Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB23-023A
Service Bulletin/Repair Instructions
AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of ITB23-010.
ITB23-010D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of ITB23-010.
ITB12-011Q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-001E
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-023B
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-055D
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-011G
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008D
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the client is experiencing a software related concern, refer to ITB21-011 to verify if the client concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-041
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.
ITB22-040
Service Bulletin/Repair Instructions
3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. INFINITI Connection with InTouch⢠Services are no longer available on the APPLIED VEHICLES listed above.
ITB12-072I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008C
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 2 QX60
Service Bulletin/Repair Instructions
CVT Warranty Extension UPDATE August 30, 2022 Please discard earlier versions of this bulletin. The announcement from June 2, 2022 has been revised to include: ⢠The voucher program ID numbers provided in the FAQ section of this retailer announcement have been changed. The new voucher program ID numbers are: ï INFINITI program ID: 22I2299CVT ï Nissan program ID: 22N2299CVT
ITB17-001D
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-023A
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
QX60 CVT - WE -
Service Bulletin/Repair Instructions
CAMPAIGN BULLETIN CVT Warranty Extension In an effort to assure client satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address client concerns including those expressed by clients in the class actions, INFINITI will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicle listed in this announcement. The warranty is being extended from its original duration of 72 months/70,000 miles to 96 months/94,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of INFINITIâs New Vehicle Limited Warranty continue to apply. ***** What Retailers Should Do ***** 1. If an owner contacts a retailer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the client of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the client concern and identify the correct repair to resolve the client concerns. NOTE: Retailers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealerâs Claims Administration/Authorization Limits (DCAL).
ITB12-072H
Service Bulletin/Repair Instructions
INFINITI AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-015
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
2015-2018 QX60 C
Service Bulletin/Repair Instructions
CVT Variable Transmission (CVT) Class Action Owner Notification On March 23, 2022, the Court presiding over a class action lawsuit gave final approval to a proposed settlement under which the CVT warranty will be extended for the following vehicle: 2015-2018 QX60 *Not including QX60 Hybrid model vehicles The approved settlement and the warranty extension are expected to become effective by June 1, 2022. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, for the time being there is no warranty extension, and you should proceed with CVT-related claims as outlined below in bullet point three (3) under What Retailers Should Do. ***** What Retailers Should Do ***** 1. No action is necessary at this time. INFINITI will provide additional instructions prior to the effective date of the extended warranty, which is expected to be June 1, 2022. 2. If a client contacts the retailer with a CVT concern in an owned or leased vehicle, retailers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the client concern and identify the correct repair to resolve the client concerns. NOTE: Retailers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992 Option 2) for any vehicles requiring CVT assemblies to be replaced. Valve bodies and CVT belt and pulley kits do not require pre-authorization. 3. If the vehicle is no longer covered by a powertrain or parts warranty, provide owners a repair estimate for test drive, diagnosis, and repair after consulting the Goodwill rental guidelines available in the Assurance Product Resources Manual (APRM) for detailed information regarding application of rental reimbursement.
ITB22-012
Service Bulletin/Repair Instructions
HEADREST DVD DISPLAY ISSUES IF YOU CONFIRM One or both of the headrest DVD displays are inoperative. OR One or both of the headrest DVD displays are gray (fuzzy) and then change to a solid blue color before displaying the image from the DVD. ACTION Install 2 service jumper harnesses, which connect from each headrest DVD display to the video distributor.
ITB12-072G
Service Bulletin/Repair Instructions
INFINITI AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-001C
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-023
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.
PC835 - R1606 Ca
Service Bulletin/Repair Instructions
R1606 Occupant Classification System (OCS) Campaign Quality Review ***** Retailer Announcement ***** INFINITI is committed to the safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1606). If the VIN displays QA campaign ID PC835, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIâs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC835. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. ⢠Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.
ITB13-008B
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-026D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-012D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-055B
Service Bulletin/Repair Instructions
INFINITI; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB17-001B
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-007
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-028A
Service Bulletin/Repair Instructions
2016 QX60 LANE CAMERA AIMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-006B
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2017 QX60; VDC WARNING LAMP ON WITH DTC C1116 STORED This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-021B
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-023A
Service Bulletin/Repair Instructions
2016 INFINITI; REGISTRATION OF NEW I-KEYS WHEN ORIGINALS ARE MISSING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-026C
Service Bulletin/Repair Instructions
INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-003A
Service Bulletin/Repair Instructions
INFINITI; REPLACING LOST INTELLIGENT KEYS FOR APPLICABLE 2016 MODEL YEAR VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-012C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052C
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB17-005A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
ITB17-041A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB12-011P
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-034B
Service Bulletin/Repair Instructions
CVT OIL LEAK DIAGNOSIS USING FLUORESCENT DYE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-010e
Service Bulletin/Repair Instructions
INFINITI; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of ITB15-010. Refer to the ESM for the fluid cooler cleaning procedure.
ITB19-013b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-012i
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 â 2018 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB12-076d
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
EXPIRATION NOTIF
Service Bulletin/Repair Instructions
Expiration Notification - 2G Telematics Hardware Replacement Campaign Summary In 2016, INFINITI launched a Client Satisfaction Initiative (CSI) that provided clients with an opportunity to update the Telematics Control Unit (TCU) in vehicles equipped with a TCU designed to connect to the 2G cellular network. AT&T stopped accepting enrollments on the 2G cellular network, and discontinued its 2G cellular network coverage on December 31, 2016. Once the 2G cellular network was discontinued, there was no access to the INFINITI Connection features without a TCU hardware upgrade. Because AT&T will shut down its 3G network on December 31, 2021, INFINITI is discontinuing this Client Satisfaction Initiative to upgrade from 2G to 3G compatible hardware effective immediately. 3G services will continue to be provided until December 31, 2021. Vehicles equipped with a TCU that connects to the 3G cellular network will have no access to the INFINITI Connection features, including Emergency Calling and Automatic Collision Notification after that time. What Retailers Should Do Service Comm will deactivate PC451, PC452 and PC454 on any VINs on December 22, 2020. No further retailer action is required.
ITB17-007a
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT Customer Satisfaction Initiative ID # PC451, PC452 and PC454 are no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC451, PC452 or PC454. ï· Please discard all previous versions of ITB17-007.
ITB16-031a
Service Bulletin/Repair Instructions
2016 QX60; AUTOMATIC BACK DOOR CALIBRATION PROCEDURE This bulletin is no longer active. Please discard previous versions of ITB16-031.
ITB19-013a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-072f
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2019 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042c
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-001a
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-026c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB20-004
Service Bulletin/Repair Instructions
2013 JX AND 2014-2019 QX60; CLIMATE CONTROLLED SEAT INOPERATIVE IF YOU CONFIRM The driver or passenger side climate controlled seat: ï· - Heating and cooling features do not operate And ï· - The harness connector or control unit of the climate controlled seat appears as shown in Figure 3 or Figure 5. ACTION Perform the following to the affected seat: A. Replace the climate controlled seat control unit. B. Drill a hole for the new harness clip. C. Replace the harness connector of the climate controlled seat control unit.
ITB13-008a
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-027a
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
P9329_P9344_P934
Service Bulletin/Repair Instructions
Engine Control Module (ECM) Reprogram California Voluntary Emission Service Campaign ***** Campaign Summary ***** INFINITI is conducting a Voluntary Emissions Service Campaign on approximately 49,497 specific INFINITI vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or âSmog Checkâ test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History â Open Campaign I.D. ï· P9329 â Affected Model Year 2015 ï· P9344 â Affected Model Year 2016 ï· P9346 â Affected Model Year 2017 ï· P9348 â Affected Model Year 2018 ï· P9350 â Affected Model Year 2019 2. Retailers are requested to repair any affected vehicles in retailer new or pre-owned inventory to ensure client satisfaction. ï· - New vehicles in retailer inventory can also be identified DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to IPSB 15-286 for additional information 3. Retailers should use ITB19-043 to correct any vehicles subject to this campaign.
ITB19-043
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Infiniti is conducting this voluntary emissions service campaign on certain specific model year Infiniti vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification numbers P9329, P9344, P9346, P9348, and P9350 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY Retailers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailerâs inventory.
ITB15-010d
Service Bulletin/Repair Instructions
INFINITI; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-012h
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 â 2018 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB16-035b
Service Bulletin/Repair Instructions
2015-2017 QX60; ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been superseded by ITB15-012. Please discard previous versions of this bulletin.
ITB12-011o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-027
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has one or more DTCs stored, shown in Table A on page 2, AND The ECM part number is shown in Table B, starting on page 3. ACTION 1. First perform the appropriate diagnostic procedure for the stored DTC to repair the vehicle according to the Electronic Service Manual (ESM). 2. Reprogram the ECM after performing the diagnosis and repair. ï· -The ECM reprogram in this Service Procedure is not a repair for the DTC, but instead updates the way the permanent DTC is stored and allowed to be erased. The DTC must be properly diagnosed and repaired before the reprogram is applied.
ITB19-025
Service Bulletin/Repair Instructions
QX60; TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch is now available as a separate service part. If the transmission range switch is being replaced for any reason, it must be adjusted after its replacement. ï· - Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
ITB19-024
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on the next page. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
ITB14-011d
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-014
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2020 QX60; REMOVAL OF HEADLIGHT ASSEMBLY LOCATING BRACKET SERVICE INFORMATION If replacement of a Front Combination Headlamp assembly (headlight assembly) is necessary, for the applied vehicles, the locating bracket (if present) on the new replacement headlight assembly must first be removed before installation. Inspect the new replacement headlight assembly and confirm if a locating bracket is attached, with a Torx screw, on top in the center (see Figure 1). Is a locating bracket present? - NO: This bulletin does not apply. Continue with the installation of the new replacement headlight assembly. - YES 1. Using a T10 Torx screwdriver, remove the locating bracket attached to the topcenter of the replacement headlight assembly (see Figure 1). 2. Discard the locating bracket and Torx screw. 3. Continue the installation of the replacement headlight assembly. NOTE: Refer to the Electronic Service Manual (ESM) for the procedure to remove or install a headlight assembly. CAUTION: Take care when installing the headlight assembly so that the painted surface of the fender is not damaged. - Black electrical tape can be used to protect the edge of the fender while installing the headlight assembly.
ITB14-053b
Service Bulletin/Repair Instructions
ABNORMAL NOISE FROM FRONT ENGINE MOUNT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-013
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
ITB19-011
Service Bulletin/Repair Instructions
DEAD PEDAL REPLACEMENT SERVICE INFORMATION If the dead pedal needs to be replaced for anyreason, it is no longer necessary to replace the front floor trim (carpet). The dead pedal is now available as a service part. NOTE: Do not replace the carpet if only the dead pedal is needed. ACTION Follow the SERVICE PROCEDURE on the next page to replace ONLY the dead pedal. NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.
ITB19-010
Service Bulletin/Repair Instructions
2016-2018 QX60; MIL ON WITH DTC P2097, P2099, P0171 AND/OR P0174 This bulletin applies only to vehicles equipped with the VQ35DE engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on the next page to confirm if Electronic Control Module (ECM) reprogramming is needed.
ITB19-008
Service Bulletin/Repair Instructions
EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB13-055c
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-026b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB18-006a
Service Bulletin/Repair Instructions
2013 JX35 AND 2014-2017 QX60; VDC WARNING LAMP ON WITH DTC C1116 STORED This bulletin has been amended. Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-006
Service Bulletin/Repair Instructions
INFINITI; MIL ON WITH DTC P219A AND/OR P219B STORED SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
ITB16-012b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-044g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB17-042b
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB12-011m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-026b
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
Revision 1-IEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
ITB18-039
Service Bulletin/Repair Instructions
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
ITB12-072e
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2017 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies to AWD (All-Wheel Drive) vehicles only. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-026a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-037
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB18-034
Service Bulletin/Repair Instructions
TRANSMISSION & ENGINE AUTOMATED DATA COLLECTION AND DIAGNOSTIC REPORTING SERVICE INFORMATION To support proper diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.
ITB15-026b
Service Bulletin/Repair Instructions
INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
Infiniti USA Ret
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Retailed Vehicle Open Campaign Report Lists Updated The lists for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.
Infiniti USA Tak
Service Bulletin/Repair Instructions
Infiniti USA Electronic Field Communication Subject: Takata Completion Objectives for Q3 INFINITI is continuing to ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.
IPSB18-218 Retai
Service Bulletin/Repair Instructions
DBS Enhancement: Retailed Vehicle Open Campaign Report INFINITI announced the availability of a new DBS enhancement tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.
ITB12-072d
Service Bulletin/Repair Instructions
2013 JX35, 2014-2019 QX60, 2014-2017 QX60 HYBRID; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB12-011l
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement UPDATE August 17, 2018 Please discard earlier versions of this bulletin. The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty
ITB17-026a
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL IF CUSTOMER REPORTS: Customer routinely experiences difficulty fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.
ITB13-035c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB13-044f
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.
ITB18-026
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each retailer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
ITB01-024e
Service Bulletin/Repair Instructions
NEW PAINT GUARD FILM REMOVAL INFORMATION This bulletin applies only to new, unsold vehicles with Paint Guard Film in Dealer Stock. This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB13-052b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB11-005d
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB03-051L
Service Bulletin/Repair Instructions
HEADLAMP FOGGING This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
IPSB17-130
Service Bulletin/Repair Instructions
DBS Enhancement: Custom VIN Campaign Report INFINITI is pleased to announce the availability of a new DBS enhancement to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)
ITB12-011k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
ITB18-006
Service Bulletin/Repair Instructions
2016-2017 QX60; VDC WARNING LAMP ON WITH DTC C1116 STORED This bulletin applies only to vehicles NOT equipped with Intelligent Cruise Control. IF YOU CONFIRM A current or past customer concern of the Vehicle Dynamic Control (VDC) warning light being ON with either a current or past DTC C1116 (STOP LAMP SW) stored. And Brake lamp switch operation has been confirmed as operating correctly. ACTION Install the harness jumper from the Parts Information using the Service Procedure starting on page 2.
ITB18-003
Service Bulletin/Repair Instructions
REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
ITB12-011j
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.
ITB09-039e
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-009a
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g
Service Bulletin/Repair Instructions
BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
ITB12-011i
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with factory Navigation system. This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.
ITB12-011h
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with factory Navigation system. This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.
ITB11-005c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-048
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2017 QX60; RADIATOR SHROUD AND COOLING FAN ASSEMBLY REPLACEMENT PROCEDURE SERVICE INFORMATION When replacing the radiator shroud and cooling fan assembly for any reason, the engine coolant, air cleaner case, and air duct does not need to be removed as part of the procedure. Use this SERVICE PROCEDURE (in place of the ESM) and the CLAIMS INFORMATION in this bulletin. The ESM will be updated at a later date. IMPORTANT: You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB17-016c
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2016 QX60 OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 15 and 17 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-042a
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-002b
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-016b
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2016 QX60 OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB17-046
Service Bulletin/Repair Instructions
DTC P0036 DIAGNOSTIC INFORMATION SERVICE INFORMATION The Electronic Service Manual (ESM) information for DTC P0036 may be inaccurate or incomplete for the Applied Vehicles. If an Applied Vehicle stores a DTC P0036, follow diagnostic procedures in the ESM for Bank 2 A/F Sensor Heater open or shorted.
ITB14-053a
Service Bulletin/Repair Instructions
THUNK SOUND ON FIRST FEW ACCELERATIONS OF THE DAY This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
ITB17-042
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to ITB13-044). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.
ITB16-021a
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
P7331
Service Bulletin/Repair Instructions
Disabling the 2G TCU Voluntary Service Campaign ***** Campaign Summary ***** Infiniti is conducting a Voluntary Service Campaign to disable (turn off) the 2G Telematics Control Unit (?2G TCU?). The subject QX56/QX80, JX35/QX60, M37/M56/Q70, and 2014-15 Q50 vehicles are equipped with Continental GEN1 TCU devices transmitting at 2/2.5G (GSM/GPRS/UMTS) frequencies and are designed to work with 2G cellular service. The 2G cellular service is no longer active in the United States. The subject 2G TCUs are no longer connected to telematics services and no longer perform any function in the affected vehicles. This campaign is being performed out of an abundance of caution to help safeguard against potential cybersecurity issues. - All eligible vehicles that enter the service department for any reason should have the subject 2G TCU deactivated. This campaign will be performed at no charge to the client for parts and labor. - Vehicles that have been upgraded to 3G TCUs are not subject to this campaign. - For clients interested in the 3G TCU upgrade as opposed to deactivation, please refer to ITB17-007 (PC451, PC452, or PC454)
ITB17-041
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN INFINITI; 2G TELEMATICS HARDWARE DEACTIVATION INTRODUCTION Infiniti is conducting a Voluntary Service Campaign (in the U.S. ONLY) on certain specific 2013-2016 Infiniti vehicles equipped with 2G Telematics Hardware to disable the 2G Telematics Control Unit (TCU). The 2G cellular service is no longer active in the United States and the subject TCUs are no longer connected to telematics services (Infiniti ConnectTM) and no longer perform any function in the affected vehicles. This campaign is being performed out of abundance of caution to help prevent potential cybersecurity issues. - Applied vehicles equipped with the 2G Telematics Control Unit (TCU) that enter the service department for any reason should have the subject TCU deactivated. This campaign will be performed at no charge to the customer for parts or labor. - For customers interested in the TCU update as opposed to deactivation, please refer to ITB17-007. IDENTIFICATION NUMBER Infiniti has assigned identification number P7331 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer?s inventory.
ITB09-015h
Service Bulletin/Repair Instructions
12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.
ITB17-039
Service Bulletin/Repair Instructions
INTERIOR LAMPS INOPERATIVE IF YOU CONFIRM The interior lamps are inoperative (including map lamps, 2nd row personal lamps, door panel step lamps, and trunk lamps). NOTE: If this issue should occur, the outside door handle lamps will also be inoperative. ACTION 1. Set the parking brake. 2. Pull out the extended storage switch/fuse to the ?inventory/storage? position. 3. Start the engine. 4. Confirm the interior lamps are now working correctly. 5. Push in the extended storage switch/fuse to the ?customer delivery? position. NOTE: If the above steps do not resolve the issue, refer to the Electronic Service Manual (ESM) for further diagnostic and repair information.
ITB13-055b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.
ITB15-010c
Service Bulletin/Repair Instructions
INFINITI; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard previous versions of this bulletin.
ITB17-002a
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin does not apply to hybrid vehicles. This bulletin has been amended. The Title has been changed. The PARTS INFORMATION and CLAIMS INFORMATION sections have been amended. Discard previous versions of this bulletin.
ITB17-031
Service Bulletin/Repair Instructions
2016-2017 QX60 AND QX60 HYBRID; REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles, some wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin.
ITB15-012g
Service Bulletin/Repair Instructions
2013 JX35 AND 2014 - 2017 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehciles equipped with a 6 cylinder engine. This bulletin has been amended to add model years to the Applied Vehicles and change the parts information. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-035a
Service Bulletin/Repair Instructions
2015-2017 QX60; ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin applies only to vehicles equipped with a 6 cylinder engine. This bulletin has been amended to add 2017 model year and add part numbers to Table A. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-026
Service Bulletin/Repair Instructions
INFINITI; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
ITB17-016
Service Bulletin/Repair Instructions
2014 - 2016 QX60 OCCUPANT CLASSIFICATION SYSTEM RETROFIT SERVICE INFORMATION The information in this bulletin is provided for customers who have concerns with their Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on.
REVISION 3-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from January 3, 2017 has been revised to include: - Campaign repair bulletin, ITB17-007 has been developed and is now available on NNAnet, and ASIST. Please discard earlier versions of this bulletin.
ITB17-007
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2G TELEMATICS HARDWARE REPLACEMENT This bulletin applies to vehcile equipped with navigation systems only. SERVICE INFORMATION On February 26, 2016 Infiniti announced that it was sending a reminder notification to clients affected by AT&T?s planned discontinuation of the 2G cellular network. In June 2016, Infiniti communicated instructions to retailers to update new vehicles in their inventory with 3G compatible telematics control units. At this time, Infiniti is beginning the process of making 3G compatible hardware available to owners of affected vehicles as identified above. This upgrade may require an owner to make a co-payment in order to receive the 3G hardware update. Please refer to the Claims Information below to determine if an owner co-pay is required. This client satisfaction initiative includes both the hardware upgrade and a complimentary one-year subscription to Infiniti Connection Plus telematics service; this does not apply to PC454 (see page 2 for details). You MUST use Service Comm to confirm bulletin Applicability. NOTE: - Vehicle eligibility will be viewed on the second page of Service Comm. This activity is not displayed on the main page of Service Comm because it is optional for customers to participate. - Vehicles without Navigation are ineligible as they are not equipped with TCUs. Retailer?s Responsibility It is the retailer?s responsibility to check SERVICE COMM using the appropriate Service Comm I.D. for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB17-002
Service Bulletin/Repair Instructions
INFINITI; OIL LEAKING AROUND TIMING CONTROL SOLENOID VALVE This bulletin does not apply to hybrid vehicles. IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve. And The valve timing control solenoid valve operates correctly and is not externally damaged, ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.
ITB17-001
Service Bulletin/Repair Instructions
2014 - 2017 QX60; FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin applies only to AWD equipped vehicles. IF YOU CONFIRM Fluid is leaking from the right side of the transfer assembly (see Figure 1). NOTE: The fluid leak is not caused by the seal shown in Figure 1. ACTION 1. DO NOT REPLACE the transfer assembly. 2. Reseal the transfer assembly. - Refer to the Electronic Service Manual (ESM), section DLN ? Driveline, for transfer assembly removal, reseal, and installation information. - Refer to page 2 and 3 for additional information. CAUTION: Be careful not to damage the transfer assembly right side drive shaft seal when reinstalling the drive shaft.
ITB12-076c
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. Step 15 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
REVISION 2-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from November 3, 2016 has been revised to include: - 283B0-3JA6A is the part number being used for all vehicles, except Q50 o This part supersedes the previous part (283B0-3JA5A). Retailers may continue to use the previous part until existing stock is exhausted. - 283B0-3JA7A is used for Q50 - These parts are not restricted and can be ordered through normal process Please discard previous versions of this announcement.
ITB12-076b
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION The Applied Vehicles in this bulletin have been amended. No other charges have been made. Please discard previous versions of this bulletin.
ITB13-052a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB16-047
Service Bulletin/Repair Instructions
INFINITI; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
REVISION 1-PC451
Service Bulletin/Repair Instructions
2G Telematics Hardware Replacement Client Satisfaction Initiative The announcement from September 2, 2016 has been revised to include: - The telematics upgrade for 2014-15 Q50 is now available. The procedure and part information has been added to this announcement.. - Second page of Service Comm is not VIN specific, service personnel should check vehicle repair history prior to offering clients an opportunity to upgrade - In lieu of repair history, TCU version can be checked on the information screen (see page 2) Please discard previous versions of this announcement.
ITB13-035b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
ITB12-011g
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-039
Service Bulletin/Repair Instructions
2014-2016 QX60; DOORS DIFFICULT TO CLOSE WITH TEMPERATURES BELOW FREEZING IF YOU CONFIRM: THE FOLLOWING INCIDENT, OR THE CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14°F (-10°C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR.
ITB12-011F
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION VEHICLES EQUIPPED WITH FACTORY NAVIGATION SYSTEM THIS BULLETIN HAS BEEN AMENDED. MODIFICATIONS HAVE BEEN MADE TO INCLUDE QX30. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
ITB16-032
Service Bulletin/Repair Instructions
2016 QX60 AND QX60 HYBRID; AROUND VIEW MONITOR MIRROR CAMERA INOPERATIVE IF YOU CONFIRM - EITHER THE LEFT OR RIGHT AROUND VIEW MONITOR DOOR MIRROR CAMERA IS INOPERATIVE. NOTE: THE FOLLOWING DTCS MAY ALSO BE PRESENT: - U111B (SIDE CAMERA LH IMAGE SIGNAL CIRCUIT) DTC IS STORED. AND/OR - U111D (SIDE CAMERA RH IMAGE SIGNAL CIRCUIT) DTC IS STORED. ACTION CHECK THE SIDE CAMERA HARNESS CONNECTION BETWEEN THE SIDE CAMERA AND THE MIRROR HARNESS LOCATED INSIDE THE INOPERATIVE DOOR MIRROR. - IF THE HARNESS CONNECTOR IS NOT LATCHED (CAN BE DISCONNECTED BY A GENTLE TUG), SEAT THE CONNECTOR, CLEAR THE DTC AND RETEST. - IF THE HARNESS CONNECTOR IS LATCHED (CANNOT BE DISCONNECTED BY A GENTLE TUG) REFER TO THE ELECTRONIC SERVICE MANUAL (ESM) FOR FURTHER DIAGNOSTIC INFORMATION. NOTE: IF A SIDE CAMERA REQUIRES REPLACEMENT, DO NOT REPLACE THE ENTIRE MIRROR, REPLACE ONLY THE SIDE CAMERA.
ITB16-031
Service Bulletin/Repair Instructions
2016 QX60; AUTOMATIC BACK DOOR CALIBRATION PROCEDURE SERVICE INFORMATION AS OF THE PUBLICATION DATE OF THIS BULLETIN, THE AUTOMATIC BACK DOOR CALIBRATION PROCEDURE IN THE ELECTRONIC SERVICE MANUAL (ESM) IS INCORRECT. IF FOR ANY REASON THE AUTOMATIC BACK DOOR REQUIRES CALIBRATION, USE THE PROCEDURE IN THIS BULLETIN.
ITB16-028
Service Bulletin/Repair Instructions
2016 QX60 LANE CAMERA AIMING SERVICE INFORMATION THE ELECTRONIC SERVICE MANUAL (ESM) PAGES FOR LANE CAMERA AIMING IN THE DAS SECTION HAVE BEEN UPDATED/AMENDED. UNTIL THE UPDATED SERVICE MANUALS ARE MADE AVAILABLE, PLEASE REFER TO THE LINK BELOW, AS NEEDED, FOR ANY SERVICE OR REPAIRS RELATED TO THE 2016 QX60 LANE CAMERA.
ITB16-030
Service Bulletin/Repair Instructions
2016 QX60; SOME AUTOMATIC BACK DOOR DTC DESCRIPTIONS ARE NOT DISPLAYED ON CONSULT-III PLUS SERVICE INFORMATION THE DESCRIPTIONS FOR AUTOMATIC BACK DOOR DTCS IN THE TABLE BELOW DO NOT DISPLAY ON CONSULT-III PLUS (C-III PLUS). ONLY THE DTC ALPHANUMERIC DESIGNATION IS DISPLAYED. USE THE TABLE BELOW TO IDENTIFY THE DTC DESCRIPTION AND ITS LISTING IN THE ELECTRONIC SERVICE MANUAL (ESM) OR ASIST.
R1621 2016 QX60
Service Bulletin/Repair Instructions
REAR O2 SENSOR VOLUNTARY EMISSIONS RECALL CAMPAIGN INFINITI IS CONDUCTING A VOLUNTARY EMISSIONS RECALL CAMPAIGN TO UPDATE THE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE ON CERTAIN MODEL YEAR 2015-16 INFINITI QX60 VEHICLES. UNDER CERTAIN CONDITIONS, THE REAR OXYGEN (O2) SENSOR SIGNAL COULD FAIL, RESULTING IN THE REAR OXYGEN (O2) SENSOR OBD MONITOR BEING DISABLED WITHOUT THE CLIENT BEING ALERTED. INFINITI PLANS TO BEGIN NOTIFYING OWNERS OF AFFECTED VEHICLES IN AUGUST, ASKING THEM TO BRING THEIR VEHICLES TO AN AUTHORIZED INFINITI RETAILER. ***** WHAT RETAILERS SHOULD DO**** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSION RECALL CAMPAIGN USING SERVICE COMM I.D. R1621. NOTE: NEW VEHICLES IN RETAILER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN). - REFER TO IPSB 15-286 FOR ADDITIONAL INFORMATION 2. THE SUBJECT VEHICLES ARE NOT ON SALES HOLD, BUT FOR CLIENT CONVENIENCE, RETAILERS ARE ENCOURAGED TO PERFORM THIS CAMPAIGN ON ANY AFFECTED VEHICLES IN THEIR INVENTORY PRIOR TO SALE, LEASE, OR TRADE. 3. RETAILERS SHOULD USE ITB16-027 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, RETAILER SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE.
ITB16-027
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2015-2016 QX60 ECM REPROGRAMMING INTRODUCTION INFINITI IS CONDUCTING A VOLUNTARY EMISSION RECALL CAMPAIGN ON CERTAIN MODEL YEAR 2015-2016 QX60 VEHICLES. INFINITI HAS DISCOVERED THAT THESE VEHICLES ARE EQUIPPED WITH AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION THAT, IF NOT REPAIRED, MAY NOT DETECT A REAR OXYGEN (O2) SENSOR SHORT-TO-GROUND OR SHORT-TO-BATTERY CONDITION. THE ECM (ENGINE CONTROL MODULE) WILL BE REPROGRAMMED. THIS SERVICE WILL BE PERFORMED AT NO CHARGE FOR PARTS OR LABOR. IDENTIFICATION NUMBER INFINITI HAS ASSIGNED IDENTIFICATION NUMBER R1621 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM FOR THE CAMPAIGN STATUS ON EACH VEHICLE FALLING WITHIN THE RANGE OF THIS VOLUNTARY EMISSIONS RECALL WHICH FOR ANY REASON ENTERS THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES OR PRESENTED BY TRANSIENT (TOURIST) OWNERS AND VEHICLES IN A DEALERS INVENTORY.
ITB14-011C
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 4 AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: "PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM.
ITB15-026A
Service Bulletin/Repair Instructions
INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST.
PC454
Service Bulletin/Repair Instructions
ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS SHOULD NOT SELL OR TRADE ANY AFFECTED VEHICLES IN RETAILER INVENTORY SUBJECT TO THIS SERVICE ACTION UNTIL THE 3G-COMPATIBLE TELEMATICS CONTROL UNIT HAS BEEN INSTALLED.
REVISION1-PC454
Service Bulletin/Repair Instructions
THIS ANNOUNCEMENT HAS BEEN REVISED TO CLARIFY THIS ACTIVITY IS NOT AN OFFICIAL STOP SALE. RETAILERS MAY SELL VEHICLES THAT HAVE NOT BEEN UPGRADED. PLEASE REFER TO ADDITIONAL Q&A SUPPLIED IN THIS DOCUMENT. PLEASE DISCARD EARLIER VERSIONS OF THIS BULLETIN. ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS ARE REQUESTED TO INSTALL A 3G-COMPATIBLE TELEMATICS CONTROL UNIT IN VEHICLES AFFECTED BY THIS SERVICE ACTION PRIOR TO RETAIL TO ENSURE CLIENT SATISFACTION.
ITB09-059D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY ITB15-026. INFINITI; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
ITB11021B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.
ITB15012F
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - ITB15-010, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on the next page. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
ITB16016
Service Bulletin/Repair Instructions
SERVICE INFORMATION Nissan is issuing this Technical Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and 'passenger airbag indicator' (PABI), as described in the Owner?s Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: * PABI light is ON with an empty front passenger seat. Please see this bulletin for further details.
ITB09041A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
ITB09063B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
AT14-017B
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB15010B
Service Bulletin/Repair Instructions
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
ITB13-055A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB13055A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. Please see this bulletin for further information.
ITB15021A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
AT15-007E
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ITB03051J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
PC452
Service Bulletin/Repair Instructions
Beginning February 29th, owners of the affected Infiniti vehicles equipped with Telematics Control Units (TCU) will receive a letter notification explaining how their vehicle?s Infiniti Connection features will be affected by AT&T?s planned discontinuation of the 2G cellular network.
ITB16008
Service Bulletin/Repair Instructions
IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
ITB16005
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
ITB16003
Service Bulletin/Repair Instructions
SERVICE INFORMATION Whenever all Intelligent Keys of an APPLIED VEHICLE are lost AND the BCM is in Transit Mode, the BCM does not need to be replaced when replacing the lost Intelligent Keys. When all of the following conditions of an APPLIED VEHICLE are verified: - The BCM is in Transit Mode. - The BCM will not respond to CONSULT-III plus (C-III plus). It does not show up on System Call. - All Intelligent Keys are lost. DO NOT replace the BCM or ECM when replacing the lost Intelligent Keys. The procedure in this bulletin will get the existing BCM out of Transit Mode. See this bulletin for further detail.
PC420
Service Bulletin/Repair Instructions
Infiniti is conducting a Dealer Service Action to inspect, and if necessary, repalce the hood latch on certain MY2015-16 QX60 vehicles.
PC420A
Service Bulletin/Repair Instructions
This activity will expire on December 18th, 2015. Retailers can continue to schedule and repair vehicles eligible for this service action until close of business December 18th, 2015. Claims will be honored for RO?s opened on or before the 18th of December.
ITB15023
Service Bulletin/Repair Instructions
SERVICE INFORMATION When replacing both of the vehicle?s I-Keys, due to being lost prior to vehicle delivery, new I-Keys can now be registered without the BCM (or ECM) being replaced. Do not replace the BCM (or ECM) before replacing I-Keys for theApplied Vehicles. Please see this bulletin for further details.
ITB15020
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
ITB14020
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.