INFINITI will be notifying owners and asking them to participate in this important parts collection activity. As an incentive for participation, INFINITI is offering a complimentary oil and filter change for participating clients. NOTE: Clients should be informed that this parts collection activity is time-limited. Once a sufficient number of in-use modules has been collected, this activity will end. ***** What Retailers Should Do**** 1. Verify if vehicles are eligible for this parts collection activity using Service Comm or DBS National Service History â Open Campaign I.D. PC712. 2. Retailers should use ITB19-023 to service any QX56 vehicles subject to this activity. 3. The service department should submit the applicable warranty claim for the action(s) performed so the campaign can be closed on Service Comm and release the vehicle.
REVISION 1 - PC7
Service Bulletin/Repair Instructions
Driver Airbag Module Field Quality Parts Collection Initiative UPDATE September 6, 2019 Please discard earlier versions of this bulletin The announcement from earlier this morning (September 6, 2019) has been revised to include: o The part number listed in the Parts section of âRelease Scheduleâ below has been revised to K8510-1LC0B
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-042b
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-026b
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
Revision 1-IEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
IPSB18-218 Retai
Service Bulletin/Repair Instructions
DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
ITB17-026a
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL IF CUSTOMER REPORTS: Customer routinely experiences difficulty fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.
ITB13-044f
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.
ITB10-058b
Service Bulletin/Repair Instructions
2004-2018 QX56 AND QX80; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-015a
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended: The Applied Vehicles section has been amended. No other changes have been made. Please discard previous versions of this bulletin.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB13-052b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB11-005d
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB03-051L
Service Bulletin/Repair Instructions
HEADLAMP FOGGING This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
P6305 2011-13 QX
Service Bulletin/Repair Instructions
Timing Chain Voluntary Service Campaign - Final Expiration Notice ***** Campaign ***** INFINITI launched this Voluntary Service Campaign on May 6, 2016 on certain 2011-13 INFINITI QX56 and INFINITI M56 vehicles to offer clients the opportunity to replace the timing chain, chain guides, and crank sprocket at no charge to the client for parts and labor. INFINITI has made multiple attempts to notify clients concerning this service campaign and is now informing them that the campaign will end February 28, 2018. INFINITI wants to inform retailers to open repair orders on or before February 27, 2018 in order to have timing chain replacement covered by this service campaign. Vehicles presented for repair after this date will not be covered by this service campaign and any repair will be performed at client expense if the vehicle?s warranty has expired. ***** What Retailers Should Do ***** 1. Service Comm will deactivate P6305 on any unrepaired VINs on February 28, 2018. - Repair orders must be opened on or before February 27, 2018 - Claims submitted for repair orders opened after this date will be rejected. 2. Retailers should plan their parts inventory needs to align with the end of this campaign. 3. Retailers should submit any open claims for the timing chain replacement under this campaign as soon as possible. INFINITI would like to have all claims submitted by March 14, 2018.
ITB16-015b
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2011 ? 2013 QX56 AND M56; TIMING CHAIN Service Campaign ID # P6305 is No Longer Active. -Infiniti Service Campaign Bulletin ITB16-015 for Service Campaign P6305 was originally issued on May 5, 2016. -Service Campaign ID # P6305 is no longer active. -Repair orders opened after February 27, 2018 are no longer eligible for reimbursement under Campaign ID #P6305. -Please discard previous versions of ITB16-015.
ITB18-003
Service Bulletin/Repair Instructions
REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
P6305 2011-13
Service Bulletin/Repair Instructions
Timing Chain Voluntary Service Campaign - Expiration Notice ***** Campaign ***** INFINITI launched this Voluntary Service Campaign on May 6, 2016 on certain 2011-13 INFINITI QX56 and INFINITI M56 vehicles to offer clients the opportunity to replace the timing chain, chain guides, and crank sprocket at no charge to the client for parts and labor. INFINITI has made multiple attempts to notify clients concerning this service campaign and is now informing them that the campaign will end February 28, 2018. INFINITI wants to inform retailers to open repair orders on or before February 27, 2018 in order to have timing chain replacement covered by this service campaign. Vehicles presented for repair after this date will not be covered by this service campaign and any repair will be performed at client expense if the vehicle?s warranty has expired. ***** What Retailers Should Do ***** 1. Service Comm will deactivate P6305 on any unrepaired VINs on February 28, 2018. - Repair orders must be opened on or before February 27, 2018 - Claims submitted for repair orders opened after this date will be rejected. 2. Retailers should plan their parts inventory needs to align with the end of this campaign. 3. Retailers should submit any open claims for the timing chain replacement under this campaign as soon as possible. INFINITI would like to have all claims submitted by March 14, 2018.
ITB09-039e
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-009a
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g
Service Bulletin/Repair Instructions
BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
P6305
Service Bulletin/Repair Instructions
Timing Chain Voluntary Service Campaign - Expiration Notice ***** Campaign Summary ***** INFINITI launched this Voluntary Service Campaign on May 6, 2016 on certain 2011-13 INFINITI QX56 and INFINITI M56 vehicles to offer clients the opportunity to replace the timing chain, chain guides, and crank sprocket at no charge to the client for parts and labor. INFINITI has made multiple attempts to notify clients concerning this service campaign and is now informing them that the campaign will end February 28, 2018. INFINITI wants to inform retailers to open repair orders on or before February 27, 2018 in order to have timing chain replacement covered by this service campaign. Vehicles presented for repair after this date will not be covered by this service campaign and any repair will be performed at client expense if the vehicle?s warranty has expired. ***** What Retailers Should Do ***** 1. Service Comm will deactivate P6305 on any unrepaired VINs on February 28, 2018. - Repair orders must be opened on or before February 27, 2018 - Claims submitted for repair orders opened after this date will be rejected. 2. Retailers should plan their parts inventory needs to align with the end of this campaign. 3. Retailers should submit any open claims for the timing chain replacement under this campaign as soon as possible. INFINITI would like to have all claims submitted by March 14, 2018.
ITB11-005c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-042a
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.
ITB17-015
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
ITB17-026
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
ITB17-018
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
ITB13-052a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB12-054B
Service Bulletin/Repair Instructions
THIS BULLETIN HAS BEEN AMENDED. THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
ITB16-015A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2011 2013 QX56 AND M56; TIMING CHAIN THIS BULLETIN HAS BEEN AMENDED. THE CLAIMS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. INTRODUCTION INFINITI IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN 2011-2013 QX56 AND 2011-2013 M56 VEHICLES TO REPLACE THE TIMING CHAIN. THIS SERVICE WILL BE PERFORMED AT NO COST TO THE CUSTOMER FOR PARTS OR LABOR.
REVISION1-P6305
Service Bulletin/Repair Instructions
TIMING CHAIN VOLUNTARY SERVICE CAMPAIGN THE ANNOUNCEMENT FROM MAY 6, 2016 HAS BEEN REVISED TO REFLECT INCREASED FLAT RATE TIMES AND INCLUDES ADDITIONAL QUESTIONS & ANSWERS IN THE FREQUENTLY ASKED QUESTIONS (FAQ) SECTION SUCH AS: - AN EXPLANATION REGARDING THE FLAT RATE TIME CHANGE - WHAT TO DO IF THE RETAILER IDENTIFIES ADDITIONAL PARTS ARE FOUND THAT ARE EXCESSIVELY WORN OR DAMAGED DUE TO THE TIMING CHAIN - WHAT TO DO IF THE CLIENT HAS ALREADY HAD THEIR TIMING CHAIN REPLACED ***** CAMPAIGN SUMMARY ***** INFINITI IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN MY 2011-13 QX56 AND M56 VEHICLES TO REPLACE THE ENGINE TIMING CHAIN, GUIDES, AND CRANKSHAFT SPROCKET. IN SOME OF THE AFFECTED VEHICLES, THE TIMING CHAIN MAY DETERIORATE OVER TIME AND DISTORT. IF THIS OCCURS, CLIENTS WILL HEAR ABNORMAL NOISES FROM THE ENGINE, WHICH MAY SOUND LIKE A RATTLE OR TICKING. IF THE ABNORMAL ENGINE NOISE CONTINUES, OVER TIME THE ENGINE COULD BE DAMAGED. INFINITI IS PERFORMING THIS REPAIR AT NO CHARGE TO AFFECTED CLIENTS FOR PARTS OR LABOR TO HELP ENSURE CONTINUED SATISFACTION WITH THEIR INFINITI VEHICLE. INFINITI IS COMMITTED TO A HIGH LEVEL OF PRODUCT SAFETY, SERVICE AND SATISFACTION FOR INFINITI OWNERS AND IS WORKING WITH ITS RETAILERS TO PROMPTLY ADDRESS THIS ISSUE. ***** WHAT RETAILERS SHOULD DO ***** TO ENSURE CLIENT SATISFACTION, RETAILERS ARE ASKED TO PERFORM THE FOLLOWING REPAIR PROCEDURE PRIOR TO SALE OF PRE-OWNED AND NEW (IF APPLICABLE) INVENTORY.
ITB11021B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.
P6305OL
Service Bulletin/Repair Instructions
Infiniti is conducting a Voluntary Service Campaign on certain 2011-2013 QX56 and 2011-2013 M56 vehicles to replace the ?Timing Chain?.
ITB09041A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
ITB09063B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
ITB15021A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
ITB12026F
Service Bulletin/Repair Instructions
IF YOU CONFIRM: An APPLIED VEHICLE has the MIL ON with DTC P0106 (Manifold Absolute Pressure [MAP] circuit range/performance) stored in the ECM. ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM with CONSULT-III plus ONLY. See this bulletin for further detail.
ITB03051J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
ITB09039C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Infiniti dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
ITB16005
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
ITB13007A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.
ITB09015G
Service Bulletin/Repair Instructions
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
ITB11042D
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
ITB13039A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
ITB10017D
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
ITB14028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
ITB10037D
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
ITB15025
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
ITB15024
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
ITB15020
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
ITB10062E
Service Bulletin/Repair Instructions
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
ITB99043G
Service Bulletin/Repair Instructions
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
ITB00031D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
ITB13002A
Service Bulletin/Repair Instructions
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
ITB11003E
Service Bulletin/Repair Instructions
SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
ITB12041C
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather or Travel Link OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
ITB12025A
Service Bulletin/Repair Instructions
IF YOU CONFIRM The Engine Cooling Fan is louder than normal. and There is a noticeable lack of power when accelerating in traffic, particularly in HOT weather. ACTIONS 1. Reprogram the ECM, if necessary. 2. Perform Engine Fan Coupler function inspection. - With engine temperature between 80-95°C (176-203°F), confirm that Cooling Fan speed responds to the commands of the ECM with the procedure starting on page 10. 3. Replace the fan coupler, if necessary. See this bulletin for further detail.
ITB14056
Service Bulletin/Repair Instructions
SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
ITB14054
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the auto back door will not operate automatically (operates only in manual mode), first note some conditions that may cause this: * Is DTC B2420 set as "current" in the back door control unit? If the auto back door "CLOSE SW" (close switch) state does not change from ON to OFF after 3 attempts to close the auto back door, B2420 will be set and the auto feature will be disabled. Please see this bulletin for further details.
ITB14055
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
ITB10058A
Service Bulletin/Repair Instructions
IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION: Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). See this bulletin for further detail.
ITB13053A
Service Bulletin/Repair Instructions
IF YOU CONFIRM MIL "ON" with DTC P0420 and/or P0430 (Three Way Catalyst Function), ACTION: 1. Reprogram the ECM (if needed). 2. Replace three way catalyst and A/F sensor. See this bulletin for further detail.
ITB10029A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
ITB14020
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
ITB11048B
Service Bulletin/Repair Instructions
SERVICE INFORMATION The rear seat headphones have an "A" channel (Ach) and a "B" channel (Bch). The channel switch is on the headphone ear pad case. If a person is sitting on the left side (driver side) of the vehicle and their headphones are set to Bch, the headphones may have static or intermittently operate (cut in and out). OR If a person is sitting on the right side (passenger side) of the vehicle and their headphones are set to Ach, the headphones may have static or intermittently operate (cut in and out). NOTE: If the headphones are set to the "correct channel" for the seating position, but still have static or do not operate, check the condition of the "AAA" headphone batteries located under the left side headphone cover. Do not replace the headphones for the above issues. See this bulletin for further detail.
ITB08024C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
ITB14002
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
ITB13052
Service Bulletin/Repair Instructions
SERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-Key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
ITB-13-044
Service Bulletin/Repair Instructions
INFINITI: THE INSTRUMENT CLUSTER HAS A WARNING INDICATOR, THAT ILLUMINATES, OF A LOOSE FUEL FILL CAP. MODEL YEARS 2012 AND UP. NO MODELS LISTED. *PE
ITB12063C
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer reports that people on the other end of a phone call cannot hear them. Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Reprogram (reconfigure) the Multi AV. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.
ITB13042
Service Bulletin/Repair Instructions
IF YOU CONFIRM: Both seat heaters of the second row seats do not work. AND Fuse # 14 is found open (or "blown"). NOTE: This issue applies to both captain and bench type second row heated seating. ACTION: 1. Repair the right side second row seat: a. Clean off welding spatter on the seat hinge (the cause of harness damage), and then apply protective covering on the seat hinge. b. Repair the damaged seat harness wiring or replace the seat harness as necessary. - For repairs, refer to SERVICE PROCEDURE starting on page 3. See this bulletin for further detail.
ITB-13-039
Service Bulletin/Repair Instructions
INFINITI: SERVICE BULLETIN CONCERNING LOW TIRE PRESSURE WARNING SYSTEM INFORMATION. *JS
ITB-13-009
Service Bulletin/Repair Instructions
INFINITI: WHINE NOISE FROM ENGINE AREA. IF THE NOISE DOES NOT INCREASE WITH ENGINE SPEED, THE TIMING CHAIN SYSTEM MAY NOT BE THE CAUSE. *JS UPDATED 10/29/2013 *JS
ITB-92-069-D
Service Bulletin/Repair Instructions
INFINITI: DUE TO USE OF AFTERMARKET CHROMING OF ALLOY WHEELS, FOR SOME VEHICLES, THE STANDARDS ARE NO LONGER ARE MET AND ARE SERIOUSLY DAMAGED AND NOT GUARANTEE OR WARRANTY THE MODIFIED WHEELS OR PERFORMANCE. MODELS ALL. NO YEARS LISTED. *PE
ITB92069D
Service Bulletin/Repair Instructions
Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
ITB13006A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
ITB11066E
Service Bulletin/Repair Instructions
SERVICE INFORMATION Part order approval from TECH LINE is no longer required when replacing the Audio Visual (A/V) Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.
ITB00024F
Service Bulletin/Repair Instructions
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
ITB04038A
Service Bulletin/Repair Instructions
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
ITB98011F
Service Bulletin/Repair Instructions
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
ITB13016
Service Bulletin/Repair Instructions
IF YOU CONFIRM One or more of the following conditions: Front passenger air bag status light is ON (illuminated) with the front passenger seat empty. Front passenger air bag status light is ON (illuminated) with an adult sitting in the front passenger seat. Seat belt warning light is ON (illuminated) with the front passenger seat empty (driver seat belt is buckled). Supplemental air bag warning light is flashing but no Air Bag DTCs are stored. ACTION 1. Visually check the front passenger seat and seat rails for any structural damage. 2. Visually check the front passenger seat for any items in the seat pockets, or any items on, under, or hanging from the seat (front, back, and sides). 3. Replace the OCS control unit. 4. Perform Zero Point Rest and check for DTCs. See this bulletin for further detail.
ITB13-016
Service Bulletin/Repair Instructions
INFINITI: ON THE INSTRUMENT PANEL THE AIR BAG AND SEAT BELT WARNING LIGHTS GIVE OFF AN INCORRECT INDICATION. *KB
ITB-13-13
Service Bulletin/Repair Instructions
INFINTI: CRUISE CONTROL WILL NOT SET AND DTC P0605 IS STORED. IF A MALFUNCTION IN THE ASCD SYSTEM IS DETECTED, THE CRUISE INDICATOR MAY STAY ON AND THE SET INDICATOR MAY FLASH. *JS
ITB13013
Service Bulletin/Repair Instructions
SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
ITB-13-12
Service Bulletin/Repair Instructions
INFINITI: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE DOOR HANDLE OUTSIDE DOOR HANDLE DOES NOT RESPOND. LOCK/UNLOCK REQUEST BUTTON LOCATED ON OUTSIDE DOOR HANDLES OF VEHICLES CAN BE DISABLED (OR ENABLED) THROUGH EITHER THE "COMFORT & CONV" SETTINGS OF THE AUDIO/VISUAL/NAVIGATION SYSTEM OR THROUGH THE "COMBINATION METER SETTINGS" DEPENDING ON THE VEHICLE MODEL, YEAR, AND TRIM LEVEL. *JS
ITB13012
Service Bulletin/Repair Instructions
SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
ITB13008
Service Bulletin/Repair Instructions
IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. >Please see Service procedure for 2007-2011 Versa torque specifications on page 5. See this bulletin for further detail.
ITB99001A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
ITB12016B
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The following incidents with The Auto Drive Position System: * Door mirrors do not go back to the original preset memory position after the vehicle is shifted into reverse, and then shifted back into drive. * Return position of mirrors drifts farther and farther from original memory preset as mirror is cycled from the drive to reverse positions (cumulative). * With vehicle in park and engine turned off, the Seat and Steering Wheel do not move when exiting vehicle. ACTION: Replace Left Power Seat Control Unit with new part listed in PARTS INFORMATION in this bulletin. See this bulletin for further details.
ITB13003
Service Bulletin/Repair Instructions
SERVICE INFORMATION When the fluid of an applied vehicle's transfer assembly is being "topped off" or refilled for any reason, use only Genuine NISSAN Transfer Fluid (P/N 999MP-TF0870P). Using transfer fluid other than Genuine NISSAN Transfer Fluid or its equivalent will damage the transfer, which is not covered by the INFINITI new vehicle limited warranty. Order this item through the Infiniti Maintenance Advantage program: Phone: 877-INF-IMA1 (877-463-4621), order online via the link on www.NNAnet.com>Workspace tab>Parts and Service Section>Click on "Maintenance Advantage", or order direct at www.nissantire.com. See this bulletin for further detail.
ITB11014B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
ITB10066E
Service Bulletin/Repair Instructions
IF YOU CONFIRM One or more of the following is occurring on an Applied Vehicle: - Audio streaming via Bluetooth is "choppy" or "clipped." - Calculating Route" takes an extended period of time (2-5 minutes) to complete. - Could not find a route" displays when attempting to calculate a route. - Voice Recognition sequence takes too many steps. - Voice Recognition has difficulty recognizing voicetags. - The Navigation system reboots. - XM NavTraffic is slow to report. - "Handset Phonebook" access is slow. - Caller ID is not available when a hands-free call via Bluetooth is in progress and another call comes in. ACTION 1. Perform steps 1-7 of Check Navigation Program Version in the Service Procedure to verify whether or not this bulletin applies. 2. If this bulletin applies, Follow the Service Procedure to load the Reprogramming Software DVD referenced in the Parts Information section. See this bulletin for further detail.
ITB11054A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: Any of the following DTCs are stored in the ECM: - P0031 / P0051, P0032 / P0052, P0130 / P0150, P0133 / P0153, P2A00 / P2A03, P1148 / P1168 OR Any of the following DTCs are stored in the ECM as a result of one of the A/F sensors: - P0300 - P0308, P0171 / P0174, P0172 / P0175 ACTION: 1. Replace the A/F sensor that relates to the stored DTC(s) (B1 and/or B2). 2. Refer to step 7 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 3. If it applies, reprogram the ECM. See this bulletin for further detail.
ITB-12-077
Service Bulletin/Repair Instructions
INFINITI: STORED IN ECM IS CODE DTC P008B (LOW FUEL PRESSURE TOO HIGH) WITH MIL ON, AND NEEDS REPROGRAMMING. MODEL 2012 QX56. *PE
ITB11005B
Service Bulletin/Repair Instructions
SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed: - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.
ITB12077
Service Bulletin/Repair Instructions
IF YOU CONFIRM: An APPLIED VEHICLE has the MIL 'ON' with DTC P008B (Low Fuel Pressure Too High) stored in the ECM. ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
P2563
Service Bulletin/Repair Instructions
Infiniti is conducting a retailer service action to reprogram the ECM on certain specific 2012 and 2013 Infiniti QX56 vehicles to prevent the fuel pump pressure from becoming higher than design specifications and illuminating the MIL light.
ITB12071
Service Bulletin/Repair Instructions
SERVICE INFORMATION Part of the procedure to remove the glass mirror in either door mirror of an applied vehicle has been changed. Until the related Electronic Service Manuals (ESM) are amended, use the information in this bulletin. - Other than noted, all other procedural steps in the ESM remain the same. See this bulletin for further detail.
ITB12070
Service Bulletin/Repair Instructions
SERVICE INFORMATION The "Reverse Tilt-Down" feature will move the glass on the outside mirrors downward when the gear selector is placed in the Reverse (R) position. As the mirror glass moves downward, it may reach the end of its travel. If the mirror glass reaches the end of its travel it will make a clicking noise. The clicking noise may occur once or multiple times. IMPORTANT: - The clicking noise described above is a normal function of the mirror glass movement. - Do not replace the door mirror assembly in an attempt to repair this normal function.
ITB12068
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally, after a rain or a car wash, customers may notice water drops in the overhanging part of the rear combination lamp lens. - This is a normal condition. - The water drops should disappear over time when the lamp is in a dry environment. - Refer to the images on page 2 of this bulletin for examples of a normal water drop condition. - Do not replace any parts for this condition. See this bulletin for further detail.
ITB-10-056-A
Service Bulletin/Repair Instructions
INFINITI: INFORMATION PROVIDED REGARDING ACCURATE DIAGNOSIS OF ABS/VDC WHEEL SPEED SENSORS ON CERTAIN VEHICLES. MODELS 2007-2013 INFINITI. *PE
ITB-09-011-A
Service Bulletin/Repair Instructions
INFINITI: WHEN INSECTS, DIRT, FINGER PRINTS, OIL FILM, MOISTURE OR EXHAUST GAS IS NEAR OR AROUND RAIN SENSOR, THIS CAUSES THE RAIN SENSOR, WHEN WIPER LEVER IS PUSHED DOWN, TO EITHER MAKE A SINGLE STROKE OR OPERATE UNEXPECTEDLY. NO MODELS OR MODEL YEARS LISTED. *PE
ITB-11-049-B
Service Bulletin/Repair Instructions
INFINITI: REPROGRAMMING ELECTRONIC CONTROL UNIT (ECU) ON ALL QUALIFYING VEHICLES. NO MODELS LISTED. MODEL YEARS 1998-2013. *PE
ITB12-025
Service Bulletin/Repair Instructions
INFINITI: THE ENGINE FAN IS NOISY AND THERE IS NOTICEABLE LACK OF POWER WHEN ACCELERATING IN TRAFFIC, PARTICULARLY IN HOT WEATHER. *JS
ITB12-018
Service Bulletin/Repair Instructions
INFINITI: THE ELECTRONIC CONTROL MODULE (ECM) NEEDS TO BE REPLACED ON A 2004 MY AND LATER VEHICLE. *JS
ITB-12-005
Service Bulletin/Repair Instructions
INFINITI: VEHICLES USING INTELLIGENT KEY SYSTEM AND/OR DOOR REQUEST SWITCH CAN NOT LOCK OR UNLOCK VEHICLE DOORS. *PE
ITB-11-067
Service Bulletin/Repair Instructions
INFINITI: BULLETIN PROVIDES SERVICE PROCEDURES FOR REPROGRAMMING THE ELECTRONIC CONTROL MODULE (ECM). MODELS QX56. *PE