IK2600083
Service Bulletin/Repair Instructions
The new clusters in the post-2007 models store the mileage in memory. When replacing the cluster, follow these instructions to program the current vehicle mileage into the memory of the new cluster.
Vehicle report
2016 INTERNATIONAL PROSTAR
Service bulletins
172 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IK1900198
Service Bulletin/Repair Instructions
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL w/ Safety Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. • The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
IK1900240
Service Bulletin/Repair Instructions
This document will guide the user through the necessary steps to install the Pressure Transducer (PT) Switch Conversion Kit onto model year 2012 thru 2016 ProStar® and LoneStar®(Built prior to January 20,2015). This conversion is required to be performed during a A/C system failure in which the refrigerant system is opened.
IK2600300
Service Bulletin/Repair Instructions
This article equips technicians with the knowledge and steps needed to efficiently replace and program N9/N10 and N13 modules, while addressing potential baud rate incompatibility issues between the replacement module and the vehicle.
IK2600090
Other
New CARB Idle Reduction Change Request
IK4300035
Service Bulletin/Repair Instructions
This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files. It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
IK2600283
Service Bulletin/Repair Instructions
This document aims to enable technicians to: 1. Accurately identify N-series medium duty engine control systems. 2. Understand the programming intricacies related to these systems. 3. Autonomously execute programming tasks without needing technical support.
IK2600255
Other
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature. Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
IK2600047
Service Bulletin/Repair Instructions
Engine replacements for all International engines will need to follow this procedure.
IK2600284
Service Bulletin/Repair Instructions
This document aims to enable technicians to: 1. Accurately identify third generation MaxxForce medium duty engine control systems. 2. Understand the programming intricacies related to these systems. 3. Autonomously execute programming tasks without needing technical support.
IK1600272
Service Bulletin/Repair Instructions
This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and windshields using an ultrasonic sound detector.
IK2600279
Service Bulletin/Repair Instructions
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
IK1201009
Service Bulletin/Repair Instructions
In some geographic areas, ambient temperatures reaching below 40°F (4°C), including high levels of humidity, an operator may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
IK1201252
Service Bulletin/Repair Instructions
This document describes the process for utilizing the CPA High Pressure Fuel Pump (HPFP) Test
IK0600030
Service Bulletin/Repair Instructions
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes. (Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
IK3400001
Service Bulletin/Repair Instructions
Title: Service Portal iKNow Feedback Case Types Applies To: All
IK1400005
Service Bulletin/Repair Instructions
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
IK1900022
Service Bulletin/Repair Instructions
Title: A/C Refrigerant and Oil Capacities Applies To: All current models
IK0900157
Service Bulletin/Repair Instructions
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
IK1200716
Service Bulletin/Repair Instructions
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
IK0500054
Service Bulletin/Repair Instructions
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
IK2600069
Service Bulletin/Repair Instructions
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
IK0300078
Service Bulletin/Repair Instructions
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles. The information applies to diesel, gas, and electric vehicles.
IK1400023
Service Bulletin/Repair Instructions
This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
IK0400037
Service Bulletin/Repair Instructions
This document is to guide users to eliminate brake pedal rattle noise.
IK08000403
Service Bulletin/Repair Instructions
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
IK0800482
Service Bulletin/Repair Instructions
This document covers battery diagnostics, maintenance and storage requirement.
IK0200013
Service Bulletin/Repair Instructions
Suggested alignment target values when performing a vehicle axle alignment.
IK0800407
Service Bulletin/Repair Instructions
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
IK0800351
Service Bulletin/Repair Instructions
J1939 Data Link Source Address Information
IK1201476
Service Bulletin/Repair Instructions
Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
IK0300010
Service Bulletin/Repair Instructions
Diagnosis of chassis wander complaints.
IK0400040
Service Bulletin/Repair Instructions
General Wheel Speed Sensor Troubleshooting
23512
Service Bulletin/Repair Instructions
Certain International® N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturerâs Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
IKo800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1201391
Service Bulletin/Repair Instructions
Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
IK1201466
Service Bulletin/Repair Instructions
New air compressor incorporates an oil feed dowel O-ring. Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
IK1200101
Service Bulletin/Repair Instructions
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
IK0700115
Service Bulletin/Repair Instructions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
IK1201472
Service Bulletin/Repair Instructions
Pico Scope CCOS (Crankcase Separator Test)
IK0800605
Service Bulletin/Repair Instructions
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
IK0800607
Service Bulletin/Repair Instructions
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
IK0800609
Service Bulletin/Repair Instructions
PicoScope Test for Datalink (CAN) Health Shorts & opens
IK0800610
Service Bulletin/Repair Instructions
PicoScope Test Resistance and Ohmmeter
IK0800611
Service Bulletin/Repair Instructions
PicoScope Wheel Speed Sensor Test
IK1201469
Service Bulletin/Repair Instructions
PicoScope Test One Channel RCT
IK1600133
Service Bulletin/Repair Instructions
Textured surfaces on painted plastic bumpers, chassis side skirts, and fender extendtions
IK1600136
Service Bulletin/Repair Instructions
Primer recommendation for matching textured panels to smooth panels for field repairs
IK1600131
Service Bulletin/Repair Instructions
Cab water leak troubleshooting tips; HX with steel cab only
IK1201464
Service Bulletin/Repair Instructions
High Pressure Fuel Pump external leaks from weep hole. only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
IK0800080
Service Bulletin/Repair Instructions
J1939 Data Link Troubleshooting
IK1000003
Service Bulletin/Repair Instructions
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
IK2600251
Service Bulletin/Repair Instructions
How to obtain As built parameter list
IK2600254
Service Bulletin/Repair Instructions
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
IK1201299
Service Bulletin/Repair Instructions
Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
IK1201458
Service Bulletin/Repair Instructions
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
IK0700112
Service Bulletin/Repair Instructions
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
IK1900259
Service Bulletin/Repair Instructions
Day cab roof air deflector causing loud vibration noise at highway speed
IK0500038
Service Bulletin/Repair Instructions
Steering Shake, Shimmy, Shudder, Wobble, Steering Vibration; only models built with 14K weight rated axles or lower
IK2600128
Service Bulletin/Repair Instructions
A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters
IK1500074
Service Bulletin/Repair Instructions
Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
IK1600233
Service Bulletin/Repair Instructions
Cab Lean Concern
IK0800504
Service Bulletin/Repair Instructions
Repair Procedures for Vehicles Struck by Lightning
IK0800284
Service Bulletin/Repair Instructions
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
IK0800475
Service Bulletin/Repair Instructions
Radio Diagnostics and Information
IK1600258
Service Bulletin/Repair Instructions
Cleaning and Disinfecting Trucks and Buses
IK0400159
Service Bulletin/Repair Instructions
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
IK1900257
Service Bulletin/Repair Instructions
Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector
IK1500085
Service Bulletin/Repair Instructions
LT / ProStar Fuel Tank Unable to Fill; only sleeper models
IK1600207
Service Bulletin/Repair Instructions
Wind noise at upper side of cab door due to door out of alignment
IK0700097
Service Bulletin/Repair Instructions
NEW Ultrasonic DEF Head Unit; All SCR vehicles
IK0800444
Service Bulletin/Repair Instructions
Driver Information Display (VIS/DID) screen fails to boot up.
IK0700079
Service Bulletin/Repair Instructions
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
IK1201433
Service Bulletin/Repair Instructions
Only models built with Cummins X15; Fault Code 7125
IK0800092
Service Bulletin/Repair Instructions
The First Check to make when Troubleshooting any Body Controller or ESC Issue
K1200716
Service Bulletin/Repair Instructions
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
IK0800085
Service Bulletin/Repair Instructions
ProStar Electrical System Load Shed Feature 08XEV
IK1300159
Service Bulletin/Repair Instructions
Fuller Advantage Series Transmission Power and Ground; only models with A26 or Cummins X15 engines
18521
Service Bulletin/Repair Instructions
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification and proper diagnosis. In addition, Diesel Exhaust Fluid (DEF) quality sensor monitors will be corrected to proper operating function.
IK0800503
Service Bulletin/Repair Instructions
ISB Starting System Diagnostics; Only models built with cummins ISB engines
IK0800059
Service Bulletin/Repair Instructions
Brake Lights Staying On
IK0800017
Service Bulletin/Repair Instructions
Programing New Key Fobs
59310-004
Service Bulletin/Repair Instructions
Hendrickson Assembly Instructions; Transverse Torque Rods
IK0800579
Service Bulletin/Repair Instructions
Xantrex 1200W Power Inverter Information; only models with feature code 0008XLD
IK0800510
Service Bulletin/Repair Instructions
Cooper Bussmann Inverter Information/Diagnostics; only models with feature code 0008XDM or 0008XDN and built after 05/12/2014
IK0800130
Service Bulletin/Repair Instructions
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
IK0800460
Service Bulletin/Repair Instructions
Build to VIN Wiring Harnesses
IK0300047
Service Bulletin/Repair Instructions
Improved Bushings for Hendrickson Torque Rods
IK0400077
Service Bulletin/Repair Instructions
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
IK0800564
Service Bulletin/Repair Instructions
Child Checkmate is not functioning correctly; Only buses with features 47EXC, 47EXD, 47EXE built from 4/18/16 to 5/15/17
4328530R1
Service Bulletin/Repair Instructions
Tool Instruction - BCM Programming Harness
IK1900172
Service Bulletin/Repair Instructions
Espar Airtronic Heater Diagnostic Guide; only models with Feature code 16VTV
IK1900168
Service Bulletin/Repair Instructions
Fifth Wheel Jaw Unlock; only models with Feature 595BAW or 597017 - electronic Jaw release
IK0800538
Service Bulletin/Repair Instructions
SCR Aftertreatment Harness Replacement
IK0900127
Service Bulletin/Repair Instructions
Heater Hose Chafing; Only models built with N13 engine
IK0800326
Service Bulletin/Repair Instructions
Auto Start Stop Troubleshooting; only ProStar with feature code 0008TSJ
Rec17V-792_2017-
Service Bulletin/Repair Instructions
The fire extinguishers may become clogged or require excessive force to activate. In certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. Only equipped with Kidde model FC5 and FC10 fire extinguishers identified by International part numbers 1696423C2 and 1696423C3 and installed post production at Navistar?s Truck Sales Processing Center (TSPC).
IK4300001
Service Bulletin/Repair Instructions
Updating OnCommand Link with Accelerator
IK1200921
Service Bulletin/Repair Instructions
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
IK2700100
Service Bulletin/Repair Instructions
OnCommand EZ-Tech
IK2500511
Service Bulletin/Repair Instructions
Using Supplier Software to Check DTCs
IK0800554
Service Bulletin/Repair Instructions
Telematic Installation Guidelines; only Units with 500K Data Link
IK0800341
Service Bulletin/Repair Instructions
Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
REC17507
Service Bulletin/Repair Instructions
The castellated nut and cotter pin that fastens the tie rod end to the steering knuckle may have not been tightened to their specified assembly torque and over time may loosen resulting in looseness in steering; Commercial Vehicles only.
IK0800508
Service Bulletin/Repair Instructions
SCR Chassis Overlay Instruction
REC17504
Service Bulletin/Repair Instructions
The recalibration will remove engine aftertreatment system faults during reset while ensuring required driver warning remains.
IK0700096
Service Bulletin/Repair Instructions
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
IK0800546
Service Bulletin/Repair Instructions
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
IK2900030
Service Bulletin/Repair Instructions
Dealer EZ-Tech and Diagnostic Software Support Resource Center
IK1201363
Service Bulletin/Repair Instructions
CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
IK0800445
Service Bulletin/Repair Instructions
Controller Updates for 500k Baud; only vehicles with 500k baud data link
IK1201360
Service Bulletin/Repair Instructions
Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
IK2700090
Service Bulletin/Repair Instructions
OnCommand EZ-Tech Download Center
REC17502
Service Bulletin/Repair Instructions
The air dryer mounting bracket may fracture, which could cause the air dryer to separate from the vehicle frame with possible airline separation from the dryer, resulting in air system leaks or loss of air pressure to the brake system.
AFC16906
Service Bulletin/Repair Instructions
The Wingman Fusion camera software has an issue in determining the regional settings. This can cause fault codes, warning lights and disabling certain functions of the Wingman Fusion system. Wingman radar-only collision mitigation remains intact.
IK0800333
Service Bulletin/Repair Instructions
Parasitic Battery Load and Predelivery Storage Recommendations
REC16509
Service Bulletin/Repair Instructions
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification and proper diagnosis.
IK0800537
Service Bulletin/Repair Instructions
DM harness inspection; Only with Steering Column feature code 05710
IK0500058
Service Bulletin/Repair Instructions
Steering Fluids
IK1201102
Service Bulletin/Repair Instructions
Low Coolant Switch Diagnostics; only with Cummins ISX
REC16512
Service Bulletin/Repair Instructions
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification and proper diagnosis; only with 2016 compliant N13 engines and 500K baud communications network.
IK1201248
Service Bulletin/Repair Instructions
Cooling System Flush Procedure
IK1600183
Service Bulletin/Repair Instructions
Offensive Odors Inside Cabin
IK1600116
Service Bulletin/Repair Instructions
Mirror / Map Light / Visor LED Lighting Up when CB MIC is Keyed
REC16508
Service Bulletin/Repair Instructions
The battery terminal mounted cube fuse connection that supplies power to the cab may possibly break, resulting in loss of power to the cab.
IK1600222
Service Bulletin/Repair Instructions
POWER WINDOW BINDING
IK1100031A
Service Bulletin/Repair Instructions
HARD TO CRANK CONDITION ON VEHICLES WITH HYDRAULIC CLUTCH LINKAGE AND SOLO CLUTCH
IK0400140
Service Bulletin/Repair Instructions
AIR COMPRESSOR RETROFIT FOR PROSTAR MODELS EQUIPPED WITH 2010 EPA AND NEWER MAXXFORCE 11 & 13 ENGINES AND FEATURE CODE 04SPL
IK0400057
Service Bulletin/Repair Instructions
NEW BRAKE LIGHT OPERATION; PROSTAR AND LONESTAR WITH AIR BRAKES
IK1200029
Service Bulletin/Repair Instructions
RADIATOR INTERNAL RESTRICTION AND FLUSH PROCEDURE
IK0800525
Service Bulletin/Repair Instructions
CUBE FUSE INSTALLATION AFTER MAINTENANCE WHEN EQUIPPED WITH FEATURE 0008WSP
IK1600201
Service Bulletin/Repair Instructions
PROSTAR SLEEPER CAB STRUT NOISE OR AIR LEAKS
IK1900223
Service Bulletin/Repair Instructions
Air Conditioning Electrical Diagnostics
IK1900228
Service Bulletin/Repair Instructions
2010 and Newer Vehicle Air Conditioning Diagnostics (Start Here)
IK0800441
Service Bulletin/Repair Instructions
Adding an Electronic Trailer Brake Controller
TT7829EN
Service Bulletin/Repair Instructions
Tech Tip to aid technicians in the efficient removal and installation of a TC10 transmission
IK0400088
Service Bulletin/Repair Instructions
Brake Single Hot Wheel End Service Procedure
MIN16110
Service Bulletin/Repair Instructions
Load Sensor 90 Degree Fitting
IK-1201314
Service Bulletin/Repair Instructions
PERFORMING RELATIVE COMPRESSION TEST AND MISFIRE TEST WITH CPA TOOL
IK-1200915
Service Bulletin/Repair Instructions
MISFIRE DIAGNOSTICS IBB; SPN132(X) - FMI 31
IK-1201320
Service Bulletin/Repair Instructions
IK1201320 - EGR SLOW RESPONSE DIAGNOSTICS; 2659 - 10
IK-1500051
Service Bulletin/Repair Instructions
IK1500051 - DAVCO FUEL PRO 382 TECHNICAL MANUAL, INSTALLATION, DIAGNOSTICS, AND SERVICE
IK-1201253
Service Bulletin/Repair Instructions
IK1201253 - EXHAUST MANIFOLD SERVICE PROCEDURES
IK-1201326
Service Bulletin/Repair Instructions
IK1201326 - SERVICE PARTS DAMAGED NEW TURBOCHARGER OIL SUPPLY TUBE
IK-2600225
Service Bulletin/Repair Instructions
IK2600225 - 500K BAUD ENGINE MODULE PROGRAMMING
IK-0500056
Service Bulletin/Repair Instructions
NEW STEERING SHAFT HEX BOLT
IK1201323
Service Bulletin/Repair Instructions
ISX15 Aftertreatment Fuel Injector Replacement
MIN16102
Service Bulletin/Repair Instructions
Certain 500K Baud compliant Body Control Module replacement
MIN16103
Service Bulletin/Repair Instructions
Certain DEF Sensor / Pickup Assembly / DEF Tank Replacement
MIN16104
Service Bulletin/Repair Instructions
Certain vehicles with Exempt Emissions Label.
AFC15903
Service Bulletin/Repair Instructions
Cummins ISX engine and Horton 2-speed fan drive may experience a condition where the mounting bracket of the fan drive is contacting the engine?s front cover.
IK0600018
Service Bulletin/Repair Instructions
Driveline Replacement - JB Hunt only
IK0800427
Service Bulletin/Repair Instructions
Active Faults During Load Shed
IK0900105
Service Bulletin/Repair Instructions
Retrofiting a Horton VMaster(Stratis) fan drive to Horton 2spd air operated fan drive on N13 or MaxxForce 13 engines
IK1900245
Service Bulletin/Repair Instructions
ESPAR D5 Hydronic Diagnostic Guide
REC15516
Service Bulletin/Repair Instructions
A spacer assembly in the transmission may lack the necessary clearance and could force the main shaft key out of position
MIN15112
Service Bulletin/Repair Instructions
Trailer Socket / Air Line Bracket Interference
IK1100031
Service Bulletin/Repair Instructions
Hard to Crank Condition with Hydraulic Clutch Linkage and Solo Clutch
IK0400144
Service Bulletin/Repair Instructions
Standard to Heavy Duty Brake Chamber Replacement
MIN15111
Service Bulletin/Repair Instructions
Battery Feed Wire A14XX may be missing for the No Idle HVAC or No Idle Heater Fuse
IK0400125
Service Bulletin/Repair Instructions
NAVISTAR: VARIOUS TYPES NAVISTAR VEHICLES WILL BE RECEIVING UPDATES ON THE REAR S CAM TUBE/ BRACKET PARTS. *TA UPDATED 9/10/15 *CN
REC15511
Service Bulletin/Repair Instructions
An incomplete weld at the flared section of the tail pipe may cause a crack in the weld, which may result in partial or full separation of the tail pipe from the vertical exhaust pipe.
REC15504
Service Bulletin/Repair Instructions
A diaphragm in the spring brake chamber may not be seated fully into the pressure plate and may cause internal leakage in the chamber, resulting in the parking brake to not fully release and drag.
MIN15107
Service Bulletin/Repair Instructions
vehicles equipped with 2015 N13 engines (0510AAA) and Eaton Fuller Ultrashift Transmissions, built between 20 January 2015 and 31 March 2015, may have a transmission controller programmed for speed controlled shifting where feature code and application code specifies torque control shifting programming.
MIN-15106
Service Bulletin/Repair Instructions
IMPROPER TERMINAL POSSIBLY INSTALLED ON HARNESS PART NUMBER 4047811C91. TERMINAL WILL NOT ALLOW HARNESS TO BE INSTALLED BEFORE MODIFYING HARNESS AND REQUIRES REPLACEMENT *CN
IK1600023
Service Bulletin/Repair Instructions
MIRROR REPAIR PROCEDURES AND REPLACEMENT PARTS AVAILABILITY
IK0800485
Service Bulletin/Repair Instructions
Cluster Software Update Instructions
IK0800463
Service Bulletin/Repair Instructions
HIGH OR SPIKING VOLTAGE ONLY WITH LEECE-NEVILLE ALTERNATOR USING REMOTE VOLTAGE SENSE
IK0800414
Service Bulletin/Repair Instructions
Power Windows Stop Randomly
IK0800411
Service Bulletin/Repair Instructions
Body Controller Resource Center
IK0800412
Service Bulletin/Repair Instructions
Headlight Operation and Troubleshooting; only Post 2007 Vehicles Built with a Body Controller
IK0800172
Service Bulletin/Repair Instructions
NAVISTAR: VARIOUS TYPES OF VEHICLES INCLUDING LONESTAR, PROSTAR, 8600, AND 7600 VEHICLES WILL NEED AN OPERATION TO IMPROVE THE CAB CIRCUIT GROUNDS. 7/17/15 *TA
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.