Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK0600030
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK1201009
In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of humidity, an operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK3400001
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0500054
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600286
Title: Vehicle Programming Information for Engine: Single Box 1998-2004 I6 & V8 Applies To: Single Box 1998-2004 I6 & V8
IK2600069
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK0300078
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK1400023
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK1000003
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK1201299
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK1600131
Cab water leak troubleshooting tips
IK0400040
General wheel speed sensor troubleshooting
IK0100051
Frame Rail Straightness Inspection Procedure
IK0200013
Suggested alignment target values when performing a vehicle axle alignment
IK0800504
Repair Procedures for Vehicles Struck by Lightning
IK1600258
Cleaning and Disinfecting Trucks and Buses
IK0800224
Power Distribution Center (PDC) Replacement; 7000 (Workstar) Model Series with Allison or Manual Transmissions
IK0800533
Key Codes and Key Cutting Information (Not for CV Series)
4328530R1
Tool Instruction - BCM Programming Harness
IK0800475
Radio Diagnostics and Information
IK4300001
Updating OnCommand Link with Accelerator
IK0800080
J1939 Data Link Troubleshooting
IK1200921
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
IK2700100
OnCommand EZ-Tech
IK2500511
Using Supplier Software to Check DTCs
IK0800341
Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
IK0500038
Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
IK0500058
Steering Fluids
IK0800351
J1939 Data Link Source Address Information
IK1201248
Cooling System Flush Procedure
IK1200029
RADIATOR INTERNAL RESTRICTION AND FLUSH PROCEDURE
061302
GUIDELINES TO ENSURE SATISFACTORY PERFORMANCE OF MERITOR TRANSFER CASE MODELS MTC-4208, MTC-4210, MTC-4213 IN CERTAIN INTERNATIONAL 7000 HPV MODELS. *TT
061208
THE ENGINE TURBOCHARGER CLEAN AIR INTAKE HOSE NIPPLE THAT PROVIDES AIR TO THE AIR COMPRESSOR MAY DISCONNECT FROM THE INTAKE HOSE IN A LIMITED NUMBER OF INTERNATIONAL 7300 MODELS BUILT BETWEEN DECEMBER 01, 2004 WITH INTERNATIONAL I-6 ENGINES. *TT
050501
CORRECT METHOD TO DETERMINE POWER STEERING RESERVOIR OIL FILL LEVEL FOR INTERNATIONAL MODELS WITH 2002 EMISSION ENGINES AND BUS MODELS BUILT AFTER 3/12/04. *TT
051206
INSTALLING A HEAT SHIELD TO THE EXHAUST MANIFOLD TO PROTECT THE TURBOCHARGER INLET HOSE ON 7000 MODELS BUILT AFTER JULY 1, 2001 WITH DT 466 ENGINE CODES 12NMG, 12NMH, AND 12NMK. INTERNATIONAL. 2001 MODEL 7600 INCLUDED. *TT
041607
CRITERIA FOR CONDITIONING ACCUMULATOR REPLACEMENT ON HPV MODELS. *TT
04903
REPLACE MERITOR TRANSFER CASE IL PUMP WITH NEW DESIGN OIL PUMP IN 7300, 7400, 7500 4X4 AND 6X6 MODELS BUILT BETWEEN SEPTEMBER 27, 2001 AND SEPTEMBER 15, 2003. INTERNATIONAL MODELS 7300, 7400, 7500 START DATE 09/01 END DATE 09/03. *MJ
0438
HVAC SETTING FAULT CODE 613-14-1-6 PREMATURELY. *MJ
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.