Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1900198
Service Bulletin/Repair Instructions
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK0800560
Service Bulletin/Repair Instructions
This document will guide the user through the changes of the dielectric grease/coatings used in certain areas on all International vehicles built after 1/8/2018. International's Electrical Engineering Team made this change to improve the longevity of the OEM coatings and to improve applications at the factory.
IK0300080
Service Bulletin/Repair Instructions
This article addresses chassis lean conditions on MV with IROS suspension. It does not include any diagnostics for body leans, such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean.
IK0800684
Service Bulletin/Repair Instructions
This document is to inform dealers, customers, and body builders/TEMs of a known BCM software issue with kernels 747 through 752. Units built after November of 2024 as well as older units that were updated with DLB between 11/5/2024 and 6/26/2025 with Remote Power Modules (RPM) modules, can experience loss of RPM functionality as well as other electrical system concerns. Kernel 753 was released to DLB on 6/26/2025 to address these concerns.
IK2600090
Other
New CARB Idle Reduction Change Request
IK4300035
Service Bulletin/Repair Instructions
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600255
Other
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2600047
Service Bulletin/Repair Instructions
Engine replacements for all International engines will need to follow this procedure.
IK1600272
Service Bulletin/Repair Instructions
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK2600279
Service Bulletin/Repair Instructions
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
IK1201009
Service Bulletin/Repair Instructions
In some geographic areas, ambient temperatures reaching below 40°F (4°C), including high levels of humidity, an operator may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK0600030
Service Bulletin/Repair Instructions
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK0800689
Service Bulletin/Repair Instructions
In some instances, the driver's or passenger's door pod may become unresponsive, where it will not respond to any manual inputs from the driver or passenger. In some of these situations, it is possible for this symptom to be present without any fault codes becoming active. This article will guide the user through performing a hard reset of a door pod, which can restore the door pod to its operational condition, thereby avoiding the need for replacement. The steps in this article should be performed BEFORE diagnostics are completed for any active faults.
IK0800688
Service Bulletin/Repair Instructions
This document is to notify the field of an issue with BCM that causes various electrical system concerns after the vehicle sits for 2-3 days. This can affect all LT, RH, MV, HV models, 2021MY and up HX, 2024MY and up CE Bus with BCM kernel version 752, 753, and 754. Vehicles built or updated with DLB between 6/1/25 and 11/4/25 are suspected of having these kernels installed on the BCM. The most common complaint is that the steering wheel switches do not function, which, depending on the vehicle model and options, can cause the bus door, pupil warning lights, radio controls, marker interrupt, and cruise control to stop working. Other complaints can include short circuit faults from multiple sensor circuits attached to the BCM setting at the same time, the vehicle will not go into gear, the headlights are stuck on, the brake lights are stuck on, or the parking brake alarm is sounding (horn chirping) with the parking brake set. As of 11/4/25, these symptoms can be resolved by updating the BCM to kernel 755 or later with DLB.
IK3400001
Service Bulletin/Repair Instructions
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Service Bulletin/Repair Instructions
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
25104
Service Campaign
MODELS INVOLVED: International® MV™ Series trucks
IK1900022
Service Bulletin/Repair Instructions
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Service Bulletin/Repair Instructions
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Service Bulletin/Repair Instructions
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0500054
Service Bulletin/Repair Instructions
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Service Bulletin/Repair Instructions
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK0300078
Service Bulletin/Repair Instructions
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK0800679
Service Bulletin/Repair Instructions
Title: Battery Disconnect Switch Replacement - Best Practices Applies To: All Models with Battery Disconnect Switch
IK1400023
Service Bulletin/Repair Instructions
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0900141
Service Bulletin/Repair Instructions
This document will guide a user to replace and reroute Charge Air Cooler (CAC) for vehicles built with the Cummins ISB and B6.7 engines.
iK1500095
Service Bulletin/Repair Instructions
This document will provide the user with cleaning options and procedures for aluminum bright work parts that become stained or tarnished.
IK0400037
Service Bulletin/Repair Instructions
This document is to guide users to eliminate brake pedal rattle noise.
IK08000403
Service Bulletin/Repair Instructions
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
IK0800482
Service Bulletin/Repair Instructions
This document covers battery diagnostics, maintenance and storage requirement.
IK0800407
Service Bulletin/Repair Instructions
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
IK0800503
Service Bulletin/Repair Instructions
Cummins ISB Starting system diagnostics.
IK0800351
Service Bulletin/Repair Instructions
J1939 Data Link Source Address Information
IK1600260
Service Bulletin/Repair Instructions
Tire Pressure Monitoring system; Feature Codes 16VLS, 16VUY, 16VVA, 16VVM, or 16VUZ
IK0300010
Service Bulletin/Repair Instructions
Diagnosis of chassis wander complaints.
IK0400040
Service Bulletin/Repair Instructions
General Wheel Speed Sensor Troubleshooting
IK1201457
Service Bulletin/Repair Instructions
Cummins B6.7 Grid Heater Relay
IK0800657
Service Bulletin/Repair Instructions
Starter kicks out after 1 second on MV and HV with Cummins L9 Engines
IKo800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK0700120
Service Bulletin/Repair Instructions
QLS Emergency Calibration Revert Process
IK1201480
Service Bulletin/Repair Instructions
Cummins B6.7 and L9 engines with codes 285 and 286
IK1200101
Service Bulletin/Repair Instructions
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK0800554
Service Bulletin/Repair Instructions
Telematics installation guidelines - Only units with 500K data link
IK0700115
Service Bulletin/Repair Instructions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
IK1201472
Service Bulletin/Repair Instructions
Pico Scope CCOS (Crankcase Separator Test)
IK0800605
Service Bulletin/Repair Instructions
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
IK0800607
Service Bulletin/Repair Instructions
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
Service Bulletin/Repair Instructions
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
Service Bulletin/Repair Instructions
PicoScope Test Resistance and Ohmmeter
IK0800611
Service Bulletin/Repair Instructions
PicoScope Wheel Speed Sensor Test
IK1201469
Service Bulletin/Repair Instructions
PicoScope Test One Channel RCT
IK1600145
Service Bulletin/Repair Instructions
Front cab mount bushings/insulators MV, HV, DuraStar, and WorkStar vehicles used in severe vocations
IK1600131
Service Bulletin/Repair Instructions
Cab water leak trouble shooting tips
IK1600251
Service Bulletin/Repair Instructions
Water leaks past plastic vapor barrier sheet in the inner cavity of the cab entry door
IK0800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1000003
Service Bulletin/Repair Instructions
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK1300086
Service Bulletin/Repair Instructions
Bendix Stability control - customer satisfaction performance improvement; Specific Emergency / Tanker applications only.
IK2600251
Service Bulletin/Repair Instructions
How to obtain As built parameter list
IK2600254
Service Bulletin/Repair Instructions
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
IK1201299
Service Bulletin/Repair Instructions
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK0800594
Service Bulletin/Repair Instructions
Lane Departure Warning Alert Active with Turn Signals On; Only models equipped with Lane Departure Warning
IK0700112
Service Bulletin/Repair Instructions
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK1900259
Service Bulletin/Repair Instructions
Day cab roof air deflector causing loud vibration noise at highway speed
IK0100051
Service Bulletin/Repair Instructions
Frame Rail Straightness Inspection Procedure
IK0800590
Service Bulletin/Repair Instructions
Programming Procedure for Center Panel Switch Packs
IK1500074
Service Bulletin/Repair Instructions
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
IK1600233
Service Bulletin/Repair Instructions
Cab Lean Concern
IK0800504
Service Bulletin/Repair Instructions
Repair Procedures for Vehicles Struck by Lightning
IK0800284
Service Bulletin/Repair Instructions
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
IK0800475
Service Bulletin/Repair Instructions
Radio Diagnostics and Information
IK1600250
Service Bulletin/Repair Instructions
Horizon Cab Door Field Replacement and the Side Window Air Deflectors. NOTE: This article will only be applicable to cabs with the deflector mounted on the door pillar. If the cab has the deflector at the windshield, this article does not apply.
IK1600259
Service Bulletin/Repair Instructions
Chrome Plated C-Loop Mirror Flat Glass Cracks
IK1600258
Service Bulletin/Repair Instructions
Cleaning and Disinfecting Trucks and Buses
IK0800550
Service Bulletin/Repair Instructions
Multi Module Programming Information for In-Cab Modules
IK1300185
Service Bulletin/Repair Instructions
Reduced ISB Engine Exhaust Brake Efficiency; Only vehicles with Allison 1000/2000 series transmissions
IK0800585
Service Bulletin/Repair Instructions
Winter Fuel Or Additive Use Required Pop-Up Message
IK0800584
Service Bulletin/Repair Instructions
Auxiliary Engine Speed Control Cannot Hold Engine Speed When Using Steering Wheel Switches
IK0400152
Service Bulletin/Repair Instructions
Windshield Replacement on trucks equipped with Lane Departure Cameras; Only RH, LT, and Medium duty with feature codes 008TTG, 0008TPU, 0008TTT, 0008TTU
IK1900257
Service Bulletin/Repair Instructions
Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector
IK1600255
Service Bulletin/Repair Instructions
Incorrect Turn Signal Cancellation Feature
IK1201398
Service Bulletin/Repair Instructions
ISB 6.7 Frequent Regeneration
IK1600207
Service Bulletin/Repair Instructions
Wind noise at upper side of cab door due to door out of alignment
IK0700097
Service Bulletin/Repair Instructions
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK1201441
Service Bulletin/Repair Instructions
Identifying the Source of Oil Seen at the Lower Flywheel Housing Area. Only models equipped with Allison Transmission and International A26 or Cummins L9 engines
IK1600245
Service Bulletin/Repair Instructions
Cab Door Latch Stuck, Door will not open
IK1201389
Service Bulletin/Repair Instructions
Cummins ISB Fan Drive Belt Chirp; Cummins ISB and Cummins B6.7
IK0800551
Service Bulletin/Repair Instructions
LT RH HV MV Wire Terminal Information
IK0400019
Service Bulletin/Repair Instructions
Air Powered (SAAR) Park Brake Troubleshooting (Service "P" Light Coming on). Only models with hydraulic brakes
IK0700079
Service Bulletin/Repair Instructions
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
IK1300176
Service Bulletin/Repair Instructions
This document will guide the user through repair direction to configure Transmission Control Module (TCM) to provide the correct transmission gear range monitor value to the Premium or Base Electronic Gauge Cluster (EGC).
IK0200013
Service Bulletin/Repair Instructions
Suggested alignment target values when performing a vehicle axle alignment
IK0800484
Service Bulletin/Repair Instructions
Voltage gauge drops on cold engine start-up; Only models built with Cummins ISB, B6.7, ISL, or L9 engines
19901
Service Bulletin/Repair Instructions
International; HV, HX, LT, MV, RH, LS, ProStar, TranStar, WorkStar; It is possible for an internal clutch finger to fail after Safety Recall 18518 was completed. This campaign is only for this failure mode and these conditions. Clutches that are replaced under this field campaign but do not exhibit this type of failure will have the warranty claim charged back to the servicing location.
IK0800092
Service Bulletin/Repair Instructions
The First Check to make when Troubleshooting any Body Controller or ESC Issue
K1200716
Service Bulletin/Repair Instructions
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
IK1300166
Service Bulletin/Repair Instructions
Power Take Off (PTO) Programming on Models with the Eaton Procision Transmission; Only with feature codes 13GBX, 13GBY, 13GYU, 13GYW, or 13WEP
IK1100033
Service Bulletin/Repair Instructions
ECA Clutch Departure
IK1100034
Service Bulletin/Repair Instructions
Heavy Duty Clutch May Not Acheive Full Departure
IK0400063
Service Bulletin/Repair Instructions
Brake pedal not returning and sticking slightly in the applied position
FSC18121
Service Bulletin/Repair Instructions
Certain MV Series and DuraStar models may have been built with an incorrect spacer for the left-side front axle spring resulting in a lean condition.
IK0800580
Service Bulletin/Repair Instructions
Heated Mirror Timer Programmable Parameter; only models with feature code 0597006 and built prior to January 23, 2019
CLIB-0035
Service Bulletin/Repair Instructions
Eaton Bulletin for their ECA Clutch issue referenced from IK1100033 and IK1100034
IK1300170
Service Bulletin/Repair Instructions
EATON ECA Clutches - Refer to CLIB0034
CLIB0034
Service Bulletin/Repair Instructions
EATON ECA Clutches - EATON document referenced from IK1300170
IK0800578
Service Bulletin/Repair Instructions
Body Builder Accessories Backfeeding Ignition Voltage
IK2600236
Service Bulletin/Repair Instructions
Cummins ECM Programming Procedure; Only models with EPA 2017 Cummins engines
IK0800114
Service Bulletin/Repair Instructions
Vehicle Speed ( VSS ) Output for Bodybuilders
IK0800130
Service Bulletin/Repair Instructions
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
IK0400077
Service Bulletin/Repair Instructions
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
IK0800445
Service Bulletin/Repair Instructions
Body Controller Updates for 500k Baud data link
4328530R1
Service Bulletin/Repair Instructions
Tool Instruction - BCM Programming Harness
IK0800575
Service Bulletin/Repair Instructions
City Horn Difficult to Active
IK0400158
Service Bulletin/Repair Instructions
Wabco OnGuard Software Update; Only 500k baud rate Units with Wabco OnGuard with Cummins Engines built before 9-24-2018.
FSC18112
Service Bulletin/Repair Instructions
Trucks equipped with a sound package that has Bluetooth capability may have been built without front speakers.
IK0900128
Service Bulletin/Repair Instructions
Identifying customer HVAC performance concerns / Evaporator Freeze up
IK1600247
Service Bulletin/Repair Instructions
Hood Gap and Alignment Tolerances
IK1500093
Service Bulletin/Repair Instructions
Cummins L9 EPA 17 Supplemental Fuel System Diagnostics - Racor Chassis Mounted Fuel Filter / Cummins fault 559
IK0800567
Service Bulletin/Repair Instructions
Starter power connection cleaning
18518
Service Bulletin/Repair Instructions
An internal component within the clutch assembly may fail, which in special circumstances could inhibit clutch disengagement resulting in the transmission to not achieve neutral when commanded by the driver.
IK0700096
Service Bulletin/Repair Instructions
Urea Quality Sensor (UQS) Boot Order