IK2600159
Service Bulletin/Repair Instructions
There are two ways to program 5000 and 9000 odometer. You can use Intune or Instrument Cluster Program also known as IPC to correctly set the mileage for the odometer.
Vehicle report
2016 INTERNATIONAL 9900
Service bulletins
84 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1900198
Service Bulletin/Repair Instructions
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK2600090
Other
New CARB Idle Reduction Change Request
IK4300035
Service Bulletin/Repair Instructions
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600255
Other
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2600047
Service Bulletin/Repair Instructions
Engine replacements for all International engines will need to follow this procedure.
IK1600272
Service Bulletin/Repair Instructions
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK0600030
Service Bulletin/Repair Instructions
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK1201009
Service Bulletin/Repair Instructions
In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of humidity, an operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK3400001
Service Bulletin/Repair Instructions
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Service Bulletin/Repair Instructions
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Service Bulletin/Repair Instructions
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Service Bulletin/Repair Instructions
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Service Bulletin/Repair Instructions
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0500054
Service Bulletin/Repair Instructions
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Service Bulletin/Repair Instructions
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK0300078
Service Bulletin/Repair Instructions
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK1400023
Service Bulletin/Repair Instructions
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0200013
Service Bulletin/Repair Instructions
Suggested alignment target values when performing a vehicle axle alignment.
IK0800407
Service Bulletin/Repair Instructions
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
IK0800351
Service Bulletin/Repair Instructions
J1939 Data Link Source Address Information
IK0300010
Service Bulletin/Repair Instructions
Diagnosis of chassis wander complaints.
IK0400040
Service Bulletin/Repair Instructions
General Wheel Speed Sensor Troubleshooting
IKo800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1200101
Service Bulletin/Repair Instructions
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK0700115
Service Bulletin/Repair Instructions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
IK1201472
Service Bulletin/Repair Instructions
Pico Scope CCOS (Crankcase Separator Test)
IK0800605
Service Bulletin/Repair Instructions
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
IK0800607
Service Bulletin/Repair Instructions
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
Service Bulletin/Repair Instructions
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
Service Bulletin/Repair Instructions
PicoScope Test Resistance and Ohmmeter
IK1201469
Service Bulletin/Repair Instructions
PicoScope Test One Channel RCT
IK1000003
Service Bulletin/Repair Instructions
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK2600251
Service Bulletin/Repair Instructions
How to obtain As built parameter list
IK1201299
Service Bulletin/Repair Instructions
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK1201458
Service Bulletin/Repair Instructions
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
IK0700112
Service Bulletin/Repair Instructions
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK0100051
Service Bulletin/Repair Instructions
Frame Rail Straightness Inspection Procedure
IK1500074
Service Bulletin/Repair Instructions
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
IK1600233
Service Bulletin/Repair Instructions
Cab Lean Concern
IK0800504
Service Bulletin/Repair Instructions
Repair Procedures for Vehicles Struck by Lightning
IK0800284
Service Bulletin/Repair Instructions
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
IK0800475
Service Bulletin/Repair Instructions
Radio Diagnostics and Information
IK1600258
Service Bulletin/Repair Instructions
Cleaning and Disinfecting Trucks and Buses
IK0800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK0400159
Service Bulletin/Repair Instructions
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
IK0800533
Service Bulletin/Repair Instructions
Key Codes and Key Cutting Information (Not for CV Series)
IK0700097
Service Bulletin/Repair Instructions
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK0700079
Service Bulletin/Repair Instructions
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
K1200716
Service Bulletin/Repair Instructions
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
IK0800503
Service Bulletin/Repair Instructions
ISB Starting System Diagnostics; Only models built with cummins ISB engines
IK0800460
Service Bulletin/Repair Instructions
Build to VIN Wiring Harnesses
IK0400077
Service Bulletin/Repair Instructions
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
IK0800564
Service Bulletin/Repair Instructions
Child Checkmate is not functioning correctly; Only buses with features 47EXC, 47EXD, 47EXE built from 4/18/16 to 5/15/17
4328530R1
Service Bulletin/Repair Instructions
Tool Instruction - BCM Programming Harness
IK4300001
Service Bulletin/Repair Instructions
Updating OnCommand Link with Accelerator
IK1200921
Service Bulletin/Repair Instructions
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
IK2700100
Service Bulletin/Repair Instructions
OnCommand EZ-Tech
IK2500511
Service Bulletin/Repair Instructions
Using Supplier Software to Check DTCs
IK0800554
Service Bulletin/Repair Instructions
Telematic Installation Guidelines; only Units with 500K Data Link
IK0800341
Service Bulletin/Repair Instructions
Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
IK0700096
Service Bulletin/Repair Instructions
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
IK0800546
Service Bulletin/Repair Instructions
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
IK2900030
Service Bulletin/Repair Instructions
Dealer EZ-Tech and Diagnostic Software Support Resource Center
IK1201363
Service Bulletin/Repair Instructions
CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
IK0800445
Service Bulletin/Repair Instructions
Controller Updates for 500k Baud; only vehicles with 500k baud data link
IK1201360
Service Bulletin/Repair Instructions
Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
IK2700090
Service Bulletin/Repair Instructions
OnCommand EZ-Tech Download Center
IK0500038
Service Bulletin/Repair Instructions
Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
IK0500058
Service Bulletin/Repair Instructions
Steering Fluids
IK1201248
Service Bulletin/Repair Instructions
Cooling System Flush Procedure
IK1200029
Service Bulletin/Repair Instructions
RADIATOR INTERNAL RESTRICTION AND FLUSH PROCEDURE
IK1201335
Service Bulletin/Repair Instructions
Oil Pan Removal and Installation Procedure
IK1201332
Service Bulletin/Repair Instructions
High-pressure turbocharger outlet blockage
IK-0500057
Service Bulletin/Repair Instructions
ALL HEAVY PLATFORM POWER STEERING FLUID PRODUCTION CHANGE
IK-1500051
Service Bulletin/Repair Instructions
IK1500051 - DAVCO FUEL PRO 382 TECHNICAL MANUAL, INSTALLATION, DIAGNOSTICS, AND SERVICE
IK-2600225
Service Bulletin/Repair Instructions
IK2600225 - 500K BAUD ENGINE MODULE PROGRAMMING
IK-0500056
Service Bulletin/Repair Instructions
NEW STEERING SHAFT HEX BOLT
IK0400144
Service Bulletin/Repair Instructions
Standard to Heavy Duty Brake Chamber Replacement
REC15504
Service Bulletin/Repair Instructions
A diaphragm in the spring brake chamber may not be seated fully into the pressure plate and may cause internal leakage in the chamber, resulting in the parking brake to not fully release and drag.
IK0800485
Service Bulletin/Repair Instructions
Cluster Software Update Instructions
IK0800463
Service Bulletin/Repair Instructions
HIGH OR SPIKING VOLTAGE ONLY WITH LEECE-NEVILLE ALTERNATOR USING REMOTE VOLTAGE SENSE
IK0800368
Service Bulletin/Repair Instructions
Electrical Chassis Harnesses
IK0800379
Service Bulletin/Repair Instructions
Front ABS Harness
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.