Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
ITB09-063C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB23-023A
Service Bulletin/Repair Instructions
AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB19-024D
Service Bulletin/Repair Instructions
DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB22-021C
Service Bulletin/Repair Instructions
SERVICE INFORMATION In the APPLIED VEHICLES, there are a variety of Seat Belt Warning Lights and Chimes. Refer to the information in this bulletin, along with the related vehicle owner’s manual. Figure 1 Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. Seat Belt Warning Light for driver and front passenger.
ITB19-029E
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION Vehicles equipped with factory telematics system HINT: If the client experiences Wi-Fi hotspot related concerns only, DO NOT replace the TCU. Have the client contact the AT&T Support line at 1 (888) 719-7242. See ITB12-011 for models built before those listed above. SERVICE INFORMATION The APPLIED VEHICLES are equipped with a wireless communication device called a Telematics Communication Unit (TCU). The TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. An Order of Completion table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. A CHECK-OFF SHEET has been provided on page 16. Print and check off steps as they are completed. Staple the completed CHECK-OFF SHEET to the repair order.
ITB19-042E
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The AV control unit needs to be replaced. ACTION 1. Read and save the VIN. 2. Read and save the configuration. 3. Replace the AV control unit. 4. Reprogram the AV control unit. 5. Configure the AV control unit. 6. Write the VIN to the AV control unit. IMPORTANT: Procedures 4-6 above must be performed in the order shown below. ORDER OF COMPLETION REPROGRAM AV Control Unit CONFIGURE AV Control Unit WRITE VIN to AV Control Unit Infiniti
ITB22-017B
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC APPLIED SYSTEMS: Vehicles equipped with Telematics SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-020B
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled and the TCU must be reset to re-enable the automatic collision notification function. Some models will store DTC B2E1B-97 for “Automatic eCAll locked” as “CURRENT” when this function is disabled. This bulletin describes how to reset the TCU after an automatic collision notification has been performed. For models with B2E1B-97 for “Automatic eCAll locked” set as “CURRENT”, complete the SERVICE PROCEDURE starting on page 2, and then erase DTCs after confirming the TCU condition is “UNLOCK”.
ITB23-015A
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN THE IVC APPLIED VEHICLES: 2020-2024 Q50 (V37) 2020-2022 Q60 (CV37) 2020-2024 QX80 (Z62) SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. When diagnosing DTC B2E1B-06 for “AUTOMATIC ECALL” on an APPLIED VEHICLE: If DTC B2E1B-06 is not “CRNT” in the IVC, do not replace the TCU. Erase the DTC. No further steps are needed. If DTC B2E1B-06 is “CRNT” in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page.DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN THE IVC APPLIED VEHICLES: 2020-2024 Q50 (V37) 2020-2022 Q60 (CV37) 2020-2024 QX80 (Z62) SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. When diagnosing DTC B2E1B-06 for “AUTOMATIC ECALL” on an APPLIED VEHICLE: If DTC B2E1B-06 is not “CRNT” in the IVC, do not replace the TCU. Erase the DTC. No further steps are needed. If DTC B2E1B-06 is “CRNT” in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Please discard previous versions of this bulletin.
ITB10-029C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052E
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-025B
Service Bulletin/Repair Instructions
DTC C1A17-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-009H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of ITB23-010.
ITB22-027B
Service Bulletin/Repair Instructions
ENABLING WIRELESS APPLE CARPLAY® FEATURES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of ITB23-010.
ITB22-021B
Service Bulletin/Repair Instructions
SEAT BELT REMINDER SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-043A
Service Bulletin/Repair Instructions
INFOTAINMENT CONTROL UNIT REPLACEMENT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-011G
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-027A
Service Bulletin/Repair Instructions
ENABLING WIRELESS APPLE CARPLAY® FEATURES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-015
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN IVC SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. 1. When diagnosing DTC B2E1B-06 (AUTOMATIC ECALL) on an APPLIED VEHICLE: ï· If DTC B2E1B-06 is not âCRNTâ in the IVC, DO NOT replace the TCU. Erase the DTC. No further steps are needed. ï· If DTC B2E1B-06 is âCRNTâ in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU
ITB03-051Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008D
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-021E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: ITB23-010 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
ITB19-013D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-025A
Service Bulletin/Repair Instructions
DTC C1A17-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-021A
Service Bulletin/Repair Instructions
SEAT BELT REMINDER SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-074B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-010
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the client is experiencing a software related concern, refer to ITB21-011 to verify if the client concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
ITB09-039J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-007H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-067C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-006C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-030C
Service Bulletin/Repair Instructions
AV CONTROL UNIT INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-042D
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-020A
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-017A
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB23-002
Service Bulletin/Repair Instructions
MISSING OR CORRUPTED MAP DATA IF YOU CONFIRM Client states the error screen, shown in Figure 1, appears when using navigation. ACTION Follow the SERVICE PROCEDURE in this bulletin to download the map data from the ASIST Downloader, and then update the AV Control Unit with the map data.
ITB22-043
Service Bulletin/Repair Instructions
INFOTAINMENT CONTROL UNIT REPLACEMENT SERVICE INFORMATION SERVICE INFORMATION When replacing an AV control unit (Infotainment Control Unit), for any reason, all three steps below are required. If all three steps are not completed on vehicles equipped with a TCU, the Over The Air (OTA) updates will not work, and other functions may be inoperative. HINT: Not all APPLIED VEHICLES are OTA-update capable. 1. Reprogram the AV control unit. 2. Configure the AV control unit. 3. Write the VIN to the AV control unit. IMPORTANT: Steps 1-3 above must be performed in the sequential order shown below.
ITB22-041
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.
ITB19-029D
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB13-008C
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-013A
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2020-2021 QX80; INFOTAINMENT SOFTWARE UPDATE AND WIRELESS CARPLAY CONFIGURATION Client Satisfaction Initiative ID # PC882 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Client Satisfaction Initiative ID # PC882. ï· Discard all previous versions of ITB22-013.
ITB22-027
Service Bulletin/Repair Instructions
ENABLING WIRELESS APPLE CARPLAY® FEATURES SERVICE INFORMATION To enable wireless use of current Apple CarPlay® features, follow the SERVICE PROCEDURE in this bulletin. NOTE: Depending on the software version, the AV control unit may need to be updated. Perform steps 1-4 beginning on page 3 to check the software version.
ITB22-021
Service Bulletin/Repair Instructions
SEAT BELT REMINDER SERVICE INFORMATION SERVICE INFORMATION On the APPLIED VEHICLES, there are a variety of Seat Belt Warning Lights and Chimes. Refer to the information in this bulletin, along with the related vehicle ownerâs manual.
ITB19-024B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-020
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled and the TCU must be reset to re-enable the automatic collision notification function. Some models will store DTC B2E1B-97 (Automatic eCAll locked) as âCURRENTâ when this function is disabled. This bulletin describes how to reset the TCU after an automatic collision notification has been performed. For models with B2E1B-97 (Automatic eCAll locked) set as âCURRENTâ, complete the SERVICE PROCEDURE starting on page 2, and then erase DTCs after confirming TCU condition is âUNLOCKâ.
ITB22-017
Service Bulletin/Repair Instructions
B2E01-96 (INTERNAL BATTERY) DTC STORED AS CURRENT IN IVC SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEURE starting on page 2.
ITB22-015
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
PC882 2020-21 QX
Service Bulletin/Repair Instructions
Wireless Apple CarPlay® Update Voluntary Service Campaign ***** Campaign Summary ***** INFINITI is continuing to conduct a Client Service Initiative (CSI) on certain specific model year 2020-2021 QX80 vehicles that were previously included and subsequently removed and suspended from the initiative under PC839. The previous software update did not fully address the intended concerns. INFINITI is launching a new CSI that will provide clients with a free Infotainment software update, which includes Wireless Apple CarPlay®. The CSI will be available until June 30, 2022. The update will bring the vehicleâs software to current production level, improve system overall performance, and enable clientâs use of Apple CarPlay® wirelessly. For more information on Apple CarPlay®, please refer to: INFINITI Apple CarPlay® Features & FAQs INFINITIâs InTouch system is designed to improve the driving experience. Certain Model Year 2020 and 2021 INFINITI vehicles are already equipped with Apple CarPlay® to enhance iPhone usersâ experience with iOS13 and later, but they currently require a USB cord connection to an iPhone to use. The update eliminates the need to remove the iPhone from oneâs pocket or bag. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaign I.D. PC882 ⢠New vehicles in retailer inventory can also be identified by using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to IPSB 15-286 for additional information 2. Retailers should ensure any applicable vehicle has the latest AV control unit software installed, and use ITB22-013 to update the following software: ⢠Enablement of Wireless Apple CarPlay® ⢠Stability improvements and âbugâ fixes
ITB22-013
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2020-2021 QX80; INFOTAINMENT SOFTWARE UPDATE AND WIRELESS CARPLAY CONFIGURATION SERVICE INFORMATION Infiniti is providing a free infotainment software update, including Wireless Apple CarPlay®, until June 30, 2022. This upgrade will bring the vehicleâs infotainment software up to current production level, improve system overall performance, and enable wireless use of current Apple CarPlay® features. RETAILER RESPONSIBILITY It is the retailerâs responsibility to check SERVICE COMM using Service Comm I.D. PC882 for the status on each vehicle falling within the range of this client satisfaction initiative, which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB20-021D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-029C
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-030B
Service Bulletin/Repair Instructions
AV CONTROL UNIT INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-042C
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-006C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-052D
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB22-006
Service Bulletin/Repair Instructions
BATTERY QUICK CHARGE NOTICE SERVICE INFORMATION When charging the vehicleâs 12 volt battery with the high amperage quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. ï· Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. ï· Battery voltage should not exceed 16V during a reprograming operation.
ITB13-044J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-031
Service Bulletin/Repair Instructions
OIL LEAK AT REAR OF TRANSMISSION SERVICE INFORMATION When diagnosing an oil leak at the rear of the transmission on an applied vehicle, follow the SERVICE PROCEDURE in this bulletin to determine if the origin of the leak is at the rear extension seal, or at the pressed-in plug of the propeller shaft sleeve yoke (Figure 1).
REV 2 - PC839 20
Service Bulletin/Repair Instructions
Wireless Apple CarPlay® Update Voluntary Service Campaign UPDATE December 16, 2021 Please discard earlier versions of this bulletin. The announcement from October 18, 2021 has been updated to highlight the following important information: ï· Review of additional production records has allowed INFINITI to more accurately identify the production window of vehicles potentially within scope of this activity. As a result, the population of applicable QX50 vehicles has increased for this activity.
ITB03-051P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-033C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074P
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-006B
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-022A
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2020-2021 Q50, Q60, QX50, AND QX80; INFOTAINMENT SOFTWARE UPDATE AND WIRELESS CARPLAY CONFIGURATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
REV 1 - PC839 20
Service Bulletin/Repair Instructions
Wireless Apple CarPlay® Update Voluntary Service Campaign UPDATE October 18, 2021 Please discard earlier versions of this bulletin. The announcement from October 6, 2021 has been updated to highlight the following important information: ï· Retailers should ensure they are using the most recent version of the CONSULT III operating system. ï· Ensure that the technician has configured the audio/IT unit as instructed beginning with step 27 of the Technical Service Bulletin (TSB). ï· Retailers should assist every customer with (1) removing ALL paired phones,(2) pairing their phone with the vehicle again before they leave the dealership, and (3) verifying Wireless CarPlay is working for iPhone users (See page 2 of this announcement) ï· Ensure that YES is selected on the vehicle when prompted to deactivate Wi-Fi to use Wireless CarPlay (provide owners a copy of the instructions on page 6 of this announcement) Notify owners that some vehicles may have initial location accuracy concerns after the software update. This is not a unique issue for INFINITI and will self-correct within a few days.(see page 7) Please print a copy of the phone pairing instructions (page 6) for the owner to use with pairing other phones back to their vehicle.
PC839 2020-21 Q5
Service Bulletin/Repair Instructions
Wireless Apple CarPlay® Update Voluntary Service Campaign ***** Campaign Summary ***** INFINITI is conducting a Client Service Initiative to provide a free Infotainment software update, which includes Wireless Apple CarPlay® until March 31, 2022. The update will bring the vehicleâs software to current production level, improve system overall performance, and enable you to use Apple CarPlay® wirelessly! For more information on Apple CarPlay®, please refer to: INFINITI Apple CarPlay® Features & FAQs INFINITIâs InTouch system is designed to improve the driving experience. Your vehicle is already equipped with Apple CarPlay® to enhance your iPhone user experience with iOS13 and later, but it currently requires a USB cord connection to your phone to use. The CarPlay® dashboard takes things you want to do with your iPhone while driving and puts them right on the vehicleâs built-in display, eliminating the need to remove the iPhone from your pocket or bag. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaign I.D. PC839 ï· New vehicles in retailer inventory can also be identified by using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to IPSB 15-286 for additional information 2. Retailers should ensure any applicable vehicle has the latest AV control unit software installed, and use ITB21-022 to update the following software: ï· Enablement of Wireless Apple CarPlay® ï· Stability improvements and âbugâ fixes 3. Retailers should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.
ITB21-022
Service Bulletin/Repair Instructions
CLIENT SATISFACTION INITIATIVE 2020-2021 Q50, Q60, QX50, AND QX80; INFOTAINMENT SOFTWARE UPDATE AND WIRELESS CARPLAY CONFIGURATION SERVICE INFORMATION Infiniti is providing a free infotainment software update, including Wireless Apple CarPlay®, until March 31, 2022. This upgrade will bring the vehicleâs infotainment software up to current production level, improve system overall performance, and enable wireless use of current Apple CarPlay® features. RETAILER RESPONSIBILITY It is the retailerâs responsibility to check SERVICE COMM using Service Comm I.D. PC839 for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.
ITB13-008B
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-026D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB21-010
Service Bulletin/Repair Instructions
UPPER INFOTAINMENT SCREEN TURNS ON AFTER TURNING VEHICLE OFF IF YOU CONFIRM The upper infotainment screen turns ON after the vehicleâs ignition is turned OFF and the door is opened, And The current telematics control unit (TCU) part number is 28275-5SN9B. ACTION Reprogram the telematics control unit (TCU).
ITB19-029B
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB21-007
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
ITB16-006A
Service Bulletin/Repair Instructions
INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-056B
Service Bulletin/Repair Instructions
INTELLIGENT KEY BATTERY DISCHARGED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-021B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D
Service Bulletin/Repair Instructions
INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-013b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-026a
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-029a
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION See ITB12-011 for models built before those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti InTouch Services⢠subscription the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. ï A table has been provided on the next page that lists the model and year-specific steps required to successfully configure a TCU after it has been replaced. ï A check OFF sheet has been provided on page 11 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB17-056a
Service Bulletin/Repair Instructions
INTELLIGENT KEY BATTERY DISCHARGED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-006a
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-026
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled. The TCU must be reset to re-enable the automatic collision notification function. This bulletin describes how to reset the TCU after an automatic collision notification has been performed.
ITB19-013a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.