ITB26-002A
Service Bulletin/Repair Instructions
FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of ITB26-002.
Vehicle report
2024 INFINITI QX60
Service bulletins
26 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB26-005
Service Bulletin/Repair Instructions
AEB WARNING WITH ONE OR MORE CURRENT DTCS STORED IN THE ADAS CONTROL UNIT 2, AND/OR THE LASER/RADAR CONTROL UNIT IF YOU CONFIRM The front radar is inoperative, the AEB warning is displayed, and one or more of the following DTCs are stored as CURRENT: · U2752-88 for “Ethernet circuit” stored in the ADAS control unit 2, · U275F-88 for “Ethernet circuit” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, OR · C2589-86 for “TCM” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, AND/OR · C258E-86 for “ABS” stored in the LASER/RADAR (DISTANCE SENSOR) control unit. ACTION 1. Confirm the current Distance Sensor control unit part number. 2. Reprogram the Distance Sensor control unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB26-004
Service Bulletin/Repair Instructions
FRONT FASCIA POPPING OUT NEAR HEADLAMP IF YOU CONFIRM The Front Bumper Fascia is detaching from the fender under the headlamp on one/or both sides. ACTION Refer to the SERVICE PROCEDURE in this bulletin to: 1. Remove the Front Bumper Fascia. 2. Replace the affected Headlamp Bracket. 3. Replace the affected Front Bumper Fascia Side Bracket. 4. Reinstall the Front Bumper Fascia, with Betaseal (or equivalent) adhesive between the Front Bumper Fascia and the affected side Front Bumper Fascia Side Bracket.
ITB26-002
Service Bulletin/Repair Instructions
FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB25-008
Service Bulletin/Repair Instructions
EXCESS DUST ENTERING CABIN WHILE DRIVING ON DIRT ROADS IF YOU CONFIRM That while driving on dirt roads with all doors and windows closed, that there is excessive dust intrusion into the vehicle’s cabin that is settling on the inside of the doors. ACTION Refer to the SERVICE PROCEDURE in the bulletin to: 1. Install Butyl Patches around the door seals of driver (LH) side and passenger (RH) side front and rear doors. 2. Install drain plugs into door drains of driver (LH) side and passenger (RH) side front and rear doors.
ITB25-005
Service Bulletin/Repair Instructions
AIR CONDITIONING IS INOPERATIVE WITH LEAK FROM HIGH/LOW SIDE PIPE JUNCTION IF YOU CONFIRM The client states that the A/C is not blowing cold or is blowing warm on driver’s side vents, AND Leak detection dye is confirmed as present on the high-pressure and low-pressure A/C pipe junction blocks. HINT: See Refrigerant Leak Examples on page 2. ACTION Replace the A/C High-Pressure and Low-Pressure Pipe. · Refer to the ESM: VENTILATION, HEATER & AIR CONDITIONER > HEATER & AIR CONDITIONING SYSTEM > REMOVAL AND INSTALLATION > COOLER PIPE AND HOSE > HIGH-PRESSURE AND LOW-PRESSURE PIPE > Removal
ITB25-002
Service Bulletin/Repair Instructions
DRIVABILITY CONCERNS AT HIGHWAY SPEEDS AND ON INCLINES IF YOU CONFIRM A lugging / shutter / judder at highway speeds, especially on slight inclines, ACTION Reprogram the Electronic Control Module (ECM). IMPORTANT:
ITB23-023A
Service Bulletin/Repair Instructions
AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB22-021C
Service Bulletin/Repair Instructions
SERVICE INFORMATION In the APPLIED VEHICLES, there are a variety of Seat Belt Warning Lights and Chimes. Refer to the information in this bulletin, along with the related vehicle owner’s manual. Figure 1 Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. Seat Belt Warning Light for driver and front passenger.
ITB19-029E
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION Vehicles equipped with factory telematics system HINT: If the client experiences Wi-Fi hotspot related concerns only, DO NOT replace the TCU. Have the client contact the AT&T Support line at 1 (888) 719-7242. See ITB12-011 for models built before those listed above. SERVICE INFORMATION The APPLIED VEHICLES are equipped with a wireless communication device called a Telematics Communication Unit (TCU). The TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. An Order of Completion table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. A CHECK-OFF SHEET has been provided on page 16. Print and check off steps as they are completed. Staple the completed CHECK-OFF SHEET to the repair order.
ITB22-017B
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC APPLIED SYSTEMS: Vehicles equipped with Telematics SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB24-009
Service Bulletin/Repair Instructions
VIBRATION AND/OR NOISE FROM THE REAR OF THE VEHICLE APPLIED VEHICLES: 2022-2024 QX60 (L51) APPLIED DATES: Built on or before February 28, 2024 APPLIED DRIVETRAINS: AWD IF YOU CONFIRM A binding feeling, vibration, and/or noise coming from the rear end when turning at low speed or accelerating from a stop, AND The issue is resolved by unplugging the Actuator Assembly (AWD Actuator) on the rear Final Drive Unit. ACTION Refer to the SERVICE PROCEDURE below to: 1. Remove the Electro-hydraulic Coupling Assembly (AWD Coupler). 2. Clean the Coupling Oil Tank. 3. Inspect the Breather Tube and Bolt. 4. Replace the Electro-hydraulic Coupling Assembly (AWD Coupler). IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB22-001A
Service Bulletin/Repair Instructions
INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
ITB22-002A
Service Bulletin/Repair Instructions
BCM SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
ITB22-003A
Service Bulletin/Repair Instructions
REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB24-005
Service Bulletin/Repair Instructions
POPPING NOISE FROM FRONT SUSPENSION WHEN TURNING SERVICE INFORMATION Individual strut components are available to service specific issues that have been diagnosed in a strut assembly. If a strut has been confirmed as having a popping noise while turning, refer to the Repair Overview flow chart on page 2 to confirm that the SERVICE PROCEDURE on page 3 applies. HINT: The SERVICE PROCEDURE in this bulletin is only meant to supplement the information found in the Electronic Service Manual (ESM). Refer to the ESM for information to remove and service the vehicle’s struts.
ITB19-013E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-027
Service Bulletin/Repair Instructions
POWER FOLDING 3RD ROW SEAT SYSTEM CALIBRATION SERVICE INFORMATION Obstructions such as unfolded headrests or objects left in the vehicle may prevent the power folding 3rd row seat from returning to the upright position under power: ï· Verify that the 3rd row seat headrests are folded forward. o If the 3rd row seat headrests are not folded forward, the headrests can contact the 2nd row seats and prevent the power folding 3rd row seat from returning upright. ï· Verify that the floor between the 2nd and 3rd row seats is clear of any obstructions. o If there are obstructions on the floor, clear the obstructions and try to move the seat upright. ï· If the 3rd row seat headrests are folded forward and there are no obstructions, perform system calibration before attempting to replace any parts. o Refer to the ESM: BODY INTERIOR > SEAT > BASIC INSPECTION > SYSTEM CALIBRATION > Work Procedure If the power folding 3rd row seat does not return upright under power after performing system calibration, refer to the ESM for further diagnosis.
ITB22-021B
Service Bulletin/Repair Instructions
SEAT BELT REMINDER SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC988 2023 QX60
Service Bulletin/Repair Instructions
Seat Frame Weld ***** Retailer Announcement ***** INFINITI is conducting a retailer inventory quality action to inspect, and if necessary replace the seat frame assembly on certain specific 2024 INFINITI QX60 vehicles identified in Service Comm and National Service History. The lower front seat cushion with 8-way power control may feel loose or emit a noise when seat cushion is adjusted to upward position using tilt feature. Please follow the attached instructions to remedy any vehicles affected by this retailer inventory quality action. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PC988 ï· New vehicles in retailer inventory can also be identified by using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to IPSB 15-286 for additional information ï· Some vehicles may still be in transit. Please continue to check newly arriving inventory for QA applicability. 2. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 3. Parts for this quality action are on restriction and can be ordered through DBS. 4. Once remedied, retailers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle for sale. ***** Retailer Responsibility ***** It is the retailerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
ITB22-036A
Service Bulletin/Repair Instructions
DTCS B2E4B-06, B2E60-06, B2E61-06 DISPLAYED AS CRNT IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.