IK2600083
Service Bulletin/Repair Instructions
The new clusters in the post-2007 models store the mileage in memory. When replacing the cluster, follow these instructions to program the current vehicle mileage into the memory of the new cluster.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK2600083
The new clusters in the post-2007 models store the mileage in memory. When replacing the cluster, follow these instructions to program the current vehicle mileage into the memory of the new cluster.
IK1900198
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK1900240
This document will guide the user through the necessary steps to install the Pressure Transducer (PT) Switch Conversion Kit onto model year 2012 thru 2016 ProStar® and LoneStar®(Built prior to January 20,2015). This conversion is required to be performed during a A/C system failure in which the refrigerant system is opened.
IK2600300
This article equips technicians with the knowledge and steps needed to efficiently replace and program N9/N10 and N13 modules, while addressing potential baud rate incompatibility issues between the replacement module and the vehicle.
IK2600090
New CARB Idle Reduction Change Request
IK4300035
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600283
This document aims to enable technicians to: 1. Accurately identify N-series medium duty engine control systems. 2. Understand the programming intricacies related to these systems. 3. Autonomously execute programming tasks without needing technical support.
IK2600255
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2600047
Engine replacements for all International engines will need to follow this procedure.
IK2600284
This document aims to enable technicians to: 1. Accurately identify third generation MaxxForce medium duty engine control systems. 2. Understand the programming intricacies related to these systems. 3. Autonomously execute programming tasks without needing technical support.
IK1600272
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK2600279
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
IK1201009
In some geographic areas, ambient temperatures reaching below 40°F (4°C), including high levels of humidity, an operator may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK1201252
This document describes the process for utilizing the CPA High Pressure Fuel Pump (HPFP) Test
IK0600030
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK3400001
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0500054
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK0300078
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK1400023
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0400037
This document is to guide users to eliminate brake pedal rattle noise.
IK08000403
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
IK0800482
This document covers battery diagnostics, maintenance and storage requirement.
IK0200013
Suggested alignment target values when performing a vehicle axle alignment.
IK0800407
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
IK0800351
J1939 Data Link Source Address Information
IK1201476
Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
IK0300010
Diagnosis of chassis wander complaints.
IK0400040
General Wheel Speed Sensor Troubleshooting
23512
Certain International® N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturerâs Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
IKo800080
J1939 Data Link Troubleshooting
IK1201391
Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
IK1201466
New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
IK1200101
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK1201237
Turbocharger oil supply tube retrofit; only models with 2010 emissions MaxxForce 11 and 13 engines and N13 engines
IK1201472
Pico Scope CCOS (Crankcase Separator Test)
IK0800605
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
IK0800607
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
PicoScope Test Resistance and Ohmmeter
IK0800611
PicoScope Wheel Speed Sensor Test
IK1201469
PicoScope Test One Channel RCT
IK1600133
Textured surfaces on painted plastic bumpers, chassis side skirts, and fender extendtions
IK1600136
Primer recommendation for matching textured panels to smooth panels for field repairs
IK1600131
Cab water leak troubleshooting tips; HX with steel cab only
IK2600052
Calculating pulses per mile (speedometer setting); only models equipped with International engines
IK1201464
High Pressure Fuel Pump external leaks from weep hole. only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
IK0800080
J1939 Data Link Troubleshooting
IK1000003
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK2600251
How to obtain As built parameter list
IK1201299
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK1201458
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
21504
This VER will involve reviewing diagnostic codes, inspection of the EGR valve / EGR System, and may include EGR valve replacement. Only models with 2012 model year MaxxForce 13 engines and are registered in California or have California apportioned registration.
IK0700112
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK1900259
Day cab roof air deflector causing loud vibration noise at highway speed
IK0500038
Steering Shake, Shimmy, Shudder, Wobble, Steering Vibration; only models built with 14K weight rated axles or lower
IK2600128
A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters
IK1500074
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
IK1600233
Cab Lean Concern
IK0800504
Repair Procedures for Vehicles Struck by Lightning
IK0800284
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
IK0800475
Radio Diagnostics and Information
IK1600258
Cleaning and Disinfecting Trucks and Buses
IK0400159
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
IK0800364
Stand Alone Real Time (SART) Module Diagnostics. Only 2010 and later models equipped with MaxxForce® 11/13/15 engines or N13 with feature 0508051
IK1500085
LT / ProStar Fuel Tank Unable to Fill; only sleeper models
IK1600207
Wind noise at upper side of cab door due to door out of alignment
IK0700097
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK0800444
Driver Information Display (VIS/DID) screen fails to boot up.
IK0700079
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
IK0800092
The First Check to make when Troubleshooting any Body Controller or ESC Issue
K1200716
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
IK0800085
ProStar Electrical System Load Shed Feature 08XEV
IK0800503
ISB Starting System Diagnostics; Only models built with cummins ISB engines
IK0800059
Brake Lights Staying On
IK0800017
Programing New Key Fobs
59310-004
Hendrickson Assembly Instructions; Transverse Torque Rods
IK0800579
Xantrex 1200W Power Inverter Information; only models with feature code 0008XLD
IK0800510
Cooper Bussmann Inverter Information/Diagnostics; only models with feature code 0008XDM or 0008XDN and built after 05/12/2014
IK0800130
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
IK0800460
Build to VIN Wiring Harnesses
IK0300047
Improved Bushings for Hendrickson Torque Rods
IK0400077
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
4328530R1
Tool Instruction - BCM Programming Harness
IK1900172
Espar Airtronic Heater Diagnostic Guide; only models with Feature code 16VTV
IK1900168
Fifth Wheel Jaw Unlock; only models with Feature 595BAW or 597017 - electronic Jaw release
IK1201119
Cummins ISX SCR System wiring
IK0800538
SCR Aftertreatment Harness Replacement
IK0900127
Heater Hose Chafing; Only models built with N13 engine
IK0800326
Auto Start Stop Troubleshooting; only ProStar with feature code 0008TSJ
Rec17V-792_2017-
The fire extinguishers may become clogged or require excessive force to activate. In certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. Only equipped with Kidde model FC5 and FC10 fire extinguishers identified by International part numbers 1696423C2 and 1696423C3 and installed post production at Navistar?s Truck Sales Processing Center (TSPC).
IK4300001
Updating OnCommand Link with Accelerator
IK1200921
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
IK2700100
OnCommand EZ-Tech
IK2500511
Using Supplier Software to Check DTCs
IK0800341
Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
IK0800508
SCR Chassis Overlay Instruction
IK0700096
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
IK0800546
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
IK2900030
Dealer EZ-Tech and Diagnostic Software Support Resource Center
IK1201363
CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
IK1201360
Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
IK2700090
OnCommand EZ-Tech Download Center
IK0800333
Parasitic Battery Load and Predelivery Storage Recommendations
REC16509
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification and proper diagnosis.
IK0800537
DM harness inspection; Only with Steering Column feature code 05710
IK0500058
Steering Fluids
IK1201102
Low Coolant Switch Diagnostics; only with Cummins ISX
IK1201248
Cooling System Flush Procedure
IK1600183
Offensive Odors Inside Cabin
IK1600116
Mirror / Map Light / Visor LED Lighting Up when CB MIC is Keyed
REC16508
The battery terminal mounted cube fuse connection that supplies power to the cab may possibly break, resulting in loss of power to the cab.
IK0800374
To Get A Helios Capture; All 1939 and 1708 multiplexed trucks only
IK1600222
POWER WINDOW BINDING
IK1100031A
HARD TO CRANK CONDITION ON VEHICLES WITH HYDRAULIC CLUTCH LINKAGE AND SOLO CLUTCH
IK0400140
AIR COMPRESSOR RETROFIT FOR PROSTAR MODELS EQUIPPED WITH 2010 EPA AND NEWER MAXXFORCE 11 & 13 ENGINES AND FEATURE CODE 04SPL
IK0400057
NEW BRAKE LIGHT OPERATION; PROSTAR AND LONESTAR WITH AIR BRAKES
REC16507
THE ON BOARD DIAGNOSTIC (OBD) DATA STORED FOR PURPOSES OF DEFINING REQUIRED MAINTENANCE OR REPAIR MAY BE INADVERTENTLY LOST WITHOUT NOTICE TO THE OPERATOR.
IK1200029
RADIATOR INTERNAL RESTRICTION AND FLUSH PROCEDURE
IK1600201
PROSTAR SLEEPER CAB STRUT NOISE OR AIR LEAKS
IK1900223
Air Conditioning Electrical Diagnostics
IK1900228
2010 and Newer Vehicle Air Conditioning Diagnostics (Start Here)
IK0800441
Adding an Electronic Trailer Brake Controller
TT7829EN
Tech Tip to aid technicians in the efficient removal and installation of a TC10 transmission
IK0400088
Brake Single Hot Wheel End Service Procedure
IK-1201314
PERFORMING RELATIVE COMPRESSION TEST AND MISFIRE TEST WITH CPA TOOL
IK-1200915
MISFIRE DIAGNOSTICS IBB; SPN132(X) - FMI 31
IK-1201320
IK1201320 - EGR SLOW RESPONSE DIAGNOSTICS; 2659 - 10
IK-1500051
IK1500051 - DAVCO FUEL PRO 382 TECHNICAL MANUAL, INSTALLATION, DIAGNOSTICS, AND SERVICE
IK-1201253
IK1201253 - EXHAUST MANIFOLD SERVICE PROCEDURES
IK-1201326
IK1201326 - SERVICE PARTS DAMAGED NEW TURBOCHARGER OIL SUPPLY TUBE
IK-1201157
IK1201157 - UPDATE FOR EXCESSIVE LUBRICATION OIL CONSUMPTION
IK1201323
ISX15 Aftertreatment Fuel Injector Replacement
15517
Accelerator pedal sensor (APS) recalibration
IK0600018
Driveline Replacement - JB Hunt only
IK0800427
Active Faults During Load Shed
IK0900105
Retrofiting a Horton VMaster(Stratis) fan drive to Horton 2spd air operated fan drive on N13 or MaxxForce 13 engines
IK1900245
ESPAR D5 Hydronic Diagnostic Guide
IK0800414
Windows Stop Randomly or are Inoperative, Power Door Locks are inoperative
IK1900235
No-Idle HVAC Operational Check - STARTING POINT
IK1900239
Symptom 5: NoIdle HVAC Blows Warm Air
REC15V-607
The fifth wheel and its locking mechanism may be susceptible to cumulative damage resulting in the fifth wheel lock to function improperly or a failure of the locking mechanism to properly engage
IK1900080
VORAD VS-400 Side Display Inop
IK0700072
ISX Setting 3556-18 (FC3167), 5298-18 (FC1691), or 3482-2 (FC1925) Caused by Missing AFI Poppet
121602
Change in Seat Belt Manufacturer - Inspection and Replacements
IK1100031
Hard to Crank Condition with Hydraulic Clutch Linkage and Solo Clutch
IK0400144
Standard to Heavy Duty Brake Chamber Replacement
IK1600219
ESPAR Preventative Maintenance / Inpection
IK1900234
Symptom 1: No Idle HVAC Cools but Operates Incorrectly
IK1900237
Symptom 3: NoIdle HVAC Inoperative
IK1600023
Mirror Repair Procedures and Replacement Parts Availability
IK0900118
MaxxPower Condenser Fan Diagnostics with the MaxxPower No-idle System (16UZL)
IK1201096
LT EGR Core Removal and Insertion with MaxxForce 11, 13, and N13 engines
IK1900158
Dash Cluster Lamp Operation, Functions and Regeneration Instructions, With International engines
IK1900212
Front Blower Motor Runs Breifly At Initial Power Up
REC15509
A jump start or electrical load dump event could result in an overvoltage condition of the cab Linear Power Module (LPM). The overvoltage condition could eventually cause overheating of the LPM circuit board.
IK0400125
Rear S Cam Tube / Bracket part update
IK0400146
N13, MaxxForce 11, 13 engine Two Cylinder Air Compressor Testing
IK0800296
HVAC faults 520211 and 520465
IK1100005
Eaton Clutch Information
IK1900218
ESPAR AirTronic Low Run Time.
IK0700032
DPF Snap Accel Test - Quick Test to All vehicles with DPFs
IK-0800465
NAVISTAR: STEERING WHEEL WILL NOT HAVE SHIFT CONTROLS DUE TO PHOENIX SHIFTER BEING PROGRAMMED TO LOOK FOR STEERING WHEEL MOUNTED SHIFT CONTROLS AND IF AN ERROR IS DETECTED, A FAULT WILL BE SET. MODEL PROSTAR. *PE UPDATED 9/14/15 *CN
IK1600217
Grille/Bug Screen Rubbing Against A/C Condenser
MIN15106
An incorrect terminal may have been installed on harness part number 4047811C91. This terminal does not allow the harness to be installed without modifying the harness.
IK1900225
Air Conditioning Mechanical Pressures Diagnostics
IK0900110
Coolant odor in cab with rear HVAC; equipped with Feature 0595BJN or 0595BWZ
IK1500005
Dual Fuel Tank Transfer Pump System With Two Wire Pump Troubleshooting; equipped with feature 595192 built after 08/19/2002
IK1500035
Dual Fuel Tank Transfer Pump Troubleshooting on Post-2007 NGV and ProStar
IK0400104
04SPL, MCAC 476, Yoosung, Compressor - Service Information
IK1500057
Davco Fuel Filter Replacements Recommendation for Maxx Force 11 and 13, 2010 Engines
IK1900207
HVAC Diagnostic Information
IK1201118
Charge Air Cooler Outlet Temperature Sensor Damaged; equipped with N13, MaxxForce 11, 13 engines
IK1900236
Symptom 2: No-Idle HVAC Fault Codes
IK1900238
Symptom 4: No-Idle HVAC Digital Display Inoperative
IK1100025
CLUTCH SERVICE INFORMATION; EQUIPPED WITH HYDRAULIC CLUTCH SYSTEMS
IK0400141
Trailer ABS In-Dash Lamp Stays On After A Trailer Has Been Disconnected; only with An In-Dash Trailer ABS Warning Lamp feature
IK0800485
Cluster Software Update Instructions
IK1900226
Air Conditioning Control Head Diagnostics
IK0800119
ProStar and NHPV with Suspension Dump feature code 595ACA or 595BBC
IK1900233
No Idle HVAC Solution Parts Identification; only with feature 16UZL No Idle HVAC
IK1600210
Compressor Relay and Power Harness Upgrade; only with feature 16UZL No Idle HVAC
AFC 14906
Clutch Switch Inspection and Replacement.
IK1900230
Rear A/C Blows Warm Air
IK1900231
Rear A/C Control Panel Inoperative
IK1900232
Sleeper Fan and Sleeper TEMP Switch Inoperative
MIN-14121
NAVISTAR: DIESEL EXHAUST FLUID (DEF) WILL FREEZE INSIDE PURGE PUMP DUE TO AFTERTREATMENT CONTROL MODULE (ACM) NOT RECEIVING BATTERY POWER (BATTERY DISCONNECT SWITCH), AND PURGE CYCLE FAILS TO COMPLETE, AFTER IGNITION KEY IS OFF. MODEL PROSTAR, WORKSTAR. *PE
MIN14121
VEHICLES EQUIPPED WITH A BATTERY DISCONNECT SWITCH MIGHT ENCOUNTER AN ISSUE WHERE THE DIESEL EXHAUST FLUID (DEF) FREEZES INSIDE THE PURGE PUMP DUE TO THE AFTERTREATMENT CONTROL MODULE (ACM) NOT RECEIVING BATTERY POWER
AFC14904
TO ENSURE ENGINETORQUE PARAMETERS AR PROPERLY MATCHED TO SPECIFIED DRIVELINE; WITH ISX ENGINE AND FEATURE 06DDN DRIVELINES
IK0900087
TEMPERATURE RADIATOR DIAGNOSTICS
MIN-14119
NAVISTAR: WHEN BODY CONTROLLER FAILS TO RECOGNIZE SWITCH INPUT AFTER BRAKE PEDAL IS DEPRESSED, THE ENGINE BRAKE BECOMES INOPERATIVE. MODEL PROSTAR. *PE
IK0800499
BATTERY DISCHARGE DURING EXTENDED STORAGE; PROSTAR EQUIPPED WITH FEATURE 0008WEN
IK-0900094
IK: REPAIR INFORMATION REGARDING THE MISSING OR LOOSE BOLT ATTACHING HORTON STRATIS ANTI ROTATION BRACKET (ARB) TO ENGINE. MODEL PROSTAR, WORKSTAR, LONESTAR. NO YEARS LISTED. *PE UPDATED 6/27/2014 *JS UPDATED 11/7/14. *PE UPDATED 1/30/15. *PE
IK-0800497
INTERNATIONAL: ENGINE BRAKE FAILS. NOTHING HAPPENS WHEN SWITCH FOR ENGINE BRAKE IN STEERING WHEEL IS PRESSED. VERIFY BODY CONTROLLER IS NOT RECEIVING INPUT FROM STEERING WHEEL SWITCH AND SWITCH INPUT CIRCUIT IS MISSING. MODEL PROSTAR. *PE
IK1600202
COWL TRAY SEAL; ONLY BUILT PRIOR TO 11/11/2013
IK1900220
GEOTAB WITH WYE CABLE INSTALLATION
IK0800463
HIGH OR SPIKING VOLTAGE ONLY WITH LEECE-NEVILLE ALTERNATOR USING REMOTE VOLTAGE SENSE
IK1600208
Air Cleaner Contact with the EGR Crossover Tube; With Cummins ISX engine only
IK0400133
Collision Avoidance Wingman FLR-10 to FLR 20 Retrofit
IK1201148
ISX15 CM2350 X101 Rod Bearing Campaign
IK-1100031
INTERNATIONAL: TRUCK HARD TO CRANK DUE TO CLUTCH BEARING CONTACTING CLUTCH BRAKE PRIOR TO CLUTCH RELEASE PEDAL PASSING MAGNETIC CLUTCH SAFETY SWITCH, ON SOME TRUCKS, CLOSING SWITCH ALLOWING TRUCK TO CRANK. MODEL PROSTAR, LONESTAR. *PE UPDATED 02/11/2014 *JS UPDATED 08/04/2014 *JS
IK0800185
Wipers and Aftertreatment Lights Inop on Post 2007 Trucks with Body Controller
IK1900015
Activate HVAC Front Blower Message In Dash Message center; with Sleeper cab only
IK-1201039
INTERNATIONAL: THERE ARE ISSUES OF MISSING COMPLETE ENGINE AIR SUPPLY LINE AND ALSO MISSING T FITTING WITH 1/4" AIR LINE TO AFTERTREATMENT PURGE AIR VALVE. *PE UPDATED 08/04/2014 *JS
IK1201039
Aftertreatment Purge Air Valve Air Supply Line Routing for both Cummins ISX SCR and N13 SCR Engines
IK1900019
Sleeper HVAC blower will not run on high with engine off; with Sleeper cab only
IK1300016
New Synthetic Oil for Eaton and Spicer Transmissions; only with Eaton or Spicer transmissions
REC14508
The mounting bolts that fasten the air disc brake caliper to the caliper anchor plate may have not been tightened to their specified torque; only with air disc brake feature codes 04WEY, 04WEZ, or 04WZK.
IK1300021
Transmission Keeps Shifting and Display Keeps Flashing After Ignition is Turned Off; only with Freedom Line Transmission
IK1300029
Roll Pins Backing Out of Bell Crank; Only with manual transmission
IK0900030
In Chassis Cleaning Procedure for Cooling Package in All Models with MaxxForce 11, 13 Engines
IK0800478
Headlight Condensation or Frost; excludes sealed beam headlights such as on WorkStar, Paystar and 9900i)
REC13517
During vehicle operation, the rear chassis skirt upper horizontal support S-bracket may contact the fuel tanks during frame twist, and it is possible for the bracket to wear a hole in the top of the fuel tank, which may result in a fuel leak.
IK1100004
Clutch Linkage Rattle
IK1100020
ZF Sachs Twin XTend clutch; only Vehicles with heavy-duty ZF Sachs Twin XTend Clutch
IK1600034
Rubbing Between Front and Rear Skirts on ProStar
IK1600049
ProStar Side Skirt Paint Mismatch
IK1600062
Push-in Trim Fasteners Popping out or Missing
IK1600063
Sleeper Curtain Getting Sucked into HVAC Duct
IK1600064
No Idle Curtains Missing Velcro; only models with feature 16UZL - No Idle HVAC
IK1600065
Sleeper Buzz, Squeak, Rattle
IK1600066
Drawer Rattle
IK1600067
Work Surface Rattle
IK1600095
Work Surface Latch Jammed - Replacement
IK0400033
Automatic Traction Control (ATC) Tire Size Compatibility; only with feature 04AZD and 04AZJ Bendix ATC
IK0800483
Steering Column Harness Rub
IK1600002
ProStar Air Deflector Mounting Procedure (Rattling Noise from Air Deflector or Bulging Between Fasteners)
REC14506
The axle shafts may not be of sufficient length to fully engage into the side gears of the rear axle differential and may result in axle shaft spline failure.
IK0800442
Auxiliary Battery Box Cover Difficult to Remove; Only vehicles with Feature Code 0008XGG (auxilary battery box)
IK1200940
SCR Fluid Filter Replacement; only with Cummins ISX or Navistar N13 Diesel Exhaust Fluid System
IK0700065
Ordering SCR Aftertreatment Parts for Vehicles With Navistar Engines
IK0700071
Ordering SCR Aftertreatment Parts for Vehicles Powered by Cummins Engines
IK1500002
Fuel Level Not Equal Between Tanks on Dual Draw Dual Return Dual Tank Systems.
IK0800014
City Horn Blows When Driver Shuts off Truck and Walks Away; only equipped with with ESC or Body Controller
IK0800056
Retrieving Fault Codes Through the Cluster Doesn?t Work
IK0800196
Asterisk in Lower Right Quadrant of Dash Display
IK1200271
Remote Throttle Control Options for Vehicles with ESC?s or Body Controllers and International Engines
IK0800352
Body Controller/ESC Software Updates
AFC13918
Electronic Control Module (ECM) and Aftertreatment Control Module (ACM) Recalibration and Aftertreatment Fuel Line 1 Replacement
IK0700002
Proper Exhaust Shield Orientation
REC13514
On vehicles with the electronic jaw release system, the airlines at the isolation/vent valve may not be oriented correctly to the valve ports at the time of assembly; only models built 20 February 2008 thru 29 July 2013 with feature code 0595BAW or 0595BAY.
IK-0800427
INTERNATIONAL: THERE ARE CODE FAULTS, CAUSED BY LOAD SHEDDING, LOADED IN OTHER MODULES AND UNIT GOES INTO LOAD SHED AND FAILS TO HAVE POWER IN SWITCHES. MODEL PROSTAR, LONESTAR. NO YEARS LISTED. *PE
REC13503
Certain 2010, 2011, and 2012 model year MaxxForce® 11 engines do not meet EPA emissions requirements.
IK0800139
Remote Engine Speed Control Module (RESCM) Troubleshooting; Only trucks equipped with RESCM
IK0800411
Body Controller Resource Center
AFC13901
ECM Recalibration to provide engine protection against an increase in engine RPM while vehicle is idling (only in a parked state or if vehicle is not moving); Only models equipped with MaxxForce 13 engine. Retired
IK0800412
Headlight Operation and Troubleshooting; only Post 2007 Vehicles Built with a Body Controller
IK-0800326
INTERNATIONAL: ON SOME TRUCKS, AN AUTO START STOP FEATURE CODE 0008TSJ, ALLOWS PRESET VALUES IN BODY CONTROLLER, THAT ALLOW TRUCK TO START WHEN BATTERY VOLTAGE OR ENGINE OIL TEMPERATURE REACHES PRESET VALUE. MODEL PROSTAR. NO YEARS LISTED. *PE
IK0800172
NAVISTAR: VARIOUS TYPES OF VEHICLES INCLUDING LONESTAR, PROSTAR, 8600, AND 7600 VEHICLES WILL NEED AN OPERATION TO IMPROVE THE CAB CIRCUIT GROUNDS. 7/17/15 *TA
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.