Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1900198
Service Bulletin/Repair Instructions
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK0800560
Service Bulletin/Repair Instructions
This document will guide the user through the changes of the dielectric grease/coatings used in certain areas on all International vehicles built after 1/8/2018. International's Electrical Engineering Team made this change to improve the longevity of the OEM coatings and to improve applications at the factory.
26101
Service Campaign
Certain International® trucks and IC BusTM CE Series buses may have out of date BCM programing that may cause erroneous fault codes after a vehicle sits for 2 or 3 days.
IK2600297
Service Bulletin/Repair Instructions
This document enables technicians to: 1. Accurately identify International® A26B engine control systems. 2. Understand the programming requirements and system behavior. 3. Perform programming tasks independently without needing technical support.
IK2600298
Service Bulletin/Repair Instructions
This document enables technicians to: 1. Accurately identify International® A26A engine control systems. 2. Understand the programming intricacies related to these systems. 3. Perform programming tasks independently without needing technical support.
IK0600001
Service Bulletin/Repair Instructions
Some interaxle shafts (the driveshaft connecting 2 drive axles) utilize special phasing. This is by design to reduce torsional vibrations. See Dana/Spicer letter here & Meritor here.
IK1201526
Service Bulletin/Repair Instructions
This document will guide the user through the parts and information related to A26B resonator removal and EGR cross-over tube installation.
IK1500109
Service Bulletin/Repair Instructions
This document will guide the user through supplemental fuel system diagnostics on 2017 A26 ESN 4500000 - 4599999.
IK2600069
Service Bulletin/Repair Instructions
This document will guide the user through troubleshooting steps to submitting a case file for a horsepower request.
IK2600090
Other
New CARB Idle Reduction Change Request
IK4300035
Service Bulletin/Repair Instructions
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600255
Other
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK0800563
Service Bulletin/Repair Instructions
Feature code 0008TSJ for auto start stop is a feature that will allow you to preset values in the body controller to allow the truck to start when the battery voltage or engine oil temperature reaches the preset value. The engine will then run for a preset time after battery voltage is within programmed value (if the engine started for low voltage) or the engine will run until oil temperature reaches a programmed value (if the engine started for oil temperature).
IK2600047
Service Bulletin/Repair Instructions
Engine replacements for all International engines will need to follow this procedure.
IK1600272
Service Bulletin/Repair Instructions
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK2600279
Service Bulletin/Repair Instructions
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
IK1201009
Service Bulletin/Repair Instructions
In some geographic areas, ambient temperatures reaching below 40°F (4°C), including high levels of humidity, an operator may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK2600253
Service Bulletin/Repair Instructions
This document guides dealer technicians through the programming process for an A26a (2017-2021) engine swap (both NEU and new engines).
IK0600030
Service Bulletin/Repair Instructions
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK0800689
Service Bulletin/Repair Instructions
In some instances, the driver's or passenger's door pod may become unresponsive, where it will not respond to any manual inputs from the driver or passenger. In some of these situations, it is possible for this symptom to be present without any fault codes becoming active. This article will guide the user through performing a hard reset of a door pod, which can restore the door pod to its operational condition, thereby avoiding the need for replacement. The steps in this article should be performed BEFORE diagnostics are completed for any active faults.
IK1201463
Service Bulletin/Repair Instructions
The purpose of this article is to describe all aspects of the A26 Connecting Rod Replacement Repair Processes. To address an A26 connecting rod supplier quality spill, Navistar is streamlining quality repair strategies to help avoid customer disturbance. Navistar is implementing connecting rod replacements which results in less downtime and damage avoidance.
IK0800688
Service Bulletin/Repair Instructions
This document is to notify the field of an issue with BCM that causes various electrical system concerns after the vehicle sits for 2-3 days. This can affect all LT, RH, MV, HV models, 2021MY and up HX, 2024MY and up CE Bus with BCM kernel version 752, 753, and 754. Vehicles built or updated with DLB between 6/1/25 and 11/4/25 are suspected of having these kernels installed on the BCM. The most common complaint is that the steering wheel switches do not function, which, depending on the vehicle model and options, can cause the bus door, pupil warning lights, radio controls, marker interrupt, and cruise control to stop working. Other complaints can include short circuit faults from multiple sensor circuits attached to the BCM setting at the same time, the vehicle will not go into gear, the headlights are stuck on, the brake lights are stuck on, or the parking brake alarm is sounding (horn chirping) with the parking brake set. As of 11/4/25, these symptoms can be resolved by updating the BCM to kernel 755 or later with DLB.
IK1201527
Service Bulletin/Repair Instructions
This document will guide the user through diagnosing the fuel/soot mixture found in the EGR system.
IK3400001
Service Bulletin/Repair Instructions
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Service Bulletin/Repair Instructions
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Service Bulletin/Repair Instructions
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Service Bulletin/Repair Instructions
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK2600262
Service Bulletin/Repair Instructions
Title: Export Recalibration Process & Emissions Label - A26 Applies To: Service Manager, General Manager, Technicians.
IK1201501
Service Bulletin/Repair Instructions
Title: S13 Gear Housing Leak (By The Air Compressor) Applies To: S13 Integrated Powertrain LT RH HX
IK1200716
Service Bulletin/Repair Instructions
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK1201519
Service Bulletin/Repair Instructions
Title: Replacing the Crankshaft Gear on S13 Engines
IK1201509
Service Bulletin/Repair Instructions
Title: S13 New Power Steering Tube Support Brackets
IK0500054
Service Bulletin/Repair Instructions
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK1900299
Service Bulletin/Repair Instructions
Title: Parameters for 16UZL with 16VKW Applies To: Vehicles with both feature codes 16UZL and 16VKW
IK1201511
Service Bulletin/Repair Instructions
Title: Supplemental A26 MAF Fault Diagnostics Applies To: All A26 Engines
IK0300078
Service Bulletin/Repair Instructions
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK0800679
Service Bulletin/Repair Instructions
Title: Battery Disconnect Switch Replacement - Best Practices Applies To: All Models with Battery Disconnect Switch
IK0900156
Service Bulletin/Repair Instructions
Title: Connecting an Auxiliary APU to the S13 Coolant System
IK1400023
Service Bulletin/Repair Instructions
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0800351
Service Bulletin/Repair Instructions
This document is used to help guide through fault codes.
IK12101498
Service Bulletin/Repair Instructions
This article will call out those VINs that are equipped with the shim, and if and when the shim should be used as a field repair solution.
IK19000292
Service Bulletin/Repair Instructions
This document will guide the user on the available part kits for servicing A/C system in the event of severe failure.
IK0500021
Service Bulletin/Repair Instructions
This document will guide the user how to properly diagnose or repair a truck equipped with a Sheppard's steering gear with Auto Relief Plungers.
IK0800659
Service Bulletin/Repair Instructions
This document will guide the user through relocating the No-Idle system's voltage sense source from the battery to the interior sleeper PDM.
iK1200101
Service Bulletin/Repair Instructions
The purpose of this document is to guide a user to resolve fault code 285 & 286 for Cummins engines.
iK1500095
Service Bulletin/Repair Instructions
This document will provide the user with cleaning options and procedures for aluminum bright work parts that become stained or tarnished.
IK2600265
Service Bulletin/Repair Instructions
This document will guide the user on what to do when they receive a fault code after programming an ECM on A 26A engines
RC5000005
Service Bulletin/Repair Instructions
Update to International Preventative Maintenance
IK0400037
Service Bulletin/Repair Instructions
This document is to guide users to eliminate brake pedal rattle noise.
IK08000403
Service Bulletin/Repair Instructions
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
IK0800482
Service Bulletin/Repair Instructions
This document covers battery diagnostics, maintenance and storage requirement.
VER 23521
Service Bulletin/Repair Instructions
Certain International vehicles built with A26 engines does meet the emission requirements for J1939-Stationary Test
IK0800407
Service Bulletin/Repair Instructions
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
ik0800664
Service Bulletin/Repair Instructions
LT & RH aftertreatment PDM F2 fuse falling out or cracking.
IK1201406
Service Bulletin/Repair Instructions
A26 & S13 Fuel Gelling
IK0800664
Service Bulletin/Repair Instructions
Aftertreatment PDM F2 fuse falling out or cracking.
IK0800663
Service Bulletin/Repair Instructions
Corroded TPMS Receiver / Repeater Module Connectors; only models equipped with feature code 16VLS or 16VVM
IK1600260
Service Bulletin/Repair Instructions
Tire Pressure Monitoring system; Feature Codes 16VLS, 16VUY, 16VVA, 16VVM, or 16VUZ
IK1201476
Service Bulletin/Repair Instructions
Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
IK1300192
Service Bulletin/Repair Instructions
Endurant Plumbing Retrofit; only models built with endurant transmission built before 11/01/2023
IK0300010
Service Bulletin/Repair Instructions
Diagnosis of chassis wander complaints.
IK0400040
Service Bulletin/Repair Instructions
General Wheel Speed Sensor Troubleshooting
IKo800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1201391
Service Bulletin/Repair Instructions
Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
IK0800652
Service Bulletin/Repair Instructions
Fifth Wheel Unlock - Trailer Lamp Detection Calibration. Only models equipped with BCM feature code 597017
IK0700120
Service Bulletin/Repair Instructions
QLS Emergency Calibration Revert Process
IK1201482
Service Bulletin/Repair Instructions
Removal and Installation of the Air Cleaner Assembly Cover and Air Filters; All Engines and only HX and LT series trucks with feature code 012VCB or 012VBZ Air Cleaner Assembly
22501
Service Bulletin/Repair Instructions
This Emissions Recall applies to truck models for which, per agreement with EPA and CARB, Navistar, Inc. provided an emergency calibration for International® A26 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
IK1201466
Service Bulletin/Repair Instructions
New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
IK0800655
Service Bulletin/Repair Instructions
N2 telematics module not communicating with OCC systems. Only models built with feature codes 10ADT, 10AEY, 10AEU, 10AEZ, 10AGB, or 10AGC built from 04/04/2019 through 11/01/2022.
22502
Service Bulletin/Repair Instructions
Per agreement with EPA and CARB, Cummins, Inc. provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
IK1600265
Service Bulletin/Repair Instructions
Hood guide installation
IK1200101
Service Bulletin/Repair Instructions
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK0800554
Service Bulletin/Repair Instructions
Telematics installation guidelines - Only units with 500K data link
IK0800653
Service Bulletin/Repair Instructions
LT Truck headlight harness inspection and repair; only units built prior to 04/11/2022
IK1201473
Service Bulletin/Repair Instructions
Service Diagnostic Software (SDS) Template to enable Recall 22518 connecting rod knock detection software. Only vehicles with International A26 Engine
IK0700115
Service Bulletin/Repair Instructions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
IK1201472
Service Bulletin/Repair Instructions
Pico Scope CCOS (Crankcase Separator Test)
IK0900134
Service Bulletin/Repair Instructions
LT A26 Cold Side CAC Hose Rupture
22516
Service Bulletin/Repair Instructions
During high electrical demand, the cables that ground the batteries to the vehicle frame can carry the full system current and may result in excessively hot battery ground cables and in some cases, battery post separation. Only trucks equipped with Cummins engines, feature codes 0008GXK, 0008GHJ and 0008GWY (high output alternators 275 to 375 amp output), and feature codes 0016UZL and 0016VLN (no idle HVAC), or 008XDM and 008XLD (DC to AC power inverter).
IK1600261
Service Bulletin/Repair Instructions
Cab Components That Reduce Wheel End Vibration Complaints
IK0800605
Service Bulletin/Repair Instructions
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
IK0800607
Service Bulletin/Repair Instructions
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
Service Bulletin/Repair Instructions
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
Service Bulletin/Repair Instructions
PicoScope Test Resistance and Ohmmeter
IK0800611
Service Bulletin/Repair Instructions
PicoScope Wheel Speed Sensor Test
IK1201469
Service Bulletin/Repair Instructions
PicoScope Test One Channel RCT
22504
Service Bulletin/Repair Instructions
Under certain conditions, the Engine Control Module (ECM) programming may not detect when the Exhaust Gas Recirculation (EGR) flow exceeds the predetermined threshold resulting in not setting a fault code and activating the Malfunction Indicator Light (MIL). Only models equipped with International A26 engine.
22902
Service Bulletin/Repair Instructions
The Body Control Module (BCM) may have outdated software that could result in active Over The Air (OTA) programming to not fully complete and result in an inoperative Engine Control Module (ECM). Only models with International A26 engine and feature code 10ADT, 10AEK, 10AEU, 10AEY, 10AEZ, 10AGB, or 10AGC (Telematics Communications Module).
IK1900268
Service Bulletin/Repair Instructions
Side mounted cab extender fins that provide more flexibility during trailer contact.
IK1201440
Service Bulletin/Repair Instructions
International A26 engine fuel delivery pressure sensor and harness pigtail eliminated
IK1600131
Service Bulletin/Repair Instructions
Cab water leak trouble shooting tips
IK1600133
Service Bulletin/Repair Instructions
Textured surfaces on painted plastic bumpers, chassis side skirts, and fender extendtions
IK1600136
Service Bulletin/Repair Instructions
Primer recommendation for matching textured panels to smooth panels for field repairs
22507
Service Bulletin/Repair Instructions
The positive battery cable to the inverter may chafe on the side skirts and over time could result in an electrical short to ground; only trucks built 02/10/2017 thru 02/25/2022 with a power inverter installed by Navistarâs Truck Specialty Center
IK1600251
Service Bulletin/Repair Instructions
Water leaks past plastic vapor barrier sheet in the inner cavity of the cab entry door
IK0300068
Service Bulletin/Repair Instructions
LINK ride height smart valve operation and troubleshooting guide
IK1201460
Service Bulletin/Repair Instructions
Installing P/N 7104373C91 A26 Engine Sensor Harness
IK1201464
Service Bulletin/Repair Instructions
High Pressure Fuel Pump external leaks from weep hole. only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
IK0800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1000003
Service Bulletin/Repair Instructions
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK2600251
Service Bulletin/Repair Instructions
How to obtain As built parameter list
IK2600254
Service Bulletin/Repair Instructions
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
21901
Service Bulletin/Repair Instructions
The Environmental Protection Agency (EPA) and California Air Resources Board (CARB) have approved an emergency calibration to provide temporary relief from the global supply shortage of electrical components. When there is a communication fault in the DEF head unit / Quality Level Sensor (QLS) this temporary calibration will allow the vehicle to operate. The procedure in this document will include diagnosing the DEF head unit / QLS and if found to be defective will advise to install the temporary engine calibration if replacement parts are not available. Any vehicle that receives this calibration will be required to have it removed and a new QLS installed once parts become available, this will be managed through future communication.
IK1201299
Service Bulletin/Repair Instructions
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK1201458
Service Bulletin/Repair Instructions
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
21105
Service Bulletin/Repair Instructions
Certain International LT, HV and RH Series trucks may have the incorrect EGRV mounting bolts installed.
IK0800596
Service Bulletin/Repair Instructions
SiriusXM Reception Issues with Film Antenna in Hi-Rise Sleeper
IK0800594
Service Bulletin/Repair Instructions
Lane Departure Warning Alert Active with Turn Signals On; Only models equipped with Lane Departure Warning
IK0700112
Service Bulletin/Repair Instructions
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK0800595
Service Bulletin/Repair Instructions
Navistar N2 Telematics with Predictive Cruse Control; Only LT Series built after July 9th, 2020 with feature 12XBE
IK1201429
Service Bulletin/Repair Instructions
CPA BEAM RCT and Idle Test for A26 engine; only trucks equipped with International A26 engine
21505
Service Bulletin/Repair Instructions
The connecting rod bushing over time may develop cracks or lose chunks of material that could lead to connecting rod engine failure.
IK1600239
Service Bulletin/Repair Instructions
Sleeper bunk cabinet door latch installation and adjustment
21501R1
Service Bulletin/Repair Instructions
The battery ground cable may break at the frame connection resulting in loss of electrical power and unintended engine shut down without warning.
IK1900259
Service Bulletin/Repair Instructions
Day cab roof air deflector causing loud vibration noise at highway speed
IK0800593
Service Bulletin/Repair Instructions
Radio clock changes time automatically; Only vehicles built after March 2020 and excluding CV
21501
Service Bulletin/Repair Instructions
The battery ground cable may break at the frame connection resulting in loss of electrical power and unintended engine shut down without warning. Unintended engine shut down without warning may result in a vehicle being stalled on the side of the roadway which could increase the risk of a vehicle crash.
IK0100051
Service Bulletin/Repair Instructions
Frame Rail Straightness Inspection Procedure
IK0500038
Service Bulletin/Repair Instructions
Steering Shake, Shimmy, Shudder, Wobble, Steering Vibration; only models built with 14K weight rated axles or lower
IK2600128
Service Bulletin/Repair Instructions
A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters
IK1201454
Service Bulletin/Repair Instructions
This document will guide the user through what is normal appearance for a NEU A26 replacement engine assembly. Only models built with International A26 engines.
IK0800590
Service Bulletin/Repair Instructions
Programming Procedure for Center Panel Switch Packs
20905
Service Bulletin/Repair Instructions
Recalibrate Transmission Control Unit (TCU) software to improve Linear Clutch Actuator (LCA) performance and mitigate possible transmission service lamp and / or no gear engagement from neutral.
IK1201444
Service Bulletin/Repair Instructions
1 channel CPA RCT test for A26 or CV 6.6L; Only trucks built with International A26 or 6.6 engines
20506
Service Bulletin/Repair Instructions
Replacement of the Charge Air Cooler (CAC) outlet hose to prevent a potential increase of particulate matter emissions from a potential hose failure. Only LT Series built 3 December 2018 thru 11 October 2019 with 2018 and 2019 model year Cummins X15 engines.
IK1201453
Service Bulletin/Repair Instructions
7095496C3 EGR Bellows Heat Shield ID; only models equipped with A26 Engine
IK1500074
Service Bulletin/Repair Instructions
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
20115
Service Bulletin/Repair Instructions
Certain vehicles with a manual transmission may need the BCM to be updated for the over-the-air (OTA) programming to function.
IK0400163
Service Bulletin/Repair Instructions
Foot Valve Air Leak- Bendix ATR6 Traction Control Relay Valve Diagnostics; Only Models with Cummins X15 engine and feature code 04ECC air dryer
IK1600233
Service Bulletin/Repair Instructions
Cab Lean Concern
20105
Service Bulletin/Repair Instructions
The telematics module may not âcall home,â resulting in an inability to perform over-the-air programming.
IK1900261
Service Bulletin/Repair Instructions
Bluetooth Cannot Be Connected to Radio
IK0800504
Service Bulletin/Repair Instructions
Repair Procedures for Vehicles Struck by Lightning
IK0700102
Service Bulletin/Repair Instructions
DEF Coolant Line Leak Rear of Engine; only models with International A26 engine
IK0800284
Service Bulletin/Repair Instructions
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
IK4300009
Service Bulletin/Repair Instructions
This document will guide the user through the proper use of the A26 Misfire Detection Session to determine cylinder misfire count releted to the specific misfire DTCs.
20504
Service Bulletin/Repair Instructions
The connecting rod bushing over time may develop cracks or lose chunks of material which could lead to connecting rod engine failure. Connecting rod failure in some cases can result in engine shutdown with minimal warning. A stalled vehicle in or near the roadway can increase the risk of a vehicle crash.
IK0800475
Service Bulletin/Repair Instructions
Radio Diagnostics and Information
IK1600250
Service Bulletin/Repair Instructions
Horizon Cab Door Field Replacement and the Side Window Air Deflectors. NOTE: This article will only be applicable to cabs with the deflector mounted on the door pillar. If the cab has the deflector at the windshield, this article does not apply.
IK0800587
Service Bulletin/Repair Instructions
Lytx Video Monitoring Camera Inoperative; only LT series equipped with Lytx Camera System
IK1600258
Service Bulletin/Repair Instructions
Cleaning and Disinfecting Trucks and Buses
IK0800550
Service Bulletin/Repair Instructions
Multi Module Programming Information for In-Cab Modules
20101
Service Bulletin/Repair Instructions
Certain tandem axle International HX and LT Series trucks built between 20 August 2019 and 17 December 2019 with a lift axle may require the ABS Stability Control module to be updated to the latest parameters.
IK1201446
Service Bulletin/Repair Instructions
A26 Engine fault code SPN: 4364 FMI: 18 Supplemental Diagnostics; Only models built with A26 engine
IK0400159
Service Bulletin/Repair Instructions
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
IK0800585
Service Bulletin/Repair Instructions
Winter Fuel Or Additive Use Required Pop-Up Message
IK0800584
Service Bulletin/Repair Instructions
Auxiliary Engine Speed Control Cannot Hold Engine Speed When Using Steering Wheel Switches
IK1300174
Service Bulletin/Repair Instructions
Power Take Off (PTO) Programming on LT, RH and LoneStar Models with the Eaton Endurant Transmission; only models with feature code 13GZD, 13GYY, 13GYZ, 13GZA, 13GZB, or 13GZC
IK0400152
Service Bulletin/Repair Instructions
Windshield Replacement on trucks equipped with Lane Departure Cameras; Only RH, LT, and Medium duty with feature codes 008TTG, 0008TPU, 0008TTT, 0008TTU
IK1900257
Service Bulletin/Repair Instructions
Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector
IK1500085
Service Bulletin/Repair Instructions
LT / ProStar Fuel Tank Unable to Fill; only sleeper models
IK1600207
Service Bulletin/Repair Instructions
Wind noise at upper side of cab door due to door out of alignment
IK0700097
Service Bulletin/Repair Instructions
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK1201441
Service Bulletin/Repair Instructions
Identifying the Source of Oil Seen at the Lower Flywheel Housing Area. Only models equipped with Allison Transmission and International A26 or Cummins L9 engines
IK0800444
Service Bulletin/Repair Instructions
Driver Information Display (VIS/DID) screen fails to boot up.
IK0900136
Service Bulletin/Repair Instructions
LT Charge Air Cooler Hose Identification
IK1600245
Service Bulletin/Repair Instructions
Cab Door Latch Stuck, Door will not open
19516
Service Bulletin/Repair Instructions
Engine Control Module (ECM) calibration update to reduce a false positive Malfunction Indicator Lamp (MIL) for Oxides of Nitrogen (NOx) values when there is no malfunction with the NOx sensor or circuit.
IK1100032
Service Bulletin/Repair Instructions
LT, RH- Hydraulic Clutch Routing and Clipping
IK1300159
Service Bulletin/Repair Instructions
Fuller Advantage Series Transmission Power and Ground
19515
Service Bulletin/Repair Instructions
Replacement of the Charge Air Cooler (CAC) outlet hose to prevent a potential increase of particulate matter emissions from a potential hose failure.
19903
Service Bulletin/Repair Instructions
The battery discharge protection system may have an incorrect relay resulting in no battery discharge protection and no notification displayed on the instrument panel. Only models with feature code 08XJC (Battery Discharge Protection System).
IK0800551
Service Bulletin/Repair Instructions
LT RH HV MV Wire Terminal Information
19104
Service Bulletin/Repair Instructions
A deformation in the center post of the switch pack housing may cause one or more of the switches to become loose and / or pop out when depressed.
19109
Service Bulletin/Repair Instructions
Certain vehicles built 01 January 2019 thru 15 March 2019 with an International A26 engine may be susceptible to a Charge Air Cooler (CAC) hose failure.
IK1900249
Service Bulletin/Repair Instructions
LT CRX50 Refrigerator Diagnostics. Only models Equipped with the CRX50 Refrigerator
19110
Service Bulletin/Repair Instructions
Calibration update to protect the aftertreatment system when a Charge Air Cooler (CAC) hose fails. Only models equipped with International A26 engine
19106
Service Bulletin/Repair Instructions
When the differential lock switch is pressed, the differential lock WILL engage, but the LED on the switch may fast flash, indicating that the differential is NOT engaged. Only models built 01/14/2019 through 05/01/2019.
IK0700079
Service Bulletin/Repair Instructions
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
IK0200013
Service Bulletin/Repair Instructions
Suggested alignment target values when performing a vehicle axle alignment
IK1201433
Service Bulletin/Repair Instructions
Only models built with Cummins X15; Fault Code 7125
IK1500098
Service Bulletin/Repair Instructions
Installing the Racor GreenMax Primary Fuel Water Separator in Place of the Davco 382; Only LT and RH Series built with A26 engines
IK1600226
Service Bulletin/Repair Instructions
LT; Grille Chrome Plating Delamination
IK0800092
Service Bulletin/Repair Instructions
The First Check to make when Troubleshooting any Body Controller or ESC Issue
19501
Service Bulletin/Repair Instructions
The rear exhaust hanger bracket may crack and over time, may cause the forward hanger bracket to crack and in some cases may result in partial or full separation of the exhaust tail pipe from the vehicle; only models with 73 inch sleeper cab and feature code 07BKP or 07BKR (Exhaust system with horizontal aftertreatment devise and horizontal tailpipe mounted on right side).
K1200716
Service Bulletin/Repair Instructions
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
59310-004
Service Bulletin/Repair Instructions
Hendrickson Assembly Instructions; Transverse Torque Rods
IK0300047
Service Bulletin/Repair Instructions
Improved Bushings for Hendrickson Torque Rods