IK1201526
Service Bulletin/Repair Instructions
This document will guide the user through the parts and information related to A26B resonator removal and EGR cross-over tube installation.
Vehicle report
2026 INTERNATIONAL HV
Service bulletins
37 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1201518
Service Bulletin/Repair Instructions
Some low mileage S13 engines in HV and HX chassis may experience complaints of excess fan belt noise or chirping, and or belt edge fraying. This document will guide the user through troubleshooting and Installation of the required parts needed to correct the issue. NOTE: HX with engine serial number (ESN) 6008637 and BELOW will require the instalation of a new front engine lifting bracket and dual idler pulley bracket to correct these complaints. All other chassis will need to follow the diagnostic steps linked below to pinpoint the cause.
IK1201506
Service Bulletin/Repair Instructions
This document will guide the user through to inspect A26 turbochargers remanufactured by SRC between 05/01/2023 and 02/01/2025. SRC Turbochargers assembled with new compressor housings may have a defect that prevents the TCOT sensor (Part# 1845988C1, Sensor, Exhaust Gas Temp) from being installed correctly.
IK4300031
Service Bulletin/Repair Instructions
This document will provide information regarding certain approved S13 and T14 chemicals.
IK0800560
Service Bulletin/Repair Instructions
This document will guide the user through the changes of the dielectric grease/coatings used in certain areas on all International vehicles built after 1/8/2018. International's Electrical Engineering Team made this change to improve the longevity of the OEM coatings and to improve applications at the factory.
26101
Service Campaign
Certain International® trucks and IC BusTM CE Series buses may have out of date BCM programing that may cause erroneous fault codes after a vehicle sits for 2 or 3 days.
IK1201516
Service Bulletin/Repair Instructions
This document will guide the user through parts information and installation instructions for the IMP Isolation Kit.
IK1201514
Service Bulletin/Repair Instructions
This document provides instructions for sealing oil leakage past the flywheel bolt holes on S13 engines. Oil leaking from behind the crankshaft gear may exit through the flywheel bolt holes and is often misdiagnosed as a rear crankshaft seal leak. This condition is confirmed by oil-saturated flywheel bolts and visible oil pooling in the flywheel bolt holes behind the gear.
IK2800082
Service Bulletin/Repair Instructions
VIN and Incomplete Vehicle Document Label Replacement Procedure
IK2600255
Service Bulletin/Repair Instructions
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2700129
Service Bulletin/Repair Instructions
This article provides step-by-step guidance for troubleshooting issues with Techline Connect software.
IK0800691
Service Bulletin/Repair Instructions
This document is intended to inform dealers, technicians, parts departments, and customers of a change made to radio software to support updated Collision Mitigation, Lane Departure Warning (LDW), and Blind Spot Monitoring systems. If replacing the radios on the vehicles described below, the radio either needs to be built after a specific build date or have the software version verified/updated. If outdated radio software is used on these vehicles, the audible tones for these systems may not be heard by the driver. The applicable vehicles were all built with the correct radio. This iKNnow article only applies if replacing the radio for a service event in one of the vehicles listed below.
IK3100005
Emissions
This article will provide the calibration revision history for S13 Integrated EPA 2024 Powertrains.
IK1201505
Service Bulletin/Repair Instructions
This article is to walk through and assist the technician in diagnosing and repairing some of the known leaks around the S13 Integrated Powertrain.
IK2600090
Other
New CARB Idle Reduction Change Request
IK4300035
Service Bulletin/Repair Instructions
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK1300197
Service Bulletin/Repair Instructions
This document will guide the user through T14 Upper Transmission Harness replacement along with TOSS (Transmission Output Shaft Sensor) replacement on select, effected vehicles.
IK2600264
Service Bulletin/Repair Instructions
This document provides instructions for the programming changes that will be needed when performing an S13 engine swap.
IK2600047
Service Bulletin/Repair Instructions
Engine replacements for all International engines will need to follow this procedure.
IK1600272
Service Bulletin/Repair Instructions
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK2600279
Service Bulletin/Repair Instructions
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
IK0800677
Service Bulletin/Repair Instructions
This document is intended to provide supplemental information for concerns with brake light switches and pressure sensors used by the BCM and PIM module to determine if the operator of the vehicle is applying the service brakes. All S13 vehicles are equipped with BCM feature 597483 (BCM PROG, BRAKE SWITCH, Use With Brake Application Pressure Switch). 597483 uses a normally open brake pressure switch that closes with 2-6 psi of air pressure and a brake application pressure sensor. When the switch is closed or the pressure sensor reads higher than 4psi, the BCM considers the brakes applied and will broadcast that over the J1939 networks to other modules. The S13 also includes a redundant brake switch that is wired directly to the PIM. This switch is normally closed and opens with 2-6 psi of air pressure. If the S13 ECM believes the brakes are applied from one of these brake signals, it can reduce or completely cut throttle input.
IK0600030
Service Bulletin/Repair Instructions
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK0800689
Service Bulletin/Repair Instructions
In some instances, the driver's or passenger's door pod may become unresponsive, where it will not respond to any manual inputs from the driver or passenger. In some of these situations, it is possible for this symptom to be present without any fault codes becoming active. This article will guide the user through performing a hard reset of a door pod, which can restore the door pod to its operational condition, thereby avoiding the need for replacement. The steps in this article should be performed BEFORE diagnostics are completed for any active faults.
IK1201009
Service Bulletin/Repair Instructions
In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of humidity, an operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK0800688
Service Bulletin/Repair Instructions
This document is to notify the field of an issue with BCM that causes various electrical system concerns after the vehicle sits for 2-3 days. This can affect all LT, RH, MV, HV models, 2021MY and up HX, 2024MY and up CE Bus with BCM kernel version 752, 753, and 754. Vehicles built or updated with DLB between 6/1/25 and 11/4/25 are suspected of having these kernels installed on the BCM. The most common complaint is that the steering wheel switches do not function, which, depending on the vehicle model and options, can cause the bus door, pupil warning lights, radio controls, marker interrupt, and cruise control to stop working. Other complaints can include short circuit faults from multiple sensor circuits attached to the BCM setting at the same time, the vehicle will not go into gear, the headlights are stuck on, the brake lights are stuck on, or the parking brake alarm is sounding (horn chirping) with the parking brake set. As of 11/4/25, these symptoms can be resolved by updating the BCM to kernel 755 or later with DLB.
IK3400001
Service Bulletin/Repair Instructions
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Service Bulletin/Repair Instructions
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Service Bulletin/Repair Instructions
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Service Bulletin/Repair Instructions
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Service Bulletin/Repair Instructions
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0800684
Service Bulletin/Repair Instructions
Title: Erratic BCM and RPM Behavior with Kernel 747-752 Applies To: All MV, HV, HX with RPM modules
IK1201519
Service Bulletin/Repair Instructions
Title: Replacing the Crankshaft Gear on S13 Engines
IK0500054
Service Bulletin/Repair Instructions
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Service Bulletin/Repair Instructions
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK1201511
Service Bulletin/Repair Instructions
Title: Supplemental A26 MAF Fault Diagnostics Applies To: All A26 Engines
IK0300078
Service Bulletin/Repair Instructions
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.